Nascom N135WGG-SW-CAPC, N135WGW-SW-CAPC, N135WGW-ST-CAPC, N135WGT-SW-CAPC, N135WGT-ST-CAPC Specsheet

...
Nascom N135WGG-SW-CAPC, N135WGW-SW-CAPC, N135WGW-ST-CAPC, N135WGT-SW-CAPC, N135WGT-ST-CAPC Specsheet

N135WG CAP C

STICK ON CAPSULE SWITCH AND MAGNET SET WITH CENTER LEADS

DESCRIPTION

Nascom’s N135WG CAP C Series is our ground breaking CAP switch. Never drill in windows or doors again. The switch and magnet are so thin they will fit between the window sill and sash. When surface mounted, the smooth rounded edges and ultra-thin profile makes it almost disappear. The CAP switch is designed to protect all nonferrous (e.g. wood, aluminum and vinyl) doors and windows, in both residential and commercial settings.

The N135WG CAP C, is the installer’s choice of contact configuration where surface mount is required excellent air and side-to-side gaps are required to prevent false alarms caused by shifting or warping doors and windows.

FEATURES

EURO DESIGN - ALMOST DISAPPEARS

3M VHB (Very High Bond) DOUBLE SIDED TAPE

12” 24AWG ZIPCORD LEADS

ABS HOUSINGS

WIDE GAP - N35 NdFeB RARE EARTH

 

ORDERING INFORMATION

 

 

OPERATE

 

CONTACT RATING

 

STATIC

 

 

(Max DC/Peak AC Resistive)

PART

 

CONTACT

COLOR

GAP

 

 

 

 

NUMBER

SWITCHING

CARRY

RESISTANCE

 

(in inches)

 

 

V

I

V

I

(50mV, 100mA)

 

 

 

 

 

 

 

CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET:

 

 

 

N135WGB/ST CAPC

BROWN

 

 

 

 

 

 

N135WGG/ST CAPC

GREY

0.50 to 0.875

200 VDC

0.5 Amps

10vA

1.5 Amps

150 mOhms

N135WGT/ST CAPC

TAN

 

 

 

 

 

 

N135WGW/ST CAPC

WHITE

 

 

 

 

 

 

WIRING SCHEMATIC

SWITCH

CONTACT

CLOSED LOOP,

NORMALLY OPEN CONTACT

DWG No. 131123-17 Rev. 1

Royne Industries LLC, dba NASCOM | P: 800.843.5530 | F: 800.727.4041 | www.nascominc.com

1

 

 

N135WG CAP C

 

 

STICK ON CAPSULE SWITCH AND MAGNET SET WITH CENTER LEADS

DIMENSIONS - IN [mm]

 

 

.335

 

 

8.51

 

 

 

 

.168

11.00

 

4.25

 

 

279.40

 

 

 

 

3M VHB TAPE

.168

 

.015

6.99

0.38

4.25

.275

 

 

 

3M VHB TAPE

 

 

SWITCH

 

MAGNET

INSTALLATION INSTRUCTIONS

Pre-fit the switch and magnet in the desired location on the window.

Clean the mounting surface area for both switch and magnet with alcohol and let dry.

Remove the liner from the tape on the back of the switch and carefully position the switch on the window frame as close as possible to the movable part of the window.

Remove the liner from the tape on the back of the magnet and carefully align the magnet parallel with the switch on the movable part of the window and as close to the window frame as possible.

Apply firm pressure to the switch and magnet housing to ensure proper adhesion to the mounting surface.

Connect the switch leads to the alarm system circuit. Caution! Hold wire leads, not the switch housing while cutting and stripping to prevent damage to switch.

Test alarm system for correct operation.

PART NUMBERING SYSTEM

 

 

 

N135WG

X

/

ST

XXXX

 

CAPC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COLOR:

 

 

 

 

 

 

 

 

 

 

 

LEAD LENGTH (zero, 3 or 4 digits):

B = BROWN

 

 

 

 

 

 

 

 

 

 

 

• Blank - 12 Inches

G = GREY

 

 

 

 

 

 

 

 

 

 

 

• All other lengths specified in Inches with 3

 

 

 

 

 

 

 

 

 

 

 

T = TAN

 

 

 

 

 

 

 

 

 

 

 

digits (e.g. 036 = 36 Inches)

W = WHITE

 

 

 

 

 

 

 

 

 

 

 

 

DWG No. 131123-17 Rev. 1

Royne Industries LLC, dba NASCOM | P: 800.843.5530 | F: 800.727.4041 | www.nascominc.com

2

Loading...