KROHNE IFC 070 Operating Manual

Handbook

IFC 070

IFC 070IFC 070

HandbookHandbook

Electromagnetic signal converter

Electronic Revision ER 4.0.0_

The documentation is only complete when used in combination with the relevant documentation for the sensor.

: IMPRINT ::::::::::::::::::::::::::::::::::

Subject to change without notice.

www.krohne.com 11/2009 - 7311242200 - MA IFC 070 R02

IFC 070

CONTENTS

1 Safety instructions 5

1.1 Software versions............................................................................................................. 5

1.2 Intended use ..................................................................................................................... 5

1.3 Transportation, handling and using instruction for batteries ......................................... 6

1.4 Safety instructions from the manufacturer ..................................................................... 6

1.4.1 Copyright and data protection ................................................................................................ 6

1.4.2 Disclaimer ............................................................................................................................... 7

1.4.3 Product liability and warranty ................................................................................................ 8

1.4.4 Information concerning the documentation........................................................................... 8

1.4.5 Warnings and symbols used................................................................................................... 9

1.5 Safety instructions for the operator................................................................................. 9

2 Device description 10

2.1 Instrument description................................................................................................... 10

2.2 Scope of delivery............................................................................................................. 10

2.3 Nameplate ...................................................................................................................... 11

3 Installation 12

3.1 Notes on installation ......................................................................................................12

3.2 Storage ........................................................................................................................... 12

3.3 Transport ........................................................................................................................ 12

3.4 Pre-installation requirements ....................................................................................... 12

3.5 Installation requirements .............................................................................................. 13

3.5.1 Vibration ................................................................................................................................ 13

3.5.2 Magnetic field........................................................................................................................ 13

3.5.3 Installation of converter........................................................................................................ 13

4 Electrical connections 14

4.1 Safety instructions.......................................................................................................... 14

4.2 Grounding ....................................................................................................................... 14

4.3 Signal cable .................................................................................................................... 14

4.4 Connection of signal cable ............................................................................................. 15

4.5 Terminal assignment of converter................................................................................. 16

5 Start-up 17

5.1 Connection of battery ..................................................................................................... 17

5.1.1 Internal battery ..................................................................................................................... 17

5.1.2 External battery .................................................................................................................... 17

6 Operation 19

6.1 Display and operating elements .................................................................................... 19

6.2 Menu of converter ..........................................................................................................19

www.krohne.com11/2009 - 7311242200 - MA IFC 070 R02

CONTENTS

IFC 070

7 Service 24

7.1 Replacement of battery .................................................................................................. 24

7.1.1 Replacement of internal battery........................................................................................... 24

7.1.2 Replacement of external battery..........................................................................................25

7.2 Spare parts availability...................................................................................................26

7.3 Availability of services .................................................................................................... 26

7.4 Returning the device to the manufacturer..................................................................... 26

7.4.1 General information.............................................................................................................. 26

7.4.2 Form (for copying) to accompany a returned device............................................................ 28

7.5 Disposal .......................................................................................................................... 28

8 Technical data 29

8.1 Measuring principle........................................................................................................29

8.2 Technical data................................................................................................................. 30

8.3 Measuring accuracy ....................................................................................................... 33

8.4 Dimensions and weights ................................................................................................ 33

9 Notes 34

www.krohne.com 11/2009 - 7311242200 - MA IFC 070 R02

IFC 070

1.1 Software versions

For all GDC devices, the "Electronic Revision" (ER) is consulted to document the revision status of the electronics according to NE 53. It is easy to see from the ER whether any fault repairs or major changes to the electronic equipment have taken place and what effect they have had on compatibility.

Changes and effect on compatibility

1 Downwards compatible changes and fault repair with no effect on operation (e.g. spelling

mistakes on display)

3-_ Downwards compatible hardware and/or software change of inputs and outputs:

P Pulse output

S Status output

X all inputs and outputs

4 Downwards compatible changes with new functions

5 Incompatible changes, i.e. electronic equipment must be changed.

SAFETY INSTRUCTIONS 1

Release date Electronic revision Changes and

2009 ER2.3.1_

2009 ER4.0.0_

CAUTION!

The OPTIFLUX 2070 and the WATERFLUX 3070 are different instruments with different software. The difference lies in the Electronic Revision number, which can be found on a sticker on the IFC 070 electronics. The electronics are therefore not compatible with each other!

1.2 Intended use

This signal converter IFC 070 has been designed to be combined with a WATERFLUX 3000 water meter or with an OPTIFLUX 2000 flow sensor, for measuring potable water and water with suspended particles.

This device features not only accurate flow measurement, but also continuous diagnostics in accordance with applicable standards. This self-diagnosis monitors and automatically reports improper functioning of the electronics, or faulty sensor electrodes. It reports battery charge condition and even provides a cable-break alarm.

Documentation

compatibility

Initial software version MA IFC 070 R01

(SW. REV. 2.3.1_)

1; 3-P; 3-S; 4 MA IFC 070 R02

(SW. REV. 4.0.4_)

www.krohne.com11/2009 - 7311242200 - MA IFC 070 R02

1 SAFETY INSTRUCTIONS

1.3 Transportation, handling and using instruction for batteries

WARNING!

The used lithium batteries are primary power sources with high energy content. If mistreated, they may present a potential risk.

INFORMATION!

The manufacturer assumes no liability for customer failure.

Please observe the following transportation, handling and using instructions:

• Transport only in special packaging with special labels and transportation documents.

• Do not short-circuit, recharge, overcharge or connect with false polarity.

• Do not expose to temperature beyond the specified temperature range or incinerate the

battery.

