KitchenAid KSSC36FMS, KSSC42FMS, KSSC48FMS, KSSS36FMB, KSSS42FMB user manual

SIDE BY SIDE BUILT-IN REFRIGERATOR

InstallationGuide

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

REFRIGERADOR EMPOTRADOS

DE DOS PUERTAS

Manualdeinstalación

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACIÓN REQUIERE DE 2 O MÁS PERSONAS.

RÉFRIGÉRATEUR ENCASTRÉS CÔTE À CÔTE

Guided’Installation

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE L’INTERVENTION DE 2 PERSONNES OU PLUS.

Table of Contents/Índice/Table des matières ..................................................................

2

2266811A

TABLE OF CONTENTS

REFRIGERATOR SAFETY .............................................................	3
DESIGN SPECIFICATIONS............................................................	4
Models..........................................................................................	4
Product Dimensions.....................................................................	6
Tipping Radius .............................................................................	7
Door Swing Dimensions...............................................................	7
Handle and Door Clearances.......................................................	8
Classic Series Factory Panels and Kits .....................................	11
Classic Series Custom Panels...................................................	11
Overlay Series Custom Panels ..................................................	13
Classic, Architect® and Pro Line™ Series Custom Side Panels .14
Overlay Series Custom Side Panels ..........................................	14
INSTALLATION REQUIREMENTS ..............................................	15
Tools and Parts ..........................................................................	15
Location Requirements..............................................................	16
Electrical Requirements .............................................................	17
Water Supply Requirements......................................................	17

INSTALLATION INSTRUCTIONS ................................................	18
Unpack Refrigerator ...................................................................	18
Reduce Tipping Radius..............................................................	18
Install Anti-Tip Boards................................................................	19
Connect Water Supply...............................................................	19
Plug in Refrigerator.....................................................................	20
Move Refrigerator to Final Position............................................	20
Lower Leveling Legs ..................................................................	20
Install Classic Series Custom Panels.........................................	20
Install Overlay Series Custom Panels ........................................	21
Level Refrigerator .......................................................................	22
Adjust and Remove Doors .........................................................	23
Install Side Panel ........................................................................	24
Install Base Grille........................................................................	24
Complete Installation..................................................................	24

ÍNDICE

SEGURIDAD DEL REFRIGERADOR...........................................	25
ESPECIFICACIONES DE DISEÑO ..............................................	26
Modelos......................................................................................	26
Medidas del producto................................................................	28
Arco de vuelco ...........................................................................	29
Medidas de oscilación de las puertas .......................................	29
Espacios para la agarradera y la puerta ....................................	30
Paneles y juegos de fábrica de la Serie Classic........................	33
Paneles de la puerta a la medida para la Serie Classic ............	33
Paneles a la medida de la Serie Overlay ...................................	35
Paneles laterales a la medida para las
Serie Classic, Architect® y Pro Line™ .........................................	36
Paneles laterales a la medida para la Serie Overlay..................	36
REQUISITOS DE INSTALACIÓN.................................................	37
Piezas y Herramientas ...............................................................	37
Requisitos de ubicación.............................................................	38
Requisitos eléctricos..................................................................	39
Requisitos del suministro de agua.............................................	39

INSTRUCCIONES DE INSTALACIÓN.........................................	40
Cómo desempacar su refrigerador............................................	40
Cómo reducir el arco de vuelco.................................................	40
Cómo instalar los tableros antivuelco........................................	41
Cómo conectar el suministro de agua.......................................	41
Cómo enchufar el refrigerador...................................................	42
Ubicación final del refrigerador ..................................................	42
Baje las patas niveladoras .........................................................	43
Cómo instalar los paneles a la medida para la Serie Classic....	43
Cómo instalar los paneles a la medida para la Serie Overlay ...	44
Cómo nivelar el refrigerador.......................................................	45
Ajuste y quite las puertas ...........................................................	45
Cómo instalar el panel lateral.....................................................	46
Cómo instalar la rejilla de la base ..............................................	47
Cómo terminar la instalación .....................................................	47

