Parkside PSG 50 B2 User Manual
POWER CARVING TOOL PSG 50 B2
POWER CARVING TOOL
Operation and Safety Notes
Translation of original operation manual
MOTORSKÄRARE
Bruksanvisning och säkerhetsanvisningar
Översättning av bruksanvisning i original
MOTORSCHNITZGERÄT
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
SÄHKÖKÄ YTTÖINEN KAIVERRUSTAL TT A
Käyttö- ja turvaohjeet
Alkuperäisen käyttöohjeen käännös
TRÆSNITTEMASKINE
Brugs- og sikkerhedsanvisninger
Oversættelse af den originale driftsvejledning
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin.
Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med
apparatens / maskinens funktioner.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB / IE Operation and Safety Notes Page 5
FI Käyttö- ja turvaohjeet Sivu 13
SE Bruksanvisning och säkerhetsanvisningar Sidan 21
DK Brugs- og sikkerhedsanvisninger Side 29
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 37
6
4 3
215
A
7
8
B
C D
Table of contents
Introduction
Proper use ..........................................................................................................................Page 6
Equipment ..........................................................................................................................Page 6
Scope of Delivery ..............................................................................................................Page 6
Technical details ................................................................................................................Page 6
General safety advice for electrical power tools
1. Workplace safety .........................................................................................................Page 7
2. Electrical safety .............................................................................................................Page 7
3. Personal safety ..............................................................................................................Page 8
4. Careful handling and use of electrical power tools ...................................................Page 8
5. Service ...........................................................................................................................Page 9
Safety instructions for motor carving devices ..................................................................Page 9
Original Accessories / Additional Equipment ..................................................................Page 9
Operation
Turning the Device On / Off ............................................................................................. Page 9
Inserting / replacing blade inserts ....................................................................................Page 9
Working Instructions .........................................................................................................Page 10
Maintenance and Cleaning ............................................................................Page 10
Service .............................................................................................................................Page 10
Warranty .......................................................................................................................Page 10
Disposal ..........................................................................................................................Page 11
Manufacturer’s Declaration of Conformity /
Manufacturer .............................................................................................................Page 11
5 GB/IE
The following pictograms are used in these operating instructions / on the device:
Read instruction manual!
V
W
n
Volt (AC)
~
Watts (Effective power)
Design no-load speed
0
Observe caution and safety notes!
Risk of explosion!!
Power carving tool PSG 50 B2
Q
Introduction
Please make sure you familiarise yourself
fully with the way the device works before
you
use it for the first time and that you
understand how to handle electrical power tools correctly. To help you do this please read the accompanying operating instructions. Keep these instructions
in a safe place. If you pass the device on to anyone
else, please ensure that you also pass on all the
documentation.
Q
Proper use
This carving device is intended for processing all
types of wood. For example, it can be used for
carving, renovating furniture, refurbishing antiques,
fine paint stripping and linocuts. Any other use or
modification to the drill / grinder shall be considered
as improper use and could give rise to considerable
dangers. The manufacturer will not accept liability
for loss or damage arising from improper use. Not
intended for commercial use.
Keep children away from electrical
power tools!
Caution – electric shock!
Danger to life!
Risk of loss of life by electric shock
from damaged mains lead or mains
plug!
Wear hearing protection, dust protection
mask, protective glasses and protective
gloves.
Dispose packaging and appliance in
an environmentally-friendly way!
Q
Equipment
ON / OFF switch
1
Bracket
2
Mains lead with plug
3
Ventilation slots
4
Tool holder
5
Cap nut
6
Blade inserts
7
Key
8
Q
Scope of Delivery
1 Motor carving device PSG 50 B2
3 Blade inserts
1 Key
1 Operating Instructions
Q
Technical details
Rated voltage: 230 V∼ 50 Hz
Power rating: 50 W
Stroke rate when idling: n
11500 strokes / min
0
6 GB/IE
Introduction / General safety advice for electrical power toolsIntroduction
Noise and vibration data:
Measured values for noise are determined in accordance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 60.3 dB(A)
Sound power level: 71.3 dB(A)
Uncertainty K: 3 dB
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration: 0.864 m / s
Uncertainty K = 1.5 m / s
The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different
vibration levels and in many cases they may exceed
the values given in these instructions. It is easy to
underestimate the vibration load if the electrical power tool is used regularly in particular circumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
2
2
General safety advice for
electrical power tools
Read all the safety advice
and instructions! Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electricity (by means of a mains lead) and electrical tools
powered by rechargeable batteries (without a
mains lead).
