Page 1
CONFIDENTIAL 1 (5)
Nokia Mobile Phones Service Bulletin No. SB-047/04.12.00
Technical Support, Europe & Africa
NSE-8
VIBRA MOTOR FOR NSE-8
NSE-8 phones have no vibra motor (vibrator) installed when sold, but now it
is possible for customer to get it with extra fee. This possibility to install
vibrator later concerns only NSE-8 phone models!
Note 1: In the future before updating the software in any NSE-8 phones, the
phone should be examined, if a vibrator has been previously installed or not
(please ref section 3. Updating the software in a NSE-8 phone where a
vibrator has previously been installed)
Note 2: When ordering the vibra motor as a spare part only the following
code should be used.
CODE DESCRIPTION
6800039 VIB.MOTOR ASSY 1.3V 100MA 7300RPM
The part includes a motor with spring contacts, a counterweight mounted on
the motor axle and a vibra-boot with a mounting hole. All joined together as
one whole unit .
Motor with spring contacts
Vibra-boot (rubber)
Counterweight
Mounting hole
NSE-8 SB-047
Page 2
CONFIDENTIAL 2 (5)
1) Installing the vibrator and configure the phone software to enable the
vibrator.
Mechanical installation
• Remove A- and B-cover and
battery.
• Remove SIM card.
• Remove antenna.
• Unscrew D-cover (metal cover),
remove it and lay it as shown in
the picture.
• Place the Vibrator as shown with
the spring contacts up,
counterweight to the left and the
mounting hole in the green vibraboot on the tap in the D-cover.
(see picture)
• Press the vibrator gently down to
mount it in the D-cover. When
done, turn D-cover and verify that
the vibrator is stuck in the Dcover.
• Gently put the D-cover on top of
the PCB and screw the parts
together. Screw torque should be
30 Ncm.
• Mount the antenna and the Acover.
Software settings
The following procedure will enable the Vibrating alert menu.
• In WinTesla, enter the
Product Profile window from
the Software menu.
• Change the Vibrator setting
from Not in Menu to
In menu.
• Click Save
• Press F5 to reset the phone
and thus reload the saved
Product Profile
NSE-8 SB-047
Page 3
CONFIDENTIAL 3 (5)
The vibrator is now installed and the
Vibrating alert menu is enabled. This can
be verified by entering the Vibrating alert
menu (menu 9-8) and confirming that the
setting is On. (see picture)
To verify that the vibrator is functioning,
enter the Ringing tone menu (Menu 9-2)
and browse to another ringing tone. When
the ringing tone is played, the phone
should vibrate as well.
2) Updating the software to NSE-8 phone without vibrator.
Preliminary examination
• Before updating a NSE-8
with a new software, it
should be examined to find
out, if the phone has a
vibrator installed. By looking
into the small gap in the Dcover, it is possible to see if
a vibrator is present.
• If NO vibrator is present, a
small part of the PCB is
seen, especially the two
contact points where the
vibrator make electrical
contact.
Gap
NSE-8 SB-047
In this case software
updating can be done as
usually without any
consideration to the vibrator
software settings.
PCB with
contact points
Page 4
CONFIDENTIAL 4 (5)
Motor
• It can be difficult to see the
vibrator, but it should be
possible to see the end of
the motor which is black, and
part of the green vibra-boot.
If a vibrator is present, the
software should be updated
as described in the next
section 3 "Updating the
software in an NSE-8 phone
where a vibrator has
previously been installed."
3) Updating the software in an NSE-8 phone where a vibrator has
previously been installed.
Vibra-boot
Special care must be taken when updating the software to a phone where
the vibrator has previously been installed. If these instructions are not
followed, there is a risk that the vibrator menu will be disabled after software
update.
• In WinTesla, enter the Flash
window from the Dealer
menu.
• Select the right software
version and market area and
click Flash.
• You are then asked, if you
want to save the user
settings. Click Yes.
• You are then asked, where
you want to save the
temporary file containing the
user settings. Just click OK.
NSE-8 SB-047
Page 5
When flashing is completed the
Vibrating alert menu is still
enabled. This can be verified by
entering the Vibration alert
menu (menu 9-8) and
confirming that the setting is On.
To verify that the vibrator is
functioning, enter the Ringing
tone menu (Menu 9-2) and
browse to another ringing tone.
When the ringing tone is played,
the phone should vibrate as well
Manual setting
• If the User Settings were not
saved before flashing, there
will be a prompt for restoring
the default User Settings.
Click OK to this prompt (do
NOT click Cancel).
This will disable the Vibrating
alert menu, which means
that the Vibrating alert menu
must be enabled again.
CONFIDENTIAL 5 (5)
• This can be done by
following the description in
the section: "Installing the
vibrator and configure the
phone software to enable the
vibrator" (Software settings).
Depending on the Market Area the active
checkboxes may vary.
NSE-8 SB-047
Loading...