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................	48
SPÉCIFICATIONS DE DESIGN....................................................	49
Modèles......................................................................................	49
Dimensions du produit...............................................................	51
Rayon de basculement ..............................................................	52
Dimensions pour le pivotement des portes...............................	52
Dégagements pour les poignées et portes ...............................	53
Ensembles de panneaux d'origine de la série Classic..............	56
Panneaux personnalisés de la Série Classic.............................	56
Panneaux personnalisés de la série Overlay.............................	58
Panneaux latéraux personnalisés des
Séries Classic, Architect® et Pro Line™ .......................................	59
Panneaux latéraux personnalisés de la Série Overlay ..............	59
EXIGENCES D’INSTALLATION...................................................	60
Outillage et pièces nécessaires .................................................	60
Exigences d’emplacement.........................................................	61
Spécifications électriques .........................................................	62
Spécifications de l’alimentation en eau .....................................	62

INSTRUCTIONS D’INSTALLATION.............................................	63
Déballage du réfrigérateur..........................................................	63
Réduction du rayon de basculement.........................................	63
Installation de planches antibasculement..................................	64
Raccordement de la canalisation d’eau ....................................	65
Brancher le réfrigérateur.............................................................	65
Déplacement du réfrigérateur à l'emplacement final.................	65
Déploiement des pieds de nivellement......................................	66
Installation des panneaux personnalisés de la Série Classic....	66
Installation des panneaux personnalisés de la Série Overlay ...	67
Nivellement du réfrigérateur.......................................................	69
Ajustement et enlèvement des portes .......................................	69
Installation du panneau latéral ...................................................	70
Installation de la grille de la base ...............................................	71
Achever l’installation ..................................................................	71

2

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure do so can result in death or serious injury.

3

DESIGN SPECIFICATIONS

oo

Models - Side by Side Non-Dispensing Refrigerators

Architect® Series

Classic Series

Features wraparound styling that complements the contoured door handles. This series provides a warm commercial-looking built-in refrigerator.

Features factory-installed, traditional style trim to provide a “framed” look. This series requires the installation of custom panels that are not included.

KSSC36FMS KSSC42FMS KSSC48FMS

KSSS36FMB KSSS42FMB KSSS48FMB KSSS36FMX KSSS42FMX KSSS48FMX

Overlay Series

Features factory-installed, overlay style trim to provide a “frameless” look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36FMX KSSO42FMX KSSO48FMX

Pro LineTM Series

Features extraordinary design and exceptional levels of performance. This series is a perfect blend of form and function delivering professional quality, durability and simplicity.

KSSV42FMS KSSV42FMM

4

Models - Side by Side Dispensing Refrigerators

Architect® Series

Features wraparound styling that complements the contoured door handles. This series provides a warm commercial-looking built-in refrigerator.

KSSC36QMS KSSC42QMS KSSC48QMS

KSSC42QMU

Overlay Series

Features factory-installed, overlay style trim to provide a “frameless” look. This series requires the installation of custom panels, handles, and standoffs.

KSSO36QMB KSSO42QMB KSSO48QMB

KSSO36QMW KSSO42QMW KSSO48QMW

Classic Series

Features factory-installed, traditional style trim to provide a “framed” look. This series requires the installation of custom panels that are not included.

KSSS36QMB	KSSS42QMB	KSSS48QMB
KSSS36QMW	KSSS42QMW	KSSS48QMW
KSSS36QMX	KSSS42QMX	KSSS48QMX

Complete Series

Features factory-installed stainless steel trim and panels to create a sleek, contemporary look.

KSSP36QMS KSSP42QMS KSSP48QMS

5

ProductDimensions

Side View

■The depth from the front of the top grille to the back of the refrigerator cabinet is 25¹⁄ " (64 cm).

■The power cord is 84" (213 cm) long.

■The water line attached to the back of the refrigerator is 5 ft. (1.5 m) long.

■Height dimensions are shown with leveling legs extended ¹⁄ " (3 mm) below the rollers.

25¹⁄ "

(64 cm)

23¹⁄ "

(60 cm)

*83¹⁄ "

(211 cm)

84" (213 cm) Power Cord

*3¹⁄ " (9 cm)

*When leveling legs are fully extended to 1¹⁄ " (32 mm) below rollers, add 1¹⁄ " (29 mm) to the height dimensions.

Top View

A

251/8"

(64 cm)

	Model	Width A
	36	35" (89 cm)
	42	41" (104 cm)
	48	47" (119 cm)

Front View

■Width dimensions were measured from trim edge to trim edge.

■Height dimensions are shown with leveling legs extended ¹⁄ " (3 mm) below the rollers.

