This guide provides information for frequently used features. For more information about these and other features,
refer to the user guide. For voice mail information, refer to the voice mail user guide for your system.
Feature Buttons
Most of the following feature codes work when your
endpoint is idle. However, if you are on an active call or
if the endpoint is off-hook, you may need to press
(Special) to activate the feature before you enter the
feature code.
If you make a mistake when entering numbers or
characters, you can press (Hold) to move the
cursor to the left and delete the characters entered, or
you can press
ButtonAction
(Up)
(Down)
(Speaker)
(Mute)Mutes the microphone during a
(Directory)Activates the contact and feature
(Special)
(Redial)Calls the last external number
(Hold)Places the current call on hold.
(Message)Connects to voice mailbox and
* to cancel the feature.
Provides volume control.
Scrolls through feature options.
Activates Handsfree Mode.
Activates features.
call.
DIrectory.
Activates features while on a call.
The (Special) button does not
cancel features. To cancel
features, press the Star button (*).
dialed. Y ou cannot redial internal
numbers.
Left/Backspace when entering
dialpad characters.
(Transfer)Transfers the current call.
Right/Forward when entering
dialpad characters.
notifies when you have
messages.
T oggles between Alpha Mode and
Numeric Mode when entering
dialpad characters.
Commonly Used Feature Codes
Contact your system administrator for more information
about system features.
FeatureCode
ACD Agent – Log In/Out328
Automatic IC Call Access – On/Off361
Automatic Trunk Call Access – On/Off360
Background Music – On/Off313
Call Forward – All Calls355
Call Logging333
Conference5
Default Station394
Directory307
Display Time And Date300
Do-Not-Disturb – On/Off372
Handsfree – On/Off319
Headset – On/Off317
Hold – Individual336
Hold – System335
Hunt Group – Remove/Replace 324
Message – Cancel Left Message366
Message – Delete Message368
Message – Leave Message367
Message – View Messages Menu365
Microphone Mute – On/Off314
Page Receive – On/Off325
Program Buttons397
Program Station Password392
Programmable Buttons – Default395
Queue (Callback) Request6
Record-A-Call385
Reverse Transfer (Call Pick-Up)4
Ring Tone Selection398
Station Speed Dial382
Station Speed Dial – Programming383
Switch Keymap399
System Forward – On/Off354
System Speed Dial381
View Button Assignments396
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008
Page 4
Answering Calls
Lift the handset, or press (Speaker) to
answer a call while using a headset or to answer
a call in Handsfree Mode.
Placing Emergency Calls
Dial the emergency number (911 U.S. or
999/112 Europe) . The system immediately places
the emergency call as soon as you dial the
number, even if you do not select an outside line.
Placing Internal (Intercom) Calls
With or without the handset lifted, dial the
extension number. If you enter incorrect digits,
you can press (Hold) to move the cursor
backward, deleting the last digits entered. If you
are using Handsfree Mode, listen for the double
tone, and then begin to speak.
Placing External Calls
Press the Outgoing button, an unlit Call button,
or enter the Outgoing Call access code (8 is the
default code), and then dial the number.
Redialing External Numbers
With or without the handset lifted, press the
(Redial). The system automatically select s
a line and dials the number.
Placing Conference Calls
1. While on the first call, press the Conf button to
place the call on hold. CALL NEXT PARTY TO
CNF appears.
2. Place a call to the next conference party. For
external calls, press the Outgoing button or
enter the Outgoing Call access code (8 is the
default code), and then dial the number.
3. After the party answers, announce the
conference, and then press the Conf button to
place the call on hold. If necessary, repeat this
step to add the remaining conference party.
4. Press the Conf button again to start the
conference. CNF IN PROGRESS appears.
Viewing and Responding to Messages
1. With the handset on-hook, press (Message).
Messages are displayed as first in/first out. If
there is more than one message, you can
repeatedly press (Message) to scroll through
the messages.
2. When the desired message is displayed, press #,
or lift the handset for privacy, and then press # to
respond. (If your handset is off-hook and you
press (Message), you automatically place a
call to the party or message center who left the
message.)
T ransferring Calls to Other Extensions
1. While on the call, press (Transfer), and
then enter the extension number.
2. Do one of the following:
• Wait for an answer, announce the call, and
then hang up. If the extension is
unavailable, press the flashing IC or Call
button to return to the caller.
• Hang up to transfer the call and disconnect
the call from your endpoint.
Forwarding Calls
1. Press the Fwd button, and then enter the feature
code, if applicable. ENTER FORWARD DEST
appears.
2. Enter the extension number, or press the
Outgoing button or enter the Outgoing Call
access code (8 is the default code), and then dial
the telephone number.
Using Do-Not-Disturb
1. Press the DND button, and then do one of the
following:
• Press (Up) or (Down) to scroll
through the messages.
• Enter the two-digit number for the DND
message.
2. After selecting the message, enter the additional
text for the DND description, if applicable.
3. Press (Speaker), or lift and replace the
handset.
Placing a Page Announcement
1. Press 7.
2. Enter the page-zone number (0 to 9).
3. After the tone, make your announcement, and
then hang up.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008
Page 5
Notice
Enter provider information above.
This guide is released by Mitel Networks Corporation and provides information necessary to use the
Model 5212/5224 endpoints. The guide contents, which reflect current Mitel standards, are subject to revision or
change without notice.
Some features or applications mentioned may require a future release and are not available in the initial release.
Future product features and applications are subject to availability and cost. Some features or applications may
require additional hardware, software, or system administrator assistance.
For sales, service, or technical support, contact your local authorized provider:
If you do not know the contact information for your local provider, use the “Strategic Partners & Resellers – Mitel
Partner Locator” link at the top of the Mitel home page
(www.mitel.com) to find a location near you.
If you have any questions or comments regarding this user guide or other technical documentation, contact the
Technical Publications Department (USA) at:
tech_pubs@mitel.com
®
is a registered trademark of Mitel Networks Corporation.
Mitel
®
Inter-Tel
All other trademarks mentioned in this document are the property of their respective owners, including Mitel Networks
promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse
any copyrighted component of this work in other works must be obtained from Mitel.
is a registered trademark of Inter-Tel (Delaware), Incorporated.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page i
Page 6
Important Safety Instructions and Precautions
Remember the following safety guidelines when using the endpoint.
Programming Emergency Numbers
Make sure to do the following when programming emergency numbers and/or making test calls to emergency
numbers:
• Remain on the line and briefly explain to the dispatcher the reason for the call.
• Perform tests during off-peak hours such as early morning or late evenings.
Safety Notices
The following notices may appear on the product or in the technical documentation.
NoticeDescription
Caution indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury and/or damage to the equipment or property.
Warning indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
Danger indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury.
The exclamation point within an equilateral triangle indicates that important operating and
maintenance (servicing) instructions are included in the literature accompanying the
product.
Maintenance and Repair
There are no user serviceable parts inside the endpoints. For repairs, return the endpoint to an authorized Mitel
provider.
NOTE
Changes or modifications not expressly approved by Mitel may void the user’s right to operate the
equipment.
Page iiMitel® Model 5212/5224 User Guide – Issue 2, October 2008
Page 7
Power Requirements
CAUTION
Endpoint Damage Hazard. To avoid damaging the endpoint, make sure the endpoint is connected to the proper
power supply before powering on. Contact your system administrator for more information.
The endpoint requires any one of the following power supplies:
• Mitel 48-volt DC Ethernet power adaptor 100-240 volt AC 50-60Hz (ES) -part number 50005301
• An industry-standard IEEE 802.3af Power over Ethernet (PoE) power supply unit
If your endpoint uses a centralized PoE power supply unit, do not use the 48-volt DC Ethernet power adaptor. If
necessary, contact your system administrator for assistance before connecting your endpoint to the centralized power
source.
Make sure the endpoint is plugged into an uninterruptible power supply (UPS). If your endpoint is plugged into the
UPS and the power fails, it should remain powered on for about 10 minutes. If the endpoint is not plugged into a UPS
and the power fails, the current call is dropped and you will not be able to use the endpoint until the power is restored.
Software Updates
CAUTION
Endpoint Damage Hazard. Do not use your endpoint or disconnect it from the power supply while it is updating
software.
The endpoint may require occasional software updates when new versions are available. The endpoint is configured
to download the updates automatically. Contact your system administrator for more information.
Product Disposal Instructions
This symbol indicates that the product is classified as electrical or electronic equipment and should not be disposed of with
other commercial or household waste at the end of its working life. For appropriate disposal and recycling instructions,
contact your local Mitel provider.
The Waste of Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) was established by the European Union to
minimize negative impact on the environment, control hazardous substances, and curtail landfill expansion by using the best
available recovery and recycling techniques.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page iii
Page 8
Endpoint Usage
This equipment is not for connection to the telephone network or public coin phone service. It is only for use when
connected to Mitel systems.
WARNING
When using your endpoint equipment, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and injury to persons, including the following:
• Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool.
• Avoid using an endpoint (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning.
• Do not use the endpoint to report a gas leak in the vicinity of a leak.
