Panasonic KX-TGA523, KX-TGA523M User Manual

5.8 GHz Expandable Cordless Handset

Operating Instructions

Model No. KX-TGA523

PLEASE READ BEFORE USE AND SAVE.

Charge the battery for 6 hours before initial use.

Pulse-or-tone dialing capability

The KX-TGA523 will only work with the Panasonic cordless phone systems: KX-TG5200/KX-TG5202/ KX-TG5210/KX-TG5212/ KX-TG5230/KX-TG5240/ KX-FPG391

Contents by Section

1 Getting Started 2 Listening to the Radio 3 Using the Sleep Timer 4 Using the Alarms 5 Things You Should Know 6 Referencia rápida

Panasonic World Wide Web address: http://www.panasonic.com

for customers in the USA or Puerto Rico

Attach your purchase receipt here.

For product service

• Visit our website: http://www.panasonic.com/support

• Contact us via the web at: http://www.panasonic.com/contactinfo

• Call us at: 1-800-211-PANA(7262)

When you ship the product

• Carefully pack your unit, preferably in the original carton.

• Attach a letter, detailing the symptom, to the outside of the carton.

Symptom

• Send the unit to an authorized servicenter, prepaid and adequately insured.

• Do not send your unit to the Panasonic Consumer Electronics Company listed below or to executive or regional sales offices. These locations do not repair consumer products.

If you need assistance with the setup or operation, please call 1-800-211-PANA(7262)

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America

One Panasonic Way, Secaucus, New Jersey 07094

Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park Carolina, Puerto Rico 00985

PQQX14029YA S0104-1034

Charge Contacts (1-F)

VOLUME Control (2-A)

[TIME SET] Button (1-H)

[SNOOZE/MUTE] Button (2-D, 4-C)

Memory Buttons ([M1], [M2],

[M3], [M4] and [M5]) (2-B)

[FM/AM, RADIO] Button (2-A)

[SLEEP] Button (3-A)

[OFF] Button (2-A, 4-C)

[+,

, TUNE/CLOCK]

Button (1-H, 2-A)

[BUZZER, ALARM SET] Button (4-B)

[ALARM ON/OFF] Button (4-D)

CHARGE Indicator (1-F)

Display

[RADIO, ALARM SET] Button (4-A)

Headset Jack (5-A)

[Y] (TONE) Button

[ ] (TALK) Button

[ ] (Speakerphone) Button

[

HOLD/INTERCOM]

Button

Charge Contacts (1-F)

Antenna

Display

[OFF] Button

[MENU] Button

[REDIAL] Button

Soft Keys (1-G)

[FLASH/ CALL WAIT]

Button

Navigator Key

Ringer/Message Alert Indicator

Getting Started

1-A Accessories

(included)

Battery ..............................one

Order No. HHR-P104

Handset Cover..................one

Order No. PQKK10142Z1

Belt Clip ............................one

Order No. PQKE10377Z1

Charger Unit .....................one

Charger Order No. KX-TGA523M AC Adaptor Order No. PQLV1Z Loop Antenna Order No.

N1DAEYY00002

1-B Location of Controls

Handset Charger (with Clock Radio)

Note: The steps necessary to start up the

handset are described in these Operating

•

For extra orders, call 1-800-332-5368. For hearing or speech impaired TTY users, call 1-866-605-1277.

Instructions. Please read the KX-TG5200/ KX-TG5202/KX-TG5210/KX-TG5212/ KX-TG5230/KX-TG5240/KX-FPG391 operating instructions for further details about the handset operations.

1-C Connecting the AC Adaptor/Setting Up the Loop Antenna

Stand the antenna up by inserting the tab into the slot until it clicks into place.

•To disconnect the antenna, firmly pull the antenna cord, holding the cord near the plug.

1-D Installing the Handset Battery

Loop Antenna

•USE ONLY WITH Panasonic AC ADAPTOR PQLV1 (Order No. PQLV1Z).

•The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)

1-E Belt Clip

Hook

Hooks

Make sure the AC adaptor plug is securely connected to the unit. Feed the cord through the hooks as shown.

Power Outlet (AC 120 V, 60 Hz)

AC Adaptor

Insert the battery (#), and press it down until it snaps into the compartment ($).

Close the cover.

For assistance, please call: 1-800-211-PANA(7262)

You can hang the handset on your belt or pocket using the included belt clip.