*831/8"

(211 cm)

A (see chart following)

Model	Width A (Trim edge to trim edge)
36	36¹⁄ " (92 cm)
42	42¹⁄ " (107 cm)
48	48¹⁄ " (123 cm)

*When leveling legs are fully extended to 1¹⁄ " (32 mm) below rollers, add 1¹⁄ " (29 mm) to the height dimensions.

6

TippingRadius

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

■The dolly wheel height must be added to the tipping radius when a dolly is used.

■If needed, the tipping radius can be reduced. See “Reduce Tipping Radius.”

Forward Tipping Radius

The forward tipping radius is the same for all models.

871/4"

(222 cm)

Side Tipping Radius

The side tipping radius varies depending upon the width of the model. Use the chart provided to determine the side tipping radius.

				A
		Model			Tipping Radius A
		36			90¹⁄ " (229.9 cm)
		42			93" (236.2 cm)
		48			96" (243.8 cm)

DoorSwingDimensions

The location must permit both doors to open to a minimum of 90°. Allow 4¹⁄ " (11.4 cm) minimum space between the side of the refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay panels or custom handles.

To adjust the door swing, see the “Adjust Doors” section.

36 Models

141/2"

(37 cm)

36

1/16"

40"

cm)

(92

cm)

(102

193/4"

(50 cm)

381

/2"

43

1/2

"

(98

cm)

(110

cm)

90˚

110˚

130˚

90˚

110˚

130˚

42 Models

171/2"

(44 cm)

38"

42

9/16"

(97 cm)

(108

cm)

231/4"

(59 cm)

41"

47"

(104 cm)

(119 cm)

90˚

110˚

130˚

90˚

110˚

130˚

48 Models

193/4"

(50 cm)

40"

451/

4"

(102

cm)

(115

cm)

263/4"

(68 cm)

431/2"

50

1/2

"

(110 cm)

(128

cm)

90˚

110˚

130˚

90˚

110˚

130˚

7

HandleandDoorClearances

If you are installing custom panels, the panels must allow certain clearances for the handles and for the doors to swing open. First, determine the types of handles you will be using and the door stop setting. Then, choose the appropriate scale drawing to use as a template for creating the panels.

Door

Custom Panel

		1/4" (6.35 mm)
		1/2" (1.3 cm)
	Classic	3/4" (1.9 cm)
		1" (2.5 cm)
	Handle
		11/4" (3.2 cm)
		11/2" (3.8 cm)
		13/4" (4.4 cm)
	Optional	2" (5.1 cm)
	Extended	Architect® Handle
		21/4" (5.7 cm)
	Handle	21/2" (6.4 cm)
		23/4" (7 cm)
		3" (7.6 cm)

		Handle Dimensions
		Actual Size
1"	2"	3"
(2.5 cm)	(5.1 cm)	(7.6 cm)

8

Overlay Series

Door Swing 90˚

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator

Side Trim

Hinge

Door	Backer
	Panel

1/4" (6.35 mm)

1/2" (1.3 cm)

3/4" (1.9 cm)

1" (2.5 cm)

11/4" (3.2 cm)

11/2" (3.8 cm)

1/2"

(1.3 cm)

3/4"

(1.9 cm)

1" (2.5 cm)

		11/4"
	PanelOverlay	(3.2	cm)
		11/2"

(3.8 cm)

Spacer Panel

9

NOTE: Do not place the door stop screw in the 130˚ position on Overlay Series models. See “Adjust and Remove Door.”

Overlay Series

Door Swing 110˚

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator	1"		2"
Side Trim	(2.5 cm)		(5.1 cm)
	3/4"		13/4"
(1.9 cm)			(4.4 cm)
1/2"			11/2"
(1.3 cm)			(3.8 cm)
1/4"		11/4"
(6.35 mm)	(3.2 cm)

Hinge					1/4" (6.35 mm)
					1/2" (1.3 cm)
					3/4" (1.9 cm)
					1" (2.5 cm)
					11/4" (3.2 cm)
					11/2" (3.8 cm)
		1/2"
		(1.3 cm)
		3/4"
		(1.9 cm)
				1"
		(2.5 cm)
			Overlay		11/4"
		Backer			(3.2 cm)
	Door				11/2"
					(3.8 cm)
		Panel		Panel
					Spacer Panel

10

ClassicSeriesFactoryPanelsandKits

All factory parts are available through your KitchenAid dealer or by calling KitchenAid Parts and Accessories at 1-800-442-9991. In Canada, call 1-800-807-6777.

Factory Door Panel Kits

Four kits containing colored acrylic or stainless steel door and top grille panels are available. Follow the kit instructions for installing the panels.

