MCC SMLJ120A, SMLJ120C, SMLJ120CA, SMLJ12A, SMLJ100 Datasheet

M C C	omponents
	21201 Itasca Street Chatsworth
	! "#
	$% ! "#

Features

•For surface mount application in order to optimize board space

•Low inductance

•Low profile package

•Built-in strain relief

•Glass passivated junction

•Excellent clamping capability

•Repetition Rate( duty cycle): 0.5%

•Fast response time: typical less than 1ps from 0V to BV min

•Typical ID less than 1uA above 10V

•High temperature soldering: 250oC/10 seconds at terminals

•Plastic package has Underwrites Laboratory Flammability Classification 94V-O

Mechanical Data

•CASE: JEDEC DO-214AB molded plastic body over

passivated junction

•Terminals: solderable per MIL-STD-750, Method 2026

•Polarity: Color band denotes positive end( cathode) except

Bi-directional types.

•Standard packaging: 16mm tape per ( EIA 481).

•Weight: 0.007 ounce, 0.21 gram

Maximum Ratings @ 25oC Unless Otherwise Specified

Peak Pulse Current on	IPPM	See Table 1	Amps
10/1000us
waveform(Note1, Fig3)
Peak Pulse Power	PPPM	Minimum	Watts
Disspation on 10/1000us		3000
waveform(Note1,2,Fig1)
Peak forward surge	IFSM)	200.0	Amps
current (JEDEC
Method) (Note 2,3)		-55oC to
Operation And Storage	TJ,
Temperature Range	TSTG	+150oC

SMLJ5.0

THRU

SMLJ170CA

Transient

Voltage Suppressor

5.0 to 170 Volts

3000 Watt

DO-214AB (SMLJ) (LEAD FRAME)

											G
																									H
																	D
																											A																C
											F						E																			B
																						DIMENSIONS
									INCHES																		MM
DIM										MIN							MAX								MIN				MAX							NOTE
	A				.079										.103									2.00					2.62
	B				.115										.121									2.92					3.07
	C				.002										.008									0.051					0.203
	D				.006										.012									0.152					0.305
	E				.030										.050									0.76					1.27
	F				..305										.320									7.75					8.13
	G				.260										.280									6.60					7.11
	H				.220										.245									5.59					6.22

SUGGESTED SOLDER

PAD LAYOUT

0.280"

0.121”

0.060”

NOTES:

1.Non-repetitive current pulse per Fig.3 and derated above TA=25oC per Fig.2.

2.Mounted on 8.0mm2 copper pads to each terminal.

3.8.3ms, single half sine-wave or equivalent square wave, duty cycle=4 pulses per. Minutes maximum.

www.mccsemi.com

SMLJ5.0 thru SMLJ170CA

M C C

PPPM: PEAK PULSE POWER, KW

100				Non-Repetitive		)		100
						(I
						PP
				Pulse Waveform		CURRENTOR)		50
				Shown in Figure 3
				TA=25OC
10						POWERPULSE(P	DERATINGIN PERCENTAGE	75
0.1us	1.0us	10us	100us	0.1ms	1.0ms			0	25	50	75	100 125 150	175	200
1.0						PP
								25
0.1								0
		td, PULSE WIDTH, SEC				PEAK			TA, AMBIENT TEMPERATURE
Fig. 1-PEAL PULSE POWER VS PULSE.TIME									Fig. 2-PULSE RATING CURVE

IPPM, PEAK PULSE CURRENT-%

150		TA=25OC				10	4
												TJ =25OC
	tf=10usec	Pulse Width (td) is Defined			pF							F=1.0MHZ
		As the Point Where the Peak										Vsig=50mVP_P
	Peak Value	Current Decays to 50% of IPP			CAPACITANCE,
100
	IPPm					1000						Measured at
												Zero Bias
		Half Value-1/2Ipp
50			10/1000usec Waveform			100
			as Defined by R.E.A
					CJ,					Measured at
										Stand-Off
										Voltage (VMW)
0						10
0	1.0	2.0	3.0	4.0			5.0	10	20	50	100	200	500
		Tr, TIME, ms
								V (BR), BREAKDOWN VOLTAGE, VOLTS

