Page 1
Operating Instructions
AC/Rechargeable Professional Hair Clipper
Model No. ER1511
Before operating this unit, please read these instructions completely and save
them for future use.
Page 2
Thank you for choosing a Panasonic Hair Clipper. Please read all
instructions before use.
Important
Before use
This clipper is designed for professional use to trim hair and beards. Charge it
for 8 hours before use for the first time in order to activate the built‑in
rechargeable batteries. It can be operated on either an AC adaptor or
rechargeable batteries. Read all instructions carefully before use.
Charging the clipper
Do not use any power cord or AC adaptor other than this AC adaptor (RE9‑41).
•
Avoid charging the batteries at temperatures below 5 °C or above 35 °C.
•
Avoid charging the batteries in direct sunlight or near a radiating heat source.
•
The charge status ( ) lamp may blink at an early stage when it is used for
•
the first time or if it has not been used for 6 or more months even if it is fully
charged. This is not a malfunction.
Even though the clipper may not be used for an extended period, charge
•
every 6 months to preserve battery life.
The power cord cannot be replaced. If it is damaged, the AC adaptor should
•
be discarded.
Using the clipper
This clipper has a b
•
heat, or charge, use, or leave in a high temperature environment.
Warning ‑ Keep the appliance dry.
•
•
The clipper may become warm during operation and/or charging. This is normal.
•
Check that the blades and the attachments are not damaged before use.
Replace them if they are damaged.
•
Bef
ore each use, apply oil at the places marked with arrows. (See page 8.)
•
You should not allow permanent wave lotion, hair restorer or hair spray to
come into contact with the main body or the blades.
Doing so may result in cracking, discoloring or corrosion.
•
You should not drop the clipper on the floor.
•
You should not knock the blades and the attachments against hard objects.
•
You should not trim the hair of a pet.
Cleaning the clipper
•
Clean the housing using only a cloth slightly dampened with water or a mild
soap solution.
Never use a caustic solution.
•
Never submerge the clipper in water.
•
Storing the clipper
•
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
uilt‑in rechargeable battery. Do not throw into fire, apply
2
Page 3
knowledge, unless they have been given supervision or instruction concerning
3
mm
0/0"
6
mm
0/0"
9
mm
0/0"
12
mm
0/0"
15
mm
0/0"
4
mm
0/0"
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
Never tamper with moving parts.
•
Avoid grabbing the clipper by the power cord, as it may become detached,
•
causing damage or injury.
If the clipper is not working properly, have it inspected at an authorized
•
service center.
Specifications
Power source: See the name plate on the product.
(Automatic voltage conversion)
Motor voltage: 2.4 V DC
Charging time: 1 hour
Parts identification
A Main body
1 T
rimming height indicator
2 Dial (Height adjustment control)
3 P
ower switch [0·CHARGE/1]
4 Batter
y capacity lamp
5 Charge status (
6 Appliance soc
B Blade
7 Mounting hook
ver
ving blade
y blade
mm comb attachment
mm comb attachment
mm comb attachment
8 Cleaning le
9 Mo
Stationar
C 3
D 4
E 6
ket
F 9
mm comb attachment
G 12 mm comb attachment
H 15 mm comb attachment
I AC adaptor (RE9‑41)
) lamp
; Power cord
Appliance plug
J Cleaning brush
K Oil
L Charging stand
Charging plug
Socket
M Comb attachment shelves
(×2)
N Connectors (×2)
3
Page 4
Charge
Charging the hair clipper
Connect the power cord to the
1
1
charging stand.
Slide the power switch to
2
2
“0·CHARGE”.
Plug in the AC adaptor into a
3
3
household outlet and place the
clipper on the charging stand.
Charge status ( ) lamp glows and charging starts.
•
Charging is completed when Charge status ( ) lamp blinks. (Max.
•
1 hour later)
1 full charge will provide approximately 70 minutes of continuous
•
operation.