NOTE: Panel kits are not required for factory-installed stainless steel panel models.

Door Panel Part Numbers for Non-dispenser Models

Color	36	42	48
White	#2220852	#2220853	#2220854
Black	#2220855	#2220856	#2220857
Stainless	#2220861	#2220862	#2220863
Steel

Door Panel Part Numbers for Dispenser Models

Color	36	42	48
White	#2220864	#2220865	#2220866
Black	#2220867	#2220868	#2220869
Stainless	#2220873	#2220874	#2220875
Steel

Extended Door Handle Kits

Use extended door handles when additional finger clearance is needed between the door handles and custom panel. Follow the kit instructions for installing the door handles.

Color	Part Number
White	#4387990
Black	#8171418
Stainless Steel	#4388062
Matte Aluminum	#4387989

ClassicSeriesCustomPanels

If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. See dimensional drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may cause damage to your refrigerator.

NOTE: Dimensions shown have a (±) ¹⁄" (1.5 mm) tolerance. Panels that are more than ¹⁄ " (6.35 mm) thick must be routed. If panels are less than ¹⁄ " (6.35 mm) thick, install a filler panel between the doors and decorative panels.

Top Grille Panel

The top panel should not weigh more than 10 lbs. (4.5 kg).

A

							7¹⁄	"
							(18.4 cm)
		Model	A
		36	35³⁄ " (90 cm)
		42	41³⁄ " (105 cm)
		48	47³⁄ " (120 cm)

Door Panels for Non-dispenser Models

The freezer panel should not weigh more than 30 lbs. (13.5 kg). The refrigerator panel should not weigh more than 50 lbs. (23 kg).

A			B

707/16"

(179 cm)

Model	A	B
36	14¹⁄ " (36 cm)	19¹⁄ " (49 cm)
42	16³⁄ " (43 cm)	22³⁄ " (58 cm)
48	19¹⁄ " (49 cm)	26¹⁄ " (67 cm)

11

Door Panels for Dispenser Models

The two freezer panels combined should not weigh more than 30 lbs. (13.5 kg). The refrigerator panel should not weigh more than 50 lbs. (23 kg).

A						B

237/16"

(60 cm)

707/16"

(179 cm)

347/16"

(87 cm)

	Model	A	B
	36	14¹⁄ " (36 cm)	19¹⁄ " (49 cm)
	42	16³⁄ " (43 cm)	22³⁄ " (58 cm)
	48	19¹⁄ " (49 cm)	26¹⁄ " (67 cm)

Top Grille Panel – Routing Requirements

Top and bottom edges of the top panel should be edge routed ¹⁄ " (1.3 cm) and ³⁄ " (9.5 mm), respectively. Both ends should be edge routed ⁄ " (2.2 cm) as shown.

1/4"

1/4"

(6.35 mm)

(6.35 mm)

max.

Top

Top

max.

Grille

Grille

7/8"

7/8"

(2.2 cm)

(2.2 cm)

NOTE: When creating a panel with face detail, the offsets will be hidden and must be accounted for in order to center the detail in the top grille.

1/2"

(1.3 cm) min.

Center face detail between offsets

3/8"

(9.5 mm) min.

1/4"

(6.35 mm) max

Top

Bottom

1/4"

(6.35 mm) max

Door Panels – Routing Requirements

If an extended handle kit is used, then routing the handle side of the panels is not required. See “Classic Series Factory Panels and Kits” for more information on ordering extended handles.

If the standard handle is used, route the entire handle side of both panels 3¹⁄ " (8.25 cm) to allow for finger clearance. Then route the other sides 1" (2.54 cm).

Standard Handle – Top View

	31/4"
	(8.25 cm)		Hinge Side
	min.
Handle	1/4" (6.35 mm) max.	Door	Door
		Panel	Panel
	2" (5 cm)		1"
	min.		(2.54 cm)

Door Panel - Side View

1/4"

(6.35 mm)

max.

1/2" (1.3

Panel

12

OverlaySeriesCustomPanels

Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen décor, and to use custom handles for additional design flexibility.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a ¹/ " (3.18 mm) spacer panel or spacer strips and a ¹/ " (6.35 mm) backer panel.

IMPORTANT:

■The weight of the refrigerator door overlay panel cannot exceed 50 lbs. (23 kg).

■The weight of the freezer door overlay panel cannot exceed 30 lbs. (13.5 kg).