1. Workplace safety
a) Keep your working area clean and
well lit. Untidy or poorly lit working areas
can lead to accidents.
b)
inflammable liquids, gases or dusts.
c)
Distractions can cause you to lose control of
Do not work with the device
in potentially explosive environments in which there are
Electrical power tools create sparks, which can
ignite dusts or fumes.
Keep children and other
people away while you are
operating the electrical tool.
the device.
2. Electrical safety
a)
The mains plug on the device must match
the mains socket. The plug must not
be modified in any way. Do not use
an adapter plug with devices fitted
with a protective earth. Unmodified plugs
and matching sockets reduce the risk of electric shock.
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrigerators with any part of your body.
There is an increased risk of electric shock if
your body is earthed
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d)
device, to hang up the device or to pull
Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry the
the mains plug out of the mains socket.
Keep the mains lead away from heat,
oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads
increase the risk of electric shock.
.
7 GB/IE
General safety advice for electrical power tools General safety advice for electrical power tools / Operation
e) When working outdoors with an
electrical power tool always use extension cables that are also approved
for use outdoors. The use of an extension
cable suitable for outdoor use reduces the risk
of electric shock.
f) Use a residual current device (RCD)
for protection if operating the electrical power tool in a moist environment
is unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo
of carelessness when using the device can lead
to serious injury.
b)
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of electrical power tool used and work undertaken,
reduces the risk of injury.
c) Avoid unintentional operation of the
device. Check that the electrical power
tool is switched off before you connect
it to the mains, pick it up or carry it.
Accidents can happen if you carry the device
with your finger on the ON / OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing
and balance at all times. By doing this
you will be in a better position to control the
device in unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
8 GB/IE
Wear personal protective
equipment and always wear
safety glasses. The wearing of
ment
hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
that they are properly connected and
correctly used. The use of these devices
reduces the hazard presented by dust.
4.
Careful handling and use
check
of electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are undertaking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug from the socket
before you make any adjustments to
the device, change accessories or when
the device is put away. This precaution is
intended to prevent you from unintentionally
starting the device.
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone use
the device if he or she is not familiar
with it or has not read the instructions
and advice. Electrical power tools are dan-
gerous when they are used by inexperienced
people.
e) Look after the device carefully. Check
that moving parts are working properly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have damaged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this particular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those intended can lead to dangerous situations.
5. Service
a) Have your device repaired at the ser-
vice centre or by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
Safety instructions for
motor carving devices
device or the area to be worked on.
There is a danger of injury from the very sharp
attachment tools.
Always route the cable towards the back away
from the device.
In cases of danger remove the plug from the
socket immediately.
Q
Original Accessories /
Additional Equipment
Use only the accessories and additional
equipment referred to in the instructions. The use of tools or other accessories
which are not recommended in the instructions
may represent a risk of injury.
Q
Operation
Q
Turning the Device On / Off
Insert the mains plug into a socket.
In order to avoid injury, fire and health
hazards:
Secure the work piece. Use clamping
devices / a vice to hold the work piece.
It is then held more securely than with your hand.
Wear protective goggles!
There is a danger of injury from
splintering materials flying into your
eyes etc.
Wear a dust mask! During pro-
longed working with wood and par-
ticularly if materials are processed
which produce dusts that are hazardous to the
health.
Do not soak materials or areas which
are to be worked on with solvent-containing liquids. Shaving of the materials may
produce harmful / toxic vapours.
Material containing asbestos must not
be processed with this device. Asbestos
is a known carcinogen.
