Parkside PHKSA 12 A1 Translation Of The Original Instructions
CORDLESS CIRCULAR SAW PHKSA 12 A1
CORDLESS CIRCULAR SAW
Translation of the original instructions
AKKU-HANDKREISSÄGE
Originalbetriebsanleitung
IAN 302329
EΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ
ΔΙΣΚΟΠΡΙΟΝΟ ΧΕΙΡΟΣ
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες
της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
GB / IE / NI/CY Translation of t he original instructions Page 1
GR / CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 15
DE / AT / CH Originalbetriebsanleitung Seite 31
A
B
C
Contents
Introduction ......................................................2
Intended use ................................................................ 2
Features ................................................................... 2
Package contents ............................................................ 2
Technical data .............................................................. 2
General power tool safety warnings .................................3
1. Work area safety .......................................................... 3
2. Electrical safety ........................................................... 4
3. Personal safety ............................................................ 4
4. Power tool use and care .................................................... 4
5. Battery tool use and care .................................................... 5
6. Service .................................................................. 5
Appliance-specific safety instructions for circular saws ..................5
Safety guidelines for battery chargers ............................................ 7
Safety information for circular saw blades ......................................... 8
Original accessories/auxiliary equipment ......................................... 8
Before use .......................................................8
Removing/charging/inserting the battery pack ..................................... 8
Checking blade guard functionality .............................................. 8
Operation .......................................................8
Fitting/changing the saw blade ................................................. 8
Rip fence .................................................................. 9
Connecting a dust extraction unit ................................................ 9
Use .............................................................9
Switching on and off .........................................................9
Battery charge level .......................................................... 9
Overload warning ........................................................... 9
Setting the cutting angle ...................................................... 10
Setting the cutting depth ...................................................... 10
Working with the circular saw ................................................. 10
Maintenance and cleaning .........................................10
Disposal ........................................................11
Kompernass Handels GmbH warranty ..............................11
Service .........................................................12
Importer .......................................................12
Translation of the original Conformity Declaration .....................13
PHKSA 12 A1
GB│IE│NI│CY
│
1 ■
Introduction
85 mm
max.26 mm
Congratulations on the purchase of your new appliance. You have chosen a high-quality product. The
operating instructions are part of this product. They
contain important information about safety, usage
and disposal. Before using the product, please
familiarise yourself with all operating and safety
instructions. Use the product only as described and
for the range of applications specified. Please also
pass these operating instructions on to any future
owner.
Intended use
This hand-held circular saw (hereinafter “appliance”) is designed for longitudinal, cross and mitre
cuts in firmly supported chip board, plastics and
lightweight construction materials. Any other uses
of or modifications to the appliance are deemed
to be improper usage and may result in serious
physical injury. Not for commercial use.
Features
Figure A:
Safety lock-out
ON/OFF switch
Release button for battery pack
Battery pack
Cutting depth scale
Locking screw
Base plate
Blade guard
Wing screw for rip fence slot
Spindle lock
Chip ejector
Figure B:
Battery display LED
Overload warning
Vacuum adapter for dust extraction
Cutting angle scale
Wing screw for cutting angle preselector
Rip fence
LED work light
Rip fence slot
Clamping flange
Tensioning screw
Release lever for the blade guard
Saw blade
Hex key
Figure C:
Charging status display LED
Control LED
High-speed charger
Package contents
1 cordless circular saw
1 high-speed battery charger
1 battery pack
1 guide fence
1 vacuum adapter for dust extraction (2 pieces)
1 hex key
1 saw blade (pre-assembled)
1 operating manual
Technical data
Cordless circular saw: PHKSA 12 A1
Rated voltage: 12 V
Rated idle speed: n
Saw blade: 1x Ø 85 mm x 1.1 mm
85 mm
Max. cutting depth: At 0°: 26 mm
Battery pack: PAP 12 A2
Type:
Rated voltage: 12 V
Capacity: 2000 mAh
Cells: 3
(DC)
1400 rpm
0
x Ø 15 mm, 20 teeth
At 45°: approx. 17 mm
LITHIUM ION
(DC)
■ 2 │ GB
│IE│NI│
CY
PHKSA 12 A1
High-speed battery charger: PLG 12 A2
T2A
INPUT:
Rated voltage: 230–240 V~ (AC), 50 Hz
Power consumption: 38 W
OUTPUT:
Rated voltage: 12.6 V
(DC)
Rated current: 2.4 A
Charging time: approx. 60 min
Fuse (internal): 2 A
Protection class: II / (double insulation)
Noise emission value:
Noise measurement value determined in accordance with EN62841. The A-rated noise level of
the power tool is typically as follows:
Sound pressure level: L
Uncertainty K: K
Sound power level: L
Uncertainty K: K
= 83 dB(A)
PA
= 3 dB
PA
= 94 dB(A)
WA
= 3 dB
WA
Wear hearing protection!