■The weight of the top grille overlay panel cannot exceed 10 lbs. (4.5 kg).

	Overlay Panel		Spacer Panel
			Backer Panel
	5/8" to 3/4"		1/4"
	(15.88 to
		1/8"	(6.35 mm)
	19.05 mm)
		(3.18 mm)

Spacer Panel

1/8"

(3.18mm)

1" minimum

(2.54 mm)

Door/Grille Trim

Offset Dimension

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

To minimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of full-sheet solid spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and sides edges of the backer panel. If you use spacer strips, it is also recommended that you use two 2"

(5.08 cm) strips horizontally centered for added support.

NOTE: For the grille and the door panels to be flush, the overlay door panel should be ¹⁄" (6.35 mm) thicker than the overlay grille panel.

81/2"

(21.59 cm)

Top Grille

C

73/8"

(18.73 cm)

F

Bottom Offset

1" (2.54 cm)

24" (60.96 cm)

343/4"

(88.27 cm)

	Freezer
	Dispenser
	A
	237/16"	Handle-Side
		Offset
	(59.53 cm)
		1/8" (3.2 mm)
	D
	Bottom Offset
	1/8" (3.2 mm)
	A
	D
	347/16"	Handle-Side
		Offset
	(87.47 cm)
		1/8" (3.2 mm)
	Bottom Offset
	1/8" (3.2 mm)

Freezer
Non-Dispenser	Refrigerator

A	B
Handle-Side
Offset
1/8" (3.2 mm)
701/2"	701/2"
(179.07 cm)	(179.07 cm)
711/16"
(180.50 cm)
D	E
Bottom Offset	Bottom Offset
1/8" (3.2 mm)	1/8" (3.2 mm)

Decorative Overlay Panels

Model	A	B	C
36	14⁄" (37.15 cm)	19⁄" (49.85 cm)	34¹⁄" (87.63 cm)
42	17¹⁄" (43.50 cm)	23¹⁄" (58.74 cm)	40¹⁄" (102.87 cm)
48	19⁄" (49.85 cm)	26⁄" (67.63 cm)	46¹⁄" (118.11 cm)

Backer Panels

Model	D	E	F
36	14⁄" (36.67 cm)	19⁄" (49.37 cm)	34¹⁄" (87.63 cm)
42	16¹ ⁄" (43.50 cm)	22¹ ⁄" (58.26 cm)	40¹⁄" (102.87cm)
48	19⁄" (49.37 cm)	26⁄" (67.15 cm)	46¹⁄" (118.11 cm)

13

Classic,Architect® andProLine™ Series

Custom Side Panels

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel is determined by the type of installation you are planning.

NOTES:

■The dimensions shown are actual product dimensions and may not reflect the needed panel installation dimensions.

■The side panel should be a minimum of ¹⁄ " (1.3 cm) thick to prevent warping.

■If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

Refrigerator

241/8"

(61.3 cm)

2311/16"

(60.3 cm)

231/2"

(59.7 cm)

Side Trim

1/4"

(6.35 mm)

5/32"

(4 mm)

1/16"

(1.5 mm)

7/32"

(5.5 mm)

13/32" (10 mm)

Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall. Add ⁄ " (5.6 mm) to this measurement to allow the side panel to fit into the trim.

2.If the panel is more than ¹⁄ " (6.35 mm) thick, route the front edge to allow the side panel to fit into the trim.

A

Flush Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall.

2.Attach the support board with a screw or adhesive that is compatible with aluminum and wood.

A

Recessed Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall.

2.Route the front edge of the support board or attach a ¹⁄ " (6.35 mm) board to hold the panel in the cabinet side trim.

A

OverlaySeriesCustomSidePanels

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

■The dimensions shown are actual product dimensions and may not reflect the needed installation dimensions.

■The side panel should be a minimum of ¹⁄ " (12 mm) thick to prevent warping.

■If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

14

Refrigerator

Overlay

233/8"

(59.40 cm)

Side Trim

3/16"

(4.5 mm)

3/8"

(9.7 mm)

1/16"

(1.5 mm)

1/8"

(3.2 mm)

Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall. Add ¹⁄ " (0.8 mm) to this measurement to allow the side panel to fit into the trim.

2.If the panel is more than ³⁄ " (9.5 mm) thick, route the front edge to allow the side panel to fit into the trim.

A

Recessed Inset Installation Dimensions

1.Measure the distance from point A (as shown) to back wall.