• Do not connect directly to the Public Switched Telephone Network (PSTN). Any connection of this
endpoint to an off premise application, an out of plant application, any other exposed plant application,
or to any equipment other than the intended application may result in a safety hazard, and/or defective
operation, and/or equipment damage. “Exposed plant” means where any portion of the circuit is subject
to accidental contact with electric lighting or power conductors operating at a voltage exceeding 300
volts between conductors or is subject to lightning strikes.
• The socket outlet, if used, shall be located near the equipment and shall be easily located by the user.
• Use only Mitel approved power adaptors.See “Power Requirements” on page iii.
• The handset supplied with the endpoint is not certified for use with any other phone. Use of the handset
with any other phone may have the potential to cause hearing loss in the event of a lighting strike on
the outside plant wiring.
Page ivMitel® Model 5212/5224 User Guide – Issue 2, October 2008
Page 9
Notice to Canadian Customers
The Class B digital apparatus complies with Canadian ICES-003.
Notice to U.S. Customers
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. Ho w ev er,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Notice to European Customers
We, Mitel Networks LTD.
Of, Mitel Castlegate Business Park
Portskewett
Caldicot
NP26 5YR
UK
Declare that for the hereinafter mentioned product the presumption of
conformity with the applicable essential requirements of
DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT (RTTE DIRECTIVE) AND OF THE COUNCIL is given.
Mitel Endpoints: 5212/5224
Any unauthorized modification of the product voids this Declaration.
For a copy of the original signed Declaration of Conformity (in full conformance with EN45014), please contact the Regulatory
Approvals Manager at the above address.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page v
Model 5212/5224 User Guide – Issue 2, October 2008
Page 15
Getting Started
Welcome
The instructions in this guide are for using the Mitel 5212/5224 Internet Protocol (IP) endpoint
on the Mitel 5000 system. The Quick Reference Guide located at the beginning of this guide is
an overview of frequently used features.
Your endpoint should be powered on and ready to use. If the display is blank, or if the display
name, extension number, or time or date are incorrect, contact your system administrator for
assistance.
Because a variety of voice mail products work with the Mitel 5000 system, this guide does not
include voice mail instructions. For voice mail instructions, refer to the voice mail user guide for
your system. For example, refer to the Enterprise Messaging, Basic Voice Mail, and Embedded
Voice Mail Card User Guide, part number 835.3205, or the NuPoint Messenger
Guide on the Mitel Web site (http://edocs.mitel.com). Contact your system administrator for
more information about your voice mail system.
Because many endpoint features can be programmed to perform various tasks,
NOTE
some features may work differently than the descriptions in this guide. Contact
your system administrator for more information.
Getting Started
Messaging User
About Your Endpoint
The Mitel Models 5212 and 5224 are full-feature, dual port endpoints that provide voice
communication over an IP network. Both models have a back-lit liquid crystal display (LCD),
display-assisted feature access, on-hook dialing, and a Ring/Message Indicator.
For one-touch feature access, the Model 5212 has 12 programmable buttons and the Model
5224 has 24 programmable buttons. Both endpoints have 10 fixed feature buttons to access
commonly used features such as Transfer, Redial, Mute, and so on.
Mitel® Model 5212/5224 Endpoint User Guide– Issue 2, October 2008Page 1
Page 16
Getting Started
1
2
3
4
5
7
6
Model 5212 Features
The Model 5212 is shown here. See “Endpoint Feature Descriptions” on page 4 for more
information about the endpoint features.
Mitel® Model 5212/5224 Endpoint User Guide– Issue 2, October 2008Page 3
Page 18
Getting Started
Endpoint Feature Descriptions
The following sections describe default configurations. Your endpoint may be programmed
differently. Contact your system administrator for more information. See “Model 5212 Features”
on page 2 and “Model 5224 Features” on page 3 for endpoint feature locations.
Handset
The handset provided with this equipment is hearing aid compatible (HAC). If you are using a
headset or if you are in Handsfree Mode, you do not need to use the handset. See “Headset
Instructions” on page 7 and “Using Handsfree Mode” on page 29 for more information.
Display
The display provides a two-line, 20-character viewing area for using features and identifying
callers. When idle, the display shows user information and the time and date.
Display Buttons
The Model 5224 (only) has three Display buttons under the Display. In some features, the left
and right Display buttons provide back (<<) and forward (>>) navigation. The center Display
button always displays user and system information. See “Viewing Your System Information” on
page 31 for more information.
Ring/Message Indicator
The Ring/Message Indicator flashes or stays lit to indicate call, message, and feature activity.
For more information about messaging features, see “Messages” on page 39. Ring/Message
Indicator signals are described in the following table.
Indicator SignalsDescription
Rapidly flashingYou have an incoming call.
Slowly flashingYou have a waiting message or callback message.
OnYou are on a call or using a feature.
OffYour endpoint is idle.
Speaker
The speaker provides audio for handsfree calls and background music. See “Using Handsfree
Mode” on page 29 for information about handsfree calls. See “Listening to Background Music”
on page 12 for more information about background music.
NOTE
The Model 5212 uses half-duplex audio when using the speakerphone (both
parties cannot talk at the same time).
Page 4Mitel
®
Model 5212/5224 Endpoint User Guide– Issue 2, October 2008
Page 19
Getting Started
Feature Buttons
Feature buttons provide quick access to commonly used features. See the following table for
descriptions.
ButtonAction
(Up) (Down)Provides volume control for the ringer, handset, and
speaker.
Scrolls through feature options.
(Speaker)Activates Handsfree Mode (speakerphone). See
“Using Handsfree Mode” on page 29.
Activates features.
(Mute)Temporarily turns off your microphone during a call.
(Directory)Activates the contact and feature Directory. See
“Using the Directory” on page 26.
(Special)Activates features while on a call. The (Special)
button does not cancel features. To cancel features,
press the Star button (
RedialCalls the last external number dialed. You cannot
redial internal numbers.
*).
(Hold)Places the current call on hold.
Left/backspace when entering dialpad characters.
See “Using the Dialpad Buttons to Enter Characters”
on page 23.
(Transfer)Transfers the current call.
Right/forward when entering dialpad characters. See
“Using the Dialpad Buttons to Enter Characters” on
page 23.
(Message)Connects to your voice mailbox and flashes to notify
you of waiting messages.
Toggles between Alpha Mode and Numeric Mode
when entering dialpad characters.
Dialpad Buttons
Use the dialpad buttons to dial phone numbers, enter feature codes, and to enter characters
when using features that require text input.
Programmable Buttons
The Model 5212 has 12 programmable buttons.The Model 5224 has 24 programmable buttons.
The top seven buttons on both models are programmed by the system administrator and cannot
be reprogrammed. However, you can program the remaining buttons for quick access to
features or speed-dial entries. See “Assigning Features to Programmable Buttons” on page 12
for instructions.
Mitel® Model 5212/5224 Endpoint User Guide– Issue 2, October 2008Page 5
Page 20
Getting Started
Endpoint Signals
The Model 5212/5224 has several audio and visual signals to indicate feature activity. The
following are a few helpful tips:
• Lit or blinking buttons indicate call or feature activity.
• All endpoint button lamps illuminate at the same time for a few seconds when the endpoint
is reset or powered on.
• The following actions may cause an error tone:
o Pressing an invalid button combination.
o Selecting a restricted feature.
o Dialing a restricted or invalid number.
o Dialing too slowly between digits.
o Waiting too long before performing the next step.
To correct an error tone, hang up and try again.
• Many features “time-out” if you wait too long before performing the next step. If this
happens, you must start over.
• “Off-hook” means the handset is lifted. “On-hook” means the handset is in the cradle.
• If your endpoint does not have a lamp under the speaker button, the large message
indicator lamp on the top right of the endpoint indicates that the speakerphone is in use.
Comfort and Safety Tips
Observe the following comfort and safety tips when using the endpoint:
• Do not cradle the handset: Prolonged use of the handset can lead to neck, shoulder, or
back discomfort, especially if you cradle the handset between your neck and shoulder. If
you frequently use the endpoint, you might find a headset more comfortable. See
“Headset Instructions” on page 7.
• Adjust the viewing angle: The built-in stand tilts to give you a better view of the buttons.
See “Adjusting the Viewing Angle” on page 9.
• Protect your hearing: Because prolonged exposure to loud sounds can contribute to
hearing loss, keep the volume at a moderate level. You can adjust the volume levels of the
handset receiver or headset. See “Changing Volume Levels” on page 11.
Page 6Mitel
®
Model 5212/5224 Endpoint User Guide– Issue 2, October 2008
Page 21
Headset Instructions
When using a headset, press (Speaker) to connect to or disconnect from calls. The
Headset icon appears when the headset is in use. You cannot use the handset or
speakerphone when the endpoint is in Headset Mode . Disconnecting the headset automatically
enables the handset.
The headset must be hearing aid compatible (HAC).
