Kubota L3130, L3430, L3830, L4330, L4630 Shop manual

WORKSHOP MANUAL

TRACTOR

L3130,L3430,L3830,

L4330,L4630,L5030

KiSC issued 06, 2006 A

TO THE READER

This Workshop Manual has been prepared to provide servicing personnel with information on the mechanism, service and maintenance of KUBOTA Tractor L3130, L3430, L3830, L4330, L4630 and L5030. It is divided into two parts, “Mechanism” and “Servicing” for each section.

■ Mechanism

Information on the construction and function are included. This part should be understood before proceeding with troubleshooting, disassembling and servicing.

Refer to Diesel engine / Tractor Mechanism Workshop Manual (Code No. 9789701872 / 97897-18200) for the one which has not been described to this workshop manual.

■Servicing

The heading “General” includes general precautions, check and maintenance and

special tools. Other section, there are troubleshooting, servicing specification lists, checking and adjusting, disassembling and assembling, and servicing which cover procedures, precautions, factory specifications and allowable limits.

All information illustrations and specifications contained in this manual are based on the latest product information available at the time of publication.

The right is reserved to make changes in all information at any time without notice.

October 2002

© KUBOTA Corporation 2002

KiSC issued 06, 2006 A

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

SAFETY INSTRUCTIONS

SAFETY FIRST

This symbol, the industry’s “Safety Alert Symbol”, is used throughout this manual and on labels on the machine itself to warn of the possibility of personal injury. Read these instructions carefully.

It is essential that you read the instructions and safety regulations before you attempt to repair or use this unit.

	DANGER	: Indicates an imminently hazardous situation which, if not avoided, will result in
		death or serious injury.
	WARNING	: Indicates a potentially hazardous situation which, if not avoided, could result in
		death or serious injury.
	CAUTION	: Indicates a potentially hazardous situation which, if not avoided, may result in
		minor or moderate injury.
	■ IMPORTANT	: Indicates that equipment or property damage could result if instructions are not
		followed.
	■ NOTE	: Gives helpful information.
			BEFORE SERVICING AND REPAIRING
			• Read all instructions and safety instructions in this
			manual and on your machine safety decals.
			• Clean the work area and machine.
			• Park the machine on a firm and level ground, and set
			the parking brake.
			• Lower the implement to the ground.
			• Stop the engine, and remove the key.
			• Disconnect the battery negative cable.
			• Hang a “DO NOT OPERATE” tag in operator
			station.

KiSC issued 06, 2006 A

1

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM	SAFETY INSTRUCTIONS

SAFETY STARTING

•Do not start the engine by shorting across starter terminals or bypassing the safety start switch.

•Do not alter or remove any part of machine safety system.

•Before starting the engine, make sure that all shift levers are in neutral positions or in disengaged positions.

•Never start the engine while standing on ground. Start the engine only from operator’s seat.

SAFETY WORKING

•Do not work on the machine while under the influence of alcohol, medication, or other substances or while fatigued.

•Wear close fitting clothing and safety equipment appropriate to the job.

•Use tools appropriate to the work. Makeshift tools, parts, and procedures are not recommended.

•When servicing is performed together by two or more persons, take care to perform all work safely.

•Do not work under the machine that is supported solely by a jack. Always support the machine by safety stands.

•Do not touch the rotating or hot parts while the engine is running.

•Never remove the radiator cap while the engine is running, or immediately after stopping. Otherwise, hot water will spout out from radiator. Only remove radiator cap when cool enough to touch with bare hands. Slowly loosen the cap to first stop to relieve pressure before removing completely.

•Escaping fluid (fuel or hydraulic oil) under pressure can penetrate the skin causing serious injury. Relieve pressure before disconnecting hydraulic or fuel lines. Tighten all connections before applying pressure.

AVOID FIRES

•Fuel is extremely flammable and explosive under certain conditions. Do not smoke or allow flames or sparks in your working area.

•To avoid sparks from an accidental short circuit, always disconnect the battery negative cable first and connect it last.

•Battery gas can explode. Keep sparks and open flame away from the top of battery, especially when charging the battery.

•Make sure that no fuel has been spilled on the engine.

KiSC issued 06, 2006 A

2

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

SAFETY INSTRUCTIONS

VENTILATE WORK AREA

• If the engine must be running to do some work, make sure the area is well ventilated. Never run the engine in a closed area. The exhaust gas contains poisonous carbon monoxide.

PREVENT ACID BURNS

• Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin, clothing and cause blindness if splashed into eyes. Keep electrolyte away from eyes, hands and clothing. If you spill electrolyte on yourself, flush with water, and get medical attention immediately.

DISPOSE OF FLUIDS PROPERLY

• Do not pour fluids into the ground, down a drain, or into a stream, pond, or lake. Observe relevant environmental protection regulations when disposing of oil, fuel, coolant, electrolyte and other harmful waste.

PREPARE FOR EMERGENCIES

• Keep a first aid kit and fire extinguisher handy at all times.

• Keep emergency numbers for doctors, ambulance service, hospital and fire department near your telephone.

KiSC issued 06, 2006 A

3

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM	SAFETY INSTRUCTIONS

SAFETY DECALS

The following safety decals are installed on the machine.

If a decal becomes damaged, illegible or is not on the machine, replace it. The decal part number is listed in the parts list.

KiSC issued 06, 2006 A

4

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM	SAFETY INSTRUCTIONS

KiSC issued 06, 2006 A

5

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM	SAFETY INSTRUCTIONS

KiSC issued 06, 2006 A

6

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM	SAFETY INSTRUCTIONS

KiSC issued 06, 2006 A

7

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM SPECIFICATIONS

SPECIFICATIONS

L3130

Model

Manual

GST

HST

2WD (ROPS)

4WD (ROPS)

4WD (ROPS)

4WD (ROPS)

Model

D1503-MA-E-GST / D1503-MA-E2-GST

D1503-MA-E-HST /

D1503-MA-E2-HST

Type

Indirect injection vertical, water-cooled, 4-cycle diesel

Number of cylinders

3

Total displacement

1.499 L (91.5 cu.in.)

Engine

Bore and stroke

83 × 92.4 mm (3.3 × 3.6 in.)

