Panasonic SCEN-37-P Service manual

Download

Page 1

ORDER NO. MD0703021CE

CD Stereo System

SC-EN37P

Colour

(K)... Black Type

System

SC-EN37P-K

Main Unit: SA-EN37P-K

Speakers: SB-EN37AP-K (L) & SB-EN37P-K (R)

Specifications

n AMPLIFIERSECTION

FTC OUTPUT POWERboth channel driven simultaneousl

10% total harmonic distortion (THD)

1 kHz 2.8 W per channel

RMS OUTPUT POWERboth channel driven simultaneousl

10% total harmonic distortion (THD)

1 kHz 3 W per channel

Outputimpedance

HEADPHONE 16 W to 32 W

MUSIC PORT 12 kW

Phone Jack

Terminal 3.5 mm stereo

Music Port Jack

Terminal 3.5 mm stereo

n TUNER SECTION

Frequencyrange

FM 87.9 MHz to 107.9 MHz (200 kHz)

87.5 MHz to 108.0 MHz (100 kHz)

AM 520 kHz to 1710 kHz (10 kHz)

n CD SECTION

Disc played [8cm (3”) or 12cm (5”)]

(1) CD-Audio (CD-DA)

(2) CD-R/RW (CD-DA, MP3)

(3) MP3

Sampling frequenc

CD 44.1 kHz

MP3 32 kHz, 44.1 kHz, 48 kHz

Bit rate

MP3 32 kbps to 384 kbps

Decoding 16/20/24 bit linear

Pick up

Wavelength 785 nm

Laser power CLASS 1

udioOutput(Disc)

Number ofchannels 2 channel

Frequencyresponse 20 Hz to 20 kHz (+1, -2 dB)

Wow and flutter Below measurement limit

Digital filter 8

D/Aconverte

n GENERA

Power suppl

Power consumption 30 W

Dimension (WxHXD) 220mmx236mmx146 mm

(8 21/32” x 9 9/32” x 5 3/4”)

Mass

With speakers 3.965kg(8.75lbs)

Withoutspeakers 1.75 kg (3.86 lbs)

n SPEAKERSECTION

MASH (1 bit DAC)

C120V,60Hz

Page 2

SC-EN37P

Typ

Speaker(s) 8 cm (5 1/2”) cone type 6 W

Impedance 6 W

Inputpower 3(M

Dimension (WxHxD) 121 mmx236 mmx146 mm

1Way, 1 speaker system

(4 3/4” x 9 9/32” x 5 3/4”)

Power consumption in standbymode:

Notes:

· Specifications are subject to change without notice.

)

· Mass and dimensions are approximate.

CONTENTS

Page Page

10 Service Fixture and Tools

1 Safety Precautions

1.1. General Guidelines

1.2. Caution for fuse replacemen t

1.3. Before repair and adjustment

1.4. Protection Circuitry

1.5. Safety Parts Information

2 Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

3 Precaution of laser diode

4 Handling Precautions For Traverse Unit

5 About Lead Free Solder (PbF)

5.1. Service caution based on legal restrictions

6 Accessories

7 Operation Procedures

7.1. Remote Control Key Buttons Operations

7.2. Main Unit Key Buttons Operations

7.3. Connection

8 Self diagnosis and special mode setting

8.1. Service Mode Summary Table

8.2. Service Mode Table 1

8.3. Error Code Table 1

9 Assembling and Disassembling

9.1. Caution

9.2. Disassembly flow chart

9.3. Main Components & P.C.B. Locations

9.4. Disassembly of rear cabinet

9.5. Disassembly of D-Port P.C.B.

9.6. Disassembly of Panel P.C.B. & LED P.C.B.

9.7. Disassembly of Main P.C.B., Sensor P.C.B. & Tuner

P.C.B.

9.8. Disassembly of Switch P.C.B. & Traverse Unit

9.9. Disassembly of Power Switch P.C.B. & Tact Switch P.C.B.

9.10. Replacement of Traverse Cover

9.11. Disassembly of CD Servo P.C.B.

9.12. Disassembly of Motor Unit & Motor P.C.B.

9.13. Disassembly of CD Block & CD Lid

9.14. Disassembly of Speakers

11 Service Positions

11.1. Check and Repair of CD Servo P.C.B.

11.2. Check and repair of Main P.C.B., Sensor P.C.B., Tuner

P.C.B., Motor P.C.B., D-Port P.C.B., Panel P.C.B., LED

P.C.B., Power Switch P.C.B., Tact Switch P.C.B. & Switch

P.C.B. 31

12 Voltage and Waveform Chart

12.1. Main P.C.B.

12.2. CD Servo P.C.B.

12.3. Motor P.C.B.

12.4. Panel P.C.B.

12.5. Tuner P.C.B.

12.6. Waveform Chart

13 Wiring Connection Diagram

14 Block Diagram

14.1. CD Servo

14.2. Tuner

14.3. Main (1/2), Transformer, Sensor & D-Port

14.4. Main (2/2), Panel, LED, Power Switch, Tact Switch, Switch

& Motor

15 Notes of Schematic Diagrams

16 Schematic Diagram

16.1. (A) CD Servo Circuit

16.2. (B) Tuner Circuit

16.3. (C) Main Circuit

16.4. (D) Panel Circuit & (E) D-Port Circuit

16.5. (F) LED Circuit, (G) Power Switch Circuit, (H) Tact Switch

Circuit & (I) Switch Circuit

16.6. (J) Motor Circuit, (K) Sensor Circuit & (L) Transformer

Circuit

17 Printed Circuit Board

17.1. (A) CD Servo P.C.B. & (B) Tuner P.C.B.

17.2. (C) Main P.C.B.

17.3. (D) Panel P.C.B., (E) D-Port P.C.B., (F) LCD P.C.B., (G)

Power Switch P.C.B. & (H) Tact Switch P.C.B.

17.4. (I) Switch Circuit P.C.B., (J) Motor Circuit P.C.B., (K)

Sensor Circuit P.C.B. & (L) Transforme r P.C.B.

2.0 W (appx.)

Page 3

18 Illustration of ICs, Transistors and Diodes 59

19 Terminal Function of IC's

19.1. IC801 (MN101EF16ZXW) Servo Processor,Digital Signal

Processor/Digital filter and D/A Converter

20 Exploded Views

20.1. Cabinet Parts Location

20.2. Packaging

21 Replaceme nt Parts List

SC-EN37P

Page 4

SC-EN37P

1 Safety Precautions

1.1. General Guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.

2. After servicing, ensure that all the protective devices such as insulation barriers and insulation papers shields are properly installed.

3. After servicing, check for leakage current checks to prevent from being exposed to shock hazards.

(This “Safety Precaution” is applied only in U.S.A.)

1. Before servicing, unplug the power cord to prevent an electric shock.

2. When replacing parts, use only manufacturer’s recommended components for safety.

3. Check the condition of the power cord. Replace if wear or damage is evident.

4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.

5. Before returning the serviced equipment to the customer, be sure to make the following insulation resistance test to prevent the customer from being exposed to a shock hazard.

1.1.1. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Using an ohmmeter measure the resistance value, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1MW and 5.2MW . When the exposed metal does not have a return path to the chassis, the reading must be

1.1.2. Leakage Current Hot Check (See Figure 1)

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a 1.5kW , 10 watts resistor, in parallel with a 0.15µF capacitor, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.

6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. Should the measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

Fig. 1

Page 5

1.2. Caution for fuse replacement

1.3. Before repair and adjustment

Disconnect AC power, discharge Power Capacitors C611 and C616 through a 10W , 1W resistor to ground.

DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.

After repairs are completed, restore power gradually using a variac, to avoid overcurrent.

Current consum ption at AC 120V, 60 Hz in NO SIGNAL mode (volume min at CD mode) should be ~ 135mA.

1.4. Protection Circuitry

The protection circuitry may have operated if either of the following conditions are noticed:

· No sound is heard when the power is turned on.

· Sound stops during a performance.

The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connec tion wires are

“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.

If this occurs, follow the procedure outlines below:

1. Turn off the power.

2. Determine the cause of the problem and correct it.

3. Turn on the power once again after one minute.

Note :

When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.

SC-EN37P

1.5. Safety Parts Information

Safety Parts List:

There are special components used in this equipment which are important for safety. These parts are marked by should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of manufacturer.

Reference No. Part No. Part Name & Description Remarks

A2 K2CB2CB00018 AC CORD [M]

F901 K5D202APA008 FUSE [M] IP601 K5G302AA0002 FUSE PROTECTOR [M] IP602 K5G251A00008 FUSE PROTECTOR [M]

JK901 K2AB2B000007 FUSE [M]

L901 ELF15N035AN LINE FILTER [M]

T901 G4C5ABD00006 TRANSFORMER [M]

in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts

Table 1

Page 6

SC-EN37P

2 Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equiped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a comme rcially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equiped with ES devices, place the assembly on a conductive surface such as aluminium foil, to prevent electrostatic charge build up or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder remover device. Some solder removal devices not classified as “anti-static (ESD protected)” can generate electrical charge to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize body motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).

Page 7

3 Precaution of laser diode

CAUTION:

This unit utilizes a class 1 laser diode in the optical pickup unit .

Invisible laser radiation is emitted from the optical pickup lens.

Wavelength: 780nm

When the unit is turned on:

1. Do not look directly into the optical pickup lens.

2. Do not use optical instruments to look at the optical pickup lens.

3. Do not adjust the preset variable resistor on the optical pickup lens.

4. Do not disassemble the optical optical pickup unit.

5. If the optical pickup is replaced, use the manufacturer’s specified replacement pickup only.

6. Use of control or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

n Use of caution label (Except for U.S.A.)

SC-EN37P

4 Handling Precautions For Traverse Unit

The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by the static electricity of clothes or our human body.

So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).

· Way of handling the traverse deck (optical pickup)

1. Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock.

2. To prevent the breakdown of the laser diode, an antistatic shorting pin is inserted into the flexible board (FFC board). (Fig. 1)

3. Take care not to apply excessive stress to the flexible board (FFC board). When removing or connecting the short pin, finish the job in as short time as possible.

4. Do not turn the variable resistor (laser power adjustment). It has already been adjusted.

Grounding for electrostatic breakdown prevention

1. Human body grounding. (Fig. 2)

Use the anti-static wrist strap to discharge the static electricity from your body.

2. Work table grounding. (Fig. 2)

Put a conductive material (sheet) or steel sheet on the area where the traverse deck (optical pickup) is place, and ground the sheet.

Page 8

SC-EN37P

Caution :

The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the traverse deck (optical pickup).

Caution when replacing the Traverse Deck

The traverse deck has a short point shorted with solder to protect the laser diode against electrostatics breakdown. Be sure to remove the solder from the short point before making connections.