WARNING!
► Depending on the manner in which the pow-
er tool is being used, and in particular the
kind of workpiece that is being worked, the
vibration and noise emission values can deviate and may, in many cases, be higher than
the values given in these instructions. Regular
use of the power tool in this way may cause
the user to underestimate the vibration. Try to
keep the vibration loads as low as possible.
Measures to reduce the vibration load are,
e.g. wearing gloves and limiting the working
time. Wherein all states of operation must be
included (e.g. times when the power tool is
switched off and times where the power tool
is switched on but running without load).
General power tool
safety warnings
Vibration emission value:
Total vibration values (vector total of three directions) determined in accordance with EN62841:
Sawing wood a
Uncertainty K = 1.5 m/s
= 2.3 m/s
h,W
2
2
NOTE
► The vibration emission value and noise
emission levels specified in these instructions
have been measured in accordance with the
standardised testing procedure specified and
can be used to make equipment comparisons. The specified vibration emission value
and the noise emission values can also be
used to make an initial load estimate.
PHKSA 12 A1
WARNING!
► Read all safety warnings, instructions, illust-
rations and specifications provided with this
power tool. Failure to follow all instructions
listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future
reference.
The term „power tool“ in the warnings refers to
your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
GB│IE│NI│CY
│
3 ■
2. Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduc-
es the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection.
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites
Protective equipment such
accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles. A careless
action can cause severe injury within a fraction
of a second.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable, from the power tool before making any
adjustments, changing accessories, or storing
power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
■ 4 │ GB
│IE│NI│
CY
PHKSA 12 A1
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking into account the working conditions and
the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in unexpected situations.
5. Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of
fire when used with another battery pack.
b) Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejec-
ted from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
PHKSA 12 A1
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire
or temperature above 130 °C (265°F) may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instructions. Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries!
Protect the rechargeable battery from
heat, for example from continuous
exposure to sunlight, fire, water and
moisture. There is a risk of explosion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement parts. This will ensure that the safety of
the power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by
the manufacturer or authorized service providers.
Appliance-specific safety instructions
for circular saws
Safety instructions for all saws
Sawing method
a) DANGER! Keep your hands clear of
the sawing area and the saw blade.
When both hands are being used to
hold the saw, neither can be injured by the saw
blade.
b) Do not reach underneath the workpiece. The
blade guard cannot protect you from the saw
blade underneath the workpiece.
GB│IE│NI│CY
│
5 ■
c) Set the cutting depth to match the thickness
of the workpiece. The blade should not extend
more than one full tooth depth under the workpiece.
d) Never hold the workpiece to be sawn in your
hand or over your leg. Fasten the workpiece
onto a stable working surface. It is important
to fasten the workpiece securely to minimise the
danger of bodily contact, jamming of the saw
blade or loss of control.
e) Hold the power tool only by the insulated
handles when you are carrying out work
in which the accessory tool may come into
contact with concealed power cables. Contact
with a live wire will also make exposed metal
parts of the power tool live and could give the
operator an electric shock.
f) When making longitudinal cuts, always use
a rip fence or a straight edge guide. This will
improve the accuracy of your cut and reduce
the likelihood of the saw blade jamming.
g) Always use saw blades of the correct size
and with an appropriate central fixing bore
(e.g. diamond-shaped or circular). Blades that
do not match the mounting hardware of the saw
will run eccentrically, causing loss of control.
h) Never use damaged or incorrect blade
washers or bolts. The saw blade washers and
screws have been specially designed to provide
optimum performance and operational safety
for your saw.
Further safety instructions for all saws
Kickback – causes and corresponding safety
instructions
▯ A kickback is a sudden reaction caused as a
result of the saw blade catching, jamming or
being falsely aligned, causing the saw to jump
up uncontrollably and out of the workpiece in
the direction of the operator;
▯ if the saw blade catches or jams in a narrowing
saw cut, the blade can no longer rotate and the
power of the motor throws the appliance back
in the direction of the operator;
▯ if the saw blade twists in the saw cut or be-
comes misaligned, the teeth at the rear edge of
the saw blade can become caught in the wood
surface, causing the saw blade to jump out of
the cut and the saw to jump backwards in the
direction of the operator.