To attach the belt clip To remove the belt clip

While pressing the top of the clip (A), pull the right edge in the direction of the arrow (B).

[OFF]

[+, -, TUNE/CLOCK]

[TIME SET]

Getting Started Section 1

1-F Battery Charge

Place the handset on the charger and charge for 6 hours before initial use.

•The unit beeps once, the CHARGE indicator lights and “Charging” is displayed.

•When the battery is fully charged, “Charge completed” is displayed if there are no

new calls in the Caller List.

CHARGE Indicator

•Recharge the battery when: – “Recharge battery” is displayed on the handset, – “ ” flashes, or – the handset beeps intermittently while it is in use.

•If the battery has been discharged, the handset will display “Charge for 6 HRS” and “ ” when you place the handset on the

charger. The handset will not work unless the battery is charged. Continue charging.

1-G Handset Registration

This handset must be registered to a KX-TG5200/KX-TG5202/ KX-TG5210/KX-TG5212/KX-TG5230/KX-TG5240/KX-FPG391 base unit.

The handset will be assigned an extension number at registration. The KX-TGA523 will not work without one of the following Panasonic cordless phone systems: KX-TG5200/KX-TG5202/KX-TG5210/ KX-TG5212/KX-TG5230/KX-TG5240/KX-FPG391.

[Press LOCATOR on base unit for 3 sec. Then press OK

BACK

CHARGE Indicator

*LOCATOR Button

•Base unit model shown here is KX-TG5240.

Soft Key ( )

*The location of LOCATOR button varies by base unit model.

KX-TG5200/KX-TG5202: LOCATOR [ ], [], [], []or [] KX-TG5210/KX-TG5212: LOCATOR/INTERCOM [ ], [], [],

[]or [] KX-TG5230/KX-TG5240/KX-FPG391: [LOCATOR/INTERCOM/TRANSFER]

]

Battery information

After your Panasonic battery is fully charged, you can expect the following performance:

Operation

While in use (TALK) While not in use (Standby) While using Clarity Booster feature

•Clean the charge contacts of the handset and the charger with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery

may not charge properly.

A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery.

Only one handset can be registered at a time.

Make sure the base unit and the other handsets are not being used. Have both the handset and base unit nearby during registration.

The handset display shows the instructions as shown on the right.

Base unit: Press and hold the

*LOCATOR button for 3 seconds.

The CHARGE indicator flashes. After the CHARGE indicator starts

•

flashing, the rest of the procedure must be completed within 1 minute.

•On the KX-FPG391, “HS REGISTRATION” is displayed.

Handset:

#Press the soft key ( ). $

Wait until a long beep sounds and the display shows the new extension number.

•Registration is complete.

•The registered number “[1]” to “[4]” is shown on the top right of

the display.

•You can stop registration by pressing [OFF] on the handset and pressing the *LOCATOR button on the base unit.

•To cancel the handset’s registration, please see the base unit Operating Instructions.

•If you try to register this handset to the KX-TG6500 base unit, “Wrong handset Refer to manual” is displayed. The base units for this handset are mentioned above.

Operating time

Up to 5 hours Up to 11 days Up to 3 hours

Press LOCATOR on base unit for 3 sec. Then press OK

Ex. Extension number 2

PRIVACY

[2]

Handset [2]

Registered

1-H Setting Time

The charger unit has a 12-hour clock (monthly accuracy ±30 seconds). After the AC adaptor is connected, “ ” flashes on the display. Follow the steps to set the clock.

For assistance, please call: 1-800-211-PANA(7262)

Press [TIME SET].

Adjust the time by pressing

[+, TUNE/CLOCK] or [–, TUNE/CLOCK].

• Pressing [+] or [–] increases or decreases the time in one-minute units.

• Pressing and holding [+] or [–] increases or decreases the time faster.

Press [TIME SET] to set the clock.

• The time stops flashing.

•You can exit time setting mode any time by pressing [OFF].

•If a power failure occurs, the display will show “ ” for about 10

minutes, then it will become blank. After power returns, “ ” will be displayed. The clock memory will be lost. Set the clock. The radio alarm and buzzer alarm memory will be retained for about 10 minutes during a power failure (4-A, 4-B).

Ex. 3:30PM is set.

+ 6 hidden pages