Fig. 3-PULSE WAVEFORM	Fig. 4-TYPICAL CAPACITANCE VS STAND-OFF
	VOLTAGE

FORWARD SURGE CURRENT	AMPERES
, PEAK
FSM
I

200

100

TJ =TJ max

50 8.3ms Single Half Since-Wave Vsig=50mVP_P

UNIDIRECTIONAL ONLY

10

1 5 10 50 100

NUMBER OF CYCLES AT 60HZ

Fig-5MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CUTTENT

www.mccsemi.com

									M C C
SMLJ5.0 THRU SMLJ170CA
Electrical Characteristics @ 25oC Unless Otherwise Specified
									MAXIMUM
	REVERSE								REVERSE
	STAND-OFF	BREAKDOWN VOLTAGE			MAXIMUM		PEAK PULSE		LEAKAGE
MCC PART	VOLTAGE		V(BR) @IT		CLAMPING		CURRENT		@VWM
NUMBER	VWM		(VOLTS)		VOLTAGE@IPP		IPP		ID	MARKING
	VOLTS	MIN	MAX	IT(mA)	VOLTS		(AMPS)		(uA)	CODE
SMLJ5.0	5.0	6.40	7.30	10	9.6		312.5		1000	HDD
SMLJ5.0A	5.0	6.40	7.00	10	9.2		326.0		1000	HDE
SMLJ6.0	6.0	6.67	8.15	10	11.4		263.2		1000	HDF
SMLJ6.0A	6.0	6.67	7.37	10	10.3		291.3		1000	HDG
SMLJ6.5	6.5	7.22	8.82	10	12.3		243.9		500	HDH
SMLJ6.5A	6.5	7.22	7.98	10	11.2		267.9		500	HDK
SMLJ7.0	7.0	7.78	9.51	10	13.3		225.6		200	HDL
SMLJ7.0A	7.0	7.78	8.60	10	12.0		250.0		200	HDM
SMLJ7.5	7.5	8.33	10.2	1	14.3		209.8		100	HDN
SMLJ7.5A	7.5	8.33	9.21	1	12.9		232.6		100	HDP
SMLJ8.0	8.0	8.89	10.9	1	15.0		200.0		50	HDQ
SMLJ8.0A	8.0	8.89	9.83	1	13.6		220.6		50	HDR
SMLJ8.5	8.5	9.44	11.5	1	15.9		118.8		25	HDS
SMLJ8.5A	8.5	9.44	10.4	1	14.4		208.4		25	HDT
SMLJ9.0	9.0	10.0	12.2	1	16.9		177.4		10	HDU
SMLJ9.0A	9.0	10.0	11.1	1	15.4		194.8		10	HDV
SMLJ10	10	11.1	13.6	1	18.8		159.6		5	HDW
SMLJ10A	10	11.1	12.3	1	17.0		176.4		5	HDX
SMLJ11	11	12.2	14.9	1	20.1		149.2		5	HDY
SMLJ11A	11	12.2	13.5	1	18.2		164.8		5	HDZ
SMLJ12	12	13.3	16.3	1	22.0		136.4		5	HED
SMLJ12A	12	13.3	14.7	1	19.9		150.6		5	HEE
SMLJ13	13	14.4	17.6	1	23.8		126.0		5	HEF
SMLJ13A	13	14.4	15.5	1	21.5		139.4		5	HEG
SMLJ14	14	15.6	19.1	1	25.8		116.2		5	HEH
SMLJ14A	14	15.6	17.2	1	23.2		129.4		5	HEK
SMLJ15	15	16.7	20.4	1	26.9		111.6		5	HEL
SMLJ15A	15	16.7	18.5	1	24.4		123.0		5	HEM
SMLJ16	16	17.8	21.8	1	28.8		104.2		5	HEN
SMLJ16A	16	17.8	19.7	1	26.0		115.4		5	HEP
SMLJ17	17	18.9	23.1	1	30.5		98.4		5	HEQ
SMLJ17A	17	18.9	20.9	1	27.6		106.6		5	HER
SMLJ18	18	20.0	24.4	1	32.2		93.2		5	HES
SMLJ18A	18	20.0	22.1	1	29.2		102.8		5	HET
SMLJ20	20	22.2	27.1	1	35.8		83.8		5	HEU
SMLJ20A	20	22.2	24.5	1	32.4		92.6		5	HEV
SMLJ22	22	24.4	29.8	1	39.4		76.2		5	HEW
SMLJ22A	22	24.4	26.9	1	35.5		84.4		5	HEX
SMLJ24	24	26.7	32.6	1	43.0		69.8		5	HEY
SMLJ24A	24	26.7	29.5	1	38.9		77.2		5	HEZ
SMLJ26	26	28.9	35.3	1	46.6		64.4		5	HFD
SMLJ26A	26	28.9	31.9	1	42.1		71.2		5	HFE

www.mccsemi.com