Kickback is a result of saw misuse and/or incorrect
operating procedures or conditions. This can be
avoided by taking proper precautions as given
below.
a) Hold the saw firmly and position your arms
so that they can absorb the force of a kickback. Always stand to the side of the saw
blade and never in line with it. If a kickback
occurs, the circular saw may jump backwards.
However, by taking appropriate precautions the
operator can control the kickback forces.
b) If the saw blade jams or you stop working,
switch the saw off and hold it steadily in the
workpiece until the saw blade has completely
stopped turning. Never attempt to remove
the saw from the workpiece or pull it backwards while the saw blade is still moving as
this could lead to a kickback. Investigate and
take corrective actions to eliminate the cause of
blade binding.
c) If you want to restart a saw that is still in the
workpiece, centre the saw blade in the cut
and check to ensure that the teeth are not
caught anywhere in the workpiece. If the saw
blade catches it can jump out of the workpiece
or cause a kickback when the saw is restarted.
d) Support large panels to minimise the risk of
blade pinching and kickback. Large panels
tend to bend under their own weight. Panels/
boards must be supported on both sides: i.e.
both in the vicinity of the saw cut and also at
the edge.
e) Do not use blunt or damaged saw blades.
Saw blades with blunt or misaligned teeth may
cause excessive friction as the saw cut is too
narrow, and this can cause a saw blade jam
and kickback.
f) Before sawing, ensure that the fastenings for
the cut depth and cut angle settings are tightened. If the settings change while sawing, the
■ 6 │ GB
│IE│NI│
CY
PHKSA 12 A1
saw blade might jam and cause a kickback.
g) Be particularly careful when sawing in exist-
ing walls or other obscured areas. The inserted
saw blade could get caught on hidden objects
and cause a kickback.
Function of the lower blade guard
a) Check whether the lower blade guard closes
properly before each use. Do not operate
the saw if lower blade guard does not move
freely and close instantly. Never clamp or tie
the lower blade guard into the open position.
If the saw is accidentally dropped, lower blade
guard may be bent. Raise the blade guard with
the release lever and make sure it moves freely
and does not touch the blade or any other part
at all angles and cut depths.
b) Check the operation of the lower blade
guard spring. Have the saw serviced before
using it if the lower blade guard and spring
are not working properly. Damaged parts,
sticky deposits or accumulations of chippings
can cause the lower blade guard to operate
slowly.
c) Lower guard may be retracted manually
only for special cuts such as “plunge cuts”
and “compound cuts”. Raise the lower blade
guard with the release lever and release it
as soon as blade enters the material. During
all other types of sawing work, the lower blade
guard should function automatically.
d) Always ensure that the lower blade guard is
covering the blade before placing the saw
down on the workbench or floor. An unpro-
tected, coasting saw blade will move the saw
in the opposite direction to the cutting direction
and saw anything in its path. Always take into
account that the saw blade takes some time to
stop spinning.
Safety guidelines for battery
chargers
■ This appliance may be used by chil-
dren aged 8 years and above and
by persons with limited physical,
sensory or mental capabilities or
lack of experience and knowledge,
provided that they are under supervision or have been told how to use
the appliance safely and are aware
of the potential risks. Do not allow
children to use the appliance as a
toy. Cleaning and user maintenance
tasks must not be carried out by
children unless they are supervised.
■ To avoid potential risks, damaged
mains cables should be replaced
by the manufacturer, their customer
service department or a similarly
qualified person.
The charger is suitable for indoor use only.
WARNING!
■ Do not operate the appliance with a dam-
aged cable, power cord or mains plug. A
damaged power cable poses a threat of a
fatal electric shock.
Supplementary notes:
■ Do not use any grinding discs.
■ Use only saw blades with diameters corre-
sponding to the label on the saw.
■ Always use the right saw blade for the material
being worked.
■ Use only saw blades with a speed marking
that corresponds to or is higher than the speed
specified for the power tool.
■ Saw blades that are intended for use on wood
or similar materials must comply with EN 847-1.
PHKSA 12 A1
GB│IE│NI│CY
│
7 ■
■ Do not allow the teeth of the saw blade to
overheat.
■ When sawing plastic, avoid melting the plastic.
■ Wear a dust mask when sawing.
■ Only use recommended saw blades.