Page 9

5 About Lead Free Solder (PbF)

5.1. Service caution based on legal restrictions

5.1.1. General description about Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that of the normal solder.

Definition of PCB Lead Free Solder being used

The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder. (See right figure)

Service caution for repair work using Lead Free Solder (PbF)

· The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

· To put lead free solder, it should be well molten and mixed with the original lead free solder.

· Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

· Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt

the lead free solder.

· Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30

degrees C (662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

· The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01K-----------(0.3mm 100g Reel)

RFKZ06D01K-----------(0.6mm 100g Reel)

RFKZ10D01K-----------(1.0mm 100g Reel)

SC-EN37P

Note

* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

Page 10

SC-EN37P

6 Accessories

Remote Control

AC Cord

FM/AM Antenna

I-Pod cradle

Page 11

7 Operation Procedures

7.1. Remote Control Key Buttons Operations

SC-EN37P

7.2. Main Unit Key Buttons Operations

Page 12

SC-EN37P

7.3. Connection

Page 13

8 Self diagnosis and special mode setting

This unit is equipped with features of self-diagnostic & special mode setting for checking the functions & reliability.

8.1. Service Mode Summary Table

The service mode can be activated by pressing various button combination on the main unit and remote control unit. Below is the summary for the various modes for checking:-

Player buttons Remote control unit buttons Application Note

[ ] [4], [7] To enter into doctor mode for various item

checking.

Mode Remote control unit buttons Application Note

Doctor Mode [DIMMER] FL ALL Segment inspection (Refer to the section 8.2 for more

[7], [8], [9] Forced VOL setting (Refer to the section 8.2 for more

[ ], [1], [1] CD Loading Test (Refer to the section 8.2 for more

[ ], [1], [2] CD Traverse Test (Refer to the section 8.2 for more

[ ], [1], [3] CD Combination Test (Refer to the section 8.2 for more

[ ], [1], [4] CD Auto Adjustment Display (Refer to the section 8.2 for more

[SLEEP] Cold Start setting (Refer to the section 8.2 for more

(Refer to the section 8.2 for more information.)

information.)

SC-EN37P

8.2. Service Mode Table 1

Below is the various special modes for checking:-

Item FL Display Key Operation

Mode Name Description Front Key

Self-Diagnostic Mode

To enter into self diagnostic checking for main unit.

1. Select [CD] for CD mode (Ensure no CD inserted.)

2. Press and hold [ seconds follow by [FF]

To exit, press [ main unit or remote control.

] button for 2

] button on

Page 14

SC-EN37P

Item FL Display Key Operation

Mode Name Description Front Key

Doctor Mode To enter into Doctor Mode for

checking of various items and displaying EEPROM and firmware version. Note: The micro-processor version as shown is an example. It will be revise when there is an updates. FL Display sequence Display 1 ﬁ 2

DIsplay 1

Checksum (Condition 1) When EEPROM IC detected and has ROM correction.

Checksum (Condition 2) When EEPROM IC is detected and there is no ROM correction.

In any mode:

1. Press [

] button on main unit follow by [4] and [7] on remote control.

To exit, press [

] button on

main unit or remote control.

FL Display Test To check the FL segments display (All

segments will light up)

Checksum (Condition 3) When EEPROM IC is detected and has ROM correction but not working properly.

Display 2

The Check Sum of EEPROM and firmware version will be display for 1 sec. * ROM correction ** Firmware version No:

In doctor mode:

1. Press [DIMMER] button on remote control.

To exit, press [

] button on

main unit or remote control.

Page 15

Item FL Display Key Operation

Mode Name Description Front Key

Volume Setting Mode

To check for the volume setting of the main unit. The volume will be automatically set to its respective level (in dB). During the mode, trebble/bass/EQ will be set to “0” dB & OFF.

In doctor mode:

1. Press [7] button on remote control.

2. Press [8] button on remote control.

SC-EN37P

CD Loading Test Mode

CD Traverse Unit Test Mode

CD Combination Test Mode

To determine the reliability of CD Loading unit. To check for the Open/Close operation for the CD loading unit. It fails when there is abnormality in opening or closing.

To check for the traverse unit operation. In this mode, the first & last track is access & read. (TOC). It fails when TOC is not completed by IOS or the traverse is out of focus.

A combination of CD loading & traverse unit test.

The counter will increment by 1 until reach

9999999

ﬂ

The counter will increment by 1 until reach

9999999

ﬂ

The counter will increment by 1 until reach

9999999

ﬂ

3. Press [7] button on remote control. To exit, press [ main unit or remote control.

In doctor mode:

1. Press [ remote control.

To cancel, press [0] button remote control. To exit, press [ main unit or remote control.

In doctor mode:

1. Press [ remote control.

To cancel, press [0] button remote control. To exit, press [ main unit or remote control.

In doctor mode:

1. Press [ remote control.

To cancel, press [0] button remote control. To exit, press [ main unit or remote control.

], [1] & [1] button on

], [1] & [2] button on

], [1] & [3] button on

] button on

CD Auto Adjustment Display

Cold Start To activate cold start upon next AC

To display result of self adjustment for CD. For more information, please refer to Section 8.2.1.

The [NO DISC] display will appear after 3s,

power up.

8.2.1. CD Self-Adjustment (AJST) Result Display

Purpose: To display result of self-adjustment for CD.

In doctor mode:

1. Press [ remote control.

To cancel, press [0] button remote control. To exit, press [ main unit or remote control.

In doctor mode:

1. Press [SLEEP] button on remote control.

To exit, press [

ﬂ

main unit or remote control.

], [1] & [4] button on

] button on

Page 16

SC-EN37P

Below is the procedures for this mode.

Step 1: Enter into Doctor mode (For more information refer to section 8.2 on key operation to enter into this mode).

Step 2: When [

], [1] & [4] are pressed at the doctor mode, the following shall be displayed for 3s. The result shall correspond

to the condition met as shown in the table below:

8.3. Error Code Table 1

8.3.1. Mechanism Error Code Table

Self-Diagnosis Function provides information on any problems occuring for the unit and its respective components by displaying error codes. These error code such as U**, H** and F** are stored in memory and held unless it is cleared.

The error code is automatically display after entering into self-diagnostic mode.

Error Code Diagnosis Contents Description of error Automatic FL Display Remarks

F15 CD REST SW

abnormal

F26 Communication

between CD servo LSI and micro-p abnormal.

F76 Abnormality in the

output voltage of stabilized power supply.

CD traverse position initial setting operation failsafe counter (1000ms) waiting for REST SW to turn on. Error no. shall be clear by force or during cold start.

CD function DTMS command, after system setting, if SENSE = “L” cannot be detected. Memory shall contain F26code. After power on, CD function shall continue, error display shall be “NO DISC”. Error no. shall be clear by force or cold start.

In normal operation when “DCDET” is detected “L” (IOIO) for two consecutive times, this error code will be displayed for 2s & after PCONT will be turned to “L” (Low).

For CD unit.(For traverse). Press [

Press [ ] on main unit for next error.

] on main unit for next error.

Page 17

9 Assembling and Disassembling

9.1. Caution

“ATTENTION SERVICER”

Some chassis components may have sharp edges. Be careful when disassembling and servicing.

1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components.

2. For reassembly after operation checks or replacement, reverse the respective procedures. Special reassembly procedures are described only when required.

3. Select items from the following index when checks or replacement are required.

4. Refer to the Parts No. on the page of “Parts Locatio n and Replacement Parts List” (Section 21), if necessary.

Warning :-

This product uses a laser diode. Refer to caution statement Precaution of Laser Diode.

Below is the list of disassembly sections

· Disasse mbly of Rear Cabinet

· Disasse mbly of D-Port P.C.B.

· Disasse mbly of Panel P.C.B. & LCD P.C.B.

· Disasse mbly of Main P.C.B., Sensor P.C.B., Tuner P.C.B.

· Disasse mbly of CD Servo P.C.B. & Switch P.C.B.

· Disasse mbly of Power Switch P.C.B. & Tact Switch P.C.B.

· Replacement of Traverse Cover

· Disasse mbly of CD Servo P.C.B.

· Disasse mbly of Motor Unit & Motor P.C.B.

· Disasse mbly of CD Block & CD Lid

· Disasse mbly of Speaker

Below shown is part no. of different screws types used:

SC-EN37P

Page 18

SC-EN37P

9.2. Disassembly flow chart

The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing.

To assemble the unit, reverse the steps shown in the chart as below.

9.2.1. For Main unit

9.2.2. For Speaker unit

Page 19

9.3. Main Components & P.C.B. Locations

9.3.1. Main Parts Locations

SC-EN37P

9.3.2. Speaker Unit Parts Location (For SB-EN37A only)

Page 20

SC-EN37P

9.4. Disassembly of rear cabinet

Step 1 Remove 10 screws.

9.5. Disassembly of D-Port P.C.B.

Step 2 Lift up the rear cabinet.

Step 3 Detach cable (FP806) on Main P.C.B. and remove the

rear cabinet as arrow shown.

· Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet

Step 1 Remove 2 screws.

Step 2 Remove D-Port P.C.B..

9.6. Disassembly of Panel P.C.B. & LED P.C.B.

· Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet

Step 1 Remove 2 screws on the LCD Holder unit.

Page 21

Step 2 Detach cable (P801).

9.7. Disassembly of Main P.C.B., Sensor P.C.B. & Tuner P.C.B.

· Follow the (Step 1) - (Step 2) of Item 9.4 - Disassembly of rear cabinet

Step 1 Remove 5 screws.

Step 2 Detach cables (P352, P351 ,FP701 ,P801 & P802) on

Main P.C.B. .

Step 3 Lift up the Main P.C.B. Sensor P.C.B. and Tuner P.C.B.

SC-EN37P

9.8. Disassembly of Switch P.C.B. & Traverse Unit

· Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet

· Follow the (Step 1) - (Step 3) of Item 9.7 - Disassembly of Main P.C.B., Sensor P.C.B. & Tuner P.C.B.

Step 1 Remove 4 screws.

Step 2 Remove 2 screws on Switch P.C.B..

Page 22

SC-EN37P

9.9. Disassembly of Power Switch P.C.B. & Tact Switch P.C.B.

· Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet

· Follow the (Step 1) - (Step 2) of Item 9.6 - Disassembly of Panel P.C.B. & LED P.C.B.

Step 1 Detach cable (P802) on Main P.C.B.

Step 2 Remove 3 screws.

Step 3 Release 1 claw to remove front ornament.

Step 4 Release 6 catches to remove Power P.C.B. & Tact

Switch P.C.B..

· Assemble of Front Ornament into slot.

Ensure front ornament fully insert to front cabinet.

9.10. Replacement of Traverse Cover

· Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet

· Follow the (Step 1) - (Step 2) of Item 9.7 - Disassembly of Main P.C.B. , Sensor P.C.B. & Tuner P.C.B.

