New Holland Haybine 472, Haybine 499, Haybine 488 User Manual

New Holland

Haybine

472 488 499

MODEL 472 488 499

UTTERBAR WIDTH, ft. in. (mm) 7’3” (2210) 9’3” (2819) 12’3” (3734)

OVERALL WIDTH

Operating, ft. in. (mm) 11’11” (3632) 13’8-1⁄4” (4172) 19’8” (5994) Transport, ft. in. (mm) 10’4-3⁄4”(3168) 12’2” (3708) 13’9” (4191)

OVERALL LENGTH

Operating, ft. in. (mm) 13’1” (3988) 13’4” (4064) 16’8” (5080) Transport, ft. in. (mm) 13’1” (3988) 13’4” (4064) 21’6” (6553)

HEIGHT

Operating, ft. in. (mm) 3’5-3⁄4” (1060) 3’6” (1067) 6’2-1⁄2” (1892) Raised, ft. in. (mm) 4’8” (1422) 5’7” (1702) 6’8-1⁄2” (2045)

WEIGHT, lbs. (kg) 2110 (957) 2763 (1253) 4480 (2032)

Mower-Conditioner Specifications

DRIVE 540 rpm PTO 540 rpm PTO 540 or 1000 rpm PTO

TRACTOR REQUIREMENT 30-hp (22.4 kw) or greater 35-hp (26.1 kw) or greater 60-hp (45 kw) or greater with

with standard ASAE hitch with standard ASAE hitch standard ASAE hitch and PTO and PTO locations and PTO locations locations.

HEADER FLOTATION Full, lateral Full, lateral Full, lateral, independent

HEADER LIFT

Guard points maximum lift, in. (mm) 18-1⁄2 (470) 19 (483) 19-1⁄2 (495)

REEL 4-tine bar 4-tine bar Rolareel Peripheral speed, mph (kph) 6.2 to 8.2 (10.4 to 13.2) 6.5 to 8.6 (10.5 to 13.8) standard—4.8 to 7.9

Diameter (maximum), ft. in. (mm) 3’6-1⁄4” (1073) 3’6-1⁄4” (1073) 3’7-1⁄2” (1105)

CUTTERBAR

Knives Bolted, over-serrated Bolted, over-serrated Two opposing assemblies —

sections sections bolted over-serrated sections,

Guards Twin-forged steel, double- Twin-forged steel, double- Twin-forged steel, double-

hardened or stub guards hardened or stub guards hardened or stub guards

Cutting height, in. (mm) Adjustable from 1-1⁄4 to 4-1⁄4 Adjustable from 1-1⁄4 to 4-1⁄4 Adjustable from 1-1⁄4 to 6-1⁄4

(32 to 108) (32 to 108) (32 to 159)

hydrostatic system

Two remote hydraulic systems required capable of 1750 psi (12066 kpa).

of conditioning rolls

(7.7 to 12.7) with reduction kit—4.0 to 6.6 (6.5 to 10.7)

adjustable hold-downs

SICKLE DRIVE wobble joint wobble joint enclosed gearbox Speed, spm 1632 1632 1700 Stroke, in. (mm) 3 (76) 3 (76) 3 (76)

Page 1 of 2

New Holland

Haybine

472 488 499

MODEL 472 488 499

ONDITIONER Chevron-design intermeshing Chevron-design intermeshing Chevron-design intermeshing

Roll length (crushing area), in. (mm) 85 (2159) 102 (2591) 110 (2794) Roll diameter, in. (mm) 7-3⁄4 (199) 10-3⁄8 (264) 10-3⁄8 (264) Drives Individual, #50 roller chain Individual, #50 roller chain Gear/shaft Speed, rpm 818 637 665 Pressure, lbs./in. (N/mm) 2 to 38 of roll length 2 to 38 of roll length 2 to 38 of roll length

Material discharge, in. (mm) Adjustable gate for swath, Adjustable gate for swath, Adjustable gate for swath,

OPERATING SPEED, mph (kph) up to 8 (13) up to 8 (13) up to 8 (13) Maximum safe transport speed,

mph (kph) 25 (40) 25 (40) 25 (40)

Mower-Conditioner Specifications

rubber rolls rubber rolls rubber rolls

(0.3 to 6.6) (0.3 to 6.6) (0.3 to 6.6)

windrow or intermediate widths. windrow or intermediate widths. windrow or intermediate widths. Infinitely variable between Infinitely variable between 11 settings between 38 (965) and 72 (1829) 38 (965) and 96 (2438) 38 (965) and 100 (2540)

TIRES 25 x 7.50-15 flotation 27 x 9.50-15 flotation 11L x 14 4-ply agricultural

HYDRAULIC CYLINDERS Optional header lift Optional header lift Standard header lift

OPTIONAL EQUIPMENT:

• Standard or stub guards (472, 488)

• Crop dividers (right-hand standard; left-hand optional on 472, 488)

• Push-bar extension (472, 488)

• Hydraulic lift kit (standard on 499)

• Reel speed reduction kit (499)

• Hydraulic guard angle adjustment kit (499 only)

• Spare-knife holder kit (standard on 499)

• Center skid shoe kit (499 only)

• Safety tow chain

• Knife assembly storage (std on 499, OPT on 472, 488)

implement (HUT)

Standard tongue shift

Visit our Web site at www.newholland.com/na. Or, call toll-free 866-NEW-HLND (866-639-4563).

Design, mat erials and/or specific ations are subject to chan ge wi thout noti ce an d with out l iabilit y the refor. Specificat ions are applicable to units sold in Canada, the United Stat es, its territori es and possessions, and may var y outsi de these areas.

Safety begins with a thorough understanding of

the equipment. Always make sure you and

your operators read the Operator’s Manual

before using the equipment. Pay close

attention to all safety and operating

decals and never operate machinery

without all shields, protective devices

and structures in place.

Page 2 of 2