Nascom N1175600G-ST, N1175600W-STFB, N1175600W-ST2CR, N1175600W-ST, N1175600T-STFB Specsheet
...
N1175 600
3/8” RECESSED MINI CONTACT WITH NdFeB 0.600” DOUGHNUT MAGNET
DESCRIPTION
Nascom’s N1175 600 Series, mini 3/8” recessed contact with an NdFeB 0.600” doughnut magnet, protects all nonferrous (e.g. wood, aluminum and vinyl) doors and windows, in both residential and commercial settings.
The N1175 600 is the installer’s choice of contact configuration where drill depth is critical and excellent air and side-to-side gap are required to prevent false alarms caused by shifting or warping doors and windows due.
FEATURES
• PRESS FIT - NO GLUE REQUIRED |
• ENCAPSULATED HERMETICALLY SEALED CONTACTS |
• 12” 22AWG WIRE LEADS |
• POLYPROPYLENE HOUSINGS |
• WIDE GAP - N35 NdFeB RARE EARTH MAGNET |
• LISTED TO UL634 STANDARD |
ORDERING INFORMATION
|
|
OPERATE |
|
CONTACT RATING |
|
STATIC |
||
|
|
(Max DC/Peak AC Resistive) |
||||||
PART |
|
CONTACT |
||||||
COLOR |
GAP |
|
|
|
|
|||
NUMBER |
SWITCHING |
CARRY |
RESISTANCE |
|||||
|
(in inches) |
|||||||
|
|
V |
I |
V |
I |
(50mV, 100mA) |
||
|
|
|
||||||
|
|
|
|
|||||
CLOSED LOOP, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET: |
|
|
|
|||||
N1175600B/ST |
BROWN |
|
|
|
|
|
|
|
N1175600G/ST |
GREY |
0.75 to 1.125 |
200 VDC |
0.5 Amps |
10vA |
1.5 Amps |
150 mOhms |
|
N1175600W/ST |
WHIITE |
|
|
|
|
|
|
|
HIGH SECURITY, NORMALLY OPEN, 1FA, SWITCH/MAGNET SET: |
|
|
|
|||||
N1175600B/STHS |
BROWN |
|
|
0.20 |
|
|
150 mOhms |
|
N1175600G/STHS |
GREY |
0.1875 to 0.50 |
300 VDC |
3vA |
0.5 Amps |
|||
Amps |
initial |
|||||||
N1175600W/STHS |
WHIITE |
|
|
|
|
|||
|
|
|
|
|
|
|||
WIRING SCHEMATIC
SWITCH
CONTACT
CLOSED LOOP,
NORMALLY OPEN CONTACT
DWG No. 131119-07 Rev. 1
Royne Industries LLC, dba NASCOM | P: 800.843.5530 | F: 800.727.4041 | www.nascominc.com |
1 |
|
|
|
N1175 600 |
|
|
|
3/8” RECESSED MINI CONTACT WITH NdFeB 0.600” DOUGHNUT MAGNET |
||
DIMENSIONS - IN [mm] |
|
|
|
|
|
.465 |
|
|
|
TOP |
11.81 |
|
|
|
|
|
|
|
|
VIEW |
.355 |
A |
|
.125 |
|
.300 x 82 |
|||
|
|
|
|
|
|
9.02 |
|
|
R.010 TYP ALL EDGES |
|
|
|
|
|
|
|
|
82.00° |
|
FRONT |
.680 |
|
.125 |
|
VIEW |
17.27 |
A |
.600 |
SECTION A-A |
|
.030 |
|
|
|
|
0.76 |
|
|
|
|
SWITCH |
|
MAGNET |
|
INSTALLATION INSTRUCTIONS
•Mark location for the switch on the door frame and mark the location for the magnet on the top edge of the door.
•Make sure switch and magnet hole locations are aligned.
•Using a square, transfer the marks on to the top edge of the door and the opposing door frame.
•Using a tape measure or graduations on the square, locate the center of the door edge and place an intersecting line with the first mark. Mount the donut magnet using the #4X1/2 flathead screw provided.
•Repeat the above step to locate the hole position for the switch in the door frame. Drill a 3/8” hole in the door frame.
•Connect the switch leads to the alarm system. Caution! Hold wire leads, not the switch housing while cutting and stripping to prevent damage to switch.
•Insert wire leads into hole followed by the switch and press the switch into the hole until the head is flush with the door frame
•Test switch for correct operation and make sure gap performance is acceptable.
DWG No. 131119-07 Rev. 1
Royne Industries LLC, dba NASCOM | P: 800.843.5530 | F: 800.727.4041 | www.nascominc.com |
2 |
Loading...