KSM3311X
W10747071B_EN_v01.indd 1 |
|
|
2/29/16 2:15 PM |
|
|
PARTS AND FEATURES
PARTS AND ACCESSORIES
Motor head
Speed control
Wire whip
Dough hook
2 | PARTS AND FEATURES
Attachment hub
Beater shaft
Flat
beater
Bowl
Flex Edge beater*
Pouring shield*
*Accessory sold separately
W10747071B_EN_v01.indd 2 |
|
|
2/29/16 2:15 PM |
|
|
STAND MIXER SAFETY
ENGLISH |
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, including the following:
1.Read all instructions.
2.To avoid risk of electrical shock, do not put Stand Mixer in water or other liquid.
3.Close supervision is necessary when any appliance is used by or near children.
4.Unplug the Stand Mixer from outlet when not in use, before putting on or taking off parts, and before cleaning.
5.Avoid contacting moving parts. Keep hands, hair, and clothing, as well
as spatulas and other utensils, away from beater during operation to reduce the risk of injury to persons and/or damage to the Stand Mixer.
6.Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest Authorized Service Facility for examination, repair or adjustment.
7.The use of accessories not recommended or sold by KitchenAid may cause fire, electric shock or injury.
8.Do not use the Stand Mixer outdoors.
9.Do not let the cord hang over the edge of table or counter.
STAND MIXER SAFETY | 3
W10747071B_EN_v01.indd 3 |
|
|
2/29/16 2:15 PM |
|
|
STAND MIXER SAFETY
10.Do not let the cord contact hot surfaces, including the stove.
11.Remove the flat beater, wire whip, or spiral dough hook from the Stand Mixer before washing.
SAVE THESE INSTRUCTIONS
THIS PRODUCT IS DESIGNED FOR HOUSEHOLD USE ONLY.
ELECTRICAL REQUIREMENTS
Voltage: 120 V Frequency: 60 Hz Wattage: 250 Watts
NOTE: The power rating for your Stand Mixer is printed on the serial plate.
Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.
The maximum rating is based on the attachment that draws the greatest load (power). Other recommended attachments may draw significantly less power.
USING THE STAND MIXER
CHOOSING THE RIGHT ACCESSORY
ACCESSORY |
USE TO MIX |
DESCRIPTION |
FLAT BEATER |
Normal |
Cakes, Creamed frostings, Candies, |
FLEX EDGE BEATER* |
to heavy |
Cookies, Biscuits, Pie pastry, Meat loaf, |
|
mixtures |
Mashed potatoes |
WIRE WHIP |
Mixtures |
Eggs, Egg whites, Heavy cream, |
|
that need air |
Boiled frostings, Sponge cakes, |
|
incorporated |
Mayonnaise, some Candies |
DOUGH HOOK |
Mixing and |
Breads, Rolls, Pizza dough, Buns |
|
kneading yeast |
|
|
doughs |
|
4 | USING THE STAND MIXER |
*Accessory sold separately |
|
|
W10747071B_EN_v01.indd 4 |
|
|
2/29/16 2:15 PM |
|
|
USING THE STAND MIXER
SPEED CONTROL GUIDE
All speeds have the Soft Start® feature which automatically starts the Stand Mixer at a lower speed to help avoid ingredient splash-out and “flour puff” at start-up, then quickly increases to the selected speed for optimal performance.
NOTE: The speed control can be set between the speeds listed in the chart to obtain speeds 1, 3, 5, 7, and 9 if a finer adjustment is required. Do not exceed Speed 2 when preparing yeast doughs as this may cause damage to the Stand Mixer.
SPEED ACCESSORY |
ACTION |
DESCRIPTION |
STIR |
STIR |
For starting all mixing procedures, slow |
|
|
stirring, combining, and mashing. Use to |
|
|
add flour and dry ingredients to batter, |
1 |
|
and to add liquids to dry ingredients. |
|
Do not use Speed 1 to mix or knead |
|
|
|
|
|
|
yeast doughs. |
2 |
SLOW MIXING |
For slow mixing, mashing, and faster |
|
|
stirring. Use to mix and knead yeast |
|
|
doughs, heavy batters, and candies; |
|
|
start mashing potatoes or other |
|
|
vegetables; cut shortening into flour; |
|
|
mix thin or splashy batters. |
4 |
MIXING, |
For mixing semi-heavy batters, such |
|
BEATING |
as cookies. Use to combine sugar and |
|
|
shortening, and to add sugar to egg |
|
|
whites for meringues. Medium speed |
|
|
for cake mixes. |
6 |
BEATING, |
For medium-fast beating (creaming), |
|
CREAMING |
or whipping. Use to finish mixing cake, |
|
|
doughnut, and other batters. High |
|
|
speed for cake mixes. |
8 |
FAST BEATING, |
For whipping cream, egg whites, |
|
WHIPPING |
and boiled frostings. |
10 |
FAST WHIPPING |
For whipping small amounts of cream, |
|
|
or egg whites; for final whipping of |
|
|
mashed potatoes. |
ENGLISH
NOTE: To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.