Net power

23.1 kW (31.0 HP)*

PTO power

19.0 kW (25.5 HP)* / 2700 min

−1

(rpm)

17.9 kW (24.0 HP)* /

(factory observe)

2700 min−1 (rpm)

Maximum torque

102.9 N·m (10.5 kgf·m, 75.9 ft-lbs)

Battery capacity

12 V, RC : 123 min, CCA : 490 A

Fuel

Diesel fuel No. 1 [below −10 °C (14 °F], Diesel fuel No. 2-D [above −10 °C (14 °F)]

Fuel tank

40 L (10.6 U.S.gals., 8.8 Imp.gals.)

Engine crankcase

5.7 L (6.0 U.S.qts., 5.0 Imp.qts.)

Capacities

(with filter)

Engine coolant

6.0 L (6.3 U.S.qts., 5.3 Imp.qts.)

Transmission case

42 L (11.1 U.S.gals., 9.2 Imp.gals.)

Overall length

2915 mm (114.8 in.)

(without 3P)

Overall width (min. tread)

1520 mm (59.8 in.)

Overall height (with ROPS

2305 mm (90.7 in.) / 2140 mm (84.3 in.)

foldable / rigid)

Dimensions

Wheel base

1810 mm (71.3 in.)

1805 mm (71.1 in.)

Min. ground clearance

360 mm (14.2 in.)

1310 mm (51.6 in.)

Front

1410 mm (55.5 in.)

1155 mm (45.5 in.)

Tread

1510 mm (59.4 in.)

1610 mm (63.4 in.)

Rear

1200 mm (47.2 in.), 1300 mm (51.2 in.), 1385 mm (54.5 in.), 1480 mm (58.3 in.)

Weight (with ROPS)

1415 kg (3120 lbs)

1460 kg (3220 lbs)

1480 kg (3265 lbs)

1500 kg (3305 lbs)

Standard

Front

6-16

7.2-16

tire size

Rear

12.4-24

Clutch

Dry type single stage

Travelling

Steering

Hydrostatic power steering

system

F8, R8 fully synchronized main and shuttle

F12, R8 Glide shift

Hydrotstatic

Transmission

transmission

transmission

transmission

(3 speeds)

Braking system

Wet disk type

Min. turning radius

2.6 m (8.5 feet)

2.7 m (8.9 feet)

(with brake)

Hydraulic control system

Position control

Pump capacity

31.5 L (8.3 U.S.gals., 6.9 Imp.gals.) / min.

Hydraulic

Three point hitch

SAE Category I

system

Max. lift

At lift points

1700 kg (3750 lbs)

24 in. behind

force

1200 kg (2650 lbs)

lift points

System pressure

17.1 to 18.1 MPa (175 to 185 kgf/cm2, 2491 to 2633 psi)

Rear PTO

SAE 1-3/8, 6 splines

PTO / Engine speed

540 min

−1

(rpm) / 2550 min

−1

(rpm)

540 min−1 (rpm) /

PTO

2640 min−1 (rpm)

Mid-PTO (if equipped)

USA No. 5 (KUBOTA 10-tooth) involute spline

PTO / Engine speed

2000 min

−1

(rpm) / 2580 min

−1

(rpm)

2000 min−1 (rpm) /

2670 min−1 (rpm)

Note : * Manufacture’s estimate

The company reserves the right to change the specifications without notice.

W10281170

KiSC issued 06, 2006 A

8

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM										SPECIFICATIONS
							L3430
Model				Manual		GST		HST
				4WD (ROPS)		4WD (ROPS)		4WD (ROPS)		4WD (CABIN)
	Model			D1703-MA-E-GST / D1703-MA-E2-GST				D1703-MA-E-HST / D1703-MA-E2-HST
	Type				Indirect injection vertical, water-cooled, 4-cycle diesel
	Number of cylinders						3
	Total displacement					1.647 L (100.5 cu.in.)
	Bore and stroke					87 × 92.4 mm (3.4 × 3.6 in.)
Engine
	Net power					25.1 kW (33.6 HP)*
	PTO power			21.3 kW (28.5 HP)* / 2700 min−1 (rpm)				20.1 kW (27.0 HP)* / 2700 min−1 (rpm)
	(factory observe)
	Maximum torque					108.3 N·m (11.05 kgf·m, 79.9 ft-lbs)
	Battery capacity					12 V, RC : 123 min, CCA : 490 A
	Fuel			Diesel fuel No. 1 [below −10 °C (14 °F], Diesel fuel No. 2-D [above −10 °C (14 °F)]
	Fuel tank					40 L (10.6 U.S.gals., 8.8 Imp.gals.)
	Engine crankcase					5.7 L (6.0 U.S.qts., 5.0 Imp.qts.)
Capacities	(with filter)
	Engine coolant					6.0 L (6.3 U.S.qts., 5.3 Imp.qts.)
	Transmission case					42 L (11.1 U.S.gals., 9.2 Imp.gals.)
	Overall length					2915 mm (114.8 in.)
	(without 3P)
	Overall width (min. tread)					1520 mm (59.8 in.)
	Overall height
	(with CABIN or ROPS			2305 mm (90.7 in.) / 2140 mm (84.3 in.)						2195 mm (86.4 in.)
Dimensions	foldable / rigid)
	Wheel base					1805 mm (71.1 in.)
	Min. ground clearance					360 mm (14.2 in.)
	Tread		Front			1155 mm (45.5 in.)
			Rear	1200 mm (47.2 in.), 1300 mm (51.2 in.), 1385 mm (54.5 in.), 1480 mm (58.3 in.)
Weight (with ROPS or CABIN)				1460 kg (3220 lbs)		1480 kg (3265 lbs)		1500 kg (3305 lbs)		1650 kg (3638 lbs)
	Standard		Front				7.2-16
	tire size		Rear		12.4-24
	Clutch					Dry type single stage
	Steering					Hydrostatic power steering
Travelling
				F8, R8 fully
system	Transmission			synchronized main		F12, R8 Glide shift		Hydrotstatic transmission
				and shuttle		transmission		(3 speeds)
				transmission
	Braking system					Wet disk type
	Min. turning radius					2.7 m (8.9 feet)
	(with brake)
	Hydraulic control system					Position control
	Pump capacity					31.5 L (8.3 U.S.gals., 6.9 Imp.gals.) / min.
Hydraulic	Three point hitch					SAE Category I
system	Max. lift		At lift points			1700 kg (3750 lbs)
			24 in. behind
	force					1200 kg (2650 lbs)
			lift points
	System pressure				17.1 to 18.1 MPa (175 to 185 kgf/cm2, 2491 to 2633 psi)
	Rear PTO					SAE 1-3/8, 6 splines
PTO	PTO / Engine speed			540 min−1 (rpm) / 2550 min−1 (rpm)				540 min−1 (rpm) / 2640 min−1 (rpm)
	Mid-PTO (if equipped)					USA No. 5 (KUBOTA 10-tooth) involute spline
	PTO / Engine speed			2000 min−1 (rpm) / 2580 min−1 (rpm)				2000 min−1 (rpm) / 2670 min−1 (rpm)

