Omnicell Supply Mobile Cart, Half Cell User manual

Supply Mobile Cart / Half Cell Installation and Service Guide

67-2043 Rev B

This guide is CONFIDENTIAL and designed only for Omnicell Technical personnel and/or designated representatives.

This guide and accompanying software and/or hardware described in it are protected under copyright laws and may not be copied, wholly or in part, without the express written consent of Omnicell, Inc. The same proprietary and copyright notices must be attached to any permitted copies as were attached to the original documents.

Omnicell, Inc. 1201 Charleston Road Mountain View, CA 94043 (650) 251-6100 www.omnicell.com

Omnicell and the Omnicell design mark, OmniBuyer, OmniCenter, OmniRx, OmniSupplier, SafetyMed, SafetyPak, SafetyStock, and Sure-Med are registered trademarks. Anesthesia TT, Anesthesia Workstation, Anywhere RN, Executive Advisor, Flexbin, Medication Surveillance, OmniDispenser, OmniLinkRx, OmniScanner, OmniTrack, Omni TT, Open Touch, OptiFlex, OptiFlex MobileTrack, Point-to-Point Medication Safety, SecureVault, See & Touch, SinglePointe, TempCheck, Touch & Go, VSuite, and WorkflowRx are trademarks of Omnicell, Inc. in the United States and internationally. All other trademarks and trade names are the property of their respective owners.

Table of Contents

Electronics Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Shutdown Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

CT PC Tray Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

PowerCom2 Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

PowerCom3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15

Standardization Changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19

System Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20

iii

Frames and Wireways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Shutdown Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Wireway Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

System Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Shelves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Shutdown Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Shelf Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Divider Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Shelf Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Divider Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Pull-out Shelf Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

System Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Switchpanels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Shutdown Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Switchpanel Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Shelf Switchpanel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Supply Drawer Switchpanel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Pull-out Shelf Switchpanel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

System Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

iv Table of Contents

Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Door Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Door Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Bin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Pharmacy Drawer Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

System Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Half Cell Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

One-Third Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Supply Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Pharmacy Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Unlit Matrix Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Lit Matrix Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Matrix Drawers Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

Shutdown Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Double-Deep Matrix Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Supply Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Pharmacy Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

Appendix A: Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IN-1

Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FB-1

Electronics Tray

Note:

cart has casters that allows the cabinet to be moved easier.

Introduction

This chapter provides instructions to properly remove specific parts within the Color Touch (CT) PC sled (electronics tray). Parts are replaced by generally performing the removal procedures in reverse. Follow the shutdown procedure before attempting any service on the cabinet. Perform the restart steps after the service is completed.

Tools List

1-1

The half cell and supply mobile cart are similar cabinets. The main difference is that the supply mobile

The following tools are required to install the electronics tray:



T8 Torx Driver



T10 Torx Driver



T15 Torx Driver



9/64” Allen wrench



USB B to A (male to male) cable



Hyperterminal



Needle nose pliers



5/16" nut driver



Medium size (#8 - 8/32) Phillips screwdriver



Voltmeter/ multimeter

Shutdown Procedures

1. Perform a graceful shutdown of the electronics tray.

2. Unplug the cabinet from its power source.

3. Employ ESD protection before working in the electronics sled.

1-2 Electronics Tray

LCD Assembly

1. Unlock the lid with key #2036, then open and prop up the lid.

2. Disconnect the video image cable.

Figure 1-1. Disconnect the video image cable.

3. Disconnect the touch screen cable.

Figure 1-2. Disconnect the touch screen cable

4. Disconnect the backlight cable.

Figure 1-3. Disconnect the backlight cable

Electronics Tray 1-3

LCD Assembly

5. Set the lid back down.

6. Remove the four outer screws that secure the LCD bezel to the half cell using a Torx T10 screwdriver.

Figure 1-4. Remove the four outer screws

1-4 Electronics Tray

LCD Assembly

7. Remove the front bezel.

Figure 1-5. Remove the front bezel

8. Remove the four inner screws at the back of the console lid.

Note: Hold onto the front of the LCD screen while removing the screws so that the assembly does not fall.