· Follow the (Step 1) of Item 9.8 - Disassembly of Switch P.C.B. & Traverse Unit

Page 23

Step 1 Release 3 catches and remove the Traverse Cover.

Step 2 Pull out FFC.

SC-EN37P

Step 3 Widening the catch, push the fixed pin in. (a) ﬁ (b)

Step 4 Lift up the traverse unit to remove it.

Caution:

Keep the floating springs (x 4) in safe place & avoid losing them.

9.11. Disassembly of CD Servo P.C.B.

· Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet

· Follow the (Step 1) - (Step 2) of Item 9.7 - Disassembly of Main P.C.B. , Sensor P.C.B. & Tuner P.C.B.

· Follow the (Step 1) of Item 9.8 - Disassembly of Switch P.C.B. & Traverse Unit

· Follow the (Step 1) - (Step 4) of Item 9.9 - Disassembly of Power Switch P.C.B. & Tact Switch P.C.B.

Step 1 Desolder the terminal.

Page 24

SC-EN37P

Step 2 Remove 3 screws.

Step 3 Flip the CD Servo P.C.B. over to one side.

Step 4 Detach FFC out from the connector.

Step 5 Attach a short pin to the unit.

Caution:

Insert a short pin into FFC of the optical pickup. [See “Handling Precautions for traverse unit”].

9.12. Disassembly of Motor Unit & Motor P.C.B.

· Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet

· Follow the (Step 1) - (Step 2) of Item 9.7 - Disassembly of Main P.C.B. , Sensor P.C.B. & Tuner P.C.B.

Step 1 Remove 2 screws.

Step 4 Remove the belt.

Step 5 Remove pulley gear, 2nd gear and drive gear.

· Disassembly of motor assembly (gears & belt)

Step 2 Remove motor assembly.

Step 3 Remove 2 screws.

Step 6 Remove 2 screws at motor unit.

Step 7 Remove 1 screw and unsolder 3 points at gear base.

Page 25

9.13. Disassembly of CD Block & CD Lid

· Follow the (Step 1) - (Step 3) of Item 9.4 - Disassembly of rear cabinet

· Follow the (Step 1) - (Step 2) of Item 9.7 - Disassembly of Main P.C.B. , Sensor P.C.B. & Tuner P.C.B.

· Follow the (Step 2) of Item 9.8 - Disassembly of CD Servo P.C.B. & Switch P.C.B.

· Follow the (Step 1) of Item 9.11 - Disassembly of Motor Unit & Motor P.C.B.

Step 1 Remove 6 screws to remove CD Block Unit.

Step 3 Remove 4 screws, remove sw lever (left) and roller

guide (R).

SC-EN37P

Step 2 Remove 2 screws.

Step 4 Remove cd lid.

Page 26

SC-EN37P

9.14. Disassembly of Speakers

9.14.1. Disassembly of the speaker (SB-EN37) - (R)

Step 1 Remove 6 screws.

Step 2 Remove the back cabinet ass’y..

Step 4 Remove 4 screws.

· Disasse mbly of net frame ass’y

Step 5 Remove 4 screws.

Step 3 Unsolder the lead wires, silver (-) and gold (+).

Page 27

9.14.2. Disassembly of the rear cabinet (SB-EN37A) - (L)

SC-EN37P

Step 1 Remove 6 screws.

Step 2 Remove the back cabinet ass’y..

Step 3 Unsolder the lead wires.

Step 4 Remove 4 screws.

Page 28

SC-EN37P

· Disasse mbly of net frame ass’y

Step 5 Remove 4 screws.

Step 1 Remove 1 screw on back cabinet assy.

Step 2 Remove 3 screws to remove the port unit.

Step 3 Remove 4 screws on Transformer P.C.B. unit.

Step 4 Unsolder wire and remove Transformer P.C.B..

· Removal of Transformer P.C.B.

Page 29

10 Service Fixture and Tools

Service Tools

Extension FFC (A) CD Servo P.C.B. - Main P.C.B. REEX0485 (14 Pins)

11 Service Positions

General procedures:

Connect the DC in cord cable from (SB-EN37A) to main set, connect AC power supply cord to speaker to on the set. Load in cd and switch off the set. Proceed to checking.

Note: For description of the disassembly procedures, see the Section 9.

SC-EN37P

Page 30

SC-EN37P

11.1. Check and Repair of CD Servo P.C.B.

Page 31

11.2. Check and repair of Main P.C.B., Sensor P.C.B., Tuner P.C.B., Motor

P.C.B., D-Port P.C.B., Panel P.C.B., LED P.C.B., Power Switch P.C.B., Tact Switch P.C.B. & Switch P.C.B.

SC-EN37P

Page 32

SC-EN37P

12 Voltage and Waveform Chart

Note:

Circuit voltage and waveform described herein shall be regarded as reference inform ation when probing defect point, because it may differ from an actual measuring value due to difference of Measuring instrument and its measuring condition and product itself.

12.1. Main P.C.B.

Page 33

12.2. CD Servo P.C.B.

SC-EN37P

12.3. Motor P.C.B.

12.4. Panel P.C.B.

12.5. Tuner P.C.B.

Page 34

SC-EN37P

12.6. Waveform Chart

Page 35

13 Wiring Connection Diagram

SC-EN37P

Page 36

SC-EN37P

Page 37

14 Block Diagram

14.1. CD Servo

SC-EN37P

Page 38

SC-EN37P

14.2. Tuner

Page 39

14.3. Main (1/2), Transformer, Sensor & D-Port

SC-EN37P

Page 40

SC-EN37P

14.4. Main (2/2), Panel, LED, Power Switch, Tact Switch, Switch & Motor

Page 41

15 Notes of Schematic Diagrams

(All schematic diagrams may be modified at any time with the development of the new technology)

S351 : CD TOP Switch S352 : CD BOTTOM Switch S801 : POWE R Switch ( S802 : VOL - Switch ( S803 : VOL + Switch ( S804 : REV_SKIP Switch ( S805 : FWD_SKIP Switch ( S806 : TUNER/XM Switch S807 : CD Switch ( S808 : MUSIC_PORT Switch (FM/AM/MUSIC

PORT)

S809 : STOP Switch ( S810 : CD_OP/CL Switch ( S7201 : REST Switch

· Importance safety notice :

Components identified by characteristics important for safety. Furthermore, special parts which have purposes of fireretardant (resistors), high-quality sound (capacitors), lownoise (resistors), etc. are used.

When replacing any of components, be sure to use only

manufacturer´s specified parts shown in the parts list.

· Capacitor values are in microfarad(µF) unless specified otherwise, F=Farad, pF=Pico-Farad

Resistance values are in ohm(W ), unless specified otherwise, 1K=1,000W , 1M=1,000KW

)

mark have special

)

) )

)

SC-EN37P

· Voltage and Signal lines:

: +B Signal line

: -B Signal line

: CD-DA signal line

: CD signal line

: Main signal line

: FM/AM signal line

: AM signal line

: FM signal line

: AUX signal line

Page 42

SC-EN37P

Page 43

16 Schematic Diagram

(All schematic diagrams may be modified at any time with the development of the new technology)

SC-EN37P

Page 44

SC-EN37P

16.1. (A) CD Servo Circuit

Page 45

16.2. (B) Tuner Circuit

SC-EN37P

Page 46

SC-EN37P

16.3. (C) Main Circuit

Page 47

SC-EN37P

Page 48

SC-EN37P

Page 49

16.4. (D) Panel Circuit & (E) D-Port Circuit

SC-EN37P

Page 50

SC-EN37P

16.5. (F) LED Circuit, (G) Power Switch Circuit, (H) Tact Switch Circuit & (I) Switch Circuit

Page 51

16.6. (J) Motor Circuit, (K) Sensor Circuit & (L) Transformer Circuit

SC-EN37P

Page 52

SC-EN37P

Page 53

17 Printed Circuit Board

Note: Circuit board diagrams may be modified at any time with the development of new technology.

17.1. (A) CD Servo P.C.B. & (B) Tuner P.C.B.

SC-EN37P

Page 54

SC-EN37P

17.2. (C) Main P.C.B.

Page 55

17.3. (D) Panel P.C.B., (E) D-Port P.C.B., (F) LCD P.C.B., (G) Power Switch P.C.B. & (H) Tact Switch P.C.B.

SC-EN37P

Page 56

SC-EN37P

17.4. (I) Switch Circuit P.C.B., (J) Motor Circuit P.C.B., (K) Sensor Circuit P.C.B. & (L) Transformer P.C.B.

Page 57

17.4. (I) Switch Circuit P.C.B., (J) Motor Circuit P.C.B., (K) Sensor Circuit P.C.B. & (L) Transformer P.C.B.

SC-EN37P

Page 58

SC-EN37P

Page 59

18 Illustration of ICs, Transistors and Diodes

SC-EN37P

Page 60

SC-EN37P

19 Terminal Function of IC's

19.1. IC801 (MN101EF16ZXW) Servo Processor,Digital Signal Processor/Digital filter and D/A Converter

Pin No. Mark I/O Function

1 PCONT1 O Power Control Output

(PWR Sply Active HIGH) 2 DPORT_PCONT O 5.3V Regulator Control 3 N.C. - No connection 4 LCD_DI O LCD Data Output 5 LCD_CE O LCD chip select 6 LCD_CLK O LCD CLK Output 7 LCD_INH O LCD lighting terminal 8 XM MUTE - No Connection 9 I2S_RATE - No Connection 10 LINKACTIVE - No Connection 11 GND I Memory mode selection 12 OSC2 (OUT) O Main Oscillator output

(8MHz) 13 OSC1 (In) I Main Oscillator input

(8MHz) 14 VSS - Micom GND 15 XI I Slow Oscillator input

(32KHz) 16 XO O Slow Oscillator output

(32KHz) 17 VDD33 - 3.3V 18 VDD18 - Connect to pin 37 19 NRST I MICOM RESET IN (L:

reset) 20 DAC RESET - No Connection 21 ANT_REV - No Connection 22 XM_RST - No Conenction 23 XM_PCONT - No Connection 24 N.C. - No connection 25 RMT I Remote Control Input 26 N.C. - No connection 27 D_DOWFIC I DAB LSI 24ms

synchronization interrupt 28 DAB_IRQ - No Connection 29 BLKCK I CD Subcode Block Clock

Input 30 VCCDET I VCC failure detect (Active

low) 31 MDATA O CD LSI Command Data 32 STATUS I CD LSI Status Input 33 CD_MCLK O CD LSI Command Clock 34 USB_SDA - No Conenction 35 USB_RST - No Connection 36 USB_SCL - No Connection 37 VDD18 - Power supply (1.8V) 38 USB_REQ - No Connection 39 VCC - Micon GND 40 ASP_CLK O ASP Sound Processor