Note : * Manufacture’s estimate

The company reserves the right to change the specifications without notice.

W10357910

KiSC issued 06, 2006 A

9

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

SPECIFICATIONS

L3830

Model

Manual

GST

HST

2WD (ROPS)

4WD (ROPS)

4WD (ROPS)

4WD (ROPS)

Model

D1803-M-E-GST / D1803-M-E2-GST

D1803-M-E-HST /

D1803-M-E2-HST

Type

Indirect injection vertical, water-cooled, 4-cycle diesel

Number of cylinders

3

Total displacement

1.826 L (111.4 cu.in.)

Engine

Bore and stroke

87 × 102.4 mm (3.4 × 4.0 in.)

Net power

27.9 kW (37.4 HP)*

PTO power

23.9.0 kW (32.0 HP)* / 2700 min

−1

(rpm)

22.8 kW (30.5 HP)* /

(factory observe)

2700 min−1 (rpm)

Maximum torque

120.7 N·m (12.3 kgf·m, 89.0 ft-lbs)

Battery capacity

12 V, RC : 133 min, CCA : 582 A

Fuel

Diesel fuel No. 1 [below −10 °C (14 °F], Diesel fuel No. 2-D [above −10 °C (14 °F)]

Fuel tank

40 L (10.6 U.S.gals., 8.8 Imp.gals.)

Engine crankcase

6.7 L (7.1 U.S.qts., 5.9 Imp.qts.)

Capacities

(with filter)

Engine coolant

7.5 L (7.9 U.S.qts., 6.6 Imp.qts.)

Transmission case

43 L (11.4 U.S.gals., 9.5 Imp.gals.)

Overall length

2985 mm (117.5 in.)

(without 3P)

Overall width (min. tread)

1690 mm (66.5 in.)

Overall height (with ROPS

2315 mm (91.1 in.) / 2155 mm (84.8 in.)

foldable / rigid)

Dimensions

Wheel base

1845 mm (72.6 in.)

1840 mm (72.4 in.)

Min. ground clearance

375 mm (14.8 in.)

1310 mm (51.6 in.)

Front

1410 mm (55.5 in.)

1155 mm (45.5 in.)

Tread

1510 mm (59.4 in.)

1610 mm (63.4 in.)

Rear

1285 mm (50.6 in.), 1435 mm (56.5 in.), 1530 mm (60.2 in.)

Weight (with ROPS)

1430 kg (3155 lbs)

1480 kg (3265 lbs)

1495 kg (3295 lbs)

1515 kg (3340 lbs)

Standard

Front

6-16

8.3-16

tire size

Rear

14.9-24

Clutch

Dry type single stage

Travelling

Steering

Hydrostatic power steering

system

F8, R8 fully synchronized main and shuttle

F12, R8 Glide shift

Hydrotstatic

Transmission

transmission

transmission

transmission

(3 speeds)

Braking system

Wet disk type

Min. turning radius

2.6 m (8.5 feet)

2.7 m (8.9 feet)

(with brake)

Hydraulic control system

Position control

Pump capacity

31.5 L (8.3 U.S.gals., 6.9 Imp.gals.) / min.

Hydraulic

Three point hitch

SAE Category I

system

Max. lift

At lift points

1750 kg (3860 lbs)

24 in. behind

force

1250 kg (2760 lbs)

lift points

System pressure

17.1 to 18.1 MPa (175 to 185 kgf/cm2, 2491 to 2633 psi)

Rear PTO

SAE 1-3/8, 6 splines

PTO / Engine speed

540 min

−1

(rpm) / 2550 min

−1

(rpm)

540 min−1 (rpm) /

PTO

2640 min−1 (rpm)

Mid-PTO (if equipped)

USA No. 5 (KUBOTA 10-tooth) involute spline

PTO / Engine speed

2000 min

−1

(rpm) / 2580 min

−1

(rpm)

2000 min−1 (rpm) /

2670 min−1 (rpm)

Note : * Manufacture’s estimate

The company reserves the right to change the specifications without notice.