FOR DETAILED INFORMATION ON USING THE STAND MIXER:
Visit kitchenaid.com/quickstart for additional Instructions with videos, inspiring recipes, and tips on how to use your Stand Mixer.
USING THE STAND MIXER | 5
W10747071B_EN_v01.indd 5 |
|
|
2/29/16 2:15 PM |
|
|
USING THE STAND MIXER
ASSEMBLING THE STAND MIXER
Check to be sure that the Stand
1 Mixer is unplugged, and the speed control is turned to “0”.
NOTE: To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.
Raise the motor head: Slide the locking lever to the unlock position
2 and lift the motor head. Once lifted, slide the locking lever to the lock position to keep the motor head up.
Attach the bowl: Place the bowl on
3 the bowl clamping plate and gently turn it in a clockwise direction to lock it into place.
Attach any accessory: Slip the accessory onto the beater shaft and
4 press upward as far as possible. Turn the accessory counterclockwise to hook the accessory over the pin on the shaft.
6 | USING THE STAND MIXER
W10747071B_EN_v01.indd 6 |
|
|
2/29/16 2:15 PM |
|
|
USING THE STAND MIXER
ASSEMBLING THE STAND MIXER
Lower the motor head: Slide the locking lever to the unlock position and guide the motor head down.
5 Make sure motor head is completely down, then slide the locking lever to the lock position. Before mixing, test lock by attempting to raise motor head.
(OPTIONAL) To adjust beater to bowl clearance: Tilt the motor head back; then turn the screw slightly counterclockwise (left) to raise the beater, or clockwise (right) to lower the beater. Adjust the beater so that it just clears the surface of the bowl. If you over adjust the screw, the bowl lock lever may not lock into place.
(OPTIONAL) Place the pouring shield*:
Slide the pouring shield* from the front of the Stand Mixer over the bowl until the pouring shield* is centered. The bottom rim of the pouring shield* fits inside of the bowl. The pouring chute will be just to the
right of the attachment hub as you face the Stand Mixer.
IMPORTANT: Your Stand Mixer is adjusted at the factory so that the flat beater just clears the bottom of the bowl. If, for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, you can easily correct the clearance.
NOTE: When properly adjusted, the flat beater will not strike on the bottom or sides of the bowl. If the flat beater or the wire whip is so close that it strikes the bottom of the bowl, coating may wear off the beater or wires on the whip may wear.
ENGLISH
*Accessory sold separately
USING THE STAND MIXER | 7
W10747071B_EN_v01.indd 7 |
|
|
2/29/16 2:15 PM |
|
|
USING THE STAND MIXER
OPERATING THE STAND MIXER
NOTE: The Stand Mixer may warm up during use. Under heavy loads with extended mixing time, the top of the unit may become hot. This is normal.
Plug the Stand Mixer into a grounded 3 prong outlet. Always set the speed control lever on
1 lowest speed to start, then gradually increase speed to avoid splashing ingredients. See the “Speed control guide” to select the best speed for your recipe.
NOTE: To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.
Do not scrape the bowl while the Stand Mixer is operating. The bowl and beaters are designed to provide
2 thorough mixing without frequent scraping. Scraping the bowl once or twice during mixing is usually sufficient.
8 | USING THE STAND MIXER
W10747071B_EN_v01.indd 8 |
|
|
2/29/16 2:15 PM |
|
|
USING THE STAND MIXER
NOTE: The pouring shield* can be used to avoid ingredients splashing out of the bowl when mixing as well as to easily pour ingredients in the bowl while mixing.
(OPTIONAL) Pour ingredients into the bowl through the pouring chute.
ENGLISH
DISASSEMBLING THE STAND MIXER
Raise the motor head: Check to be sure that the Stand Mixer is unplugged, and the speed control is
1 turned to “0”; then slide the locking lever to the unlock position and lift the motor head. Once lifted, slide the locking lever to the lock position to keep the motor head up.