■ Always wear hearing protection!
Safety information for circular saw
blades
Wear protective gloves!
Wear a dust mask!
Wear protective goggles!
Wear hearing protection!
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries.
Original accessories/auxiliary
equipment
■ Only use the accessories and additional
equipment that are specified in the operating instructions and compatible with the
appliance.
Before use
Removing/charging/inserting the
battery pack
CAUTION!
► Always unplug the appliance before you
remove the battery pack
the battery pack to the charger.
from or connect
NOTE
► The battery is supplied partially charged.
Before first use, charge the battery in the
charger for at least 1 hour. This guarantees
full battery performance. You can charge the
lithium-ion battery at any time without shortening its service life. Interrupting the charging
process does not damage the battery.
► If the battery overheats during operation, it
cannot be charged immediately. Allow it to
cool down first.
■ Never charge the battery pack
ambient temperature is below 10°C or above
40°C.
1. To remove the battery pack
button and pull the battery pack out of the
appliance.
2. Insert the battery pack
charger .
3. Insert the mains plug into the socket. The control
lights up red.
LED
4. The green charge status indicator LED
that the charging process is complete and the
battery pack is ready.
5. Insert the battery pack
into the high-speed
back into the appliance.
if the
, press the release
indicates
Checking blade guard functionality
♦ Pull the release lever for the blade guard as
far as it will go.
The blade guard
When letting go of the release lever for the blade
guard , it should automatically jump back to its
original position.
should move without jamming.
Operation
Fitting/changing the saw blade
Always remove the battery pack before changing
the saw blade !
1. Set the cutting depth (using the locking screw
to the minimum position, 0 mm.
2. Swing the blade guard
release lever and put the appliance down.
3. Press the spindle lock button
es) and hold it in.
back using the
(until it engag-
)
■ 8 │ GB
│IE│NI│
CY
PHKSA 12 A1
4. Undo the tensioning screw using a hex key .
5. Now, remove the tensioning screw
clamping flange (see also fig. A).
Fig. A: Changing the saw blade
6. Pull the blade guard
the release lever
in this position.
7. Remove the saw blade
appliance from below.
5. Fitting a saw blade
order.
6. Press the spindle lock button
and use the hex key to tighten the clamping
screw .
all the way back using
and keep the blade guard
carefully out of the
is done in the reverse
and the
(until it engages)
Fig. B: Cutting width 2 cm
♦ Retighten the wing screw for the rip fence .
Connecting a dust extraction unit
♦ Attach the adapter for dust extraction to the
chip ejector
Optional depending on the diameter of the dust
and sawdust extraction.
♦ Connect an approved dust and chip extraction
device.
NOTE
► When sawing wood or other materials that
create dusts that are hazardous to health,
always connect the appliance to a suitable,
certified suction appliance.
.
WARNING!
► The arrow on the saw blade
spond to the arrow showing the direction of
rotation (running direction shown on the
blade guard ).
■ Ensure that the saw blade
rotational speed of the tool.
must corre-
is suitable for the
Rip fence
♦ Undo the wing screw for the rip fence and
place the rip fence in the rip fence slot .
♦ Set the desired cut width
using the scale on the rip fence and the cut
out in the base plate
The right recess in the base plate is for a cutting
angle of 0°. The left recess in the base plate is
for a cutting angle of 45°.
(see also fig. B).
PHKSA 12 A1
Use
Switching on and off
Switching on:
♦ Push the safety lock-out to the left or right
and keep it pressed.
♦ Press the ON/OFF switch . The LED work
light lights up. Once the saw is running, you
can release the safety lock-out .
Switching off:
♦ Release the ON/OFF switch
Battery charge level
♦ The status will be shown on the battery display
LED as follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Overload warning
♦ If the appliance is in danger of overloading,
the overload warning
appliance switches off.
GB│IE│NI│CY
.
lights up briefly. The
│
9 ■
Setting the cutting angle
You can select the cutting angle using the cutting
angle scale .
■ Undo the wing screw
preselector. Set the desired angle on the cutting
angle scale
black metal part (see fig. C). Retighten the wing
screw .
using the top edge of the raised
of the cutting angle
0
Fig. C: Setting the cutting angle to 45 degrees
Setting the cutting depth
NOTE
► Select a cutting depth of approx. 3 mm more
than the thickness of the material. This ensures
that you achieve a clean cut.
♦ Undo the locking screw
cutting depth on the cutting depth scale
using the reference marks (see arrow in fig. D).