Serial Clock Output 41 ASP_DATA O APC Sound Processor

Serial Data Output 42 MLD O CD LSI command load 43 RESET_SW I Reset SW (L: Inner) 44 CD_RST O CD LSI Reset Output (L:

reset) 45 MUTE_A O Analog Mute Output (L:

Mute on) 46 CD_BOTTOM_SW I CD bottom switch 47 CD_TOP_SW I CD top switch 48 N.C. - No connection 49 N.C. - No connection 50 PLL_DO O PLL Data Output

Pin No. Mark I/O Function

51 PLL_DI O PLL Data Input 52 N.C. - No connection 53 N.C. - No connection 54 N.C. - No connection 55 PLL_CLK O PLL clock 56 PLL_CE O PLL chip select 57 E-CS - No Connection 58 E_DATA I/O EEPROM DATA I/O 59 E_CLK - No Connection 60 MBP1 O Micro-P Beat Proof 1 61 MBP2 O Micro-P Beat Proof 2 62 CRTIMER - CR TIMER 63 VSS - Micon GND 64 FL_RST - No Connection 65 CD_CLOSE O CD Tray Close Control

(Active H)

66 CD_OPEN O CD Tray Open Control

(Active H) 67 DAB_RST - No Connection 68 DAB_TU_RST - No Connection 69 DAB_TU_SCL - No Connection 70 DAB_TU_SDA - No Connection 71 DBA_PCNT - No Connection 72 DBA_RX/XM_TXD - No Connection 73 DAB_TX - No Connection 74 DAB_TX/XM_RXD - No Connection 75 DAB_MODE - No Connection 76 UART_IN I Serial communica tion 77 UART_OUT O Serial communiation 78 D_LINK_DET 1 I Detect connecting unit 79 D_LINK_DET2 I Detect connecting unit 80 IPOD_DET I IPOD detection 81 AD_ACK IN I D-Port charging full

detection 82 AD_RSKIP O Dport AD_CNTL 83 AD_FSKIP O Dport AD_CNTL 84 AD_STOP O Dport AD_CNTL 85 AD_PLAY O Dport AD_CNTL 86 N.C. - No connection 87 N.C. - No connection 88 N.C. - No connection 89 VDD - Micon VDD+3.3V 90 N.C. - No connection 91 VSS - GND 92 KEY1 I Key 1 Input 93 MM0D0 - No Connection 94 TERR - No Connection 95 PDET2 I Level detection for 5.3V

regulator 96 PDET1 I DC Level Detection Input 97 REGION I Region Setting Input 98 N.C. - No connection 99 N.C. - No Connection 100 VREF+ - A/D Converter reference

voltage +3.3V

Page 61

20 Exploded Views

20.1. Cabinet Parts Location

SC-EN37P

Page 62

SC-EN37P

Page 63

20.2. Packaging

SC-EN37P

Page 64

SC-EN37P

Page 65

21 Replacement Parts List

Notes:

· Important safety notice:

Components identified by

Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used.

When replacing any of these components, be sure to use only manufacture r’s specified parts shown in the parts list.

· The parenthesized indications in the Remarks columns specify the areas or colour. (Refer to the cover page for area or colour)

Parts without these indications can be used for all areas.

· W arning: This product uses a laser diode. Refer to caution statements on “Precaution of Laser Diode”.

· Capacitor values are in microfarads (µF) unless specified otherwise, P= Pico-farads (pF), F= Farads.

· Resistance values are in ohms, unless specified otherwise, 1K=1,000 (OHM).

· The marking (RTL) indicates that the Retention Time is limited for this items. After the discontinuation of this assembly in

production, the item will continue to be available for a specific period of time. The retention period of a availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available.

· [M] Indicates in the Remarks columns indicates parts supplied by PAVCSG.

· Reference for O/I book languages are as follows:

Ar: Arabic Du: Dutch It: Italian Sp Spanish Cf: Canadian French En: English Ko: Korean Sw: Swedish Cz: Czech Fr: French Po: Polish Co: Traditional Chinese Da: Danish Ge: German Ru: Russian Cn: Simplified Chinese Pe: Persian Ur: Ukraine

mark have special characteristics important for safety.

SC-EN37P

Ref. No. Part No. Part Name & Description Remarks

CABINET AND CHASSIS

1 RDG0612 PULLEY GEAR [M]

2 RDGV0001 2ND GREAR [M]

3 RDGV0002 DRIVE GEAR [M]

4 RDGV0003 LID GEAR [M]

5 RFKPAEN25PS MOTOR ASS’Y [M]

6 REEV0150 CD SERVO FFC (22P) [M]

7 REEV0180 OPTION PORT FFC [M]

8 RFKLAEN37P-K CD LID ASS’Y (A/B) [M]

8-1 RDPV0001 LID ROLLER [M]

8-2 RMG0699-KJ LID CUSHION [M]

8-3 RHD14136 SCREW [M]

9 RFKGAEN37P-K FRONT PANEL ASS’Y [M]

10 RGKV0165-K FRONT ORNAMENT [M]

11 RGPV0093-K LCD PANEL [M]

12 RGPV0094-K SENSOR PANEL [M]

13 RGUV0173-S POWER BUTTON [M]

14 RGUV0174B-S FUNCTION BUTTON [M]

15 RGUV0175-K VOL/SKIP BUTTON [M]

16 RHD26046-L SCREW [M]

17 RKA0162-KJ LEG RUBBER [M]

18 RKQV0052-K CD BASE [M]

19 RKSV0038G-K REAR CABINET [M]

20 RMAV0042 TRANS ANGLE [M]

21 RMG0268-K1 BELT [M]

22 RMKV0065 ROLLER GUIDE L [M]

23 RFKNAEN37P-K GEAR BASE ASS’Y [M]

24 RMKV0066 ROLLER GUIDE R [M]

25 RMLV0001 SW LEVER [M]

26 RMNV0080 LCD FIX PIECE [M]

27 RMNV0081 DC JACK HOLDER [M]

28 RMNV0082 LCD HOLDER [M]

29 RMNV0083 LED HOLDER [M]

30 RMNV0084 ANT HOLDER [M]

31 RMQV0077 GEAR FIXTURE [M]

32 RMSV0001 LID BEARING [M]

33 RMXV0032 LCD SPACER SHEET [M]

34 RMY0362J IC HEAT SINK [M]

35 RMYV0067 HEAT SINK [M]

Ref. No. Part No. Part Name & Description Remarks

36 RSC0732J EARTH PLATE [M]

37 RSC0733J TUNER SHIELD [M]

38 XTN2+6GFJ SCREW [M]

39 XTV3+12GFJK TOP CAB SCREW [M]

40 XYN26+C6FJ SCREW [M]

SPEAKERS

71 RFKHBEN37PKL SPEAKER CAB. ASS’Y L [M]SB-

71 RFKHBEN37PKR SPEAKER CAB. ASS’Y R [M]SB-

71-1 K2GY2C000001 DC IN CABLE [M]SB-

72 RFAX0011-KJ LEG FELT [M]

73 RKPV0048-K SP FRONT CABINET [M]

74 RYBV0046 PREPARED NET FRAME [M]

75 EAS8P198B SPEAKER [M]

76 RYTV0003 SP PORT UNIT [M]

77 XTV3+12GFJ-M SCREW [M]

78 XTV3+6FFJ SCREW [M]SB-

TRAVERSE DECKS

301 RAE0165T-V TRAVERSE (W/O CD SERVO

302 RMR1396-K TRV COVER [M]

303 RMS0757-1 FIXED PIN [M]

304 RME0109 FLOATING SPRING [M]

305 RMG0730-G FLOATING RUBBER [M]

306 XTN2+6GFJ SCREW [M]

307 RMR1395-X MIDDLE CHASSIS [M]

REPV0111A CD SERVO P.C.B. [M](RTL)

REPV0136A TUNER P.C.B. [M](RTL)

REPV0136A MAIN P.C.B. [M](RTL)

REPV0136A PANEL P.C.B. [M](RTL)

REPV0129A D-PORT P.C.B. [M](RTL)

P.C.B.)

PRINTED CIRCUIT BOARDS

EN37A

EN37

EN37A

[M]

Page 66

SC-EN37P

Ref. No. Part No. Part Name & Description Remarks

IC1 C1BB00001120 IC TUNER [M]

IC301 C1BB00000732 IC AUDIO SOUND PROCESSOR [M]

IC351 C0GAE0000007 IC MOTOR DRIVER [M]

IC601 C0AAAA000036 IC POWER [M]

IC602 C0DAEKG00002 IC REGULATOR [M]

IC801 MN101EF16ZXW IC MICON [M]

IC1001 C0HBA0000238 IC LCD DRIVER [M]

IC3001 C0ABBB000297 IC DUAL OP-AMP [M]

IC3002 C0JBAB000884 IC LOGIC [M]

IC3003 C0CBCBC00090 IC 3.3V LDO [M]

IC7001 MN6627954MA IC SERVO

IC7002 BA5948FPE2 IC 4 CH DRIVE [M]

Q1 B1ABDF000026 TRANSISTOR [M]

Q2 B1ADCF000063 TRANSISTOR [M]

Q301 B1ADCF000063 TRANSISTOR [M]

Q401 B1ABGD000022 TRANSISTOR [M]

Q501 B1ABGD000022 TRANSISTOR [M]

Q601 B1ABDF000026 TRANSISTOR [M]

Q603 B1ACND000003 TRANSISTOR [M]

Q604 B1ABDF000026 TRANSISTOR [M]

Q605 B1BCCG000002 TRANSISTOR [M]

Q606 B1ADCF000063 TRANSISTOR [M]

Q607 B1ABDF000026 TRANSISTOR [M]

Q608 B1ACND000003 TRANSISTOR [M]

Q611 B1ACND000003 TRANSISTOR [M]

Q612 B1ABDF000026 TRANSISTOR [M]

Q613 B1ADCF000063 TRANSISTOR [M]

Q615 B1BAAJ000003 TRANSISTOR [M]

Q617 B1ABDF000026 TRANSISTOR [M]

Q622 B1ACND000003 TRANSISTOR [M]

Q623 B1ABDF000026 TRANSISTOR [M]

Q801 B1ABDF000026 TRANSISTOR [M]

Q802 B1ABDF000026 TRANSISTOR [M]

Q3001 B1ADCE000012 TRANSISTOR [M]

Q3002 B1ABEB000002 TRANSISTOR [M]

Q7601 B1ADCF000001 TRANSISTOR [M]

QR609 UNR521400L TRANSISTOR [M]

QR614 B1GBCFGJ0016 TRANSISTOR [M]

QR618 B1GBCFGJ0016 TRANSISTOR [M]

QR619 B1GBCFGJ0016 TRANSISTOR [M]

QR621 UNR511100L TRANSISTOR [M]

QR803 UNR521300L TRANSISTOR [M]

QR804 UNR511100L TRANSISTOR [M]

QR3001 B1GBCFGN0016 TRANSISTOR [M]