Remove the accessory: Turn the speed control to “0”, unplug the Stand Mixer, and tilt the motor head
2 back; then, press the accessory upward as far as possible, turn the accessory clockwise and pull it away from the beater shaft.
*Accessory sold separately
(OPTIONAL) Remove the pouring shield*: Lift the front of the pouring shield* clear of the rim of the bowl, and pull away from the Stand Mixer.
Remove the bowl: Gently turn
3 the bowl counterclockwise to release it from the bowl clamping plate.
USING THE STAND MIXER | 9
W10747071B_EN_v01.indd 9 |
|
|
2/29/16 2:15 PM |
|
|
USING THE STAND MIXER
OPTIONAL ATTACHMENTS
KitchenAid offers a wide range of optional attachments such as the spiralizer, pasta cutters, or food grinder that may be attached to the Stand Mixer attachment power hub as shown here.
1 |
Check to be sure that the Stand |
2 |
Turn the attachment knob |
Mixer is unplugged, and the speed |
counterclockwise to remove |
||
|
control is turned to “0”. |
|
attachment hub cover. |
Insert attachment into attachment hub, making certain that attachment power shaft fits into the square attachment hub socket. It may be
3 necessary to rotate the attachment back and forth. When it is in the proper position, the pin on the attachment will fit into the notch on the hub rim.
Tighten the attachment knob by turning it clockwise until the
attachment is completely secured 4 to the Stand Mixer. See the
Instructions manual that came with your attachment for detailed
directions on using the attachment.
10 | USING THE STAND MIXER
W10747071B_EN_v01.indd 10 |
|
|
2/29/16 2:15 PM |
|
|
CARE AND CLEANING
CLEANING THE STAND MIXER
IMPORTANT: Do not wash the wire whip in the dishwasher. Do not immerse the Stand Mixer body in water or other liquids. These parts should be hand washed.
ENGLISH
Turn Stand Mixer off and unplug before cleaning. Wipe the Stand Mixer body with a soft, damp cloth.
1 Do not use household/commercial cleaners. Wipe off the beater shaft frequently to remove any accumulation of residue. Do not immerse in water.
The wire whip is not dishwasher safe. Clean it thoroughly in hot, sudsy
3 water and rinse completely before drying. Do not store the wire whip on the shaft.
The bowl, flat beater, dough hook, Flex Edge beater, and pouring shield* may be washed in a dishwasher (top
2 shelf only); or, clean them thoroughly in hot, sudsy water and rinse completely before drying. Do
not store beaters on the shaft.
FOR DETAILED INFORMATION ON CLEANING THE STAND MIXER:
Visit kitchenaid.com/quickstart for additional Instructions with videos, inspiring recipes, and tips on how to use your Stand Mixer.
*Accessory sold separately
CARE AND CLEANING | 11
W10747071B_EN_v01.indd 11 |
|
|
2/29/16 2:15 PM |
|
|
TROUBLESHOOTING
If your Stand Mixer should malfunction, please check the following:
1. The Stand Mixer may warm up during use. Under heavy loads with extended mixing time periods, you may not be able to comfortably touch the top of the unit. This is normal.
2. The Stand Mixer may emit a pungent odor, especially when new. This is common with electric motors.
3. If the flat beater hits the bowl, stop the Stand Mixer. See the “Assembling the Stand Mixer” section and adjust the beater to bowl clearance.
4. The speed control lever does not move smoothly or easily.
To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.
5. If your Stand Mixer should fail to operate, please check the following:
• Is the Stand Mixer plugged in?
• Is the fuse in the circuit to the Stand Mixer in working order? If you have a circuit breaker box, be sure the circuit is closed.
• Turn off the Stand Mixer for 10-15 seconds, then turn it back
on. If the Stand Mixer still does not start, allow it to cool for 30 minutes before turning it back on.
If the problem cannot be corrected: See the “Warranty and service” section. Do not return the Stand Mixer to the retailer; retailers do not provide service.
12 | TROUBLESHOOTING
W10747071B_EN_v01.indd 12 |
|
|
2/29/16 2:15 PM |
|
|
WARRANTY AND SERVICE
KITCHENAID® STAND MIXER WARRANTY FOR
THE 50 UNITED STATES, THE DISTRICT OF COLUMBIA, PUERTO RICO, AND CANADA
This warranty extends to the purchaser and any succeeding owner for Stand Mixers operated in the 50 United States, the District of Columbia, Puerto Rico, and Canada.