NOTES
T o connect and activate the headset:
1. Insert the headset jack into the Headset port located on the back of the endpoint.
2. Dial 317
T o turn off Headset Mode and activate the handset and speakerphone:
If your headset has a power-saver mode, make sure the system administrator has
enabled the “Headset Connect Tone” feature. If this is not enabled, you may miss
the first few seconds of an incoming call.
(Headset on/off). HEADSET MODE ON appears.
NOTE
Dial 317
(Headset on/off). HEADSET MODE OFF appears.
Getting Started
Because Headset Mode disables the handset and speakerphone, you
must turn off Headset Mode before you can use the handset or
speakerphone.
Mitel® Model 5212/5224 Endpoint User Guide– Issue 2, October 2008Page 7
Page 22
Page 23
Personalizing Your Endpoint
Press tabs on both sides
to release and detach unit.
This chapter describes features you can use to personalize your endpoint.
Adjusting the Viewing Angle
You can tilt the endpoint stand for a better view of the buttons and display.
Personalizing Your Endpoint
T o adjust the viewing angle:
1. Turn the endpoint so it faces away from you.
2. Hold the base firmly, and then press the tabs on the sides of the stand to release and
detach the base unit.
3. Hinge the hooks on the base unit into the notches on the back of the endpoint, and then
snap into place as follows:
• For a high-angle mount, hinge the two lower hooks into the bottom set of notches,
and then snap the two upper hooks into the middle set of notches.
• For a low-angle mount, hinge the two lower hooks into the middle set of notches,
and then snap the two upper hooks into the top set of notches.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 9
Page 24
Personalizing Your Endpoint
Lens
Fixed Mylar
designation card
module
Option
Installing Designation Cards
If you program buttons on your Model 5212/5224 (see page 12), you can install a new paper
designation card with the revised button labels. (Paper designation cards are provided by your
system administrator.) You can usually slide the paper designation card out and replace it
without removing the lens (if necessary, see the following instructions to remove the lens for
either model).
If you have a Model 5224, you can remove the lens and install a fixed Mylar
which has labels for the three menu buttons under the display. Contact your system
administrator for the Mylar designation card.
To remove the lens and install the fixed Mylar designation card (Model 5224):
1. Remove the screw that holds the option module on th e back of the phone. Keep the
screw in a safe place—you must use it in step 6..
2. Lift the lower edge of the option module until you feel the inner tabs release, and then
gently lift the upper edge of the module. (To avoid damaging the module or the lens,
always lift the lower edge of the module first.)
3. Remove the lens by lifting the upper edge, and then sliding the lower edge down.
4. Place the fixed Mylar designation card on the face of the endpoint.
5. Slide the lens tabs into the underside of the endpoint.
6. Snap the lens tightly into place by applying pressure to both the middle and top of the
lens. Secure the option module using the screw from step 1..
®
designation card,
Page 10Mitel
®
Model 5212/5224 User Guide– Issue 2, October 2008
Page 25
Changing Volume Levels
You can change the following volume levels:
• Ringer (alerting tone)
• Handset
• Headset
• Background music
• External speaker
Turning the external speaker volume down to the lowest levels may prevent you
NOTE
You must be using the feature to change the volume level. For example, if you want to change
handset volume level, you must be using the handset. However, you can adjust the ringer
(alerting tone) volume level when the endpoint is idle.
To change a volume level:
from hearing the feature “warning tones” that notify you when errors occur (for
example, when you enter an incorrect feature code).
While using the feature, press (Up) to incre ase the volume or press (Down) to
decrease the volume. The volume level is automatically saved.
Personalizing Your Endpoint
Changing the Ring Tone
You can select one of nine different ring tones.
To change the ring tone:
1. With the handset on-hook, dial 398.
2. Do one of the following to listen to (or turn off) ring tones:
• Press 0 to turn the ringer off.
3. Press (Up) or (Down) or 1 to 9 to listen to ring tones.Press (Speaker), #, or
lift and replace the handset to select the ring tone.
Adjusting the Display Contrast
You can adjust the display Contrast setting.
To adjust the Contrast setting:
1. While the handset is on-hook, dial 303.
2. Do one of the following to adjust the contrast:
• Press (Up) or (Down) to adjust the contrast.
• Press a number on the dialpad (1 = lightest, 10 = darkest) that corresponds to your
desired contrast level.
3. To save the setting, press # or (Speaker).
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 11
Page 26
Personalizing Your Endpoint
Changing the Language
Your system administrator can select two of the following languages as the primary and
secondary languages to display text.
1
• American English
• British English
• Spanish
For example, if your system administrator programmed your endpoint with American English as
the primary language, American English is used for display text. You can change the language
by selecting the secondary language. Contact your system administrator for more information.
To change the language:
Dial 301 to select either the primary or secondary language. The display shows text in the
selected language.
Listening to Background Music
If your system is equipped with a music source, you can listen to background music or system
audio (for example, organizational conference calls) through the external speaker.
To turn on or turn off background music:
313 (on/off). BACKGROUND MUSIC ON (or OFF) appears.
Dial
Assigning Features to Programmable Buttons
For quick access, you can assign feature codes, extensions, or speed-dial numbers to your
programmable buttons. You can then press the programmed buttons to activate features or
place calls. See “Default Access Codes” on page 13 and “Default Feature Codes” on page 13
for code lists.
Before assigning a speed-dial number to a programmable button, the number must
be stored with either a Station or System speed-dial code. See “Using Speed Dial”
NOTES
To assign a feature, extension number, or speed-dial code to a button:
1. With the handset on-hook, dial 397.
2. Press the button that you want to program. UNDEFINED KEY appears. If the button is
3. Enter the feature code, extension number, or speed-dial code (0 to 9) to be assigned to
4. Record the button assignments on the designation card. See “Installing Designation
on page 22.
You cannot reprogram the default button assignments. See “Programmable
Buttons” on page 5.
not programmable, NON-PROGRAMMABLE KEY appears.
the button.
Cards” on page 10.
1.This feature may or may not be enabled for your system.
Page 12Mitel
®
Model 5212/5224 User Guide– Issue 2, October 2008
Page 27
Default Access Codes
The following are default system access codes. If your system uses different codes, record the
codes in the “New Code” column for reference.
Outside Line Access Codes
Code Type CodeNew Code
Emergency Call 911 (999/112 Europe)
Outgoing Call (Default)8
Select Line Group 1 to 208 92001 to 92208
Automatic Route Selection92000
Extension Numbers
Code TypeCodeNew Code
Attendant0
Endpoint Extensions1000 to 1999
Hunt Groups2000 to 2299
Personalizing Your Endpoint
Default Feature Codes
The following table lists default feature codes. If your system administrator changes any of the
default codes, you can record the new codes in the “New Code” column for reference.
Most of the following feature codes work when your endpoint is idle. However, if
you are on an active call or if the endpoint is off-hook, you may need to press
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 13
Page 28
Personalizing Your Endpoint
Automatic Trunk Answer20350
Background Music – On/Off12313
Barge-in48386
Call Forward – All Calls32355
Call Forward – If Busy32357
Call Forward – If No Answer32356
Call Forward – No Answer/Busy32358
Call Logging35333
Change Language12301
Conference335
Default Station17394
Directory26307
Display Time And Date31300
Do-Not-Disturb41370
Do-Not-Disturb – Cancel41371
Do-Not-Disturb – On/Off41372
Do-Not-Disturb – Override41373
FeaturePageCodeNew Code
Group Listen34312
Handsfree – On/Off29319
Headset – Off7316
Headset – On7315
Headset – On/Off7317
Hold – Individual30336
Hold – System30335
Hookflash (Recall in Europe)30330
Hunt Group – Remove47322
Hunt Group – Remove/Replace 47324
Hunt Group – Replace47323
LCD Contrast Control11303
Message – Cancel Left Message40366
Message – Delete Message40368
Message – Leave Station Message39367
Message – View Messages40365
Microphone Mute – On/Off29
314
Page 437
Page Receive – On/Off43325
Program Buttons12397
Page 14Mitel
®
Model 5212/5224 User Guide– Issue 2, October 2008
Page 29
Personalizing Your Endpoint
FeaturePageCodeNew Code
Program Station Password36392
Programmable Buttons – Return to Default16395
Queue (Callback) Request216
Record-A-Call34385
Redial22380
Redirect Call20331
Reminder Message41305
Reminder Message – Cancel41306
Remote Programming36359
Reverse Transfer (Call Pick-Up)314
Ring Intercom Always – On/Off29377
Ring Tone Selection11398
Station Monitor48321
Station Speed Dial23382
Station Speed Dial – Programming23383
Steal Call48387
System Forward – Off32353
System Forward – On32352
System Forward – On/Off32354
System Speed Dial24381
Switch Keymap17399
Transfer To Hold30346
Transfer To Ring30345
View Programmable Button Assignments15396
Viewing Button Assignments
You can view programmable button (key) feature assignments.
To view button assignments:
1. With the handset on-hook, dial 396. PRESS THE KEY TO REVIEW appears.
2. Press any of the feature buttons to display the assignment.
3. Press # or (Speaker) to exit.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 15
Page 30
Personalizing Your Endpoint
Resetting Programmable Buttons
You can reset all buttons (keys) that you have programmed to the default assignments.