QR3002 B1GBCFGN0016 TRANSISTOR [M]

QR3003 B1GBCFGN0016 TRANSISTOR [M]

QR3004 B1GBCFGN0016 TRANSISTOR [M]

D1 B0CDAD000010 DIODE [M]

D2 B0CDAB000019 DIODE [M]

D3 B0CDAB000019 DIODE [M]

D4 B0AACK000004 DIODE [M]

D602 B0EAKM000117 DIODE [M]

D603 B0EAKM000117 DIODE [M]

D604 B0EAKM000117 DIODE [M]

REPV0136A LED P.C.B. [M](RTL)

REPV0136A POWER SWITCH P.C.B. [M](RTL)

REPV0136A TACT SWITCH P.C.B. [M](RTL)

REPV0136A SWITCH P.C.B. [M](RTL)

REPV0136A MOTOR P.C.B. [M](RTL)

REPV0136A SENSOR P.C.B. [M](RTL)

REPV0136A TRANSFORMER P.C.B [M](RTL)

INTEGRATED CIRCUITS

PROCESSOR/DIGITAL SIGNAL PROCESSOR/DIGITAL FILTER D/A CONVERTER

TRANSISTORS

DIODES

[M]

Ref. No. Part No. Part Name & Description Remarks

D605 B0AACK000004 DIODE [M]

D607 B0AACK000004 DIODE [M]

D608 B0BA8R700009 DIODE [M]

D610 B0AACK000004 DIODE [M]

D611 B0AACK000004 DIODE [M]

D612 B0ACCE000003 DIODE [M]

D613 B0ACCE000003 DIODE [M]

D614 B0BA6R100003 DIODE [M]

D615 B0BA4R600003 DIODE [M]

D616 B0EAKM000117 DIODE [M]

D621 B0AACK000004 DIODE [M]

D622 B0BA5R000004 DIODE [M]

D801 B0AACK000004 DIODE [M]

D802 B0AACK000004 DIODE [M]

D803 B0ACCE000003 DIODE [M]

D901 B0EAMM000038 DIODE [M]

D902 B0EAMM000038 DIODE [M]

D903 B0EAMM000038 DIODE [M]

D904 B0EAMM000038 DIODE [M]

D1001 B0BA7R900004 DIODE [M]

D1005 LNG4A4CN4E DIODE [M]

D1007 B0BA6R100003 DIODE [M]

D7650 MAZ80560ML DIODE [M]

SWITCHES

S351 K0L1BA000078 SW CD TOP [M]

S352 K0L1BA000078 SW CD BOTTOM [M]

S801 EVQ21405RJ SW POWER [M]

S802 EVQ21405RJ SW VOL - [M]

S803 EVQ21405RJ SW VOL + [M]

S804 EVQ21405RJ SW REV_SKIP [M]

S805 EVQ21405RJ SW FWD_SKIP [M]

S806 EVQ21405RJ SW TUNER/XM [M]

S807 EVQ21405RJ SW CD [M]

S808 EVQ21405RJ SW MUSIC_PORT [M]

S809 EVQ21405RJ SW STOP [M]

S810 EVQ21405RJ SW CD_OP/CL [M]

S7201 RSH1A048-A SW RESET [M]

CONNECTORS

CN801 K1MN06A00013 6P FFC CONNECTOR [M]

CN806A K1MN13BA0147 13P CONNECTOR [M]

CN2401 K1FY124DA001 24P CONNECTOR [M]

CN7001 K1MN16B00154 16P FFC CONNECTOR [M]

CN7002 K1MN22BA0005 22P CONNECTOR [M]

FP701 K1MN22B00014 22P FFC CONNECTOR [M]

FP806 K1KZ13A00001 13P CONNECTOR [M]

P1 K1KA03BA0125 3P CONNECTOR [M]

P351 K1MP05B00004 5P CONNECTOR [M]

P352 K1MP03B00004 3P CONNECTOR [M]

P601 K1MP06B00009 6P CONNECTOR [M]

P801 K1MP09B00004 9P CONNECTOR [M]

P802 K1KA02BA0125 2P CONNECTOR [M]

COILS & TRANSFORMERS

L1 G0ZZ00002353 FM COIL [M]

L3 G0ZZ00002353 FM COIL [M]

L5 G0ZZ00002453 FM OSC COIL [M]

L7 G2BPC0000017 AM OSC COIL [M]

L8 G0C101KA0029 AXIAL COIL [M]

L51 G2A390C00001 AM RF-COIL [M]

L101 ERJ3GEY0R00V CHIP JUMPER [M]

L201 ERJ3GEY0R00V CHIP JUMPER [M]

L301 ERJ3GEY0R00V CHIP JUMPER [M]

L304 J0JBC0000019 CHIP INDUCTOR [M]

L401 ERJ3GEY0R00V CHIP JUMPER [M]

L403 ERJ3GEY0R00V CHIP JUMPER [M]

L404 ERJ3GEY0R00V CHIP JUMPER [M]

L501 ERJ3GEY0R00V CHIP JUMPER [M]

Page 67

Ref. No. Part No. Part Name & Description Remarks

L503 ERJ3GEY0R00V CHIP JUMPER [M]

L504 ERJ3GEY0R00V CHIP JUMPER [M]

L601 G0C101KA0029 AXIAL COIL [M]

L602 ERJ3GEY0R00V CHIP JUMPER [M]

L801 G0C2R2JA0019 COIL [M]

L802 G0C2R2JA0019 COIL [M]

L901 ELF15N035AN LINE FILTER [M]

L1001 J0JBC0000019 CHIP INDUCTOR [M]

L1002 J0JBC0000019 CHIP INDUCTOR [M]

LB7262 D0GBR00JA008 CHIP JUMPER [M]

LB7263 D0GBR00JA008 CHIP JUMPER [M]

LB7264 D0GBR00JA008 CHIP JUMPER [M]

T1 G2BAC0000055 AM IFT [M]

T901 G4C5ABD00006 TRANSFORMER [M]

COMPONENT COMBINATIONS

Z801 L5ACAYY00016 LCD DISPLAY [M]

Z1001 B3RAD0000053 REMOTE SENSOR [M]

ZA901 EYF52BCY FUSE CLIP [M]

ZA902 EYF52BCY FUSE CLIP [M]

IP601 K5G302AA0002 FUSE PROTECTOR [M]

IP602 K5G251A00008 FUSE PROTECTOR [M]

CERAMIC FILTER

CF1 J0B1075A0129 CERAMIC FILTER [M]

OSCILLATORS

X1 J0B1075A0121 CERAMIC FILTER [M]

X2 H0A750200020 CRYSTAL OSCILLATOR [M]

X801 H0A327200097 CRYSTAL OSCILLATOR [M]

X802 H2A800400011 CRYSTAL OSCILLATOR [M]

X7201 H2B169500005 CRYSTAL OSCILLATOR [M]

FUSE

F901 K5D202APA008 FUSE [M]

JACKS

JK601 K2HC103A0031 JK MIC [M]

JK602 K4AC04B00008 JK SPEAKER TERMINAL [M]

JK603 K2HC1YYA0002 JK MUSIC PORT [M]

JK604 K2EZ2A000008 JK DC IN [M]

JK901 K2AB2B000007 JK AC INLET [M]

CHIP RESISTORS

W700 ERJ3GEY0R00V CHIP JUMPER [M]

W701 ERJ6GEY0R00V CHIP JUMPER [M]

W702 ERJ8GEY0R00V CHIP JUMPER [M]

W703 ERJ3GEY0R00V CHIP JUMPER [M]

W704 ERJ8GEY0R00V CHIP JUMPER [M]

W705 ERJ8GEY0R00V CHIP JUMPER [M]

W706 ERJ3GEY0R00V CHIP JUMPER [M]

W707 ERJ3GEY0R00V CHIP JUMPER [M]

W708 ERJ3GEY0R00V CHIP JUMPER [M]

W709 ERJ3GEY0R00V CHIP JUMPER [M]

W710 ERJ6GEY0R00V CHIP JUMPER [M]

W711 ERJ3GEY0R00V CHIP JUMPER [M]

W712 ERJ3GEY0R00V CHIP JUMPER [M]

W713 ERJ8GEY0R00V CHIP JUMPER [M]

W714 ERJ6GEY0R00V CHIP JUMPER [M]

W715 ERJ3GEY0R00V CHIP JUMPER [M]

W716 ERJ3GEY0R00V CHIP JUMPER [M]

W717 ERJ8GEY0R00V CHIP JUMPER [M]

W718 ERJ3GEY0R00V CHIP JUMPER [M]

W719 ERJ6GEY0R00V CHIP JUMPER [M]

SC-EN37P

Ref. No. Part No. Part Name & Description Remarks

W720 ERJ6GEY0R00V CHIP JUMPER [M]

W721 ERJ8GEY0R00V CHIP JUMPER [M]

W722 ERJ8GEY0R00V CHIP JUMPER [M]

W723 ERJ8GEY0R00V CHIP JUMPER [M]

W724 ERJ3GEY0R00V CHIP JUMPER [M]

W725 ERJ3GEY0R00V CHIP JUMPER [M]

W726 ERJ3GEY0R00V CHIP JUMPER [M]

W727 ERJ3GEY0R00V CHIP JUMPER [M]

W728 ERJ3GEY0R00V CHIP JUMPER [M]

W729 ERJ6GEY0R00V CHIP JUMPER [M]

W730 ERJ8GEY0R00V CHIP JUMPER [M]

W731 ERJ3GEY0R00V CHIP JUMPER [M]

W732 ERJ6GEY0R00V CHIP JUMPER [M]

W733 ERJ6GEY0R00V CHIP JUMPER [M]

W734 ERJ3GEY0R00V CHIP JUMPER [M]

W735 ERJ6GEY0R00V CHIP JUMPER [M]

W736 ERJ8GEY0R00V CHIP JUMPER [M]

W737 ERJ8GEY0R00V CHIP JUMPER [M]

W738 ERJ3GEY0R00V CHIP JUMPER [M]

W739 ERJ6GEY0R00V CHIP JUMPER [M]

W740 ERJ3GEY0R00V CHIP JUMPER [M]

W741 ERJ3GEY0R00V CHIP JUMPER [M]

W742 ERJ8GEY0R00V CHIP JUMPER [M]

W743 ERJ6GEY0R00V CHIP JUMPER [M]

W744 ERJ3GEY0R00V CHIP JUMPER [M]

W745 ERJ3GEY0R00V CHIP JUMPER [M]

W746 ERJ3GEY0R00V CHIP JUMPER [M]

W747 ERJ3GEY0R00V CHIP JUMPER [M]

W801 ERJ3GEY0R00V CHIP JUMPER [M]

W802 ERJ3GEY0R00V CHIP JUMPER [M]

W803 ERJ6GEY0R00V CHIP JUMPER [M]

