N122WG
1/4” STICK ON, BREAKOFF FLANGE, CENTER LEADS
DESCRIPTION
Nascom’s N122WG Series, 1/4” stick on contact, protects all nonferrous (e.g. wood, aluminum and vinyl) doors and windows, in both residential and commercial settings.
The N122WG is the installer’s choice of contact configuration where excellent air and side-to-side gap are required to prevent false alarms caused by shifting or warping doors and windows.
FEATURES
• BREAKOFF FLANGE |
• ENCAPSULATED HERMETICALLY SEALED CONTACTS |
• 12” 22AWG WIRE LEADS |
• 3M VHB (Very High Bond) DOUBLE SIDED TAPE |
• WIDE GAP - N35 NdFeB RARE EARTH MAGNET |
• ABS HOUSINGS |
• LISTED TO UL634 STANDARD |
|
ORDERING INFORMATION
|
|
OPERATE |
|
CONTACT RATING |
|
STATIC |
||
|
|
(Max DC/Peak AC Resistive) |
||||||
PART |
|
CONTACT |
||||||
COLOR |
GAP |
|
|
|
|
|||
NUMBER |
SWITCHING |
CARRY |
RESISTANCE |
|||||
|
(in inches) |
|||||||
|
|
V |
I |
V |
I |
(50mV, 100mA) |
||
|
|
|
||||||
|
|
|
|
|||||
CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET: |
|
|
||||||
N122WGSW/ST |
SNOW WHITE |
|
|
|
|
|
|
|
N122WGB/ST |
BROWN |
|
|
|
|
|
|
|
N122WGG/ST |
GREY |
0.75 to 1.125 |
200 VDC |
0.5 Amps |
10vA |
1.5 Amps |
150 mOhms |
|
N122WGT/ST |
TAN |
|
|
|
|
|
|
|
N122WGW/ST |
WHITE |
|
|
|
|
|
|
|
OPEN LOOP, NORMALLY CLOSED, 1FB, SWITCH/MAGNET SET: |
|
|
|
|||||
N122WGSW/STFB |
SNOW WHITE |
|
|
|
|
|
|
|
N122WGB/STFB |
BROWN |
|
30 VDC |
0.2 Amps |
3vA |
0.5 Amps |
100 mOhms |
|
N122WGG/STFB |
GREY |
0.65 to 1.00 |
||||||
N122WGT/STFB |
TAN |
|
|
|
|
|
|
|
N122WGW/STFB |
WHITE |
|
|
|
|
|
|
DWG No. 131118-01 Rev. 1
Royne Industries LLC, dba NASCOM | P: 800.843.5530 | F: 800.727.4041 | www.nascominc.com |
1 |
N122WG
1/4” STICK ON, BREAKOFF FLANGE, CENTER LEADS
WIRING SCHEMATIC
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SWITCH |
|
|
SWITCH |
|||||
|
CONTACT |
|
|
CONTACT |
|||||
|
|
|
|
|
|
|
|
|
|
|
CLOSED LOOP, |
|
|
|
OPEN LOOP, |
||||
|
NORMALLY OPEN CONTACT |
|
|
NORMALLY CLOSED CONTACT |
|||||
|
|
|
|
|
|
|
|
|
|
DIMENSIONS - IN [mm] |
|
|
|
|
||
|
|
1.025 |
|
|
1.025 |
|
|
|
26.04 |
|
|
26.04 |
.262 |
|
|
|
|
|
|
|
|
|
|
|
|
|
6.65 |
|
|
.262 |
|
|
1.332 |
|
|
|
6.65 |
|
|
|
|
|
|
|
|
|
33.83 |
|
|
1.332 |
|
|
|
TOP VIEW |
|
|
|
|
|
|
|
|
|
33.83 |
|
|
|
|
|
|
TOP VIEW |
|
11.250 |
.350 |
|
.300 |
.350 |
|
.300 |
285.75 |
8.89 |
|
7.62 |
8.89 |
|
7.62 |
|
|
|
|
|
|
|
.500 |
|
|
.500 |
3M TAPE |
FRONT VIEW |
|
12.70 |
3M TAPE |
FRONT VIEW |
12.70 |
|
|
END VIEW |
|
END VIEW |
||
|
|
|
|
|
||
|
|
SWITCH |
|
|
MAGNET |
|
INSTALLATION INSTRUCTIONS
•Pre-fit the switch and magnet in the desired location on the window.
•Clean the mounting surface area for both switch and magnet with alcohol and let dry.
•Remove the liner from the tape on the back of the switch and carefully position the switch on the window frame as close as possible to the movable part of the window.
•Remove the liner from the tape on the back of the magnet and carefully align the magnet parallel with the switch on the movable part of the window and as close to the window frame as possible.
•Apply firm pressure to the switch and magnet housing to ensure proper adhesion to the mounting surface.
•Connect the switch leads to the alarm system circuit. Caution! Hold wire leads, not the switch housing while cutting and stripping to prevent damage to switch.
•Test alarm system for correct operation.
DWG No. 131118-01 Rev. 1
Royne Industries LLC, dba NASCOM | P: 800.843.5530 | F: 800.727.4041 | www.nascominc.com |
2 |