W10375160

KiSC issued 06, 2006 A

10

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM										SPECIFICATIONS
							L4330
Model				Manual		GST		HST
				4WD (ROPS)		4WD (ROPS)		4WD (ROPS)		4WD (CABIN)
	Model			V2203-MA-E-GST / V2203-MA-E2-GST				V2203-MA-E-HST / V2203-MA-E2-HST
	Type				Indirect injection vertical, water-cooled, 4-cycle diesel
	Number of cylinders						4
	Total displacement					2.197 L (134.1 cu.in.)
	Bore and stroke					87 × 92.4 mm (3.4 × 3.6 in.)
Engine
	Net power					30.6 kW (41.0 HP)*
	PTO power			26.9 kW (36.0 HP)* / 2600 min−1 (rpm)				25.7 kW (34.5 HP)* / 2600 min−1 (rpm)
	(factory observe)
	Maximum torque					146.2 N·m (14.9 kgf·m, 107.8 ft-lbs)
	Battery capacity					12 V, RC : 133 min, CCA : 582 A
	Fuel			Diesel fuel No. 1 [below −10 °C (14 °F], Diesel fuel No. 2-D [above −10 °C (14 °F)]
	Fuel tank					40 L (10.6 U.S.gals., 8.8 Imp.gals.)
	Engine crankcase					8.2 L (8.7 U.S.qts., 7.2 Imp.qts.)
Capacities	(with filter)
	Engine coolant					7.5 L (7.9 U.S.qts., 6.6 Imp.qts.)
	Transmission case					43 L (11.4 U.S.gals., 9.5 Imp.gals.)
	Overall length					3080 mm (121.3 in.)
	(without 3P)
	Overall width (min. tread)					1690 mm (66.5 in.)
	Overall height
	(with CABIN or ROPS			2315 mm (91.1 in.) / 2155 mm (84.8 in.)						2210 mm (87.0 in.)
Dimensions	foldable / rigid)
	Wheel base					1895 mm (74.6 in.)
	Min. ground clearance					375 mm (14.8 in.)
	Tread		Front			1300 mm (51.2 in.)
			Rear	1285 mm (50.6 in.), 1435 mm (56.5 in.), 1530 mm (60.2 in.)
Weight (with ROPS or CABIN)				1560 kg (3440 lbs)		1575 kg (3470 lbs)		1600 kg (3525 lbs)		1750 kg (3858 lbs)
	Standard		Front				8.3-16
	tire size		Rear		14.9-24
	Clutch					Dry type single stage
	Steering					Hydrostatic power steering
Travelling
				F8, R8 fully
system	Transmission			synchronized main		F12, R8 Glide shift		Hydrotstatic transmission
				and shuttle		transmission		(3 speeds)
				transmission
	Braking system					Wet disk type
	Min. turning radius					2.7 m (8.9 feet)
	(with brake)
	Hydraulic control system					Position control
	Pump capacity					35.6 L (9.4 U.S.gals., 7.8 Imp.gals.) / min.
Hydraulic	Three point hitch					SAE Category I
system	Max. lift		At lift points			1750 kg (3860 lbs)
			24 in. behind
	force					1250 kg (2760 lbs)
			lift points
	System pressure				18.1 to 19.1 MPa (185 to 195 kgf/cm2, 2633 to 2775 psi)
	Rear PTO					SAE 1-3/8, 6 splines
PTO	PTO / Engine speed			540 min−1 (rpm) / 2550 min−1 (rpm)				540 min−1 (rpm) / 2440 min−1 (rpm)
	Mid-PTO (if equipped)					USA No. 5 (KUBOTA 10-tooth) involute spline
	PTO / Engine speed			2000 min−1 (rpm) / 2580 min−1 (rpm)				2000 min−1 (rpm) / 2470 min−1 (rpm)

Note : * Manufacture’s estimate

The company reserves the right to change the specifications without notice.

W10388600

KiSC issued 06, 2006 A

11

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

SPECIFICATIONS

L4630

Model

Manual

GST

HST

4WD (ROPS)

4WD (ROPS)

4WD (CABIN)

4WD (ROPS)

Model

V2203-MB-E-GST / V2203-MB-E2-GST

V2203-MB-E-HST /

V2203-MB-E2-HST

Type

Indirect injection vertical, water-cooled, 4-cycle diesel

Number of cylinders

4

Total displacement

2.197 L (134.1 cu.in.)

Engine

Bore and stroke

87 × 92.4 mm (3.4 × 3.6 in.)

Net power

33.3 kW (44.7 HP)*

PTO power

29.5 kW (39.5 HP)* / 2700 min

−1

(rpm)

28.3 kW (38.0 HP)* /

(factory observe)

2700 min−1 (rpm)

Maximum torque

146.2 N·m (14.9 kgf·m, 107.8 ft-lbs)

Battery capacity

12 V, RC : 133 min, CCA : 582 A

Fuel

Diesel fuel No. 1 [below −10 °C (14 °F], Diesel fuel No. 2-D [above −10 °C (14 °F)]

Fuel tank

40 L (10.6 U.S.gals., 8.8 Imp.gals.)

Engine crankcase

8.2 L (8.7 U.S.qts., 7.2 Imp.qts.)

Capacities

(with filter)

Engine coolant

7.5 L (7.9 U.S.qts., 6.6 Imp.qts.)

Transmission case

43 L (11.4 U.S.gals., 9.5 Imp.gals.)

Overall length

3080 mm (121.3 in.)

(without 3P)

Overall width (min. tread)

1690 mm (66.5 in.)

Overall height

2315 mm (91.1 in.) /

(with CABIN or ROPS

2315 mm (91.1 in.) / 2155 mm (84.8 in.)

2210 mm (87.0 in.)

2155 mm (84.8 in.)

Dimensions

foldable / rigid)

Wheel base

1895 mm (74.6 in.)

Min. ground clearance

375 mm (14.8 in.)

Tread

Front

1300 mm (51.2 in.)

Rear

1285 mm (50.6 in.), 1435 mm (56.5 in.), 1530 mm (60.2 in.)

Weight (with ROPS or CABIN)

1560 kg (3440 lbs)

1575 kg (3470 lbs)

1730 kg (3815 lbs)

1600 kg (3525 lbs)

Standard

Front

8.3-16

tire size

Rear

14.9-24

Clutch

Dry type single stage

Steering

Hydrostatic power steering

Travelling

F8, R8 fully

Hydrotstatic

system

synchronized main

Transmission

F12, R8 Glide shift transmission

transmission

and shuttle

(3 speeds)

transmission

Braking system

Wet disk type

Min. turning radius

2.7 m (8.9 feet)

(with brake)

Hydraulic control system

Position control

Pump capacity

37.0 L (9.8 U.S.gals., 8.1 Imp.gals.) / min.

Hydraulic

Three point hitch

SAE Category I

system

Max. lift

At lift points

1750 kg (3860 lbs)

24 in. behind

force

1250 kg (2760 lbs)

lift points

System pressure

18.1 to 19.1 MPa (185 to 195 kgf/cm2, 2633 to 2775 psi)

Rear PTO

SAE 1-3/8, 6 splines

PTO / Engine speed

540 min

−1

(rpm) / 2550 min

−1

(rpm)

540 min−1 (rpm) /

PTO

2640 min−1 (rpm)

Mid-PTO (if equipped)

USA No. 5 (KUBOTA 10-tooth) involute spline

PTO / Engine speed

2000 min

−1

(rpm) / 2580 min

−1

(rpm)

2000 min−1 (rpm) /

2670 min−1 (rpm)

Note : * Manufacture’s estimate

The company reserves the right to change the specifications without notice.