W804 ERJ6GEY0R00V CHIP JUMPER [M]

W812 ERJ3GEY0R00V CHIP JUMPER [M]

W813 ERJ3GEY0R00V CHIP JUMPER [M]

W821 ERJ3GEY0R00V CHIP JUMPER [M]

W822 ERJ3GEY0R00V CHIP JUMPER [M]

W7001 D0GDR00JA017 CHIP JUMPER [M]

W7002 D0GDR00JA017 CHIP JUMPER [M]

W7003 D0GDR00JA017 CHIP JUMPER [M]

W7004 D0GBR00JA008 CHIP JUMPER [M]

W7005 D0GBR00JA008 CHIP JUMPER [M]

W7006 ERJ8GEY0R00V CHIP JUMPER [M]

W7007 ERJ8GEY0R00V CHIP JUMPER [M]

W7008 D0GDR00JA017 CHIP JUMPER [M]

W7009 D0GBR00JA008 CHIP JUMPER [M]

W7010 D0GBR00JA008 CHIP JUMPER [M]

W7011 D0GBR00JA008 CHIP JUMPER [M]

W7012 D0GBR00JA008 CHIP JUMPER [M]

W7013 D0GBR00JA008 CHIP JUMPER [M]

W7014 D0GBR00JA008 CHIP JUMPER [M]

W7015 D0GBR00JA008 CHIP JUMPER [M]

W7016 D0GBR00JA008 CHIP JUMPER [M]

W7017 D0GBR00JA008 CHIP JUMPER [M]

W7018 D0GBR00JA008 CHIP JUMPER [M]

W7019 D0GBR00JA008 CHIP JUMPER [M]

W7020 D0GBR00JA008 CHIP JUMPER [M]

W7021 D0GBR00JA008 CHIP JUMPER [M]

W7022 D0GBR00JA008 CHIP JUMPER [M]

W7023 D0GBR00JA008 CHIP JUMPER [M]

W7024 D0GBR00JA008 CHIP JUMPER [M]

W7025 D0GBR00JA008 CHIP JUMPER [M]

W7026 D0GBR00JA008 CHIP JUMPER [M]

W7027 D0GBR00JA008 CHIP JUMPER [M]

W7028 D0GBR00JA008 CHIP JUMPER [M]

W7029 D0GBR00JA008 CHIP JUMPER [M]

WA3001 ERJ8GEY0R00V CHIP JUMPER [M]

WA3002 ERJ8GEY0R00V CHIP JUMPER [M]

WA3003 ERJ8GEY0R00V CHIP JUMPER [M]

WA3004 ERJ8GEY0R00V CHIP JUMPER [M]

JW1 RWJ0211105SS 11P TUNER-MAIN WIRE [M]

JW351 RWJ0205100SX 5P MOTOR-MAIN WIRE [M]

JW352 RWJ9003075SX 3P SW-MAIN WIRE [M]

Page 68

SC-EN37P

Ref. No. Part No. Part Name & Description Remarks

JW601 RWJ9006080SX 6P SENSOR-MAIN WIRE [M]

JW802 RWJ0209070SX 9P LCD-MAIN WIRE [M]

JW803 REXV0076 2P OPE1-MAIN WIRE [M]

JW804 RWJ9002120SS 2P OPE1-OPE2 WIRE (JW805) [M]

JW806 RWJ9002070SS 2P LED-LCD WIRE (JW8001) [M]

PACKING MATERIALS

P1 RPGV0396 PACKING CASE [M]

P2 RPNV0122 POLYFOAM [M]

P3 RPHV0029 MIRAMAT SHEET [M]

ACCESSORIES

A1 N2QAYB000109 REMOTE CONTROL [M]

A1-1 RKK-HTR0283H R/C BATTERY COVER [M]

A2 K2CB2CB00018 AC CORD [M]

A3 RQTV0217-P O/I BOOK (En) [M]

A3 RQTV0224-P O/I BOOK (En) [M]

A4 N1DADYY00003 FM/AM ANTENNA [M]

A5 RFE0205 I-POD CRADLE [M]

RESISTORS

R1 D0GB103JA008 10K 1/16W [M]

R2 ERJ3GEY0R00V 0 1/16W [M]

R3 D0GB332JA008 3.3K 1/16W [M]

R4 D0GB104JA008 100K 1/16W [M]

R5 D0GB680JA007 68 1/16W [M]

R6 D0GB104JA008 100K 1/16W [M]

R7 D0GB104JA008 100K 1/16W [M]

R8 D0GB103JA008 10K 1/16W [M]

R9 ERJ3GEY0R00V 0 1/16W [M]

R10 D0GB104JA008 100K 1/16W [M]

R11 D0GB332JA008 3.3K 1/16W [M]

R12 ERJ3GEYJ152V 1.5K 1/16W [M]

R13 D0GB332JA008 3.3K 1/16W [M]

R14 D0GB472JA008 4.7K 1/16W [M]

R16 D0GB103JA008 10K 1/16W [M]

R17 D0GB103JA008 10K 1/16W [M]

R18 D0GB223JA008 22K 1/16W [M]

R20 D0GB103JA008 10K 1/16W [M]

R22 D0GB103JA008 10K 1/16W [M]

R23 D0GB223JA008 22K 1/16W [M]

R24 D0GB223JA008 22K 1/16W [M]

R25 D0GB223JA008 22K 1/16W [M]

R28 D0GB104JA008 100K 1/16W [M]

R29 D0GB102JA008 1K 1/16W [M]

R30 D0GB393JA008 39K 1/16W [M]

R31 D0GB472JA008 4.7K 1/16W [M]

R32 D0AE330JA178 33 1/4W [M]

R33 D0GB472JA008 4.7K 1/16W [M]

R34 ERJ3GEYJ182V 1.8K 1/16W [M]

R35 D0GB472JA008 4.7K 1/16W [M]

R36 D0GB472JA008 4.7K 1/16W [M]

R37 ERJ3GEY0R00V 0 1/16W [M]

R38 D0GB332JA008 3.3K 1/16W [M]

R39 ERJ3GEY0R00V 0 1/16W [M]

R101 D0GB473JA008 47K 1/16W [M]

R102 D0GB562JA008 5.6K 1/16W [M]

R103 D0GB473JA008 47K 1/16W [M]

R104 D0GB562JA008 5.6K 1/16W [M]

R105 D0GB562JA008 5.6K 1/16W [M]

R106 D0AE682JA178 6.8K 1/4W [M]

R107 D0GB223JA008 22K 1/16W [M]

R108 D0GB332JA008 3.3K 1/16W [M]

R109 D0GB103JA008 10K 1/16W [M]

R110 D0GB392JA008 3.9K 1/16W [M]

R111 D0GB333JA007 33K 1/16W [M]

R112 D0GB682JA008 6.8K 1/16W [M]

R113 D0GB472JA008 4.7K 1/16W [M]

R116 D0GB473JA008 47K 1/16W [M]

R117 D0GB562JA008 5.6K 1/16W [M]

R201 D0GB473JA008 47K 1/16W [M]

Ref. No. Part No. Part Name & Description Remarks

R202 D0GB562JA008 5.6K 1/16W [M]

R203 D0GB473JA008 47K 1/16W [M]

R204 D0GB562JA008 5.6K 1/16W [M]

R205 D0GB562JA008 5.6K 1/16W [M]

R206 D0AE682JA178 6.8K 1/4W [M]

R207 D0GB223JA008 22K 1/16W [M]

R208 D0GB332JA008 3.3K 1/16W [M]

R209 D0GB103JA008 10K 1/16W [M]

R210 D0GB392JA008 3.9K 1/16W [M]

R211 D0GB333JA007 33K 1/16W [M]

R212 D0GB682JA008 6.8K 1/16W [M]

R213 D0GB472JA008 4.7K 1/16W [M]

R216 D0GB473JA008 47K 1/16W [M]

R217 D0GB562JA008 5.6K 1/16W [M]

R301 D0GB223JA008 22K 1/16W [M]

R302 D0GB223JA008 22K 1/16W [M]

R303 D0GB223JA008 22K 1/16W [M]

R304 D0GB223JA008 22K 1/16W [M]

R305 D0GB103JA008 10K 1/16W [M]

R306 D0GB102JA008 1K 1/16W [M]

R307 D0GB102JA008 1K 1/16W [M]

R308 D0GB102JA008 1K 1/16W [M]

R309 D0GB102JA008 1K 1/16W [M]

R312 D0GB102JA008 1K 1/16W [M]

R313 D0GB102JA008 1K 1/16W [M]

R316 D0GB334JA008 330K 1/16W [M]

R317 D0GB334JA008 330K 1/16W [M]

R318 D0AE330JA178 33 1/4W [M]

R319 D0AE330JA178 33 1/4W [M]

R325 ERJ3GEYJ152V 1.5K 1/16W [M]

R402 D0GB102JA008 1K 1/16W [M]

R403 D0GB471JA008 470 1/16W [M]

R409 D0GB333JA008 33K 1/16W [M]

R502 D0GB102JA008 1K 1/16W [M]

R503 D0GB471JA008 470 1/16W [M]

R509 D0GB333JA008 33K 1/16W [M]

R601 D0AE822JA178 8.2K 1/4W [M]

R602 D0GB102JA008 1K 1/16W [M]

R603 D0GB273JA008 27K 1/16W [M]

R604 D0GB272JA007 2.7K 1/16W [M]

R605 D0GB102JA008 1K 1/16W [M]

R607 D0GB222JA008 2.2K 1/16W [M]

R608 D0GB333JA007 33K 1/16W [M]

R612 D0GB222JA008 2.2K 1/16W [M]

R613 D0GB223JA008 22K 1/16W [M]

R614 D0AE151JA048 150 1/4W [M]

R615 ERJ6GEYJ1R0V 1 1/10W [M]

R616 D0AE471JA048 470 1/4W [M]

R617 D0GB101JA008 100 1/16W [M]

R618 D0GB681JA008 680 1/16W [M]

R619 D0GB681JA008 680 1/16W [M]

R620 ERJ6GEYJ2R2V 2.2 1/10W [M]

R621 D0AE1R0JA048 11/4W [M]

R622 D0AE1R0JA048 11/4W [M]

R623 D0AE471JA048 470 1/4W [M]

R624 D0AE471JA048 470 1/4W [M]

R625 D0AE121JA048 120 1/4W [M]

R626 D0AE121JA048 120 1/4W [M]

R627 D0AE221JA048 220 1/4W [M]

R628 D0GB102JA008 1K 1/16W [M]

R629 D0GB102JA008 1K 1/16W [M]

R630 ERJ3GEYJ221V 220 1/16W [M]

R631 D0GB102JA008 1K 1/16W [M]

R632 D0GB472JA008 4.7K 1/16W [M]

R633 D0GB103JA008 10K 1/16W [M]

R634 D0GB101JA008 100 1/16W [M]