Length of Warranty: |
One Year Full Warranty from date of purchase. |
|
|
KitchenAid Will Pay |
Hassle-Free Replacement of your Stand Mixer. See |
for Your Choice of: |
the next page for details on how to arrange for |
|
service, or call the Customer eXperience Center |
|
toll-free at 1-800-541-6390. |
|
OR |
|
The replacement parts and repair labor costs to correct |
|
defects in materials and workmanship. Service must be |
|
provided by an Authorized KitchenAid Service Center. |
|
|
KitchenAid Will |
A. Repairs when your Stand Mixer is used in other |
Not Pay for: |
than normal single family home use. |
|
B. Damage resulting from accident, alteration, |
|
misuse or abuse. |
|
C. Any shipping or handling costs to deliver your |
|
Stand Mixer to an Authorized Service Center. |
|
D. Replacement parts or repair labor costs for |
|
Stand Mixer attachments operated outside the |
|
50 United States, District of Columbia, Puerto |
|
Rico, and Canada. |
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY
BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
IF THIS PRODUCT FAILS TO WORK AS WARRANTED, CUSTOMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT ACCORDING TO THE TERMS OF THIS LIMITED WARRANTY. KITCHENAID AND KITCHENAID CANADA DO NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province.
ENGLISH
WARRANTY AND SERVICE | 13
W10747071B_EN_v01.indd 13 |
|
|
2/29/16 2:15 PM |
|
|
WARRANTY AND SERVICE
HASSLE-FREE REPLACEMENT WARRANTY – 50 UNITED STATES, DISTRICT OF COLUMBIA, AND PUERTO RICO
We’re so confident the quality of our products meets the exacting standards of KitchenAid that, if your Stand Mixer should fail within the first year of ownership, KitchenAid will arrange
to deliver an identical or comparable replacement to your door free of charge and arrange to have your original Stand Mixer returned to us. Your replacement unit will also be covered by our one year limited warranty.
If your Stand Mixer should fail within the first year of ownership, simply call our
toll-free Customer eXperience Center at 1-800-541-6390 Monday through Friday. Please have your original sales receipt available when you call. Proof of purchase will be required to initiate the claim. Give the consultant your complete shipping address. (No P.O. Box numbers, please.)
When you receive your replacement Stand Mixer, use the carton, packing materials, and prepaid shipping label to pack up your original Stand Mixer and send it back to KitchenAid.
HASSLE-FREE REPLACEMENT WARRANTY – CANADA
We’re so confident the quality of our products meets the exacting standards of the KitchenAid brand that, if your Stand Mixer should fail within the first year of ownership, we will replace your Stand Mixer with an identical
or comparable replacement. Your replacement unit will also be covered by our one year limited warranty.
If your Stand Mixer should fail within the first year of ownership, simply call
our toll-free Customer eXperience Center
at 1-800-807-6777 Monday through Friday. Please have your original sales receipt available when you call. Proof of purchase will be required to initiate the claim. Give the consultant your complete shipping address.
When you receive your replacement Stand Mixer, use the carton, packing materials, and prepaid shipping label to pack up your original Stand Mixer and send it back to KitchenAid.
ARRANGING FOR SERVICE AFTER THE WARRANTY EXPIRES, OR ORDERING ACCESSORIES AND REPLACEMENT PARTS
In the United States and Puerto Rico:
For service information, or to order accessories or replacement parts, call toll-free at 1-800-541-6390 or write to:
Customer eXperience Center,
KitchenAid Small Appliances,
P.O. Box 218, St. Joseph, MI 49085-0218
Outside the United States and Puerto Rico:
Consult your local KitchenAid dealer or the store where you purchased the Stand Mixer for information on how to obtain service.
For service information in Canada:
Call toll-free 1-800-807-6777.
For service information in Mexico: Call toll-free 01-800-0022-767.
®/™ © 2016 KitchenAid. All rights reserved. Used under license in Canada.
14 | WARRANTY AND SERVICE
W10747071B_EN_v01.indd 14 |
|
|
2/29/16 2:15 PM |
|
|
PIÈCES ET CARACTÉRISTIQUES
PIÈCES ET ACCESSOIRES
Tête du moteur
Commande de vitesse
Fouet métallique
Crochet à pâte
*Clé vendue séparément
Prise à accessoires
FRANÇAIS
Arbre du batteur
Batteur plat
Bol
Batteur à côté souple*
Écran verseur*
PIÈCES ET CARACTÉRISTIQUES | 15
W10747071B_FR_v01.indd 15 |
|
|
2/29/16 2:18 PM |
|
|