W10400750

KiSC issued 06, 2006 A

12

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

SPECIFICATIONS

L5030

Model

GST

HST

4WD (ROPS)

4WD (ROPS)

4WD (CABIN)

Model

V2403-MA-E-GST /

V2403-MA-E-HST / V2403-MA-E2-HST

V2403-MA-E2-GST

Type

Indirect injection vertical, water-cooled, 4-cycle diesel

Number of cylinders

4

Total displacement

2.434 L (148.5 cu.in.)

Engine

Bore and stroke

87 × 102.4 mm (3.4 × 4.0 in.)

Net power

37.3 kW (50.0 HP)*

PTO power

32.8 kW (44.0 HP)* /

31.7 kW (42.5 HP)* / 2700 min

−1

(rpm)

(factory observe)

2700 min−1 (rpm)

Maximum torque

162.4 N·m (16.6 kgf·m, 119.8 ft-lbs)

Battery capacity

12 V, RC : 133 min, CCA : 582 A

Fuel

Diesel fuel No. 1 [below −10 °C (14 °F], Diesel fuel No. 2-D [above −10 °C (14 °F)]

Fuel tank

43 L (11.4 U.S.gals., 9.5 Imp.gals.)

Engine crankcase

8.2 L (8.7 U.S.qts., 7.2 Imp.qts.)

Capacities

(with filter)

Engine coolant

8.0 L (8.5 U.S.qts., 7.0 Imp.qts.)

Transmission case

45 L (11.9 U.S.gals., 9.9 Imp.gals.)

Overall length

3205 mm (126.2 in.)

(without 3P)

Overall width (min. tread)

1710 mm (67.3 in.)

Overall height

(with CABIN or ROPS

2355 mm (92.7 in.) / 2190 mm (86.2 in.)

2270 mm (89.4 in.)

Dimensions

foldable / rigid)

Wheel base

1915 mm (75.4 in.)

Min. ground clearance

405 mm (15.9 in.)

Tread

Front

1340 mm (52.8 in.)

Rear

1325 mm (52.2 in.), 1430 mm (56.3 in.)

Weight (with ROPS or CABIN)

1680 kg (3705 lbs)

1700 kg (3750 lbs)

1855 kg (4090 lbs)

Standard

Front

9.5-16

tire size

Rear

14.9-26

Clutch

Dry type single stage

Travelling

Steering

Hydrostatic power steering

system

Transmission

F12, R8 Glide shift

Hydrotstatic transmission (3 speeds)

transmission

Braking system

Wet disk type

Min. turning radius

2.8 m (9.2 feet)

(with brake)

Hydraulic control system

Position control

Pump capacity

37.0 L (9.8 U.S.gals., 8.1 Imp.gals.) / min.

Hydraulic

Three point hitch

SAE Category I

system

Max. lift

At lift points

1750 kg (3860 lbs)

24 in. behind

force

1350 kg (2980 lbs)

lift points

System pressure

18.1 to 19.1 MPa (185 to 195 kgf/cm2, 2633 to 2775 psi)

Rear PTO

SAE 1-3/8, 6 splines

PTO / Engine speed

540 min−1 (rpm) /

540 min

−1

(rpm) / 2660 min

−1

(rpm)

PTO

2550 min−1 (rpm)

Mid-PTO (if equipped)

USA No. 5 (KUBOTA 10-tooth) involute spline

PTO / Engine speed

2000 min−1 (rpm) /

2000 min

−1

(rpm) / 2690 min

−1

(rpm)

2580 min−1 (rpm)

Note : * Manufacture’s estimate

The company reserves the right to change the specifications without notice.

W10417330

KiSC issued 06, 2006 A

13

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM TRAVELLING SPEEDS

TRAVELLING SPEEDS

[Manual Transmission Type]

		Model		L3130		L3830		L4330		L4630		L5030
				L3430
Tire size (Rear)				12.4-24		14.9-24		14.9-24		14.9-24		14.9-26
Shuttle shift		Range	Main gear
lever		gear shift	shift lever	km/h (mph)		km/h (mph)		km/h (mph)		km/h (mph)		km/h (mph)
		lever
			1	1.6	(1.0)	1.5	(0.9)	1.6	(1.0)	1.5	(0.9)	1.5	(0.9)
		Low	2	2.3	(1.4)	2.1	(1.3)	2.2	(1.4)	2.1	(1.3)	2.2	(1.4)
			3	3.7	(2.3)	3.5	(2.2)	3.6	(2.2)	3.5	(2.2)	3.5	(2.2)
Forward
			4	5.4	(3.4)	5.1	(3.2)	5.3	(3.3)	5.1	(3.2)	5.2	(3.2)
(At rated
			1	7.8	(4.8)	7.6	(4.7)	7.7	(4.8)	7.6	(4.7)	7.8	(4.8)
engine rpm)
		High	2	11.1 (6.9)		10.7 (6.6)		10.9 (6.8)		10.7 (6.6)		11.0 (6.8)
			3	18.0 (11.2)		17.4	(10.8)	17.6	(10.8)	17.4	(10.8)	17.9	(10.9)
			4	26.6	(16.5)	25.7	(16.0)	26.0	(16.2)	25.7	(16.0)	26.4	(16.4)
			1	1.5	(0.9)	1.4	(0.9)	1.5	(0.9)	1.4	(0.9)	1.5	(0.9)
		Low	2	2.2	(1.4)	2.0	(1.2)	2.1	(1.3)	2.0	(1.2)	2.1	(1.3)
			3	3.5	(2.2)	3.3	(2.1)	3.4	(2.1)	3.3	(2.1)	3.4	(2.1)
Reverse
			4	5.2	(3.2)	4.9	(3.0)	5.1	(3.2)	4.9	(3.0)	5.0	(3.1)
(At rated
			1	7.5	(4.7)	7.2	(4.5)	7.3	(4.5)	7.2	(4.5)	7.4	(4.6)
engine rpm)
		High	2	10.6 (6.6)		10.2 (6.3)		10.4 (6.5)		10.2 (6.3)		10.4 (6.5)
			3	17.2	(10.7)	16.6	(10.3)	16.8	(10.4)	16.6	(10.3)	17.1	(10.6)
			4	25.4	(15.8)	24.5	(15.2)	24.8	(15.4)	24.5	(15.2)	25.2	(15.7)

The company reserves the right to change the specifications without notice.