Connecting the comb attachment shelf to the charging stand
Determine the connection position for the charging
stand and comb attachment shelf. Firmly insert the
connector into the slot at the bottom of the charging
stand.
If the unit wobbles, then further push in the
•
connector since it has not been firmly inserted.
4
Page 5
About the LED display
HIGH
MID
LOW
HIGH
MID
LOW
HIGH
MID
LOW
HIGH
MID
LOW
While charging
glows.
“HIGH”, “MID” or
•
“LOW” blinks.
After charging is
completed
blinks once every
second.
10 minutes after
charging is completed
blinks once every 2
seconds.
“HIGH/MID/LOW” go
•
out.
While using
“HIGH” blinks ‑ The battery capacity is enough.
“MID” blinks ‑ The battery capacity is approx.
60% or less.
“LOW” blinks ‑ The battery capacity is approx.
10% or less.
Charge the clipper when “LOW” starts to blink.•
Charging without the charging stand
1. Slide the po
wer switch to “0·CHARGE”.
2. Plug in the AC adaptor into a household outlet.
3. Insert the appliance plug into the clipper.
AC operation
If you connect the AC adaptor to the clipper in the same way as for charging,
and turn on the power, you can use it even if the battery capacity is low.
If the clipper does not operate, charge the clipper for approximately
•
1 minute.
Be careful not to discharge the battery completely with the power left turned
•
on. It results in shortening the battery life.
5
Page 6
Cut
0.8
Using the hair clipper
Turn the dial clockwise or counterclockwise to adjust the moving
blade back and forth to get the desired height. Adjustable in
5 stages from 0.8 mm to 2.0 mm in 0.3 mm steps without
attachments.
The actual cut length may be longer than the set length.
Using the comb attachments
1. Select the trimming heights indicated on the insides
and sides of the attachments.
Set the dial to “0.8” and then mount the attachment to
2
the clipper as illustrated.
Removing the attachment from the clipper
Remove the attachment as illustrated.
6
Page 7
Care
2.0
Blade maintenance
Removing and mounting the blade
Removing the blade
1. Hold the clipper with the switch facing
upward and push the blade with your
thumb while catching the blade in your
other hand.
Be sure to turn off the power before you
•
remove the blade.
Mounting the blade
1. Set the dial to “2.0”.
2. Fit the mounting hook into the
blade mounting on the clipper
and push in until it clicks.
7
Page 8
Cleaning the blade
1. Brush off any
hairs from the
clipper and
from around
the blade.
2. Remove the
blade and brush
off the hairs
from the blade
edge.
Lubrication
1. Apply a few drops of the oil to the
space between the stationary blade
and moving blade.
Apply the oil to the clipper before and
•
after each use.
2. Set the dial to “2.0” and then
remount the blade on the clipper.
3. Brush the hairs out from
between the stationary
blade and the moving blade
while pressing down on the
cleaning lever to raise the
moving blade.
8
Page 9
Removing the built‑in rechargeable batteries
1. Remove the blades 1 and four screws 2.
2. Remove the spring 3, the under cover 4, and the blade holder 5.
3. Remove the dial 6 and open the housing 7, and then take out two
batteries 8.
•
Disconnect the clipper from a household outlet.
•
Discharge the batteries completely before removing them.
•
Be careful not to short‑circuit the batteries.
WARNING ‑ Do not attempt to replace the batteries for the purpose of
reusing the clipper. This could result in the risk of fire or electric shock.
Important notice regarding environmental protection
The built‑in rechargeable Nickel‑Metal Hydride batteries contain substances
that may be environmentally harmful. Please remove the batteries before
discarding your clipper.
For environmental protection and recycling materials
This clipper contains Nickel‑Metal Hydride batteries.
Please make sure that the batteries are disposed of at an officially assigned
location, if there is one in your country.
9
Page 10
Panasonic Electric Works Co., Ltd.
http://panasonic.net
F EN
Printed in Japan
ER971015111H Y0710‑0
Loading...