Peerless-AV LCT100S Installation

Installation and Assembly:
Desktop Mount with Desk Clamp and Grommet for 19" - 30" LCD Screens
Models: LCT100S
GROMMET INSTALLATION DESK CLAMP INSTALLATION
Max Load Capacity: 20 lbs (9 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 07-25-11 SHEET #: 090-9202-5 07-16-13
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum Load Capacity. See page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Tools Needed for Assembly
• phillips screwdriver
• drill
• 3/8" (10 mm) drill bit
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Mounting Surface .............................................................................................................................................4
Attaching Adapter Plate Assembly to Screen .........................................................................................................................5
Cable Management ................................................................................................................................................................6
ISSUED: 07-25-11 SHEET #: 090-9202-5 07-16-13
y
Before you begin, make sure all parts shown are included with your product.
Parts List
AB
Description
A column assembly 1 B adapter plate assembly 1 C grommet assembly 1 D round rubber pads 2 E square rubber pads F M4 x 12 mm phillips screw G M4 x 25 mm phillips screw H spacer 4
I 4 mm allen wrench 1
J 2.5 mm allen wrench 1 K cable clip L cable tie
Parts may appear slightly different than illustrated.
D
E
Qt
2 4 4
C
1 5
FG H
KL
J
I
ISSUED: 07-25-11 SHEET #: 090-9202-5 07-16-13
Clamp Installation Method
Apply four rubber pads (D, E) to bottom of column
1
assembly (A) as shown below. Attach column assembly (A) to mounting surface with a maximum thickness of 3".
Skip to step four.
Grommet Installation Method
Remove clamp assembly from column assembly
1
(A) as shown in fi gure 1.1. Remove mounting plate from grommet assembly (C) and attach to column assembly (A) with four M6 x 8 mm screws using 4 mm allen wrench (I) as shown in fi gure 1.2.
g. 1.1
A
M6 X 8 MM
SCREWS
D
E
Apply four rubber pads (D, E) to bottom of column
2 3
assembly (A) as shown below.
A
g. 1.2
A
CLAMP
ASSEMBLY
MOUNTING
PLATE
M6 X 8 MM
SCREWS
Drill a 3/8" (10mm) dia. hole through mounting
surface with a maximum thickness of 3". Place
column assembly (A) on mounting surface and secure using grommet assembly (C).
A
E
D
A
C
ISSUED: 07-25-11 SHEET #: 090-9202-5 07-16-13
Attaching Adapter Plate Assembly to Screen
WARNING
• Tighten screws so adapter plate assembly is fi rmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns into the screen inserts or if screws bottom out and plate is still not tightly secured, damage may occur to screen or product may fail.
To prevent scratching the screen, set a cloth on a fl at, level surface that will support the weight of the screen. Place
4
screen face side down. If screen has knobs on the back, remove them to allow the adapter plate assembly to be attached. Place adapter plate assembly (B) on back of screen.
Choose hole pattern as shown in detail 1. FOR DISPLAYS WITH FLAT BACKS: Attach adapter plate assembly (B) to display using four 12mm screws
(F) as shown in fi gure 4.1. FOR DISPLAYS WITH RECESSED BACKS: Attach adapter plate assembly (B) to display using four 25mm
screws (G) and four spacers (H) as shown in fi gure 4.2.
B
VESA 100mm
g. 4.1
VESA 75mm
VESA 75mm
DETAIL 1
F
VESA 100mm
B
g. 4.2
G
H
ISSUED: 07-25-11 SHEET #: 090-9202-5 07-16-13
Loosen and position lock collar to desired height and retighten lock collar as shown in fi gure 5.1.
5
adapter plate assembly (B) onto column assembly (A) and let it rest on lock collar as shown in fi gure 5.2.
Insert Tighten set screw on rear of
adapter plate assembly (B) using 2.5 mm allen wrench (J) as shown in fi gure 5.3.
g. 5.1
LOCK COLLAR
g. 5.2
LOCK COLLAR
g. 5.3
B
SET SCREW
A
Cables may be routed using cable clip (K).
6
CABLES
K
ISSUED: 07-25-11 SHEET #: 090-9202-5 07-16-13
To lock down rotation, tighten set screw shown in detail 2.
7
To lock down tilt, tighten screw shown in detail 3. To lock down swivel, tighten screw shown in detail 4.
SET SCREW
TILT SCREW
DETAIL 2
SWIVEL SCREW
360°
180°
DETAIL 3
+80/-20°
DETAIL 4
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 07-25-11 SHEET #: 090-9202-5 07-16-13
© 2013 Peerless Industries, Inc. All rights reserved.
LIMITED FIVE-YEAR WARRANTY
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of fi ve years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
In no event shall the duration of any implied warranty of merchantability or fi tness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.
damages, so the above limitation or exclusion may not apply to you.
This warranty gives specifi c legal rights, and you may also have other rights which vary from state to state.
www.peerless-av.com
© 2013 Peerless Industries, Inc.
ISSUED: 07-25-11 SHEET #: 090-9202-5 07-16-13
Loading...