Under no circumstances should you p
up your hands next to or in front of the
rop
Switching on:
Press the ON / OFF switch 1 to the “I” position.
Switching off:
P
ress the ON / OFF switch 1 to the “0” positio
Inserting / replacing
blade inserts
RISK OF INJURY! Switch the
device off and pull the plug out of the mains socket
before carrying out any work on the device.
RISK OF INJURY! The blade
7
inserts
The choice of blade insert
ded task. The supplied blade inserts
for a wide range of common uses (see Fig. B–D).
have very sharp cutting edges.
Wear appropriate protective gloves
when inserting and testing the blade.
7
depends on the inten-
7
are suitable
n.
9 GB/IE
Release the union nut 6 by turning it anticlock-
wise using the key
8
.
If necessary, remove the blade insert 7. Push
another blade insert into the tool holder
5
far as it will go.
Tighten the union nut 6 again by turning it
clockwise using the key
8
.
Check that the blade insert 7 is securely held
in place.
Q
Working Instructions
Always work away from the body.
Q
Maintenance and Cleaning
Q
Warranty
The warranty for this appliance is for 3 year
from the date of purchase. The appliance
as
has been manufactured with care and meticulously examined before delivery.
retain your receipt as proof of purchase. In
the event of a warranty claim, please mak
contact by telephone with our Service Department. Only in this way can a post-free
despatch for your goods be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile components,
e.g. buttons or batteries. This product is for private use
only and is not intended for commercial use.
s
Please
e
Before performing any cleaning
or maintenance work, always remove the mains
plug from the socket.
The device must be clean, dry and free of oil
or grease at all times.
Make sure that the ventilation slots 4 are
always clear.
Clean the tool holder 5 regularly.
Clean the blades of wood or other materials
and residual dirt.
No liquids must be allowed to enter the interior
of the device.
Use a soft, lint-free cloth to clean the housing.
Never use petrol, solvents or cleaning agents
which attack plastic.
Q
Service
Have your device
repaired at the service centre or by
qualified specialist personnel using
original manufacturer parts only. This
will ensure that your device remains safe to use.
If the plug or lead
needs to be replaced, always have
the replacement carried out by the
manufacturer or its service centre. This
will ensure that your device remains safe to use.
The warranty is void in the case of abusive and improper handling, use of force and internal tampering
not carried out by our authorized service branch. Your
statutory rights are not restricted in any way by this
warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0,10 GBP/Min.)
e-mail: kompernass@lidl.co.uk
IAN 66132
IE
Service Ireland
Tel: 1890 930 034
(0,08 EUR/Min. (peak)
0,06 EUR/Min. (off peak))
e-mail: kompernass@lidl.ie
IAN 66132
10 GB/IE
Disposal / Manufacturer’s Declaration of Conformity / ManufacturerOperation / Maintenance and Cleaning / Service / Warranty
Q
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electric tools
in the household waste!
In
accordance with European Directive 200
about waste electrical and electronic equipment
and its transposition into national legislation, worn
out electric tools must be collected separately and
taken for environmentally compatible recycling.
Contact your local refuse disposal authority for
more details of how to dispose of your worn out
electrical devices.
2 / 96 / EC
Q
Manufacturer’s Declaration of
Conformity / Manufacturer
We, Kompernaß GmbH, the person responsible for
documents: Mr Semi Uguzlu, Burgstr. 21, D-44867
Bochum, Germany, hereby declare that this product
complies with the following standards, normative
documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic compatibility
(2004 / 108 / EC)
Applicable harmonized standards
EN 60745-1:2009+A11
EN 55014-1:2006+A1
EN 55014-2:1997+A1+A2
EN 61000-3-2:2006+A1+A2
EN 61000-3-3:2008
Type / Device description:
Power carving tool PSG 50 B2
Date of manufacture (DOM): 12–2011
Serial number: IAN 66132
Bochum, 31.12.2011
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifications in the course of further development.