R635 D0GB222JA008 2.2K 1/16W [M]

R636 D0GB222JA008 2.2K 1/16W [M]

R637 D0GB681JA008 680 1/16W [M]

R639 D0GB102JA008 1K 1/16W [M]

R640 ERJ3GEYJ153V 15K 1/16W [M]

R641 D0GB102JA008 1K 1/16W [M]

R642 D0GB562JA008 5.6K 1/16W [M]

R643 D0GB273JA008 27K 1/16W [M]

Page 69

Ref. No. Part No. Part Name & Description Remarks

R644 D0GB562JA008 5.6K 1/16W [M]

R645 D0GB223JA008 22K 1/16W [M]

R646 D0GB392JA008 3.9K 1/16W [M]

R647 D0GB822JA008 8.2K 1/16W [M]

R661 D0AE221JA048 220 1/4W [M]

R662 D0GB101JA008 100 1/16W [M]

R663 D0GB681JA008 680 1/16W [M]

R805 D0GB473JA008 47K 1/16W [M]

R806 ERJ3GEY0R00V 0 1/16W [M]

R807 D0GB332JA008 3.3K 1/16W [M]

R808 D0GB332JA008 3.3K 1/16W [M]

R809 ERJ3GEYJ224V 220K 1/16W [M]

R811 D0GB473JA008 47K 1/16W [M]

R812 D0GB102JA008 1K 1/16W [M]

R813 D0GB102JA008 1K 1/16W [M]

R814 D0GB102JA008 1K 1/16W [M]

R815 D0GB102JA008 1K 1/16W [M]

R816 D0GB102JA008 1K 1/16W [M]

R817 D0GB183JA008 18K 1/16W [M]

R818 D0GB103JA008 10K 1/16W [M]

R819 D0GB472JA008 4.7K 1/16W [M]

R820 D0GB103JA008 10K 1/16W [M]

R822 D0GB102JA008 1K 1/16W [M]

R823 D0GB102JA008 1K 1/16W [M]

R824 D0GB474JA041 470K 1/16W [M]

R825 D0GB333JA007 33K 1/16W [M]

R828 D0GB102JA008 1K 1/16W [M]

R829 D0GB102JA008 1K 1/16W [M]

R830 D0GB104JA008 100K 1/16W [M]

R831 D0GB104JA008 100K 1/16W [M]

R832 D0GB103JA008 10K 1/16W [M]

R833 D0GB104JA008 100K 1/16W [M]

R834 D0GB222JA008 2.2K 1/16W [M]

R835 D0GB103JA008 10K 1/16W [M]

R840 ERJ3GEYJ153V 15K 1/16W [M]

R841 D0GB821JA008 820 1/16W [M]

R846 ERJ3GEYJ152V 1.5K 1/16W [M]

R847 D0GB222JA008 2.2K 1/16W [M]

R848 D0GB272JA007 2.7K 1/16W [M]

R849 D0GB392JA008 3.9K 1/16W [M]

R850 D0GB562JA008 5.6K 1/16W [M]

R851 D0GB822JA008 8.2K 1/16W [M]

R852 ERJ3GEYJ153V 15K 1/16W [M]

R853 D0GB333JA007 33K 1/16W [M]

R854 D0GB823JA008 82K 1/16W [M]

R855 D0GB103JA008 10K 1/16W [M]

R856 D0GB102JA008 1K 1/16W [M]

R862 D0GB820JA008 82 1/16W [M]

R864 D0GB102JA008 1K 1/16W [M]

R865 D0GB102JA008 1K 1/16W [M]

R866 D0GB473JA007 47K 1/16W [M]

R873 D0GB472JA008 4.7K 1/16W [M]

R880 D0GB102JA008 1K 1/16W [M]

R881 D0GB101JA008 100 1/16W [M]

R882 D0GB102JA008 1K 1/16W [M]

R883 D0GB101JA008 100 1/16W [M]

R900 ERD2FCVJ4R7T 4.7 1/4W [M]

R901 D0GB102JA008 1K 1/16W [M]

R904 D0GB102JA008 1K 1/16W [M]

R1002 D0GB104JA008 100K 1/16W [M]

R1004 D0GB104JA008 100K 1/16W [M]

R1005 D0GB471JA008 470 1/16W [M]

R1006 D0GB473JA007 47K 1/16W [M]

R1007 D0GB471JA008 470 1/16W [M]

R1008 D0GB471JA008 470 1/16W [M]

R1009 D0GB103JA008 10K 1/16W [M]

R1010 D0GB104JA008 100K 1/16W [M]

R1012 D0GB680JA007 68 1/16W [M]

R3001 D0GB334JA007 330K 1/16W [M]

R3002 D0GB224JA007 220K 1/16W [M]

R3003 D0AF100JA039 10 1/4W [M]

R3004 ERJ6GEYJ472V 4.7K 1/10W [M]

R3005 ERJ6GEYJ472V 4.7K 1/10W [M]

R3006 D0GB155JA007 1.5M 1/16W [M]

SC-EN37P

Ref. No. Part No. Part Name & Description Remarks

R3007 D0GB125JA007 1.2M 1/16W [M]

R3008 ERJ3GEYJ224V 220K 1/16W [M]

R3009 D0GB224JA007 220K 1/16W [M]

R3010 D0GB101JA008 100 1/16W [M]

R3011 D0GB101JA008 100 1/16W [M]

R3012 D0GB103JA008 10K 1/16W [M]

R3013 D0GB101JA008 100 1/16W [M]

R3014 D0GB562JA008 5.6K 1/16W [M]

R3015 D0GB682JA008 6.8K 1/16W [M]

R3016 D0GB103JA008 10K 1/16W [M]

R3017 ERJ3GEYJ153V 15K 1/16W [M]

R3018 D0GB103JA008 10K 1/16W [M]

R3019 D0GB103JA008 10K 1/16W [M]

R3020 D0GB101JA008 100 1/16W [M]

R3021 D0GB101JA008 100 1/16W [M]

R3022 D0GB101JA008 100 1/16W [M]

R3023 D0GB101JA008 100 1/16W [M]

R3024 D0GB101JA008 100 1/16W [M]

R3025 D0GB101JA008 100 1/16W [M]

R3101 ERJ6GEYJ103V 10K 1/10W [M]

R3102 ERJ6GEYJ682V 6.8K 1/10W [M]

R3103 ERJ6GEYJ103V 10K 1/10W [M]

R3104 ERJ6GEYJ682V 6.8K 1/10W [M]

R3105 ERJ6GEYJ104V 100K 1/10W [M]

R3201 ERJ6GEYJ103V 10K 1/10W [M]

R3202 ERJ6GEYJ682V 6.8K 1/10W [M]

R3203 ERJ6GEYJ103V 10K 1/10W [M]

R3204 ERJ6GEYJ682V 6.8K 1/10W [M]

R3205 ERJ6GEYJ104V 100K 1/10W [M]

R7111 D0GB103JA008 10K 1/16W [M]

R7211 ERJ3GEYJ823V 82K 1/16W [M]

R7212 ERJ3GEYJ821V 820 1/16W [M]

R7214 ERJ3GEYJ471V 470 1/16W [M]

R7217 D0GB102JA008 1K 1/16W [M]

R7218 D0GB102JA008 1K 1/16W [M]

R7220 ERJ3GEYJ105V 1M 1/16W [M]

R7221 ERJ3GEYJ101V 100 1/16W [M]

R7253 ERJ3GEYJ100V 10 1/16W [M]

R7254 D0GB102JA008 1K 1/16W [M]

R7315 ERJ3GEYJ332V 3.3K 1/16W [M]

R7323 ERJ3GEYJ332V 3.3K 1/16W [M]

R7325 ERJ3GEYJ331V 330 1/16W [M]

R7327 D0GB102JA008 1K 1/16W [M]

R7328 D0GB103JA008 10K 1/16W [M]

R7329 D0GB102JA008 1K 1/16W [M]

R7330 ERJ3GEYJ562V 5.6K 1/16W [M]

R7331 D0GB223JA008 22K 1/16W [M]

R7332 D0GB102JA008 1K 1/16W [M]

R7335 ERJ3GEYJ101V 100 1/16W [M]

R7336 ERJ3GEYJ100V 10 1/16W [M]

R7339 D0GB102JA008 1K 1/16W [M]

R7349 ERJ3GEYJ183V 18K 1/16W [M]

R7601 ERJ3GEYJ4R7V 4.7 1/16W [M]

R7650 ERJ3GEYJ5R6V 5.6 1/16W [M]

CAPACITORS

C1 ECJ1VC1H470J 47P 50V [M]

C2 ECJ1VC1H100D 10 50V [M]

C3 F1H1C333A071 0.033 16V [M]

C4 F2A1C100A147 10P 16V [M]

C5 ECJ1VB1C473K 0.047 16V [M]

C6 F1H1H102A219 1000P 50V [M]

C7 F1H1H102A219 1000P 50V [M]

C8 ECJ2VC1H070D 7P 50V [M]

C9 F1H1E103A029 0.01 25V [M]

C10 F1H1E103A029 0.01 25V [M]

C11 F1H1H102A219 1000P 50V [M]

C12 ECJ1VB1C473K 0.047 16V [M]

C13 ECJ1VC1H150J 15P 50V [M]

C15 ECJ1VB1C473K 0.047 16V [M]

C16 ECJ1VC1H150J 15P 50V [M]

C17 F2A1H3R3A145 3.3 50V [M]

C18 F1H1E103A029 0.01 25V [M]

Page 70

SC-EN37P

Ref. No. Part No. Part Name & Description Remarks

C19 F2A1H1R0A145 1 50V [M]

C20 F2A0J101A167 100 6.3V [M]

C21 F2A1H1R0A145 1.0 50V [M]

C22 F2A1HR47A013 47 50V [M]

C23 F2A0J101A167 100 6.3V [M]

C24 ECEA1AKA220B 22 10V [M]

C25 ECJ1VB1C183K 0.018 16V [M]

C26 F1H1E103A029 0.01 25V [M]

C27 ECJ1VB1C183K 0.018 16V [M]

C28 F1H1H102A219 1000P 50V [M]

C29 F1H1H102A219 1000P 50V [M]

C30 F2A1H1R0A145 1 50V [M]

C31 F2A1H1R0A145 1 50V [M]

C32 F2A1H4R7A145 4.7 50V [M]

C33 F1H1H101A230 100P 50V [M]

C34 ECJ1VC1H270J 27P 50V [M]

C35 F1H1H101A230 100P 50V [M]

C36 ECJ1VC1H220J 22P 50V [M]

C37 F1H1H101A230 100P 50V [M]

C38 F1H1H101A230 100P 50V [M]

C39 F1H1H102A219 1000P 50V [M]

C40 F2A0J101A167 100 6.3V [M]

C41 F1H1H331A013 330P 50V [M]