W1035065

KiSC issued 06, 2006 A

14

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM										TRAVELLING SPEEDS
[GST Type]
	Model		L3130		L3830		L4330		L4630		L5030
			L3430
Tire size (Rear)			12.4-24		14.9-24		14.9-24		14.9-24		14.9-26
Shuttle shift		Main gear shift	km/h (mph)		km/h (mph)		km/h (mph)		km/h (mph)		km/h (mph)
lever		lever
		1	1.6	(1.0)	1.5	(0.9)	1.6	(1.0)	1.5	(0.9)	1.5	(0.9)
		2	2.3	(1.4)	2.1	(1.3)	2.2	(1.4)	2.1	(1.3)	2.2	(1.4)
		3	3.1	(1.9)	2.9	(1.8)	3.0	(1.9)	2.9	(1.8)	2.9	(1.8)
		4	3.7	(2.3)	3.5	(2.2)	3.6	(2.2)	3.5	(2.2)	3.5	(2.2)
		5	4.5	(2.8)	4.2	(2.6)	4.4	(2.7)	4.2	(2.6)	4.3	(2.7)
Forward
		6	5.4	(3.4)	5.1	(3.2)	5.3	(3.3)	5.1	(3.2)	5.2	(3.2)
(At rated
		7	6.5	(4.0)	6.3	(3.9)	6.4	(4.0)	6.3	(3.9)	6.5	(4.0)
engine rpm)
		8	7.8	(4.8)	7.6	(4.7)	7.7	(4.8)	7.6	(4.7)	7.8	(4.8)
		9	9.2	(5.7)	8.9	(5.5)	9.0	(5.6)	8.9	(5.5)	9.1	(5.7)
		10	11.1 (6.9)		10.7 (6.6)		10.9 (6.8)		10.7 (6.6)		11.0 (6.8)
		11	18.0 (11.2)		17.4	(10.8)	17.6	(10.8)	17.4	(10.8)	17.9	(10.9)
		12	26.6	(16.5)	25.7	(16.0)	26.0	(16.2)	25.7	(16.0)	26.4	(16.4)
		1	1.5	(0.9)	1.4	(0.9)	1.5	(0.9)	1.4	(0.9)	1.5	(0.9)
		2	2.2	(1.4)	2.0	(1.2)	2.1	(1.3)	2.0	(1.2)	2.1	(1.3)
		3	3.5	(2.2)	3.3	(2.1)	3.4	(2.1)	3.3	(2.1)	3.4	(2.1)
Reverse
		4	5.2	(3.2)	4.9	(3.0)	5.1	(3.2)	4.9	(3.0)	5.0	(3.1)
(At rated
		5	7.5	(4.7)	7.2	(4.5)	7.3	(4.5)	7.2	(4.5)	7.4	(4.6)
engine rpm)
		6	10.6 (6.6)		10.2 (6.3)		10.4 (6.5)		10.2 (6.3)		10.4 (6.5)
		7	17.2	(10.7)	16.6	(10.3)	16.8	(10.4)	16.6	(10.3)	17.1	(10.6)
		8	25.4	(15.8)	24.5	(15.2)	24.8	(15.4)	24.5	(15.2)	25.2	(15.7)
The company reserves the right to change the specifications without notice.
												W1032246

KiSC issued 06, 2006 A

15

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM						TRAVELLING SPEEDS
[With Creep Speed Model]
	Model				L4630 CABIN
Creep gear shift lever			High			Low
Tire size (Rear)					14.9-24
Shuttle shift lever		Main gear shift lever	km/h (mph)			km/h (mph)
		1	1.5	(0.9)		0.17 (0.11)
		2	2.1	(1.3)		0.24 (0.15)
		3	2.9	(1.8)		0.32 (0.20)
		4	3.5	(2.2)		0.39 (0.24)
		5	4.2	(2.6)		0.47 (0.29)
Forward		6	5.1	(3.2)		0.57 (0.35)
(At rated engine rpm)		7	6.3	(3.9)		0.71 (0.44)
		8	7.6	(4.8)		0.85 (0.53)
		9	8.9	(5.5)		1.00 (0.62)
		10	10.7 (6.6)			1.20 (0.75)
		11	17.4	(10.8)		1.95 (1.21)
		12	25.7	(16.0)		2.88 (1.79)
		1	1.4	(0.9)		0.16 (0.10)
		2	2.0	(1.2)		0.23 (0.14)
		3	3.3	(2.1)		0.37 (0.23)
Reverse		4	4.9	(3.0)		0.55 (0.34)
(At rated engine rpm)		5	7.2	(4.5)		0.81 (0.50)
		6	10.2 (6.2)			1.15 (0.71)
		7	16.6	(10.3)		1.86 (1.16)
		8	24.5	(15.2)		2.75 (1.71)
The company reserves the right to change the specifications without notice.
						W1033852