Resetting the programmable buttons does not reset button assignments programmed by the
system administrator.
T o reset the feature buttons to the default values:
With the handset on-hook, dial 395. FEATURE KEYS DEFAULTED appears.
Programming DSS/BLF Buttons
You can use programmable buttons as Direct Station Selection/Busy Lamp Field
(DSS/BLF) buttons. DSS/BLF buttons must be enabled by your system administrator.
After you program a DSS/BLF button, you can:
• Press the button to place a call to the assigned extension.
• Press the button and then hang up to transfer a call to the assigned extension. If the call is
transferred to voice mail you hear repeating double tones.
• Visually monitor the call activity of the assigned extension.
The following table describes the lamp signals and the indicated call activity:
Lamp SignalsDescription
Continuously LitThe extension is busy or off-hook.
Slowly flashingThe extension is in Do-Not-Disturb (DND).
Quickly flashingThe extension has a call ringing in.
Continuously flashingThe extension is causing a “Station Off-Hook” system alarm.
To assign a DSS/BLF button:
1. With the handset on-hook, dial 397.
2. Press the programmable button, and then enter the extension number to be assigned to
the button.
Page 16Mitel
®
Model 5212/5224 User Guide– Issue 2, October 2008
Page 31
Personalizing Your Endpoint
Resetting the Endpoint to the Default Settings
Resetting the endpoint to the default settings does the following:
• Returns all volume settings to the default levels. See “Changing Volume Levels” on
page 11.
• Cancels Background Music. See “Listening to Background Music” on page 12.
• Cancels Callback (queue) requests. See “Requesting a Callback (Queuing the Endpoint)”
on page 21.
• Restores Handsfree Mode. “Using Handsfree Mode” on page 29.
• Cancels Manual Call Forwarding. See “Manual Call Forwarding” on page 32.
• Cancels System Forwarding. See “System Forwarding” on page 32.
• Cancels Do-Not-Disturb (DND). See “Using Do-Not-Disturb (DND)” on page 41.
• Restores Page settings. See “Paging Other System Users” on page 43.
• Resets hunt group calls. See “Hunt Groups” on page 45.
To reset your endpoint to the default settings:
Dial 394. STATION DEFAULTED appear s.
Switching Keymaps
Keymaps are the default button assignments on your endpoint. Your system may have
programmed an alternate keymap, allowing you to switch between keymap assignments.
Contact your system administrator for more information.
T o switch between keymaps when your endpoint is idle:
With the handset on-hook, dial 399. The display shows either ALTERNATE (or)
ST ANDARD KEYMAP IS ACTIVE.
T o switch between keymaps during a call:
Press
(Special), and then dial399.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 17
Page 32
Page 33
Answering and Placing Calls
The following instructions describe how to answer and place internal and external calls and how
to use related features.
Answering and Placing Calls
NOTE
Answering Calls
Your endpoint may be preset to automatically answer incoming internal calls in Handsfree
Mode. To disable Handsfree Mode, see “Using Handsfree Mode” on page 29. After disabling
Handsfree Mode, you can use your handset or headset to answer incoming calls.
To answer a call:
Lift the handset, or press (Speaker) to answer a call while using a headset or to
answer a call in Handsfree Mode. See “Using Handsfree Mode” on page 29.
If you are currently on a call, press the flashing IC or Call button to answer a waiting call.
See “Answering Waiting Calls” below.
Answering Waiting Calls
If you receive a call while you are on another call, you hear a “call waiting” tone, the IC or Call
button flashes, and the display shows the Caller ID information (if available).
To answer a waiting call:
Press the flashing IC or Call button. This places the first call on hold and connects you to
the waiting call. You can also place the first call on hold before you answer the waiting
call. See “Placing Calls On Hold” on page 30.
By default, internal (intercom) calls are assigned to the IC button, and external
calls are assigned to the Call buttons.
Using Automatic Call Access
Automatic Call Access connects you to incoming internal or external calls when you pick up the
handset or press (Speaker). When Automatic Call Access is turned off, you must press the
flashing IC or Call button to answer incoming calls.
To use Automatic Call Access for incoming IC calls:
With the handset on-hook, dial 361 to turn on (or off). AUTO IC ACCESS ON (or OFF)
appears.
To use Automatic Call Access for incoming external (tr un k) calls:
With the handset on-hook, dial 360 to turn on or off. AUTO TRNK ACCESS ON (or OFF)
appears.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 19
Page 34
Answering and Placing Calls
Redirecting Calls
You can redirect incoming calls to another exten sion or external number.
T o redirect calls:
1. While a call is ringing, dial 331.
2. Enter the extension number, or press the Outgoing button or enter the Outgoing Call
access code (8), and then enter the external number. The call is forwarded to the
number entered.
Using Automatic Trunk Answer
You can use Automatic Trunk Answer to answer incoming external calls for other internal parties
who are members of an “Answer Access” list. Your system administrator creates Answer
Access lists. Contact your system administrator for Answer Access list extensions.
Automatic Trunk Answer answers calls in the order they are received (that is, the first call
received by any extension in the Answer Access list is the first one answered).
To use Automatic Trunk Answer:
1. While an incoming external call is ringing at another Answer Access list extension, lift the
handset or press (Speaker).
2. Dial 350 or press the flashing Trunk <number> button.
1
Placing Calls
The following instructions describe how to place calls and related features.
Placing Emergency Calls
WARNING
Contact your system administrator and your local Mitel provider for important information about
dialing emergency services before using your endpoint.
When dialing an emergency number (911 U.S. or 999/112 Europe), you do not have to press
the Outgoing button or enter the Outgoing Call access code (8 is the default code). The system
automatically places emergency calls immediately after you dial the number, even if you do not
select an outside line.
1.This feature may or may not be enabled for your system.
Page 20Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 35
Placing Internal Calls
Internal calls are calls placed to other extensions in the system. Internal calls are assigned to
the Intercom (IC) button on your endpoint. Contact your system administrator for a list of
extension numbers.
To place an internal call:
With or without the handset lifted, dial the extension number. If you enter incorrect digits,
you can press (Hold) to move the cursor backward, deleting the last digits entered.
If you are using Handsfree Mode, listen for the double tone and then speak.
If there is no answer or if the extension is busy, you can do the following:
• Request a callback (queue). See “Requesting a Callback (Queuing the Endpoint)” below.
• Camp-on to the busy extension. See “Using Camp-on” below .
• Leave a message. See “Leaving Messages at Other Extensions” on page 39.
Requesting a Callback (Queuing the Endpoint)
When you request a callback (queue the endpoint), the system calls you when the extension is
available and places a call to the endpoint.
T o request a callback:
If there is no answer or if the extension is busy, press (Special) followed by 6, and
then hang up. QUEUE REGISTERED FOR <name> appears. When the extension
becomes available, your extension rings.
T o cancel the callback request:
Press 6. QUEUE REQUEST CANCELED appears.
Answering and Placing Calls
Using Camp-on
Camp-on keeps you connected to the called extension until it becomes available. You cannot
use Camp-on if the called extension is in DND, or if the call is forwarded to voice mail. See
“Using Do-Not-Disturb (DND)” on page 41.
To use Camp-on:
Stay on the line and wait for the extension to become available. Do not hang up. If
Camp-on is enabled, you hear Music-on-Hold while you are waiting.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 21
Page 36
Answering and Placing Calls
Placing External Calls
The following sections describe features used when placing external calls.
To place an external call:
1. Press the Outgoing button, an unlit Call button, or enter the Outgoing Call access code
(8 is the default code).
2. Dial the number.
Depending on system configuration, you may also be able to use one of the following methods
to select an outgoing line:
• Enter the Select Line Group feature code. The default codes are 92001 to 92208.
• Enter the Automatic Route Selection (ARS) feature code. The default code is 92000.
Contact your system administrator for more information about using Select Line Group or ARS
access codes.
NOTES
If you cannot place an external call because all outgoing lines are busy,
you can request a callback, which prompts the system to contact you
when a line becomes available. See “Requesting a Callback (Queuing
the Endpoint)” on page 21.
If you are prompted for an account code (indicated by a single beep),
you must enter an account code before you can place your call. See
“Using Account Codes” on page 27.
Redialing a Number
You can quickly redial the last external number dialed. You cannot redial extension numbers.
To use Redial:
With or without the handset lifted, press REDIAL. The system automatically selects
a line and dials the number.
Using Speed Dial
You can use speed dial to quickly dial stored phone numbers. Speed-dial numbers are either
stored in the system (System Speed Dial), or in your endpoint (Station Speed Dial).
Using System Speed Dial
Your system administrator assigns Speed-Dial location numbers, which are available to anyone
in the system. Contact your system administrator for more information.
• Press (Up) or (Down) to scroll through the speed-dial locations.
• Enter the speed-dial location (000 to 999 or 0000 to 4999).
3. Press # to dial the number.
Page 22Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 37
Using Station Speed Dial
You can use Station Speed Dial to store phone numbers for your personal use. Other system
users do not have access to your Station Speed-Dial numbers.
