Peerless-AV HDS-IWK-200 Installation

Installation and Assembly:

Indoor Wireless Integration Kit*

Model: HDS-IWK-200

* - For use with select mounts

2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerless-av.com

ISSUED: 08-23-12 SHEET #: 180-9027-2 10-30-12

Note: Read entire instruction sheet before you start installation and assembly.

WARNING

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud fi nder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

• Metal Stud Contact Qualifi ed Professional

• Brick Contact Qualifi ed Professional

• Other or unsure? Contact Qualifi ed Professional

Tools Needed for Assembly

• 7/16" open end wrench

• 5mm allen wrench

Table of Contents

Installation to Universal Adapter Bracket ................................................................................................................................5

Installation to Tilt Bracket......................................................................................................................................................13

Installation to Large PLP Adapter Plate ................................................................................................................................16

Installation to VESA 200 Adapter Plate ................................................................................................................................19

Wireless Receiver Assembly and Power Module Assembly Setup ......................................................................................20

2 of 24

ISSUED: 08-23-12 SHEET #: 180-9027-2 10-30-12

Parts List

Description Qty. Part #

wireless receiver assembly 1 180-1092

A

power module assembly 1 180-1015

B

decorative screw 1/4-20 8 520-2325

C

lock nut 1/4-20 8 530-1021

D
E cable tie .187 x 7.5 lg.
F cable tie .04 x 5.75 lg.
G cable tie anchor

4 mm allen wrench 1 560-9646

H

cable management sheath 1 590-9468

I

enclosure mounting bracket, small 4 120-1195

J

enclosure mounting bracket, large 4 120-1196

K

Parts may appear slightly different than illustrated.

8 590-1168
2 560-9711
2 590-9469

HDS-IWK-200

A

H

B

C

D

E

F

G

I

J

K

3 of 24

ISSUED: 08-23-12 SHEET #: 180-9027-2 10-30-12

S

Adapter Bracket Fasteners

M4 x 12 mm (6)

(504-9013)

M6 x 30 mm (4)

(510-9109)

M4 x 25 mm (4)

(504-1015)

M8 x 16 mm (6)

(520-9257)

Additional Wireless Components

M5 x 12 mm (4)

(520-1027)

M8 x 25 mm (4)

(520-1031)

M5 x 25 mm (4)

(520-9543)

M8 x 40 mm (4)

(520-1136)

M6 x 12 mm (4)

(520-1128)

I.D. .22" (4)

(540-1057)

I.D. .34" (4)

(540-1059)

M6 x 20 mm (4)

(520-9402)

multi-washer (6)

M6 x 25 mm (4)

(520-1208)

(580-1036)

wireless transmitter (1)

(180-1202)

3v battery (1)

(180-0008)

vga to rca adapter (1)

(180-1006)

12v power adapter (1)

(180-1004)

plastic stand (1)

(180-1205)

ir fl asher (1)

(180-1009)

remote (1)

(180-1207)

hdmi cable (2)

(600-0234)

®

READY

Quick Start Guide

Step 7 While turning on the display device the HD Flow Pro Wireless Multimedia units will be going through the startup process. This process may

PRO WIRELESS MULTIMEDIA KIT

What’s in the Box

Installation and Setup

Step 1 Connect the Transmitter to the source devices

™

Disc player, set top box, gaming console, etc.).

(Blu-ray

Tip Repeat Steps

teps

ect

3-11 to connect

ne

more than one

t

Receiver unit
(HDS200-2,
HDS200-3,
HDS200-4).

Step 3 Connect the display device (TV, monitor, projector, etc.)

tthdil d i(TV it j t t)

to the Receiver.

Step 5 Power-up the HD Flow Pro Devices.

1. Plug in the power adapter for the Transmitter and the Receiver to nearby
available power outlets.

2. Plug in the power adapter end to the Transmitter and then to the Receiver.

3. The units will automatically turn-on. The average power-on/sync time
is approximately two minutes.

© 2012 Peerless Industries, Inc. Peerless-AV™ is a trademark of Peerless Industries, Inc. All rights reserved.
HD Flow™ is a trademark of I Do It, LTD. Other parties’ marks are the property of their respective owners. hdflow.com

take up to two minutes to complete. The Power/Link indicator lights on the Transmitter and the Receiver will be flashing at first. Flashing indicates

Model No. HDS200 (-2, -3, -4)

2

Minutes

that the units are establishing a secure connection. Wait until the connection is successfully established, indicated by the Power/Link indicator
light becoming solid.

1 x Transmitter

1 x IR Extender

1 x Receiver

1 x Component Adaptor

2 x Stand

2 x Power Adapter

1 x Remote Control

1 x Quick Start Guide

1 x IR Flasher

1 x Users Manual

Power/Source
Selection Button

Step 8 Select the output that connects the Receiver to the display using

Step 9 Turn on the desired source device that is connected to

the Power/Source Selection Button or the provided remote control.

the Transmitter.
The output indicator light will become solid and the HD Flow logo will
appear on the display device.