KiSC issued 06, 2006 A

16

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM					TRAVELLING SPEEDS
[HST Type]
Model		L3130	L3830	L4330	L4630	L5030
		L3430
Tire size (Rear)		12.4-24	14.9-24	14.9-24	14.9-24	14.9-26
Shuttle shift	Range gear	km/h (mph)	km/h (mph)	km/h (mph)	km/h (mph)	km/h (mph)
lever	shift lever
	L	0 to 6.3	0 to 5.9	0 to 6.2	0 to 5.9	0 to 6.1
		(0 to 3.9)	(0 to 3.7)	(0 to 3.9)	(0 to 3.7)	(0 to 3.8)
Forward
		0 to 12.1	0 to 11.4	0 to 11.9	0 to 11.4	0 to 11.8
(At rated	M
		(0 to 7.5)	(0 to 7.1)	(0 to 7.4)	(0 to 7.1)	(0 to 7.3)
engine rpm)
	H	0 to 27.0	0 to 25.3	0 to 26.4	0 to 25.3	0 to 26.1
		(0 to 16.8)	(0 to 15.7)	(0 to 16.4)	(0 to 15.7)	(0 to 16.2)
	L	0 to 5.7	0 to 5.3	0 to 5.5	0 to 5.3	0 to 5.5
		(0 to 3.5)	(0 to 3.3)	(0 to 3.4)	(0 to 3.3)	(0 to 3.4)
Reverse
		0 to 10.9	0 to 10.3	0 to 10.7	0 to 10.3	0 to 10.6
(At rated	M
		(0 to 6.8)	(0 to 6.4)	(0 to 6.6)	(0 to 6.4)	(0 to 6.6)
engine rpm)
	H	0 to 24.3	0 to 22.8	0 to 23.8	0 to 22.8	0 to 23.5
		(0 to 15.1)	(0 to 14.2)	(0 to 14.8)	(0 to 14.2)	(0 to 14.6)

The company reserves the right to change the specifications without notice.

W1034865

KiSC issued 06, 2006 A

17

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM	DIMENSIONS

DIMENSIONS

[L3130, L3430, L3830]

KiSC issued 06, 2006 A

18

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

DIMENSIONS

[L4330, L4630, L5030]

KiSC issued 06, 2006 A

19

G GENERAL

KiSC issued 06, 2006 A

GENERAL

CONTENTS

1.	TRACTOR IDENTIFICATION .........................................................................	G-1
	[1] MODEL NAME AND SERIAL NUMBERS..............................................	G-1
	[2] E2 ENGINE ...............................................................................................	G-3
	[3] CYLINDER NUMBER ...............................................................................	G-3
2.	GENERAL PRECAUTIONS ............................................................................	G-4
3.	HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING ..	G-5
	[1] WIRING .....................................................................................................	G-5
	[2] BATTERY...................................................................................................	G-7
	[3] FUSE..........................................................................................................	G-7
	[4] CONNECTOR ............................................................................................	G-7
	[5] HANDLING OF CIRCUIT TESTER.........................................................	G-8
4.	LUBRICANTS, FUEL AND COOLANT .........................................................	G-9
5.	TIGHTENING TORQUES .............................................................................	G-11
	[1] GENERAL USE SCREWS, BOLTS AND NUTS.................................	G-11
6.	MAINTENANCE .............................................................................................	G-12
7.	CHECK AND MAINTENANCE.....................................................................	G-14
	[1] DAILY CHECK ........................................................................................	G-14
	[2] CHECK POINTS OF INITIAL 50 HOURS...........................................	G-15
	[3] CHECK POINTS OF EVERY 50 HOURS...........................................	G-19
	[4] CHECK POINTS OF EVERY 100 HOURS ........................................	G-22
	[5] CHECK POINTS OF EVERY 200 HOURS .........................................	G-27
	[6] CHECK POINTS OF EVERY 400 HOURS .........................................	G-32
	[7] CHECK POINTS OF EVERY 600 HOURS .........................................	G-32
	[8] CHECK POINTS OF EVERY 800 HOURS .........................................	G-32
	[9] CHECK POINTS OF EVERY 1500 HOURS .......................................	G-32
	[10]CHECK POINTS OF EVERY 3000 HOURS .......................................	G-32
	[11]CHECK POINTS OF EVERY 1 YEAR ................................................	G-33
	[12]CHECK POINTS OF EVERY 2 YEARS..............................................	G-33
	[13]OTHERS ..................................................................................................	G-35
8.	SPECIAL TOOLS..........................................................................................	G-39
	[1] SPECIAL TOOLS FOR ENGINE ..........................................................	G-39
	[2] SPECIAL TOOLS FOR TRACTOR.......................................................	G-47
9.	TIRES.............................................................................................................	G-55
	[1] TIRE PRESSURE ...................................................................................	G-55
	[2] TREADS ADJUSTMENT ........................................................................	G-56
	(1) Front Wheels......................................................................................	G-56
	(2) Rear Wheels ......................................................................................	G-57
	[3] TIRE LIQUID INJECTION ......................................................................	G-59
	[4] IMPLEMENT LIMITATIONS....................................................................	G-62

KiSC issued 06, 2006 A

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

G GENERAL

1. TRACTOR IDENTIFICATION

[1] MODEL NAME AND SERIAL NUMBERS

When contacting your local KUBOTA distributor, always specify engine serial number, tractor serial number and hour meter reading.

(1)	Tractor Identification Plate	(4)	Engine Serial Number
(2)	CABIN Identification Plate	(5)	Hour Meter (IntelliPanel Display)
	(CABIN Serial Number)
(3)	Tractor Serial Number

W10106000

KiSC issued 06, 2006 A

G-1

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM											G GENERAL
		Engine Serial Number
			When contacting the manufacture, always specify your engine
		model name and serial number.
			The engine model and its serial number need to be identified
		before the engine can be serviced or parts replaced.
		■ Engine Serial Number
			The engine serial number is an identified number for the engine.
		It is marked after the engine model number.
			It indicates month and year of manufacture as follows.
		•	Year of manufacture
			Alphabet or		Year		Alphabet or				Year
			Number				Number
			1	2001			F				2015
			2	2002			G				2016
			3	2003			H				2017
			4	2004			J				2018
			5	2005			K				2019
			6	2006			L				2020
			7	2007			M				2021
			8	2008			N				2022
			9	2009			P				2023
			A	2010			R				2024
			B	2011			S				2025
			C	2012			T				2026
			D	2013			V				2027
			E	2014
		•	Month of manufacture
		Month			Engine Serial Number
					0001 ~ 9999				10000 ~
		January			A0001 ~ A9999				B0001 ~
		February			C0001 ~ C9999				D0001 ~
		March			E0001 ~ E9999				F0001 ~
		April			G0001 ~ G9999				H0001 ~
		May			J0001 ~ J9999				K0001 ~
		June			L0001 ~ L9999				M0001 ~
		July			N0001 ~ N9999				P0001 ~
		August			Q0001 ~ Q9999				R0001 ~
		September			S0001 ~ S9999				T0001 ~
		October			U0001 ~ U9999				V0001 ~
		November			W0001 ~ W9999				X0001 ~
		December			Y0001 ~ Y9999				Z0001 ~

e.g. D1803-3A0001

“3” indicates 2003 and “A” indicates January.