• Do not crush, puncture or open cells or disassemble battery packs.

• Do not weld or solder to the body of the battery.

• Do not expose contents of battery to water.

• Remove the battery from device before returning to the manufacturer for service or warranty

reasons.

• Dispose battery packs in accordance with local regulations; where possible, recycle used batteries.

IFC 070

1.4 Safety instructions from the manufacturer

1.4.1 Copyright and data protection

The contents of this document have been created with great care. Nevertheless, we provide no guarantee that the contents are correct, complete or up-to-date.

The contents and works in this document are subject to German copyright. Contributions from third parties are identified as such. Reproduction, processing, dissemination and any type of use beyond what is permitted under copyright requires written authorisation from the respective author and/or the manufacturer.

The manufacturer tries always to observe the copyrights of others, and to draw on works created in-house or works in the public domain.

The collection of personal data (such as names, street addresses or e-mail addresses) in the manufacturer's documents is always on a voluntary basis whenever possible. Whenever feasible, it is always possible to make use of the offerings and services without providing any personal data.

We draw your attention to the fact that data transmission over the Internet (e.g. when communicating by e-mail) may involve gaps in security. It is not possible to protect such data completely against access by third parties.

We hereby expressly prohibit the use of the contact data published as part of our duty to publish an imprint for the purpose of sending us any advertising or informational materials that we have not expressly requested.

www.krohne.com 11/2009 - 7311242200 - MA IFC 070 R02

IFC 070

1.4.2 Disclaimer

The manufacturer will not be liable for any damage of any kind by using its product, including, but not limited to direct, indirect, incidental, punitive and consequential damages.

This disclaimer does not apply in case the manufacturer has acted on purpose or with gross negligence. In the event any applicable law does not allow such limitations on implied warranties or the exclusion of limitation of certain damages, you may, if such law applies to you, not be subject to some or all of the above disclaimer, exclusions or limitations.

Any product purchased from the manufacturer is warranted in accordance with the relevant product documentation and our Terms and Conditions of Sale.

The manufacturer reserves the right to alter the content of its documents, including this disclaimer in any way, at any time, for any reason, without prior notification, and will not be liable in any way for possible consequences of such changes.

SAFETY INSTRUCTIONS 1

www.krohne.com11/2009 - 7311242200 - MA IFC 070 R02

1 SAFETY INSTRUCTIONS

1.4.3 Product liability and warranty

The operator shall bear responsibility for the suitability of the device for the specific purpose. The manufacturer accepts no liability for the consequences of misuse by the operator. Improper installation and operation of the devices (systems) will cause the warranty to be void. The respective "Standard Terms and Conditions" which form the basis for the sales contract shall also apply.

1.4.4 Information concerning the documentation

To prevent any injury to the user or damage to the device it is essential that you read the information in this document and observe applicable national standards, safety requirements and accident prevention regulations.

If this document is not in your native language and if you have any problems understanding the text, we advise you to contact your local office for assistance. The manufacturer can not accept responsibility for any damage or injury caused by misunderstanding of the information in this document.

This document is provided to help you establish operating conditions, which will permit safe and efficient use of this device. Special considerations and precautions are also described in the document, which appear in the form of underneath icons.

IFC 070

www.krohne.com 11/2009 - 7311242200 - MA IFC 070 R02

IFC 070

1.4.5 Warnings and symbols used

Safety warnings are indicated by the following symbols.

DANGER!

This information refers to the immediate danger when working with electricity.

DANGER!

This warning refers to the immediate danger of burns caused by heat or hot surfaces.

DANGER!

These warnings must be observed without fail. Even partial disregard of this warning can lead to serious health problems and even death. There is also the risk of seriously damaging the device or parts of the operator's plant.

WARNING!

Disregarding this safety warning, even if only in part, poses the risk of serious health problems. There is also the risk of damaging the device or parts of the operator's plant.

SAFETY INSTRUCTIONS 1

CAUTION!

Disregarding these instructions can result in damage to the device or to parts of the operator's plant.

INFORMATION!

These instructions contain important information for the handling of the device.

LEGAL NOTICE!

This note contains information on statutory directives and standards.

• HANDLING

HANDLING

HANDLINGHANDLING

This symbol designates all instructions for actions to be carried out by the operator in the specified sequence.

i RESULT

RESULT

RESULTRESULT This symbol refers to all important consequences of the previous actions.

1.5 Safety instructions for the operator

WARNING!

In general, devices from the manufacturer may only be installed, commissioned, operated and maintained by properly trained and authorized personnel. This document is provided to help you establish operating conditions, which will permit safe and efficient use of this device.

www.krohne.com11/2009 - 7311242200 - MA IFC 070 R02

2 DEVICE DESCRIPTION

2.1 Instrument description

Two versions are available. You received a compact version or a remote version.

Figure 2-1: Versions

1 compact version 2 remote version

IFC 070

2.2 Scope of delivery

Figure 2-2: Scope of delivery

1 Ordered flowmeter 2 Quick Start 3 Factory calibration report 4 CD-ROM with product documentation 5 Cable (remote versions only)

www.krohne.com 11/2009 - 7311242200 - MA IFC 070 R02

IFC 070

2.3 Nameplate

INFORMATION!

Look at the device nameplate to ensure that the device is delivered according to your order. Check for the correct supply voltage printed on the nameplate.

DEVICE DESCRIPTION 2

Figure 2-3: Example for nameplate

1 Manufacturer 2 Voltage information 3 Electronic Revision number 4 Material of wetted parts 5 Meter constant 6 Serial number 7 Device type

www.krohne.com11/2009 - 7311242200 - MA IFC 070 R02

+ 25 hidden pages