Storing Station Speed-Dial Numbers
You can store up to 10 Station Speed-Dial numbers.
To store a Station Speed-D ia l number:
1. With the handset on-hook, dial 383. PROGRAM STN SPD (0-9) OR SCROLL appears.
2. Do one of the following:
• Press (Up) or (Down) to scroll through the speed-dial locations.
• Enter the speed-dial location (0 to 9).
Press # to select the location.
3. Enter the name of the speed-dial contact (up to 10 characters). For dialpad character
descriptions, see “Using the Dialpad Buttons to Enter Characters” on page 23.
4. Press # to save the name.
5. Enter the extension number or external number. If you are storing an external number,
enter the Outgoing Call access code (default code is 8) before you enter the number. Do
not use hyphens or colons in stored speed-dial numbers.
6. Press # to save the location. STN SPD BIN # <number> UPDATED appears.
Answering and Placing Calls
Using the Dialpad Buttons to Enter Characters
You can use the dialpad buttons to enter text or numbers for features such as
Do-Not-Disturb (see page 41) and Station Speed Dial (see page 23).
The following are guidelines when entering dialpad characters:
• Press (Message) to switch from Alpha Mode to Numeric Mode. The (Message)
button stays lit in Alpha Mode and is off in Numeric Mode.
• Press (Hold) to move the cursor to the left and delete characters.
• Press (Transfer) to move the cursor to the right.
• In Numeric Mode, press # for a hyphen (-).
• In Numeric Mode, press * for a colon (:).
• Press #, (Speaker), or lift and replace the handset to save entries.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 23
Page 38
Answering and Placing Calls
T o use the dialp ad to enter characters:
Press the dialpad buttons as shown in the following table.
Button
Characters Represented
(in Alpha Mode)
0@ : . , 0
1- & ( ) 1
2A B C ‘ 2
3D E F ! 3
4G H I * 4
5J K L # 5
6M N O ñ 6
7P Q R S 7
8T U V ? 8
9W X Y Z 9
For example, to enter May 31, you could use the following sequence:
1. In Alpha Mode ( [Message] button is lit), press 6 once to enter an “M.”
2. Press 2 once to enter an “A.”
3. Press 9 three times to enter a “Y.”
4. Press (Message) to switch to Numeric Mode.
5. Press (Transfer) to enter a space.
6. Press 3.
7. Press 1.
8. Press (Speaker), #, or lift the handset to save the entry.
Dialing Station Speed-Dial Numbers
To dial a Station Speed-Dial number:
Do one of the following:
• Dial 382, and then enter the Station Speed-Dial location number (0 to 9). The
system dials the number.
• Press (Up) or (Down) to scroll through the speed-dial locations, and then
press # to select the location and dial the number.
You can also use a Station Speed-Dial button assigned to the number
NOTE
Page 24Mitel
you are dialing. See “Assigning Speed-Dial Entries to Programmable
Buttons” on page 25.
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 39
Answering and Placing Calls
Deleting Speed-Dial Entries
To delete a Station Speed-Dial entry:
1. With the handset on-hook, dial 383. PROGRAM STN SPD (0-9) OR SCROLL appears.
2. Do one of the following:
• Press (Up) or (Down) to scroll through the speed-dial locations.
• Enter the speed-dial location (0 to 9).
3. Press # to select the location.
4. Press (Hold) repeatedly until the name is erased, and then press # to continue.
5. Press (Hold) repeatedly until the number is erased, and then press #. STN SPD
BIN # <number> UPDATED appears.
Assigning Speed-Dial Entries to Programmable Buttons
You can assign Station or System Speed-Dial numbers to your programmable buttons.
NOTE
To program a System/Station Speed-Dial button:
1. With the handset on-hook, dial 397. PRESS THE BUTTON TO PROGRAM appears.
2. Press the feature button that you want to program as a speed-dial button.
Before assigning the speed-dial number to a programmable button, make sure
the number has either a Station or System Speed-Dial code assigned to it.
• Press (Up) or (Down) to scroll through the speed-dial locations.
• Enter the speed-dial location (0 to 9 forStation Speed-Dial or 000 to 999 or 0000 to
4999 for System Speed Dial).
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 25
Page 40
Answering and Placing Calls
Using the Directory
You can use the Directory to find internal or external contacts or find and activate system
features. The directory uses Intelligent Directory Search (IDS), which is similar to the “text on 9
keys” (T9) predictive search feature used for mobile phones. The Directory has the following
three subdirectories:
• Intercom: Find and dial internal numbers.
• Outside: Find and dial external numbers listed in the company directory.
• Feature: Find and activate system features.
When searching the directory, dialpad buttons can represent several characters, as shown in
the following table. As you enter characters, the entries that best match the characters entered
appear. The system connects the character sequence to possible directory matches. For
example, to find the name “Jones,” dial 56637.
ButtonCharacters Represented
00
11
22 A B C a b c Ç â ä à å ç Ä Å á
33 D E F d e f é ê ë è É
44 G H I g h i ï î ì í
55 J K L j k l
66 M N O m n o ô ö ò Ö ó ñ Ñ
77 Q P R S q p r s
88 T U V t u v ü û ù Ü ú
99 W X Y Z w x y z ÿ
(Up)Scroll to next entry
(Down)Scroll to previous entry
*Cancel se arch
#Activate selection
(Hold)Move the cursor to the left, deleting existing characters
See page 26 for detailed instructions on using the directory.
T o search for a directory name or feature:
1. Press (Directory), and then press one of the following:
• 1 for the IC directory.
• 2 for the Outside directory.
• 3 for the Feature directory.
2. Press the dialpad buttons to enter (up to 20) characters. See the table on page 26 for
dialpad button character de scri p ti ons.
3. Press
(Up) or (Down) to scroll through the entries.
The IC directory may display two similar entries, one without an asterisk
NOTE
4. Press # while the display shows the entry to dial a number or activate a feature code.
Page 26Mitel
and one with an asterisk. The entry without an asterisk is the primary
extension—the entry with an asterisk is a secondary extension.
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 41
Using Account Codes
Account codes record information for telephone record reports. You may be required to enter
account codes when placing calls. Contact your system administrator for more information
about using account codes.
There are three types of account codes:
• Standard account codes: Automatically entered into the telephone record report
whenever you place a call.
• Forced account codes: Entered before you can place an outside call.
• Optional account codes: Entered at any time during a call.
To enter an optional account code:
1. While off-hook, press (Special), and then dial 390.
2. Enter the optional account code, and then press #.
To set an account code for all calls placed from your endpoint:
Dial 391 followed by the account code, and then press #. This code is used for all calls
made from your endpoint until it is disabled.
T o disable the code:
Dial 391, and then press #. ACCOUNT CODE CLEARED appears.
Answering and Placing Calls
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 27
Page 42
Page 43
Call Features
The following sections describe call-related features.
Using Handsfree Mode
You can use Handsfree Mode to activate the speakerphone.
The Ring Intercom Always feature prevents calls from being answered in
Handsfree Mode (see the following section).
NOTES
To use Handsfree Mode:
Using Ring Intercom Always
You cannot use Handsfree Mode if you are using a headset, or if you have more
than one endpoint assigned to an extension number.
The Model 5212 uses half-duplex audio when using the speakerphone (both
parties cannot talk at the same time).
With the handset on-hook, dial 319. HANDSFREE MODE ON appears. Dial 319 to turn
handset mode off.
Call Features
Using Mute
If another extension has Handsfree Mode enabled for incoming internal calls (see the previous
section), you can use Ring Intercom Always to override Handsfree Mode on the extension,
requiring the called party to pick up the handset to answer your call.
T o override Handsfree Mode for the current call:
1. Before you enter the extension number, press #. RING EXTENSION NUMBER appears.
2. Dial the extension number.
To use Ring Intercom Always to always send non-handsfree calls:
With the handset on-hook, dial 377. RING IC ALWAYS ON appears. Dial 377 again to
turn Ring Intercom Always off.
You can use Mute to temporarily turn off your microphone, preventing the other party on the call
from hearing you.
To mute or unmute the microphone:
While on a call, press Mute on. MICROPHONE MUTE ON appears. When the
microphone is muted, the Mute button lamp is lit. Press Mute again to unmute the
microphone.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 29
Page 44
Call Features
Placing Calls On Hold
You can place calls on either Individual Hold or System Hold.
• Individual Hold: Places an internal or external call on hold at your endpoint.
• System Hold: Places an external call on hold in the system. You can then pick up the call
from any endpoint that indicates a flashing Call button for the call, including the endpoint
that placed it on hold.
To place a call on Individual Hold:
1. Press (Hold). ENTER EXTENSION NUMBER appears.
2. Hang up or place another call.
To place an outside call on System Hold:
1. Press (Special), and then dial
2. Hang up or place another call.
To return to a call that is on hold:
Press (Hold), and then lift the handset or press (Speaker). <Caller> WAS
HOLDING appears.
Entering a Hookflash
335. ENTER EXTENSION NUMBER appears.
Some telephone companies require you to enter a hookflash (a quick hang up and release) for
feature access.