So, 3A indicates that the engine was manufactured on January, 2003.

(1) Engine Model and Serial Number

W1010477

KiSC issued 06, 2006 A

G-2

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

G GENERAL

[2] E2 ENGINE

[ex.: Model Name D1803-M-E2-XXXX]

The emission controls that have been put into effect in various countries to prevent air pollution will be stepped up. The time to enforce the regulations differs depending on the engine output classifications.

Kubota has been supplying the diesel engines conforming to the emission regulations in respective countries. Exhaust emissions regulations shift to the second stage. Kubota executed the improvement of the engine according to this regulation.

In order to discriminate the engines conforming to Tier 1 / Phase 1 requirements and those conforming to Tier 2 / Phase 2 requirements, we have adopted E2 as a new model name for the engines conforming Tier 2 / Phase 2 regulations with emission label (1) or (2).

In the after-sale services for 03-M-E2 series engines, only use the dedicated parts for E2 models and carry out the maintenance services accordingly.

[3] CYLINDER NUMBER

The cylinder numbers of KUBOTA diesel engine are designated as shown in the figure.

The sequence of cylinder numbers is given as No.1, No.2, No.3 and No.4 starting from the gear case side.

W1011077

KiSC issued 06, 2006 A

G-3

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

G GENERAL

2.GENERAL PRECAUTIONS

•During disassembly, carefully arrange removed parts in a clean area to prevent confusion later. Screws, bolts and nuts should be installed in their original position to prevent reassembly errors.

•When special tools are required, use KUBOTA genuine special tools. Special tools which are not frequently used should be made according to the drawings provided.

•Before disassembling or servicing electrical wires, always disconnect the ground cable from the battery first.

•Remove oil and dirt from parts before measuring.

•Use only KUBOTA genuine parts for parts replacement to maintain machine performance and to assure safety.

•Gaskets and O-rings must be replaced during reassembly. Apply grease to new O-rings or oil seals before assembling. See the figure left side.

•When reassembling external snap rings or internal snap rings, they must be positioned so that sharp edge faces against the direction from which a force is applied. See the figure left side.

•When inserting spring pins, their splits must face the direction from which a force is applied. See the figure left side.

•To prevent damage to the hydraulic system, use only specified fluid or equivalent.

(1)	Grease	(A) External Snap Ring
(2)	Force	(B) Internal Snap Ring

(3)Sharp Edge

(4)Axial Force

(5)Rotating Movement

W10109040

KiSC issued 06, 2006 A

G-4

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

G GENERAL

3.HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING

[1] WIRING

To ensure safety and prevent damage to the machine and surrounding equipment, heed the following precautions in handling electrical parts and wiring.

■ IMPORTANT

•Check electrical wiring for damage and loosened connection every year. To this end, educate the customer to do his or her own check and at the same time recommend the dealer to perform periodic check for a fee.

•Do not attempt to modify or remodel any electrical parts and wiring.

•When removing the battery cables, disconnect the negative cable first. When installing the battery cables, connect the positive cable first.

(1) Negative Terminal

(2) Positive Terminal

W10111140

• Securely tighten wiring terminals.

(1) Correct	(2) Incorrect
(Securely Tighten)	(Loosening Leads to Faulty Contact)
	W10112160

• Do not let wiring contact dangerous part.

(1)	Wiring (Correct)	(3)	Dangerous Part
(2)	Wiring (Incorrect)	(4)	Dangerous Part

W10113130

• Securely insert grommet.

(1) Grommet	(A) Correct
	(B) Incorrect

W10113880

KiSC issued 06, 2006 A

G-5

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

G GENERAL

• Securely clamp, being careful not to damage wiring.

(1)	Clamp	(3)	Clamp
	• Wind Clamp Spirally	(4)	Welding Dent
(2)	Wire Harness

W10114580

•Clamp wiring so that there is no twist, unnecessary sag, or excessive tension, except for movable part, where sag be required.

(1)	Wiring	(A) Correct
(2)	Clamp	(B) Incorrect

W10115870

• In installing a part, take care not to get wiring caught by it.

(1) Wiring

(A) Incorrect

W10116700

•After installing wiring, check protection of terminals and clamped condition of wiring, only connect battery.

(1)Cover

• Securely Install Cover

W10117350

KiSC issued 06, 2006 A

G-6

L3130 · L3430 · L3830 · L4330 · L4630 · L5030, WSM

G GENERAL

[2] BATTERY

[3] FUSE

[4] CONNECTOR

•Take care not to confuse positive and negative terminal posts.

•When removing battery cables, disconnect negative cable first. When installing battery cables, check for polarity and connect positive cable first.

•Do not install any battery with capacity other than is specified (Ah).

•After connecting cables to battery terminal posts, apply high temperature grease to them and securely install terminal covers on them.

•Do not allow dirt and dust to collect on battery.

CAUTION

•Take care not to let battery liquid spill on your skin and clothes. If contaminated, wash it off with water immediately.

•Before recharging the battery, remove it from the machine.

•Before recharging, remove cell caps.

•Do recharging in a well-ventilated place where there is no open flame nearby, as hydrogen gas and oxygen are formed.

W10118160

•Use fuses with specified capacity.

Neither too large or small capacity fuse is acceptable.

•Never use steel or copper wire in place of fuse.

•Do not install working light, radio set, etc. on machine which is not provided with reserve power supply.

•Do not install accessories if fuse capacity of reserve power supply is exceeded.

(1) Fuse

(2) Slow Blow Fuse

W10120920

• For connector with lock, push lock to separate.

(A) Push

W10122110

•In separating connectors, do not pull wire harnesses.

•Hold connector bodies to separate.

(A) Correct

(B) Incorrect

W10122720

KiSC issued 06, 2006 A

G-7