Figure 1-6. Remove the four inner screws

Electronics Tray 1-5

9. Tilt the LCD assembly forward and pull the cables through the opening in the lid.

Figure 1-7. Remove the cables from the opening in the lid

Speaker

10. Remove the LCD assembly from the LCD housing.

1. Unlock the lid with key #2036, then open and prop up the lid.

2. Disconnect the speaker cable from the motherboard.

Figure 1-8. Disconnect the speaker cable from the motherboard

1-6 Electronics Tray

Batteries

3. Remove the two screws that hold the speaker in place using a Torx T10 screwdriver.

Figure 1-9. Remove the two screws that secure the speaker

Batteries

4. Remove the speaker from the console top.

The supply mobile cart comes with optional batteries.

1. Unlock the lid with key #2036, then open and prop up the lid.

2. Remove the thumb screws that secure the metal cover for the lithium ion batteries.

Figure 1-10. Remove the thumb screws

3. Slide the cover to the left, away from the motherboard.

Figure 1-11. Slide the battery cover

Electronics Tray 1-7

Batteries

4. Lift the cover and remove it from the sled.

Figure 1-12. Lift and remove the battery cover

1-8 Electronics Tray

Batteries

5. Lift the batteries and move them off the stand.

Figure 1-13. Lift the batteries off the stand

6. Disconnect the front battery cable from the motherboard.

Figure 1-14. Disconnect the battery cable

7. Remove the cable from the hole of the battery support frame.

Figure 1-15. Remove the battery cable

Electronics Tray 1-9

Batteries

8. Remove the three screws that secure the battery frame to the sled.

Figure 1-16. Remove the screws that secure the battery frame

9. Remove the battery frame.

a. Lift the frame up and over the screws.

b. Slide the frame toward the front of the sled to remove it.

1-10 Electronics Tray

Printer

1. Open the printer cover by pushing the black release lever up, then lifting the cover.

Figure 1-17. Open the printer cover

2. Push the platen lever to the left (counter clockwise) to set it to the disengage position.

3. Remove the paper from the printer.

Figure 1-18. Push the platen lever to the left and remove the paper

Electronics Tray 1-11

Printer

4. Remove the four screws (two on each side) that secure the printer assembly to the cover.

Figure 1-19. Remove the screws securing the printer assembly

5. Remove the printer assembly.

6. Remove the four screws that secure the lower assembly to the frame.

Figure 1-20. Remove the screws that secure the lower assembly

1-12 Electronics Tray

Printer

7. Disconnect the printer ribbon cable and the printer data cables from the printer PC Board.

Figure 1-21. Remove the printer ribbon cable and the printer data cable

8. Remove the printer.

Figure 1-22. Remove the printer

9. Remove the four screws that secure the PC card to the frame.

Figure 1-23. Remove the screws that secure the printer PC card

Electronics Tray 1-13

CT PC Tray Upgrade

10. Lift the card off the frame slightly, then remove the printer PC card.

CT PC Tray Upgrade

PowerCom2 Removal

1. Disconnect the LAN cable and the AUX cables from the rear of the CT PC Box.

Figure 1-24. Location and labels for LAN and AUX cable connections on CT PC Tray

2. Unlock the lid with key #2036, then open and prop up the lid.

1-14 Electronics Tray

CT PC Tray Upgrade

3. Disconnect the following cables from the tray. Match the letters from the list to the ones in Figure 1-18 for orientation.

a. LCD data cable

b. Contrast cable

c. Inverter (backlight) cable

d. Touch screen data cable

e. Keyboard cable

f. Speaker cable

g. Card reader cable (if applicable–not shown)

h. Fan power cable (if applicable)

i. Printer cable (free cable from any clips)

j. Cabinet power/comm cable

Figure 1-25. Location of cables on the CT PC Tray with PowerCom2 Board

+ 42 hidden pages