To enter a hookflash:
While off-hook, press (Special), and then dial 330.
Transferring Calls
You can transfer calls to other extensions or external numbers. You can also transfer
conference calls. See “Transferring a Conference” on page 33 for more information.
Transferring Calls to Other Extensions
T o transfer a call to another extension:
1. While on the call, press (Transfer), and then enter the extension number.
2. Do one of the following:
• Wait for an answer, announce the call, and then hang up. If the extension is
unavailable, press the flashing IC or Call button to return to the caller.
• Hang up to transfer the call and disconnect the call from your endpoint.
If your system administrator has enabled Transfer-on-Connect for your
endpoint, you are automatica l l y con ne cted to calls transferred to your
NOTE
extension after the transferring party hangs up. If this option is turned
off, you must press a Call button to answer calls transferred to your
extension.
Page 30Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 45
Transferring Calls to External Numbers
To transfer a call to an external number:
1. While on the call, press (Transfer).
2. Press the Outgoing button or the Outgoing Call access code (the default code is 8) to
select an outside line.
3. Dial the phone number.
4. Do one of the following:
• Wait for an answer, announce the call, and then hang up. If the extension is
unavailable, press the flashing Call button to return to the caller.
• Hang up to transfer the call and disconnect the call from your endpoint.
Using Reverse Transfer
You can use Reverse Transfer (Call Pick Up) to answer calls that are ringing or holding at other
extensions. For example, if you receive a call while you are away from your desk, you can pick
up the call from another extension.
To use Reverse Tran s f er :
1. Lift the handset, and then press 4. ENTER EXTENSION NUMBER appears.
2. Dial the extension or hunt group number where the call is ringing or holding. The call is
transferred to the endpoint you are using and you are connected to the caller. See “Hunt
Groups” on page 45 for more information about using hunt groups.
Call Features
Viewing Your System Information
If you are on a call, you can temporarily view your user information (your user name and your
extension number) and the date and time.
To display your user information and the date and time:
Press (Special), and then dial 300.
Viewing Caller ID Information
If you are currently connected to an external caller with Caller ID, you can toggle between the
caller’s name and number. If the name is unavailable, CANNOT ACCESS FEATURE appears.
To show the outside party’s name/number:
Press (Special), and then dial 379.
Forwarding Calls
You can use Manual Call Forwarding (see page 32) or System Forwarding (see page 32) to
forward calls.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 31
Page 46
Call Features
Manual Call Forwarding
The following table describes Manual Call Forwarding options.
Call Forward FeatureDescriptionCode
Call Forward All CallsAll incoming calls are forwarded.355
Call Forward All CallsAll incoming calls are forwarded.355
Call Forward if no
Answer
Call Forward If BusyWhen your endpoint is busy, all
Call Forward If No
Answer/Busy
To use Manual Call Forwarding:
1. Press the Fwd button, or dial the Manual Call Forwarding feature code from the table
above. ENTER FORWARD DEST appears.
2. Enter the extension number, or press the Outgoing button and then dial the telephone
number. FWD ALL CALLS TO <number> appears.
To cancel a Manual Call Forwarding request:
Do one of the following:
• Press the Fwd button, and then press (Speaker), or lift and replace the handset. ANY
CALL FORWARD CANCELED appears.
System Forwarding
You can use System Forwarding to route calls based on the type of call and the idle or busy
status of your endpoint. You cannot program the System Forward destination. You can only turn
it on or off. Contact your system administrator for more information.
To turn on or turn off System Forwarding:
Dial 354 to turn System Forwarding on. SYSTEM FORWARD ON appears. Dial 354
again to turn System Forwarding off.
All incoming calls are forwarded if
not answered. (The timer is set by
the system administrator.)
incoming calls are forwarded without
ringing.
All incoming calls are forwarded if
your endpoint is busy, or if you do
not answer.
356
357
358
Page 32Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 47
Placing Conference Calls
You can place a conference call with up to three internal or external parties (for a total of four
parties, including yourself).
To place a conference call:
1. While on the first call, press the Conf button to place the call on hold. CALL NEXT
PARTY TO CNF appears.
2. Place a call to the next conference party (for external calls, press the Outgoing button
or the Outgoing Call access code [8 is the default code], and then dial the number).
3. After the party answers, announce the conference, and then press the Conf button to
place the call on hold. If necessary, repeat this step to add the remaining conference
party.
4. Press the Conf button again to start the conference. CNF IN PROGRESS appears.
Adding a Conference Party
You can add a conference party during the conference.
T o add a conference party:
1. Press the Conf button. This leaves the conference parties connected.
2. Place a call to the party to be added to the conference, and then announce the
conference. Press the Conf button (twice) to add the party and rejoin the conference.
Call Features
Transferring a Conference
You can transfer an existing conference to another extension.
To transfer a conference:
1. During the conference, press (Transfer), and then dial the extension number.
2. Announce the conference (if desired), and then hang up. CONFERENCE TFR from
<name> appears on the called party’s display. The party must then press the flashing
Conf button to connect to the conference.
Dropping Out of a Conference
You can drop out of a conference and return to the conference later.
To drop out of a conference:
Press the Conf button or (Hold), and then hang up. ENTER EXTENSION
NUMBER appears. This removes you from the conference but leaves the other parties
connected.
To return to the conference:
Press the flashing Call button. CONFERENCE WAS HOLDING appears, and you are
reconnected to the conference.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 33
Page 48
Call Features
Ending a Conference and Placing all Parties on Hold
You can end a conference and place all conference parties on Individual Hold, allowing you to
toggle between the held parties and speak to one party at a time.
T o end a conference and place all parties on Individual Hold:
Press the Conf button, and then press (Hold). CONFERENCE PARTIES ON
HOLD appears.
T o toggle between the held callers:
Press (Hold) twice for internal parties or the applicableCall button for external
parties.
Using Record-A-Call
.
NOTE
You can use Record-A-Call to record an ongoing call as a mailbox message.1 You can then
retrieve the message from your voice mailbox. The Record-A-Call feature stays active after the
other party hangs up, so you can add to the recorded call with your own message.
T o use Record-A-Call:
1. While on a call, press (Special), and then dial 385. REQUESTING
2. Enter the voice mailbox number where you want the recording to be saved.
This feature is not supported for peer-to-peer (P2P) calls. Contact your system
administrator for more information.
RECORD-A-CALL appears.
RECORD-A-CALL IN PROGRESS appears, and both you and the calling party hear a
confirmation tone (if enabled).
NOTE
T o stop Record-A-Call:
Do one of the following:
• Press (Special), and then dial 385.
• Hang up.
Using Group Listen
You can use Group Listen to activate the speaker while you use the handset or headset to
continue speaking. This allows other people to hear the other party on the call while the other
party can only hear you (through the handset microphone). You cannot use Group Listen in
Handsfree Mode.
To use Group Listen:
While on a call, press (Special), and then dial
LISTEN ON appears, and you hear a confirmation tone. The other party does not hear
the confirmation tone. Dial 312 again to turn Group Listen off.
Your system administrator can assign the Record-a-Call voice mailbox
destination. If so, you do not need to enter the voice mailbox number.
312 to turn Group Listen on. GROUP
1.This feature may or may not be enabled for your system.
Page 34Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 49
Using Call Logging
Call Features
Your call logs are records of your most recent missed, received, and dialed calls. A maximum of
20 entries are stored in each call log.
You can use Call Logging to:
2
• View recent call activity.
• View caller ID information.
• Return or redial calls.
To use Call Logging:
1. Dial 333.
2. Select one of the following options:
• Press 1 (MISS).
• Press 2 (RCV).
• Press 3 (DL).
• Press 4 (CLR).
3. Press (Up) or (Down) to scroll through the entries.
The display shows the party’s name and the extension or outside number (if available)
and the date and time.
If no Caller ID information is available, UNKNOWN CALLER appears.
To return a call or redial a number listed in a call log:
Press # while the display shows the number.
To delete individual call log entries:
Press 0 to delete the displayed entry.
2.This feature may or may not be enabled for your system.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 35
Page 50
Call Features
Using Secondary Extension Buttons
.Secondary Extension buttons must be programmed by your system administrator. You can use
programmable buttons as “secondary extensions.” Secondary Extensions are assigned to other
extensions in the system (primary extensions) Because Secondary Extension buttons are
programmed by the system administrator, you cannot change the buttons (for example, assign
features to the buttons).
When programmed, you can use Secondary Extension buttons to:
• Place an internal call to the primary extension.
• View the call activity at the primary extension.
• Transfer calls to the primary extension.
• Answer a call that is ringing or holding on any Call button at the primary extension.
The system administrator must set up the Call buttons for internal calls or you
cannot use Secondary Extensions at the primary extension.
You can use Secondary Extension buttons to notify you when a given number
NOTES
of calls are waiting at the primary extension.
If a Secondary Extension button is flashing (the primary extension has an
incoming call), you can press # before you press the flashing Secondary
Extension button to call the primary extension and not answer the incoming
call.
Remote Programming
You can use Remote Programming to access the DND and Call Forwarding features from
another system endpoint or an external phone.