Tip The IR window

may be easier to
locate with a direct
light shining on
sections of the
front panel of the
component device.
A small flashlight
works well.

Power/Source

Step 2 Connect the provided IR Flasher to the IR-OUT port on the Transmitter.

Selection Button

Find the location of the IR window on your source device and adhere the
IR Flasher eye directly over the IR window on your source device.

NOTE: One IR Flasher eye is to be used for one component device.

Step 10 Select the desired source or device input on the Transmitter

Step 11 Play the source device content and enjoy up to Full HD 1080p

using the Power/Source Selection Button on the remote control.

wireless entertainment experience.

Troubleshooting Tips

Transmitter and/or Receiver Indicator Lights are all Blinking:

• Check the media source resolution. The display device must be able

to support the resolution of the media source that is being streamed.

• The HD Flow Pro units are establishing a connection. It can take

Utilizing the INFO button will allow you to see the resolution data that

up to two minutes for the HD Flow Pro units to establish a complete

the display device supports. If the display device supports the highest

connection. If after two minutes have passed and the units have not

resolution of 720p but the source device is outputting 1080p content,

established a connection, unplug the power cable, wait 30 seconds

the content needs to be down-scaled to the maximum resolution of the

and reconnect the power supply to the units.

display device, in this case 720p.

Transmitter or Receiver Power Indicator Light is OFF:

Step 4 Install the IR Extender by plugging in the provided IR Extender in to

the IR-IN port on the Receiver and adhering the other end of the IR Extender
to a vertical surface near the output device. Ensure that the IR Extender is in
a line of sight to the remote control that controls your source devices.

NOTE: For Multicast models, receivers two, three and four do not come with an IR Extender. Additional IR Extenders
(HDS-IRE) can be purchased separately; visit peerless-av.com for more information.

Step 6 Turn on your display device (TV, monitor, projector, etc.).

• Check and verify the power supply connection.

Transmitter Input Indicator Light Blinks:

• Make sure that your source device is turned ON and the cable

is properly connected.

• Verify that the Transmitter is set to the appropriate input port.

• Check the resolution from your source device. This may need to

be changed to a resolution supported by the HD Flow Pro Wireless
Multimedia Kit. Reference the Resolution Chart in the HD Flow Pro
Manual for compatibility. Reference your source devices’ manual
for instruction on changing the output resolution.

Receiver Power Indicator Light Blinks:

• Verify that the HD Flow Pro Transmitter and Receiver are within

the recommended range of 131 feet. Physical obstructions such as
walls, floors and ceilings between the Transmitter and Receiver may
decrease the strength of the connection signal and reduce the overall
transmission range.

If a connection has been established and the HD Flow logo can be seen
on the display device, but content is not playing:

• Make sure that the input/output cables are properly connected.

• Verify that the Transmitter is set to the appropriate input port.

Receiver Output Indicator Light Blinks:

• Make sure that your display device, source device and the HD Flow Pro units

are all turned ON and the Receiver is properly connected to the output device.

• Verify that the Receiver is set to the appropriate output port.

• Check the resolution setting of your source device. This may need to be

changed to a resolution supported by the HD Flow Pro unit. Reference

the Resolution Chart in the HD Flow Pro Manual for compatibility.

Reference your source devices’ manual for instruction on changing

the output resolution.

If the above troubleshooting tips do not resolve the issues for a unicast setup,

please reference the Factory Reset Section of the HD Flow Pro Manual. For a

multicast system configuration, please contact Peerless-AV Customer Care at

800-856-2112 for further instruction.

Warning Do not place the HD Flow

Pro units near other devices that
emit excessive amounts of heat.
Increased temperatures may
cause the HD Flow Pro Transmitter
or Receiver unit to malfunction
or stop working.

Quick Start Guide for HD Flow Pro Wireless Multimedia Kit - LIT-0906

install guide (1)

(LIT-0905)

User Manual and Installation Guide

Pro Wireless Multimedia Kit

Models:

HDS200
HDS200-2
HDS200-3

®

READY

HDS200-4

ISSUED: 06-12-12 SHEET #: 180-9023-1

instruction sheet (1)

(180-9023)

4 of 24

ISSUED: 08-23-12 SHEET #: 180-9027-2 10-30-12

Installation to Universal Adapter Bracket

NOTE: If display has a VESA 400 horizontal

mounting pattern, skip to step 1-3 on page 6.
NOTE: For VESA 200x200 or VESA 200x100

mount hole patterns, skip to step 1-8 on page 9.

1/4-20 x 1.25" SCREWS

1-1

1-2

Remove four 1/4-20 x .6" screws using a 5 mm
allen wrench and loosen two 1/4-20 x 1.25" screws
1/2 turn to allow for display bracket adjustment.

