Parkside PNS 300 B2 Original Instructions Manual
2-SPEED POWER DRILL
2-SPEED POWER DRILL
Original instructions
IAN 321840
PNS 300 B2
1
10
9
8
2
7
6
12
11
3
4
5
02
A
B
DC
9
8
E
G
9
8
11
F
1
4
6
H
10
3
7
03
Table of contents
1. Introduction ......................................................................................................................................... 05
Symbols used ...............................................................................................................................................................................................05
Scope of delivery ......................................................................................................................................................................................05
Parts list ............................................................................................................................................................................................................05
2. Technical data .................................................................................................................................... 05
3. Safety ...................................................................................................................................................... 06
Proper use ......................................................................................................................................................................................................06
Residual risks ................................................................................................................................................................................................06
General safety instructions for power tools ..............................................................................................................................06
Safety warnings for drills ......................................................................................................................................................................08
4. Before Use ........................................................................................................................................... 09
Check the drill and scope of delivery ...........................................................................................................................................09
Insert the drill bit or bit holder (Fig A) ...........................................................................................................................................09
Removing / mounting the chuck (Fig. B, C) ..............................................................................................................................09
Using the bit holder (Fig. D)................................................................................................................................................................09
5. Usage ...................................................................................................................................................... 09
Mains connection ......................................................................................................................................................................................09
Switching on and off (Fig. E) ..............................................................................................................................................................09
Speed selection (Fig. F) .........................................................................................................................................................................10
Forward / reverse switch (Fig G) ....................................................................................................................................................10
Driving screws (Fig. H) ...........................................................................................................................................................................10
Drilling ..............................................................................................................................................................................................................10
Work instructions .......................................................................................................................................................................................10
6. Maintenance, cleaning, storage and transport........................................................... 11
Maintenance ................................................................................................................................................................................................11
Cleaning..........................................................................................................................................................................................................11
Storage ............................................................................................................................................................................................................11
Transport .........................................................................................................................................................................................................11
7. Troubleshooting ............................................................................................................................... 12
8. Noise and vibrations levels ...................................................................................................... 13
9. Recycling ............................................................................................................................................... 13
Disposal of packaging ...........................................................................................................................................................................13
Disposal of the drill ...................................................................................................................................................................................13
10. Declaration of conformity....................................................................................................... 13
11. Warranty ........................................................................................................................................... 14
12. Service ................................................................................................................................................. 14
04
1. Introduction
Congratulations on the purchase of your new
product. You have chosen a high quality product
with this purchase. This operating manual is an
integral part of this 2-speed mains-operated drill
(hereafter referred to only as the „drill“). It contains
important instructions on safety, use and disposal
of the product. Please familiarise yourself with all
operating and safety instructions before using the
product. Only use the product as described and
for the stated purpose. If the product is passed on
to a third party, please provide all documents to
the third party together with the product.
Symbols used
The following symbols and key words are used
in this operating manual, on the drill or on the
packaging.
WARNING!
Indicates a hazard that, if not avoided, could
result in death or serious injury.
CAUTION!
Signals a hazard that can cause injuries when
ignored.
NOTE!
Warns against possible damages.
The model name on the drill is a combination of
letters and numbers:
PNS 300 B2
=
2-Speed Power Drill
Scope of delivery
• 2-Speed Power Drill
• Screwing bit, 50 mm
Parts list
Speed selector switch
1
Carbon brushes cover
2
Forward / reverse lever
3
Locking button
4
Handle
5
ON / OFF switch / Speed regulator
6
Torque adjustment ring
7
8
Chuck
9
Chuck unlocking mechanism
10
Torque setting mark
11
Drive spindle with a bit holder
12
Screwing bit, 50 mm
Read the operating manual.
Products marked with this symbol
comply with all applicable
regulations of the European
economic area.
Protection category 2
The „GS“ symbol stands for verified
safety. Products that are marked with
this symbol meet the requirements of the
German product safety law (ProdSG).
2. Technical data
Model number PNS 300 B2
Mains connection 230 V ~ / 50Hz
Rated power 300 W
No-load speed 1. Speed 0 – 400 min
Max drilling
capacity:
Protection class II
2. Speed 0 – 1600 min
Steel max. 10 mm
Wood max. 25 mm
-1
-1
05
Loading...