2.Route the front edge of the support board or attach a ³⁄ " (9.5 mm) board to hold the panel in the cabinet side trim.

A

INSTALLATION

REQUIREMENTS

ToolsandParts

IMPORTANT:

■Installer: Leave Installation Instructions with the homeowner.

■Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use.

TOOLS NEEDED:

Make sure that you have the tools necessary for proper installation:

■ Hand drill or electric drill		■ T27 flat-head 6 point
	(properly grounded)		driver
■	Drill bits	■	¹¹⁄ " nut driver
■	Two adjustable wrenches	■	³⁄ " and ¹⁄ " open-end
			wrenches
■	Phillips screwdriver	■	⁄ " Allen wrench
■	Small level	■	⁄ " socket wrench
■	Appliance dolly	■	Tape measure

PARTS NEEDED:

■Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

■One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

■Order factory panels, make custom panels or consult a qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Design Specifications” for more information.

Overlay Series: Make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Installation Requirements” and “Design Specifications” for more information.

Pro Line™, Complete and Architect® Series are shipped complete.

■If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄ " (6.35 mm) compression fitting.

15

	LocationRequirements	■ A grounded 3 prong electrical outlet should be placed within
		4" (10.2 cm) of the right side cabinets or end panel. See
		“Electrical Requirements” for additional information.
	The refrigerator can be recessed in an opening between cabinets
		■ The water shutoff should be located in the base cabinet on
	or installed at the end of a cabinet run using a side panel to
	enclose the refrigerator.	either side of the refrigerator or some other easily accessible
		area. If the water shutoff valve is not in the cabinets, the
	WARNING	plumbing for the water line can come through the floor or the
		back wall. See “Water Supply Requirements” for more
		information.

Explosion Hazard			80" - 90"
			(203-229 cm)
Keep flammable materials and vapors, such as							4"
						(10.2 cm)
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT:
		831/4" (211.5 cm) min.
■ Observe all governing codes and ordinances.
		843/4" (215 cm) max.
■ Do not install the refrigerator near an oven, radiator, or		to bottom of solid soffit
other heat source, nor in a location where the temperature
will fall below 55°F (13°C).

■Floor must support the refrigerator weight, more than

600 lbs. (272 kg), door panels and contents of the				77"
refrigerator.				(196 cm)

■Ceiling height must allow for side or front tipping radius. See “Tipping Radius.”

■ Location should permit doors to open fully. See “Door						A
						Width
Swing Dimensions.”					(see chart following)

■Location must permit top grille removal. See “Opening Dimensions.”

6"

(15.2 cm)

Opening Dimensions

■The solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or

one is not available, then the refrigerator must be braced to

3" (7.6 cm)

prevent tipping during use.

11"

If the anti-tip boards are needed, they must be attached to

(28 cm)

231/2"

the rear wall studs 80" to 90" (203 cm to 229 cm) above the

(60 cm) min.

6"

floor. See “Install Anti-Tip Boards” for more information.

6"

(15.2 cm)

(15.2

cm)

NOTE: A clearance of ¹⁄ " (1.3 cm) must be maintained above

the top grille in order for the top grille to be removed.

Model

Width A (as shown above)

36

35¹⁄ " (90.2 cm)

42

41¹⁄ " (105.4 cm)

48

47¹⁄ " (120.7 cm)

1/2"

(1.3 cm)

16

ElectricalRequirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

WaterSupplyRequirements

■All installations must meet local plumbing code requirements.

■The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible area. The right-hand side is recommended. The access hole through the right-hand side cabinet must be within ¹⁄ "

(12.7 mm) of the rear wall.

6" (15.2 cm)

3" (7.6 cm)

11" 231/2" (28 cm)

(60 cm) min. 6" 6"

(15.2 cm) (15.2 cm)

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker box.

When you are finished, turn ON the master power switch or reconnect power at the circuit breaker box. Then reset the control to the desired setting.

■If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. A ¹⁄ " (12.7 mm) hole for plumbing should be drilled 6"

(15.2 cm) to 12" (30.4 cm) from the right-hand side cabinet or panel. On the floor, the hole should be no more than 11"

(28 cm) away from the back wall. On the wall, the hole should be no more than 3" (7.6 cm) up from the floor. See “Connect Water Supply.”

If this recommended water line location is used, no additional plumbing must be purchased.