A Direct Inward System Access (DISA) number is required to use Remote
NOTE
Entering a Remote Programming Password
Before using Remote Programming, you should enter a new password.
T o enter a Remote Programming password:
1. Dial 392. ENTER PASSWORD appears.
2. Enter your current password (the default password is your extension number), followed
3. Enter the new password followed by
4. Enter the new password again foll owed by #. DATABASE UPDATED appears.
To change the station password from another phone, see “Using Remote Programming to
Change the Password” on page 37.
Programming from an external phone. Contact your system administrator for more
information.
by #. CHANGE PASSWORD TO appears.
3
#. VERIFY PASSWORD appears.
3.This feature may or may not be enabled for your system.
Page 36Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 51
Using Remote Programming to Change the Password
You can use Remote Programming to change the station (endpoint) password.
To use Remote Programming to change the station password:
1. Do one of the following:
• Call your DISA number (provided by your system administrator). If necessary, enter
your (DISA) password.
• Use any endpoint on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your password followed by #.
5. Dial 392.
6. Enter the new password followed by
7. Enter the new password again foll owed by #.
#.
Using Remote Programming to Change DND Settings
See “Using Do-Not-Disturb (DND)” on page 41 for more information about using DND.
T o use Remote Programming to turn on DND:
1. Do one of the following:
• Call your DISA number (provided by your system administrator). If necessary, enter
your (DISA) password.
• Use any endpoint on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your password followed by #.
5. Dial 370.
6. Enter the DND message number (01 to 20), and then enter the second-line message
text (if applicable).
T o use Remote Programming to turn off DND:
Follow steps 1. through 4. above, and then dial 371.
Call Features
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 37
Page 52
Call Features
Using Remote Programming to Forward Calls
See “Manual Call Forwarding” on page 32 for more information about Manual Call Forwarding.
T o use Remote Programming to turn on Manual Call Forwarding:
1. Do one of the following:
• Call your DISA number (provided by your system administrator). If necessary, enter
your (DISA) password.
• Use any endpoint on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your password followed by #.
5. Dial one of the following Call Forwarding feature codes:
• 355 (All)
• 356 (No answer)
• 357 (Busy)
• 358 (No Answer/Busy)
6. Enter either an extension number or (8) followed by a telephone number.
T o turn off Call Forwarding:
Dial 355, and then hang up.
Page 38Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 53
Messages
This section describes the following system messaging features:
Messages
• Inter-station messages: Inter-station messages are alerts sent to your endpoint by other
internal parties, notifying you to contact the party who left the message. The
(Message) button and Message/Ring Indicator flash to notify you of the new
message. You can then either delete the message or reply to the message, which
automatically places a call to the party who left the message.
• Do-Not-Disturb (DND) messages: Messages that other internal parties see when your
endpoint is in DND. See “Using Do-Not-Disturb (DND)” on page 41.
• Reminder Messages: Messages that you can use to notify yourself of upcoming
appointments, meetings, and so on. See “Using Reminder Messages” on page 42.
• Pages: Announcements sent over endpoint speakers or external speakers. See “Paging
Other System Users” on page 43.
• Voice messages: System voice mail messages.
Because a variety of voice mail products work with the Mitel 5000 system,
this guide does not include voice mail instructions. For voice mail
instructions, refer to the voice mail user guide for your system. For example,
NOTE
refer to the Enterprise Messaging, Basic Voice Mail, and Embedded Voice
Mail Card User Guide, part number 835.3205, or the NuPoint Messenger
Messaging User Guide on the Mitel Web site (http://edocs.mitel.com).
Contact your system administrator for more information about your voice
mail system.
Leaving Messages at Other Extensions
You can leave inter-station or voice messages for other internal parties.
T o leave an inter-station or voice message for a busy IC extension:
1. Press (Message). HANG UP OR WAIT FOR MSG CENTER appears.
2. Do one of the following:
• Hang up to leave an inter-station message. MESSAGE LEFT FOR <name>
appears.
• Stay on the line to connect to the message center (usually voice mail).
T o leave an inter-station message without placing an internal call:
1. Dial 367 (Leave Message). LEAVE MESSAGE ON EXTENSION appears.
2. Enter the extension number. MESSAGE LEFT FOR <name> appears.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 39
Page 54
Messages
Viewing and Responding to Messages
When you have waiting messages, the (Message) button and Message/Ring Indicator flash
and the display shows the number of waiting messages.
NOTE
The display shows new messages as follows:
If your handset or speakerphone is off-hook when you view a inter-station
message, you automatically call the party who left the message.
• Inter-station messages sent by other internal parties are indicated by the party’s
programmed user name.
• Voice messages are indicated by FROM MBOX <your extension number>.
To view or respond to messag es:
1. With the handset on-hook, press (Message). Messages are displayed as first in/first
out. If there is more than one message, you can repeatedly press (Message) to
scroll through the messages.
2. When the desired message is displayed, press #, or lift the handset for privacy, and then
press # to respond. (If your handset is off-hook and you press (Message), you
automatically place a call to the party or message center who left the message.)
Canceling Messages Left at Other Extensions
You can cancel messages left at other extensions.
T o cancel a message left at another extension:
1. Dial 366. CANCEL MESSAGE ON EXT # appears.
2. Enter the extension number where you left the message. MESSAGE CANCELED FOR
<name> appears.
Deleting Waiting Inter-Station Messages
You can delete waiting inter-station messages.
NOTETo delete waiting voice messages, you must connect to your voice mailbox.
Model 5212/5224 User Guide – Issue 2, October 2008
Page 55
Using Do-Not-Disturb (DND)
You can use DND to stop calls and pages to your extension. When activated, internal calling
parties see your selected DND message. DND does not block queue callbacks, recalls, and
incoming external calls. The following table shows the 20 default DND messages. If your
system administrator changes your DND messages, you can record the new messages in the
“New Message” column for reference.
01Do-Not-Disturb11Out of Town ‘Til
02Leave a Message12Out of Office
03In Meeting Until13Out Until
04In Meeting14With a Client
05On Vacation/
Holiday ’Til
Messages
15With a Guest
06On Vacation/
Holiday
07Call Me At17In Conference
08At the Doctor18Away from Desk
09On a Trip19Gone Home
10On Break20Out to Lunch
You can enter a second line of text (up to 20 characters) for DND messages. For example, if
you select IN MEETING UNTIL, you can enter “3:30” on the second line. When other internal
parties try to call you, their displays show “IN MEETING UNTIL 3:30.”
• Press (Up) or (Down) to scroll through the messages.
• Enter the two-digit number for the DND message from the preceding table.
3. After selecting the message, enter the additional text for the DND description, if
applicable. See “Using the Dialpad Buttons to Enter Characters” on page 23 for dialpad
character descriptions.
4. Press
T o turn off DND:
Press the DND button. DO-NOT-DISTURB OFF appears.
(Speaker) or lift and replace the handset.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 41
Page 56
Messages
Using Reminder Messages
You can use Reminder Messages to alert you at a selected time, up to 24 hours in advance. At
the selected time, the Reminder Message signals you with eight short tones and your display
shows the message, even if you are on a call.
The following table shows the 20 default Reminder Messages. If your system administrator
changes your Reminder Messages, you can record the new messages in the “New Message”
column for reference.
1. With the handset on-hook, dial 305. SELECT REMINDER MESSAGE # (01-20) appears.
2. Do one of the following:
Default Mes-
sage
New Message
Code
Default Mes-
sage
New Message
• Enter the two-digit number for the message from the table above.
• Press (Up) or (Down) to scroll through the messages.
3. Press # to select the message.
4. Enter the time you wish to receive the message in hours and minutes (for example, 0900
or 900 for 9:00). Then press #. The display shows the Reminder Message state.
If your system is set for 24-hour format, you must enter the applicable time
(1400 = 2:00 P.M.).
If your system is set for 12-hour display format, press 1 for A.M. or 2 for P.M.
T o cancel all Reminder Message requests:
With the handset on-hook, dial 306. REMINDER MSGS CANCELED appears.
To clear a received Reminder Message:
With the handset on-hook, press
*.
Page 42Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 57
Paging Other System Users
You can place page announcements through endpoint speakers or external speakers (if
applicable). Y our system may use page zones to prevent announcements from transmitting
through every endpoint in the system. Each page zone contains a different combination of
extensions and external paging equipment.
Contact your system administrator for page zone information. You can use the following table to
save the page zone information for future reference.
Page Zone NameNumberDescription
Placing a Page Announcement
To place a page announcement:
1. Press 7.
2. Enter the page-zone number (0 to 9).
3. Wait for the tone, make your announcement, and then hang up.
Messages
Enabling or Disabling the Paging Feature
You can enable or disable the Page feature for your extension. If your extension is assigned to
more than one page zone, the Page on/off feature code enables or disables your extension for
all pages zone (you cannot select individual zones).