Retighten the locking screw .
and set the desired
Maintenance and cleaning
WARNING! RISK OF INJURY! Always
switch the appliance off and remove
the battery before carrying out any
work on the appliance.
The cordless hand-held circular saw is maintenance-free.
■ The appliance must always be kept clean, dry
and free from oil or grease.
■ Never allow liquids to get into the appliance.
■ Use a soft, dry cloth to clean the housing.
Never use petrol, solvents or cleansers which
can damage plastic.
■ The blade guard must always move freely and
close automatically. Therefore, keep the area
around the blade guard clean at all times. Remove dust and chips by blowing them out with
compressed air or with a brush.
■ If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The optimum storage
environment is cool and dry.
NOTE
► Replacement parts not listed (such as batter-
ies, battery charger) can be ordered via our
service hotline.
Fig. D: Setting the cutting depth
Working with the circular saw
1. Switch on the appliance – as described in
“Switching on and off” – and then place it
with the front edge of the base plate
material.
2. Align the machine using the rip fence
using a marked line.
■ 10 │ GB
│IE│NI│
CY
on the
or by
PHKSA 12 A1
Disposal
The packaging is made from environmen-
tally friendly material and can be
disposed of at your local recycling plant.
Do not dispose of power tools in
your normal domestic waste!
European Directive 2012/19/EU requires that
worn-out power tools be collected separately and
recycled in an environmentally compatible manner.
Do not dispose of batteries in your
normal household waste!
Defective or worn-out rechargeable batteries must
be recycled according to Directive 2006/66/EC.
Take the battery pack and/or appliance to a nearby collection facility.
Please consult your local authorities regarding suitable disposal of worn out power tools/battery packs.
Dispose of the packaging in an
environmentally friendly manner.
Note the labelling on the packaging
and separate the packaging material
components for disposal if necessary.
The packaging material is labelled
with abbreviations (a) and numbers
(b) with the following meanings:
1–7: plastics,
20–22: paper and cardboard,
80–98: composites
Your local community or municipal
authorities can provide information on
how to dispose of the product.
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The validity period of the warranty starts from the
date of purchase. Please keep your original receipt
in a safe place. This document will be required as
proof of purchase.
If any material or production fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
at our discretion. This warranty service is dependent
on you presenting the defective appliance and
the proof of purchase (receipt) and a short written
description of the fault and its time of occurrence.
If the defect is covered by the warranty, your product
will either be repaired or replaced by us. The repair
or replacement of a product does not signify the
beginning of a new warranty period.
Warranty period and statutory claims for
defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
PHKSA 12 A1
GB│IE│NI│CY
│
11 ■
Scope of the warranty
This appliance has been manufactured in accordance
with strict quality guidelines and inspected meticulously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product parts
subject to normal wear and tear or fragile parts such
as switches, batteries, baking moulds or parts made
of glass.
The warranty does not apply if the product has been
damaged, improperly used or improperly maintained.
The directions in the operating instructions for the
product regarding proper use of the product are
to be strictly followed. Uses and actions that are
discouraged in the operating instructions or which
are warned against must be avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper handling,
use of force and modifications/repairs which have
not been carried out by one of our authorised
Service centres.
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
■ Please have the till receipt and the item number
(e.g. IAN 12345) available as proof of purchase.
■ You will find the item number on the type plate,
an engraving on the front page of the instructions
(bottom left), or as a sticker on the rear or
bottom of the appliance.
■ If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
■ You can return a defective product to us free of
charge to the service address that will be provided
to you. Ensure that you enclose the proof of
purchase (till receipt) and information about
what the defect is and when it occurred.
Service
WARNING!
► Have the power tool repaired by the service
centre or a qualified electrician and only
using genuine replacement parts. This will
ensure that the safety of the appliance is
maintained.
► Always ensure that the power plug or the
mains cable is replaced only by the manufacturer of the appliance or its customer
service. This will ensure that the safety of the
appliance is maintained.
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
E-Mail: kompernass@lidl.co.uk
Service Ireland
Tel.: 1890 930 034
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: kompernass@lidl.ie
CY
Service Cyprus
Tel.: 8009 4409
E-Mail: kompernass@lidl.com.cy
IAN 302329
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
DE - 44867 BOCHUM
GERMANY
www.kompernass.com
You can download these instructions
along with many other manuals,
product videos and software on
www.lidl-service.com.
■ 12 │ GB
│IE│NI│
CY
PHKSA 12 A1
Loading...