■If additional tubing is needed, use copper tubing and check for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

■Do not use a piercing-type or ³⁄ " (4.76 mm) saddle valve which reduces water flow and clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄ " (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Cold Water Supply

Connect the ice maker to a cold water line with water pressure between 20 and 120 psi (138 - 827 kPa). If you have questions about your water pressure, call your utility company.

17

INSTALLATION INSTRUCTIONS

UnpackRefrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure do so can result in death or serious injury.

IMPORTANT:

■Do not remove the protective film or cardboard from door or grille until the refrigerator is in its operating position.

■All 4 leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

■Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating position.

1.Remove the 4 brackets (2 on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

2.Place an appliance dolly under the freezer side of the refrigerator. Be sure to protect the side trims and handles. Place the corner posts from the packing materials over the trims and handles as appropriate. Carefully tighten the strap.

NOTE: Pass the dolly strap under the handles for the Architect® Series.

ReduceTippingRadius

(ifrequired)

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See “Tipping Radius” in the “Installation Requirements and Design Specifications” section for more information.

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

	Model	Reduced Tipping Radius
	36	88" (223.5 cm)
	42	88¹⁄ " (224.8 cm)
	48	89¹⁄ " (226.7 cm)

Classic and Overlay Series

1.Grasp both ends of the top grille.

2.Push the top grille straight up, then pull straight out. Lay the grille on a soft surface.

B A B

A.Top grille

B.Cabinet side trim

3.Remove the 6 screws attaching each cabinet side trim to the refrigerator and remove the side trims.

4.Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

5.Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

Architect® Series

1.Grasp both ends of the louver panel. Push the louver panel straight up, then pull straight out. Lay the panel on a soft surface.

2.Grasp both ends of the top grille. Push the top grille straight up, then pull straight out. Lay the top grille on a soft surface.

B A B

3.Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

C

A.Top grille

B.Cabinet side trim

C.Louver panel

18

3.Remove the 6 screws attaching each cabinet side trim to the refrigerator and remove the side trims.

4.Stand the refrigerator up by first placing the left bottom edge of the refrigerator on the floor, standing the refrigerator upright and then lowering the right-hand side of the refrigerator down to the floor.

5.Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

Pro Line™ Series

1.Grasp both ends of the top grille.

2.Push the top grille straight up, and then pull straight out.

3.Disconnect the wiring harness from the back of the top grille.

4.Lay the top grille on a soft surface.

5.Remove the 6 screws that attach each cabinet side trim to the refrigerator, and remove the side trims.

6.Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

7.After the dolly has been removed from the refrigerator, reassemble the trim.

8.Reattach wiring harness into grille back.

9.Insert top grille hooks into slots on the side trim. Pull grille down slightly to lock into place.

InstallAnti-TipBoards

IMPORTANT:

■The solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, prevent the refrigerator from tipping during use as shown.

■It is recommended that board(s) be installed before the refrigerator is installed.

■Board(s) must be long enough to fully cover the width of the compressor cover.

■Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

■During installation, raise the refrigerator up so there is ¹⁄ " (6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the condenser cover when raising the rear leveling legs.

To Install Anti-tip Boards

1.Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

2.Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x

81 cm) wood boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 mm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1½" (3.8 cm). The board(s) must overlap the compressor cover.

A B

C

2" (5 cm)

D

A.Center board ¹⁄" (6.35 mm) max. above refrigerator

B.Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C.Attach to studs with six #8 x 3" (7.6 cm) screws

D.Compressor cover

ConnectWaterSupply

1.Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

2.Before attaching copper tubing to the refrigerator, flush at least 2 qt. (1.9 L) of water through the copper tubing and into a bucket to get rid of any particles in the water line.

3.Check for leaks around the saddle valve. Do not overtighten the clamp or sleeve. This will crush the copper tubing.

4.Make connection to the refrigerator.

Style 1 - Connecting to a Water Valve:

NOTE: The water shutoff valve should be located in the base cabinet on either side of the refrigerator. The right-hand side is recommended. The access hole through the right cabinet must be within ¹⁄ " (12.7 mm) of rear wall.

Push the bulb end of the tubing into the water valve as far as it will go. Slide the nut forward and finger tighten. Then tighten it with a wrench two more turns. Do not overtighten.

A

B

A.Bulb

B.Nut (provided)

19

Style 2 - Connecting to a Water Line

Additional Parts Needed: Coupling, ferrule and nut.

