New Holland 918L, 918H User Manual

New Holland Flail Mower Specifications

918H 918L

MODEL 918H 918H 918H

IZE 60-inch 71-inch 91-inch

PTO hp rating............................................................................................................................................................70...............................................................................................

Rated speed (rpm)...................................................................................................................................................540..............................................................................................

Nominal cutting width, in. (mm) 60 (1524.0) 71 (1803.4) 88 (2235.2) Offset adjustment to right, in. (mm) 28 (711.2) 28 (711.2) 24 (609.6) Offset adjustment to left, in. (mm) n/a 46 Cutting height range, in. (mm) 0.5 to 5 (13 to 127) 0.5 to 5 (13 to 127) 0.8 to 5 (19 to 127)

Cutting height adjustment increments, in. (mm).................................................................................................1 (25.4) ..........................................................................................

Rotor diameter, tip-to-tip, in. (mm) 15.8 (401.32) 15.8 (401.32) 16.50 (419.1)

Rotor rotation.................................................................................................................................................forward/reverse....................................................................................

Guage roller diameter, in. (mm) ........................................................................................................................5.2 (132.1)........................................................................................

Blade mounting.................................................................................................................................................single hinge .......................................................................................

Blade type ............................................................................................................................................................standard..........................................................................................

Number of blades 80 96 128 Blade tip speed (fpm) 9237 9237 9659

Rotor shaft speed (rpm).........................................................................................................................................2236.............................................................................................

Thickness of flail deck, in. (mm) ........................................................................................................................0.16 (4.0).........................................................................................

Thickness of flail ends, in. (mm)........................................................................................................................0.24 (6.0).........................................................................................

Lift linkage.............................................................................................................................................................flexible...........................................................................................

Three-point hitch category.....................................................................................................................................I or II ............................................................................................

Weight, lbs. (kg) 697 (316.2) 792 (359.3) 957 (434.1)

MODEL 918L 918L SIZE 50-inch 60-inch

PTO hp rating ...........................................................................................................................30...............................................................................................................................

Rated speed (rpm)..................................................................................................................540..............................................................................................................................

Nominal cutting width, in. (mm) 50 (1270) 60 (1524) Offset adjustment to right, in. (mm) 10 (254) 20 (508)

Offset adjustment to left, in. (mm) ..........................................................................................n/a...............................................................................................................................

Cutting height range, in. (mm)...................................................................................0.75 to 3 (19 to 76).................................................................................................................

Cutting height adjustment increments, in. (mm)..............................................................0.75 (19.1) ........................................................................................................................

Rotor diameter, tip-to-tip, in. (mm) .................................................................................13.5 (342.9).......................................................................................................................

Rotor rotation .......................................................................................................................reverse...........................................................................................................................

Guage roller diameter, in. (mm).........................................................................................3.5 (88.9).........................................................................................................................

Blade mounting.................................................................................................................single hinge .......................................................................................................................

Blade type................................................................................................................................fine ..............................................................................................................................

Number of blades 80 96

Blade tip speed (fpm) ............................................................................................................7,522.............................................................................................................................

Rotor shaft speed (rpm) ........................................................................................................2,137.............................................................................................................................

Thickness of flail deck, in. (mm).........................................................................................0.1 (2.5)..........................................................................................................................

Thickness of flail ends, in. (mm).........................................................................................0.2 (5.0)..........................................................................................................................

Lift linkage..............................................................................................................................fixed .............................................................................................................................

Three-point hitch category........................................................................................................ I................................................................................................................................

Weight, lbs. (kg) 348 (157.9) 383 (173.7)

Visit our Web site at www.newholland.com/na. Or, call toll-free 866-NEW-HLND (866-639-4563).

Design, materials and/o r sp ecifications ar e s ubject to chan ge withou t no tice and wit hout liab ility the refor. Specificat ions are applicable to units sold in Canada, the United Stat es, its territ ories and possessi ons, and may var y o utside these are as.

Safety begins with a thorough understanding of

the equipment. Always make sure you and

your operators read the Operator’s Manual

before using the equipment. Pay close

attention to all safety and operating

decals and never operate machinery

without all shields, protective devices

and structures in place.

Page 1 of 1