Makita MT901, MT900 Manual

INSTRUCTION MANUAL

Angle Grinder

MT900

MT901

006770

DOUBLE INSULATION

WARNING:

For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

ENGLISH

SPECIFICATIONS

Model	MT900	MT901
Depressed center wheel diameter	180 mm	230 mm
Spindle thread	M14	M14
No load speed (min-1)	8,500	6,600
Overall length	468 mm	468 mm
Net weight	4.7 kg	4.7 kg
Safety class		/II

•Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

•Note: Specifications may differ from country to country.

END202-2

Symbols

The following show the symbols used for the equipment. Be sure that you understand their meaning before use. Read instruction manual.

DOUBLE INSULATION

Wear safety glasses.

Only for EU countries

Do not dispose of electric equipment together with household waste material! In observance of European Directive 2002/96/EC on waste electric and electronic equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

ENE048-1

Intended use

The tool is intended for grinding, sanding and cutting of metal and stone materials without the use of water.

ENF002-1

Power supply

The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire.

ENG021-1

For European countries only Noise and Vibration

The typical A-weighted noise levels are sound pressure level: 90 dB (A)

sound power level: 103 dB (A)

Wear ear protection.

The typical weighted root mean square acceleration

value is not more than 2.5 m/s2.

These values have been obtained according to EN50144.

ENH001-6

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in compliance with the following standards of standardized documents;

EN50144, EN55014, EN61000 in accordance with Council Directives, 89/336/EEC, 98/37/EC.

Yasuhiko Kanzaki CE2006

000087

Director

MAKITA INTERNATIONAL EUROPE LTD.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, ENGLAND

Responsible manufacturer:

Makita Corporation Anjo Aichi Japan

ENA001-2

SAFETY INSTRUCTIONS

WARNING! When using electric tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury. Read all these instructions before operating this product and save these instructions.

For safe operations:

1.Keep work area clean.

Cluttered areas and benches invite injuries.

2.Consider work area environment.

Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area well lit. Do not use power tools where there is risk to cause fire or explosion.

3.Guard against electric shock.

Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators, ranges, refrigerators).

2

4.Keep children away.

Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area.

5.Store idle tools.

When not in use, tools should be stored in a dry, high or locked up place, out of reach of children.

6.Do not force the tool.

It will do the job better and safer at the rate for which it was intended.

7.Use the right tool.

Do not force small tools or attachments to do the job of a heavy duty tool. Do not use tools for purposes not intended; for example, do not use circular saws to cut tree limbs or logs.

8.Dress properly.

Do not wear loose clothing or jewellery, they can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protecting hair covering to contain long hair.

9.Use safety glasses and hearing protection.

Also use face or dust mask if the cutting operation is dusty.

10.Connect dust extraction equipment.

If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used.

11.Do not abuse the cord.

Never carry the tool by the cord or yank it to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges.

12.Secure work.

Use clamps or a vice to hold the work. It is safer than using your hand and it frees both hands to operate the tool.

13.Do not overreach.

Keep proper footing and balance at all times.

14.Maintain tools with care.

Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories. Inspect tool cord periodically and if damaged have it repaired by an authorized service facility. Inspect extension cords periodically and replace, if damaged. Keep handles dry, clean and free from oil and grease.

15.Disconnect tools.

When not in use, before servicing and when changing accessories such as blades, bits and cutters.

16.Remove adjusting keys and wrenches.

Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.

17.Avoid unintentional starting.

Do not carry a plugged-in tool with a finger on the

switch. Ensure switch is off when plugging in.

18.Use outdoor extension leads.

When tool is used outdoors, use only extension cords intended for outdoor use.

19.Stay alert.

Watch what you are doing. Use common sense. Do not operate tool when you are tired.

20.Check damaged parts.

Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this instruction manual. Have defective switches replaced by an authorized service facility. Do not use the tool if the switch does not turn it on and off.

21.Warning.

The use of any accessory or attachment, other than those recommended in this instruction manual or the catalog, may present a risk of personal injury.

22.Have your tool repaired by a qualified person.

This electric tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts, otherwise this may result in considerable danger to the user.

ENB031-6

ADDITIONAL SAFETY RULES

1.Always use eye and ear protection. Other personal protective equipment such as dust mask, gloves, helmet and apron should be worn.

2.Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

3.Keep guards in place.

4.Use only wheels with correct size and wheels having a maximum operating speed at least as high as the highest No Load Speed marked on the tool's nameplate. When using depressed center wheels, be sure to use only fiberglass-reinforced wheels.

5.Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately.

6.Observe the instructions of the manufacturer for correct mounting and use of wheels.

3