Slide the purchased nut then the purchased ferrule onto the tubing. Push the tubing into the purchased coupling as far as it will go. Slide the nut and ferrule forward. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

LowerLevelingLegs

NOTE: All 4 leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

Use socket wrench to turn leg levelers on both sides of refrigerator to the right (clockwise) until refrigerator weight is supported by leveling legs. The rollers should be off the floor. To avoid cabinet damage, do not apply more than 50 inch - pounds (58 cm - kg) of torque to the leveling legs.

A	B	C	D	E F
A. Line to refrigerator			D. Coupling (purchased)
B. Nut (provided)			E. Ferrule (purchased)
C. Bulb			F. Nut (purchased)

5.Turn shutoff valve ON.

6.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

PluginRefrigerator

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

7.Set control switch at top of cabinet to the OFF position.

8.Plug into grounded 3 prong outlet.

MoveRefrigeratortoFinalPosition

IMPORTANT: To prevent floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1.Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2.Do not remove protective film or cardboard from door or grille.

3.Move the refrigerator straight back and evenly into the opening. Check to make sure that water tubing is not kinked and the power supply cord is on top of the refrigerator next to the cover.

A B

A.Rear leveling legs

B.Front leveling legs

InstallClassicSeriesCustomPanels

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would prevent the refrigerator from being serviced.

Door Panels

1.Remove all tape and door bracing from the refrigerator and freezer doors.

2.Remove the screws that attach the handles to the door frame.

3.Slide the decorative door panels into the door frames.

4.If needed, route the door panels or install a filler panel between the doors and the decorative panels. See the “Classic Series Custom Panels” section.

A A

A. Panels

20

5.Replace the door handles. Check to be sure that the top of both door handles are aligned.

6.If the door handles are not aligned, loosen all handle screws and adjust door handles up or down. Tighten the screws. If any of the door screws are damaged, replace them with additional screws provided in the parts package.

Top Grille Panel

1.Grasp both ends of the top grille.

2.Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

B A B

A.Top grille

B.Cabinet side trim

3.Remove one end cap by loosening the nuts and sliding the end cap off.

A
C
B
D
A. Bottom rail	C. End cap
B. Nuts	D. Top rail

4.Slide the decorative panel into the top grille channel and reattach the end cap.

A

A.Backer panel

5.Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

B A B

A. Top grille

B. Cabinet side trim

InstallOverlaySeriesCustomPanels

IMPORTANT:

■Install the custom handles prior to installing the panels on the refrigerator. For more information on KitchenAid custom handle selection, refer to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230.

In Canada, visit www.KitchenAid.ca, or call

1-800-806-6777.

■Create custom door overlay panels according to the specifications in the “Overlay Series Custom Panels” section.

■KitchenAid is not responsible for the removal or addition of molding or decorative panels that would prevent the refrigerator from being serviced.

Door Panel Installation

1.Remove all tape and door bracing from the refrigerator and freezer doors.

2.Open the refrigerator and freezer compartment doors.

3.Remove the handle side and top trims.

AA

A.Trims

4.Slide the custom panels into the bottom and hinge side trims on the refrigerator compartment and freezer compartment doors, making sure that the backer panel fits into the hinge side trims.

A A

A.Panels

5.Reinstall the handle-side and top trims.

21

6.Remove the protective skin from the screw covers. Snap the screw covers into the handle trim section.

Top Grille Panel

1.Grasp both ends of the top grille.

2.Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

B A B

A.Top grille

B.Cabinet side trim

3.Remove one end cap by loosening the nuts and sliding the end cap off.

A
C
B
D
A. Bottom rail	C. End cap
B. Nuts	D. Top rail

4.Slide the decorative panel into the top grille channel and reattach the end cap.

A

A. Backer panel

5.Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

B A B

A.Top grille

B.Cabinet side trim

LevelRefrigerator

NOTE: Classic and Overlay Series door panels must be installed before leveling.

1.Open the doors and place the level on top of the refrigerator frame as shown. Check to see whether the refrigerator is level from left to right.

A

B

B

A.Level to check left to right leveling

B.Level to check front to back leveling

2.Use the leveling bolts to adjust the leveling legs until the refrigerator is level from left to right.

A	A
B	B

A.Rear leveling bolt

B.Front leveling bolt

3.Place the level(s) on shelf or shelves as shown. Check to see whether the refrigerator is level from front to back.

4.Use the leveling bolts to adjust the leveling legs until the refrigerator is level from front to back.

5.Be sure that all 4 leveling legs contact the floor and support the full weight of the refrigerator.

6.Make final check to ensure the refrigerator is level.

22