1/4-20 x .6" SCREWS

To prevent scratching the display, set a cloth on a fl at, level surface that will support the weight of the display.
Place display face side down and refer to display manufacturers instructions for removing obstructions from the
back of the display. Adjust display brackets to align with display mounting holes.

Measure horizontal mounting hole pattern and choose fi xed stop-position from chart below.

horizontal mounting hole pattern fixed stop-position

10-3/4" - 16-1/16" (273 - 408 mm) #1
15-1/16" - 21-9/16" (383 - 548 mm) #2
20-7/16" - 27-9/16" (519 - 700 mm) #3

FIXED STOP-POSTION #3

FIXED STOP-POSTION #2

FIXED STOP-POSTION #1

5 of 24

ISSUED: 08-23-12 SHEET #: 180-9027-2 10-30-12

Wireless Receiver Assembly and Power Module Assembly Installation

1-3

NOTE: The Wireless Receiver Assembly and Power Module Assembly position can be interchanged based on the
display's connector panel location. Install Wireless Receiver Assembly on the side closest to the connector panel.

Loosely attach the small enclosure mounting brackets (J) on the wireless receiver assembly (A) with two 1/4-20
decorative screws (C) and two 1/4-20 nuts (D) as shown in fi g. 1.1. NOTE: The enclosure mounting bracket can
be installed with the inside notch facing downward if additional side-to-side adjustment is needed. Attach the
mounting brackets (J), open end of notch facing downward, to the left display bracket with two 1/4-20 decorative
screws (C) and two 1/4-20 nuts (D) as shown in fi g. 1.2.

Position the wireless receiver assembly approximately 1/4" from the universal adapter as shown in detail 2. Once
in position, tighten the four 1/4-20 decorative screws (C) using 4mm allen wrench (H).

C

1-4

A

1/4"

DETAIL 1

DISPLAY BRACKET

D

A

J

INSIDE NOTCH

fi g. 1.1

Loosely attach the enclosure mounting brackets (J) on the power module assembly (B) with two 1/4-20 decorative
screws (C) and two 1/4-20 nuts (B) as shown in fi g. 1.3. NOTE: The enclosure mounting bracket can be installed
with the inside notch facing downward if additional side-to-side adjustment is needed. Attach the mounting
brackets (J), open end of notch facing downward, to the right display bracket with two 1/4-20 decorative screws
(C) and two 1/4-20 nuts (D) as shown in fi g. 1.4.

Position the power module assembly approximately 1/4" from the universal adapter as shown in detail 1. Once in
position, tighten the four 1/4-20 decorative screws (C) using 4mm allen wrench (H).

D

C

fi g. 1.2

D

INSIDE NOTCH

B

C

J

fi g. 1.3

6 of 24

D

DISPLAY
BRACKET

C

fi g. 1.4

ISSUED: 08-23-12 SHEET #: 180-9027-2 10-30-12

Installing Adapter Brackets to Display

WARNING

• Tighten screws so display brackets are fi rmly attached to display. Do not tighten with excessive force.
Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing
screw heads to become detached. Tighten to 40 in. • lb. (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.

1-5

Select the screws from the baffl ed fastener pack that best fi t your display and secure to display following step 1-6
on page 8.

NOTE: Top and bottom mounting holes must be used for attaching display brackets. Middle holes should also be
used where the fasteners and displays allow.

Verify that all holes are properly aligned, then tighten screws using a phillips screwdriver.

CENTER DISPLAY BRACKETS VERTICALLY AND

HORIZONTALLY ON BACK OF DISPLAY

DISPLAY

X

DISPLAY BRACKETS

Y

NOTE: "X" dimensions should be equal.

"Y" dimensions should be equal.

7 of 24

Y

ISSUED: 08-23-12 SHEET #: 180-9027-2 10-30-12

X

1-6

NOTE: Wireless Receiver and Power Box
removed for clarity.

Begin with the longest length screw, hand thread
screw through multi-washer, display brackets and
spacer in that order into display as shown below.
Screw must make at least three full turns into the
mounting hole and fi t snug into place. Do not over
tighten. If screw cannot make three full turns into
the display, select a shorter length screw from
the baffl ed fastener pack. Repeat for remaining
mounting holes, level display brackets and tighten
screws.

DISPLAY

B

1/4-20 x 1.25" SCREWS

SPACER

MULTI-WASHER

SCREW

1-7

Center display brackets horizontally and
vertically on back of display. Tighten two 1/4-20
x 1.25" screws. Reinstall four 1/4-20 x .6" screws
using a 5 mm allen wrench into appropriate
fi xed-stop position from chart on page 5.

Skip to step 5.

1/4-20 x .6" SCREWS

8 of 24

ISSUED: 08-23-12 SHEET #: 180-9027-2 10-30-12