To enable or disable paging for your endpoint:
Dial 325 to enable paging. PAGE RECEIVE ON appears. Dial 325 again to disable
paging.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 43
Page 58
Page 59
Hunt Groups
Hunt groups are groups of internal parties (agents) who share a common (hunt group)
extension number. Calls can either be placed to the hunt group (using the hunt group extension
number) or to a specific agent (using the agent’s extension number). Hunt groups are
programmed by the system administrator.
Hunt groups types are either “UCD” or “ACD.”
• UCD Hunt Groups: Uniform Call Distribution (UCD) agents do not log in to the hunt group
to receive calls.
• ACD Hunt Groups: Automatic Call Distribution (ACD) agents log in to the ACD hunt group
to receive calls. Calls are distributed by either Agent IDs or extensions:
o Agent IDs: Each agent is assigned an Agent ID number for logging in to the hunt group
(see the next section). Hunt group calls are distributed to logged-in agents according to
their Agent ID number instead of their extension number. Agents can log in to any ACD
hunt group endpoint.
o Extensions: Hunt group members do not use Agent IDs, and calls are distributed to
endpoints where the agents are logged in.
Logging in to ACD Hunt Groups
You must log in to an ACD hunt group to receive hunt group calls. To stop calls, you either log
out of the ACD hunt group or divert calls. See “Diverting Hunt Group Calls” on page 47.
Hunt Groups
Only one agent can be logged in to an endpoint.
NOTES
To log in to or out of all ACD hunt groups in which you are a member:
If the ACD Agent ID Automatic Connect option is enabled for your hunt group and
you are using a headset, you are automatically connected to waiting calls when you
log in. The first call you receive after you log in rings until you answer it; however,
you are automatically connected to subsequent calls.
Dial 328 to log into an ACD hung group followed by your Agent ID, if necessary. AGENT
LOGGED INTO ALL ACDS appears. Dial 328 again to log out of an ACD hung group.
• Enter the ACD hunt group number.
• Press # to log in to all of your ACD hunt groups.
The display shows AGENT LOGIN AGENT ID.
3. Enter your Agent ID (if applicable), or press # if you do not have an agent ID. The
display shows the log in status for one or all hunt groups.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 45
Page 60
Hunt Groups
Logging out of ACD Hunt Groups
You can log out of all ACD hunt groups at once or log out of each hunt group one at a time.
T o log out of one or more ACD hunt group:
Do one of the following:
• Dial 328 to log out of all of your ACD hunt groups. The display shows AGENT
LOGGED OUT OF ALL ACDS.
• Dial 327 to log out of one hunt group at a time.
If you were logged in to only one hunt group, the display shows AGENT LOGGED
OUT OF HUNT GROUP <number>.
If you were logged in to more than one hunt group, the display shows AGENT
LOGOUT HG #. Enter the extension number of the ACD hunt group.
Stopping the ACD Hunt Group Wrap-up Timer
Each time you end an ACD hunt group call, a wrap-up timer starts. The default wrap-up time is
15 seconds. Your system administrator can change the wrap-up timer settings.
Until this timer expires, you will not receive another hunt group call; however, you can stop the
wrap-up timer to allow calls to your extension.
T o stop the wrap-up timer:
With the handset on-hook, dial 329. The display shows ACD WRAP-UP TERMINATED.
Page 46Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 61
Other Hunt Group Features
The following features can be used by ACD or UCD hunt groups.
Requesting Agent Help
You can use Agent Help to request help from a designated “Agent Help Extension” (usually your
supervisor) during a call. When your request call rings at the Agent Help Extension, the
supervisor can join the call or reject the request.
Hunt Groups
NOTE
T o use Agent Help:
1. While you are on a hunt group call, press (Special), and then dial
If you hear repeating tones, one of the following has occurred:
Agent Help is not supported on peer-to-peer (P2P) calls. Contact your system
administrator for more information.
• The feature is not available at your endpoint.
• You already have four parties in your call.
• Not enough system circuits are currently available.
• The Agent Help Extension is in DND.
If you hear repeating tones, one of the following has occurred:
• The feature is not availabl e at your endpoint.
NOTE
• You already have four parties in your call.
• Not enough system circuits are currently available.
• The Agent Help Extension is in DND.
2. If not preprogrammed, dial the Agent Help extension number.
If the Agent Help Extension accepts the call, AGENT HELP IN PROGRESS appears.
If the Agent Help Extension rejects the call, AGENT HELP REJECTED appears.
Diverting Hunt Group Calls
375.
You can temporarily divert hunt group calls, preventing hunt group calls to your extension.
To divert hunt group calls:
Dial 324 to divert calls. The display shows the feature state DIVERT HUNT GROUP
CALLS. Dial 324 again to accept calls.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 47
Page 62
Hunt Groups
Hunt Group Supervisor Features
The following features can be used by hunt group supervisors only.
Accepting or Rejecting Agent Help Calls
Supervisors can accept or reject Agent Help calls.
To accept an Agent Help request:
Answer as usual. Your microphone is automatically muted.
T o reject an Agent Help request:
Dial 376. AGENT HELP REJECTED appears.
Monitoring Calls
You can use Station Monitor to connect to a hunt-group call and hear both parties, but you
cannot be heard by either one. Station Monitor stops if the hunt group member terminates,
transfers, or transfers the call. You can barge-in or “steal” monitored calls, as described in the
following sections. You can also record the call. See “Using Record-A-Call” on page 34 for more
information about recording calls.
To use Station Monitor:
Dial 321, and then enter the extension number. MONITORING EXT <number> appears.
Monitored hunt group members may hear an “activation tone” when the feature is
activated.
Using Barge-in
While monitoring a hunt group call, you can use Barge-in to join the call.
To barge-in to a hunt-group call:
Dial 386. BARGE-IN PROGRESS appears.
Stealing Hunt Group Calls
While monitoring a hunt group call, you can “steal” the call from the hunt group member, which
disconnects the call from the agent and transfers the call to your extension.
To steal a hunt group call:
Dial 387. CALL STOLEN FROM EXT <number> appears.
Page 48Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008
Page 63
Troubleshooting
The following sections can help you solve problems that you may be experiencing with your
endpoint. Troubleshooting topics include:
• Contact Information: Information about system administrator contacts.
• Error Messages: Error messages and descriptions.
• Troubleshooting Tips: Possible problems and methods to solve them.
Contact Information
Your system administrator can help you with items such as changing your settings or modifying
endpoint features. System administrator duties include:
• Adding new user accounts.
• Setting the date and time.
• Programming System Speed-Dial numbers.
• Making database changes, such as changing user names and extension numbers.
Contact your system administrator with questions that are not covered in this user guide. If you
need further assistance, you can find provider information on the Mitel Web site
(www.mitel.com). All sales, service, and support are coordinated at the local level.
Troubleshooting
Error Messages
The following error messages may appear when using your endpoint.
CANNOT ACCESS FEATUREThe feature is enabled but other feature-related
CANNOT ACCESS RESERVED
FEATURE
INVALID FEATURE CODEThe feature code entered does not exist. Retry using
INVALID EXTENSION NUMBERThe extension number entered does not exist. Retry
NO UPDATE PERFORMEDThe feature was not completed or one or more feature
MessageReason
conditions were not met. Make sure that all featurerelated conditions are met and retry.
Y our system does not support the feature. Contact your
system administrator for more information.
the correct feature code (see page 13).
using a valid extension number.
conditions were not met.
Mitel® Model 5212/5224 User Guide – Issue 2, October 2008Page 49
Page 64
Troubleshooting
Troubleshooting Tips
The following table includes troubleshooting tips for endpoint and system features.
You can often correct problems that you may be experiencing by resetting th e
NOTE
The endpoint is not working properly. Contact your system administrator.
I cannot use one or more of the
features described in this guide.
endpoint to the default settings. See “Resetting the Endpoint to the Default
Settings” on page 17.
ProblemPossible Solution
The feature may not be enabled. Contact your system
administrator for more information.
I cannot program System Speed-Dial
numbers.
I cannot change the time and date on
the endpoint display.
Your system administrator programs System Speed
Dial numbers.
Y our system administrator programs the time and date.
Contact your system administrator if you notice that the
date and time are incorrect.
I am experiencing audio problems on
my endpoint such as echo, distorted
Contact your system administrator if you are having
audio problems.
sound, or choppiness.
The name on the display is incorrect. Your system administrator assigns display names.
I cannot use the local telephone
company star codes (for example,
*82, *69) when I press the Outgoing
button or use the Outgoing Call
access code (8 is the default code)
when calling an external number.
Rather than pressing the Outgoing button or 8 to
access an outside line, you must dial a Select Line
Group number before you can use the star codes. For
example, if your system is using the default Select Line
Group numbers, dial 92001 to access that line. After
you have dial tone, you can dial the star code and the
number.
I cannot use the Agent Help or
Record-a-Call features.
If your system uses Peer-to-Peer (P2P) audio, you
cannot use these features when you are on a P2P call.
Contact your system administrator for more
information.
I cannot program a Station SpeedDial number to the button I want.
Before assigning the speed-dial number to a
programmable button, you must store the number with
either a Station or System Speed-Dial code.
Page 50Mitel
®
Model 5212/5224 User Guide – Issue 2, October 2008