C43 ECJ1VB1C473K 0.047 16V [M]

C44 ECJ1VB1H223K 0.022 50V [M]

C46 F1H1H222A219 2200P 50V [M]

C47 F1D1H100A015 10P 50V [M]

C48 F1H1H102A219 1000P 50V [M]

C51 ECJ2VC1H070D 7P 50V [M]

C52 F1H1H102A219 1000P 50V [M]

C101 F1H1H102A219 1000P 50V [M]

C103 F1H1C104A041 0.1 16V [M]

C104 F1H1C104A041 0.1 16V [M]

C105 F1H1C104A041 0.1 16V [M]

C106 F1H1H102A219 1000P 50V [M]

C107 F1H1H102A219 1000P 50V [M]

C108 F1H1H102A219 1000P 50V [M]

C109 ECJ1VB1C683K 0.068 16V [M]

C110 F1H1C104A041 0.1 16V [M]

C111 F1H1E103A029 0.01 25V [M]

C112 F1H1E1530002 0.015 25V [M]

C113 ECJ1VB1C224K 0.22 16V [M]

C114 ECJ1VB1C473K 0.047 16V [M]

C115 ECJ1VB1C105K 1 16V [M]

C117 ECJ1VB1H682K 6800P 50V [M]

C118 F1H1C333A071 0.033 16V [M]

C119 F1H1E1530002 0.015 25V [M]

C122 ECJ1VB1C473K 0.047 16V [M]

C124 F1H1C104A041 0.1 16V [M]

C126 F1H1H102A219 1000P 50V [M]

C201 F1H1H102A219 1000P 50V [M]

C203 F1H1C104A041 0.1 16V [M]

C204 F1H1C104A041 0.1 16V [M]

C205 F1H1C104A041 0.1 16V [M]

C206 F1H1H102A219 1000P 50V [M]

C207 F1H1H102A219 1000P 50V [M]

C208 F1H1H102A219 1000P 50V [M]

C209 ECJ1VB1C683K 0.068 16V [M]

C210 F1H1C104A041 0.1 16V [M]

C211 F1H1E103A029 0.01 25V [M]

C212 F1H1E1530002 0.015 25V [M]

C213 ECJ1VB1C224K 0.22 16V [M]

C214 ECJ1VB1C473K 0.047 16V [M]

C215 ECJ1VB1C105K 1 16V [M]

C217 ECJ1VB1H682K 6800P 50V [M]

C218 F1H1C333A071 0.033 16V [M]

C219 F1H1E1530002 0.015 25V [M]

C222 ECJ1VB1C473K 0.047 16V [M]

C224 F1H1C104A041 0.1 16V [M]

C226 F1H1H102A219 1000P 50V [M]

C301 F1H1H102A219 1000P 50V [M]

C302 F1H1H221A748 220P 50V [M]

C303 F1H1H221A748 220P 50V [M]

C304 F1H1H221A748 220P 50V [M]

Ref. No. Part No. Part Name & Description Remarks

C305 F1H1H221A748 220P 50V [M]

C309 ECEA1AKA470B 47 10V [M]

C310 F2A1C101A147 100 16V [M]

C311 F2A1HR33A234 33 50V [M]

C312 F1H1H221A748 220P 50V [M]

C313 F1H1H221A748 220P 50V [M]

C353 ECA1AM221B 220 10V [M]

C356 F1H1H221A748 220P 50V [M]

C357 F1H1H221A748 220P 50V [M]

C358 F2A1A1020051 1000 10V [M]

C402 ECJ1VB1C224K 0.22 16V [M]

C403 F1H1H471A219 470P 50V [M]

C407 F2A1A1020051 1000 10V [M]

C409 F1H1H102A219 1000P 50V [M]

C410 F1H1H101A230 100P 50V [M]

C502 ECJ1VB1C224K 0.22 16V [M]

C503 F1H1H471A219 470P 50V [M]

C507 F2A1A1020051 1000 10V [M]

C601 F2A1C470A016 47 16V [M]

C602 F2A1C100A147 10 16V [M]

C603 F1H1H102A219 1000P 50V [M]

C604 F2A1C100A147 10 16V [M]

C608 F2A1C100A147 10 16V [M]

C609 F2A1C100A147 10 16V [M]

C610 F2A1C100A147 10 16V [M]

C611 ECA0JM472E 4700 6.3V [M]

C612 F2A0J101A167 100 6.3V [M]

C615 F2A1C101A147 100 16V [M]

C616 ECA1EM332E 3300 25V [M]

C623 F2A1C101A147 100 16V [M]

C624 F2A1C100A147 10 16V [M]

C626 F2A1C100A147 10 16V [M]

C801 F2A1A101A159 100 10V [M]

C803 F1H1H102A219 1000P 50V [M]

C804 F1H1H102A219 1000P 50V [M]

C806 F1H1H102A219 1000P 50V [M]

C807 ECJ1VC1H560J 56P 50V [M]

C808 ECJ1VC1H560J 56P 50V [M]

C809 F1H1H102A219 1000P 50V [M]

C810 ECJ1VC1H390J 39P 50V [M]

C811 ECJ1VC1H560J 56P 50V [M]

C812 ECJ1VC1H180J 18P 50V [M]

C813 ECJ1VC1H180J 18P 50V [M]

C814 F2A1H2R2A145 2.2 50V [M]

C815 F2A1H1R0A145 150V [M]

C816 F1H1H102A219 1000P 50V [M]

C817 F1H1H102A219 1000P 50V [M]

C818 F1H1H102A219 1000P 50V [M]

C819 F1H1H102A219 1000P 50V [M]

C820 F2A1C100A147 10 16V [M]

C821 F1H1H102A219 1000P 50V [M]

C822 F1H1H102A219 1000P 50V [M]

C826 F1H1H102A219 1000P 50V [M]

C827 ECA1AM331B 330 10V [M]

C828 F1H1H222A013 2200P 50V [M]

C829 F1H1H222A013 2200P 50V [M]

C830 F1H1H102A219 1000P 50V [M]

C831 F1H1H102A219 1000P 50V [M]

C840 F1H1H221A748 220P 50V [M]

C841 F1H1H221A748 220P 50V [M]

C842 F1H1H221A748 220P 50V [M]

C843 F1H1H221A748 220P 50V [M]

C844 ECJ1VB1C105K 116V [M]

C860 F2A0J221A167 220 6.3V [M]

C901 F1E1H1030001 0.01 50V [M]

C902 F1E1H1030001 0.01 50V [M]

C903 F1E1H1030001 0.01 50V [M]

C904 F1E1H1030001 0.01 50V [M]

C1001 F2A1C100A147 10 16V [M]

C1002 ECJ1VB1C105K 116V [M]

C1003 F1H1H102A219 1000P 50V [M]

C1004 F1H1H221A748 220P 50V [M]

C1005 F1H1H221A748 220P 50V [M]

C1006 F1H1H221A748 220P 50V [M]

Page 71

Ref. No. Part No. Part Name & Description Remarks

C1007 F1H1H221A748 220P 50V [M]

C1009 ECJ1VC1H681J 680P 50V [M]

C1010 F1H1H103A219 0.01 50V [M]

C1011 F1H1H103A219 0.01 50V [M]

C1012 F2A0J101A167 100 6.3V [M]

C1014 ECJ1VB1C105K 116V [M]

C3001 ECJ1VB1H104K 0.1 50V [M]

C3002 F2A1A101A206 100 10V [M]

C3003 F2A1A470A204 47 10V [M]

C3004 F1H1C104A041 0.1 16V [M]

C3005 ECJ2FB0J106K 10 6.3V [M]

C3006 F2A1E100A202 10 25V [M]

C3007 F2A1A101A159 100 10V [M]

C3101 ECJ1VB0J105K 1 6.3V [M]

C3102 ECJ1VC1H330J 33P 50V [M]

C3103 ECJ1VC1H101J 100P 50V [M]

C3104 ECJ2FB0J106K 10 6.3V [M]

C3105 ECJ2FB0J106K 10 6.3V [M]

C3201 ECJ1VB0J105K 1 6.3V [M]

C3202 ECJ1VC1H330J 33P 50V [M]

C3203 ECJ1VC1H101J 100P 50V [M]

C3204 ECJ2FB0J106K 10 6.3V [M]

C3205 ECJ2FB0J106K 10 6.3V [M]

C7102 F1H1A474A025 0.47 10V [M]

C7107 ECJ1VB1H223K 0.022 50V [M]

C7142 ECJ1VB1H332K 3300P 50V [M]

C7154 ECJ1VB1C104K 0.1 16V [M]

C7155 ECJ1VB1C104K 0.1 16V [M]

C7161 ECJ1VB1C104K 0.1 16V [M]

C7164 ECJ2FF1A106Z 10 10V [M]

C7165 ECJ2FF1A106Z 10 10V [M]

C7166 F1H1H103A219 0.01 50V [M]

C7203 F2A0J221A200 220 6.3V [M]

C7204 ECJ1VB1C104K 0.1 16V [M]

C7216 ECJ1VB1H681K 680P 50V [M]

C7217 ECJ1VB1C104K 0.1 16V [M]

C7218 ECJ1VB1C823K 0.082 16V [M]

C7223 F2A1H4R70037 4.7 50V [M]

C7225 F1H1H102A219 1000P 50V [M]

C7226 F1H1H102A219 1000P 50V [M]

C7227 ECA1HAK010XI 150V [M]

C7228 ECA1HAK010XI 150V [M]

C7230 ECJ1VB1C104K 0.1 16V [M]

C7231 F2A0J221A200 220 6.3V [M]

C7232 F2A0J221A200 220 6.3V [M]

C7233 F1H1C104A008 0.1 16V [M]

C7234 ECJ1VB1C104K 0.1 16V [M]

C7235 F2A1C100A133 10 16V [M]

C7241 F1H1H102A219 1000P 50V [M]

C7243 F1H1C104A008 0.1 16V [M]

C7244 ECJ1VB1C153K 0.015 16V [M]

C7253 F1H1H471A219 470P 50V [M]

C7263 ECJ1VB1C104K 0.1 16V [M]

C7264 ECJ1VB1C104K 0.1 16V [M]

C7315 F1H1A474A025 0.47 10V [M]

C7334 ECEA1AKA221I 220 10V [M]

C7335 F1H1C104A008 0.1 16V [M]

C7338 ECJ1VB1C563K 0.056 16V [M]

C7339 ECJ1VB1C183K 0.018 16V [M]

C7352 ECJ1VB1C183K 0.018 16V [M]

C7601 ECEA0JKA330I 33 6.3V [M]

C7613 ECJ1VB1C104K 0.1 16V [M]

C7614 F2A0J101A198 100 6.3V [M]

C7626 ECJ1VB1C104K 0.1 16V [M]

C7670 ECJ1VB1C104K 0.1 16V [M]

SC-EN37P

PRT0703