11 GB/IE
12
Sisällysluettelo
Aluksi
Määräystenmukainen käyttö ............................................................................................. Sivu 14
Varustus .............................................................................................................................. Sivu 14
Toimitukseen kuuluu ........................................................................................................... Sivu 14
Tekniset tiedot ..................................................................................................................... Sivu 14
Sähkötyökaluja koskevat yleiset turvaohjeet
1. Työpaikkaturvallisuus..................................................................................................... Sivu 15
2. Sähköturvallisuus ........................................................................................................... Sivu 15
3. Henkilöiden turvallisuus ................................................................................................. Sivu 16
4. Sähkötyökalujen huolellinen käsittely ja käyttö ........................................................... Sivu 16
5. Huolto ............................................................................................................................. Sivu 17
Moottori veistolaitteen turvallisuusohjeet .......................................................................... Sivu 17
Alkuperäiset varusteet / -lisälaitteet ................................................................................... Sivu 17
Käyttö
Päälle- / poiskytkentä ......................................................................................................... Sivu 17
Pariston paikoilleen asetus / vaihto ................................................................................... Sivu 17
Työohjeet ............................................................................................................................ Sivu 17
Huolto ja puhdistus ................................................................................................ Sivu 18
Huolto................................................................................................................................ Sivu 18
Takuu ................................................................................................................................. Sivu 18
Hävittäminen .............................................................................................................. Sivu 18
Yhdenmukaisuusvakuutus / Valmistaja............................................... Sivu 19
13 FI
Aluksi Aluksi / Sähkötyökaluja koskevat yleiset turvaohjeet
Tässä käyttöohjeessa / laitteessa käytetään seuraavia kuvakkeita:
Lue käyttöohje! Pidä lapset loitolla sähkötyökalusta!
V
W
n
Voltti (Vaihtojännite) Varo sähköiskua! Hengenvaara!
~
Watti (vaikutusteho)
Mittaus-tyhjäkäyntiluku
0
Huomioi varoitus- ja turvaohjeet!
Räjähdysvaara!
Sähkökäyttöinen kaiverrustaltta
PSG 50 B2
Q
Aluksi
T
utustu ennen käyttöönottoa laitteeseen, se
käyttöohjeisiin ja sähkölaitteita koskeviin
yleisiin turvallisuusohjeisiin. Lue tämä käyttö-
opas huolella. Säilytä käyttöopas huolellisesti. Saatat
myöhemmin tarvita sen tietoja. Jos luovut laitteesta,
anna uudelle omistajalle myös kaikki laitteen asiakirjat.
Q
Varustus
PÄÄLLE- / POIS -kytkin
1
Laitteen sanka
2
Verkkojohto pistokkeella
3
Ilmarako
4
n
Työkalun kiinnitin
5
Hattumutteri
6
Taltat
7
Avain
8
Q
Toimitukseen kuuluu
Viallisen verkkojohdon tai pistokkeen
käyttöön liittyvän sähköiskun aiheuttama
hengenvaara!
Käytä kuulonsuojainta, hengitys-/
pölysuojainta, suojalaseja ja suojakäsineitä.
Hävitä pakkaus ja laite ympäristöystävällisesti!
Q
Määräystenmukainen käyttö
Tämä veistolaite on tarkoitettu kaikkien puulajien
käsittelyyn. Sitä voidaan esimerkiksi käyttää huonekalujen veistoon ja korjaukseen, antiikkiesineiden
entisöintiin, hienoon värinpoistoon ja linoleumileikkaukseen. Jokaista muuta käyttöä tai laitteen muutamista pidetään ei-määräystenmukaisena ja sisältää
huomattavia onnettomuusvaaroja. Määräystenvastaisesta käytöstä syntyneistä vahingoista valmistaja
ei ota mitään vastuuta.
14 FI
1 sähkökäyttöinen kaiverrustaltta PSG 50 B2
3 talttaa
1 avain
1 käyttöohje
Q
Tekniset tiedot
Nimellisjännite: 230 V∼ 50 Hz
Nimellisteho: 50 W
Tyhjäkäynti-iskuluku: n
11500 min
0
-1
Loading...