KITCHENAID KBUDT4255E, KBUDT4855E, KBUDT4265E, KBUDT4865E, KBUIT4875E Installation Instructions

INSTALLATION

INSTRUCTIONS

For Built-in Refrigerators

INSTRUCCIONES DE INSTALACIÓN

Para los refrigeradores empotrados

INSTRUCTIONS

D’INSTALLATION

Pour réfrigérateurs encastrés

Side by Side Models/ Modelos con dos puertas/ Modèles côte à côte KBUIT4255E, KBUDT4255E KBUIT4265E, KBUDT4265E KBUIT4275E, KBUDT4275E KBUIT4855E, KBUDT4855E KBUIT4865E, KBUDT4865E KBUIT4875E, KBUDT4875E

W10291427A

TABLE OF CONTENTS

REFRIGERATOR SAFETY...........................................................................	3
DESIGN SPECIFICATIONS.........................................................................	4
Models - Side by Side Non-Dispensing Refrigerators .............................	4
Models - Side by Side Dispensing Refrigerators .....................................	5
Product Dimensions .................................................................................	6
Tipping Radius ..........................................................................................	7
Door Swing Dimensions ...........................................................................	7
Handle and Door Clearances for Custom Panel Series...........................	8
Custom Panels........................................................................................	10
Full-Overlay Custom Panels ...................................................................	12
Stainless Steel Series Side Panels .........................................................	13
Custom Panel Series Side Panels ..........................................................	14
INSTALLATION REQUIREMENTS ...........................................................	14
Tools and Parts.......................................................................................	14
Location Requirements...........................................................................	15
Electrical Requirements..........................................................................	16
Water Supply Requirements...................................................................	16

INSTALLATION INSTRUCTIONS .............................................................	17
Unpack the Refrigerator .........................................................................	17
Reduce Tipping Radius ..........................................................................	17
Move the Refrigerator into House ..........................................................	17
Install Anti-Tip Boards ............................................................................	18
Connect the Water Supply .....................................................................	18
Plug in Refrigerator.................................................................................	20
Move Refrigerator to Final Location.......................................................	20
Lower Leveling Legs...............................................................................	20
Install Custom Panels.............................................................................	20
Level Refrigerator....................................................................................	21
Adjust Doors ...........................................................................................	22
Install Side Panel ....................................................................................	22
Install Base Grille ....................................................................................	22
Complete Installation..............................................................................	23
Water System Preparation .....................................................................	23

ÍNDICE

SEGURIDAD DEL REFRIGERADOR........................................................	24
ESPECIFICACIONES DE DISEÑO ...........................................................	25
Modelos - Refrigeradores de dos puertas sin despachador .................	25
Modelos - Refrigeradores de dos puertas con despachador................	26
Medidas del producto.............................................................................	27
Arco de vuelco ........................................................................................	28
Medidas de oscilación de las puertas....................................................	28
Espacios para la agarradera y la puerta para
la serie de paneles a la medida ..............................................................	29
Paneles a la medida................................................................................	31
Paneles a la medida totalmente recubiertos..........................................	33
Paneles laterales de la serie de acero inoxidable ..................................	34
Paneles laterales para la serie de paneles a la medida .........................	35
REQUISITOS DE INSTALACIÓN ..............................................................	35
Piezas y herramientas.............................................................................	35
Requisitos de ubicación .........................................................................	36
Requisitos eléctricos...............................................................................	37
Requisitos del suministro de agua .........................................................	37

INSTRUCCIONES DE INSTALACIÓN......................................................	38
Cómo desempacar su refrigerador ........................................................	38
Cómo reducir el arco de vuelco .............................................................	38
Cómo hacer entrar el refrigerador en la casa ........................................	39
Cómo instalar los tableros antivuelco ....................................................	39
Conexión del suministro de agua...........................................................	40
Cómo enchufar el refrigerador ...............................................................	41
Cómo mover el refrigerador a su ubicación final ...................................	42
Baje las patas niveladoras......................................................................	42
Cómo instalar los paneles a la medida ..................................................	42
Cómo nivelar el refrigerador ...................................................................	43
Cómo ajustar las puertas .......................................................................	43
Cómo instalar el panel lateral .................................................................	44
Cómo instalar la rejilla de la base...........................................................	44
Cómo terminar la instalación..................................................................	45
Preparación del sistema de agua...........................................................	45

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ...........................................................	46
SPÉCIFICATIONS DE DESIGN.................................................................	47
Modèles - Réfrigérateurs côte à côte sans distributeur.........................	47
Modèles - Réfrigérateurs côte à côte avec distributeur.........................	48
Dimensions du produit............................................................................	49
Rayon de basculement...........................................................................	50
Dimensions pour l'ouverture des portes ................................................	50
Dégagements pour les poignées et portes pour
la série de panneaux personnalisés .......................................................	51
Panneaux personnalisés.........................................................................	53
Panneaux de revêtement personnalisés ................................................	55
Panneaux latéraux de la série de panneaux en acier inoxydable..........	56
Panneaux latéraux de la série de panneaux personnalisés...................	57
EXIGENCES D’INSTALLATION ................................................................	57
Outillage et pièces ..................................................................................	57
Exigences d’emplacement .....................................................................	58
Spécifications électriques ......................................................................	59
Spécifications de l’alimentation en eau..................................................	59

INSTRUCTIONS D’INSTALLATION .........................................................	60
Déballage du réfrigérateur......................................................................	60
Réduction du rayon de basculement .....................................................	60
Faire entrer le réfrigérateur dans le domicile..........................................	61
Installation de planches antibasculement..............................................	61
Raccordement à l'alimentation en eau...................................................	62
Brancher le réfrigérateur.........................................................................	63
Déplacement du réfrigérateur à l'emplacement final.............................	64
Déploiement des pieds de nivellement ..................................................	64
Installation des panneaux personnalisés ...............................................	64
Nivellement du réfrigérateur ...................................................................	65
Ajustement des portes............................................................................	66
Installation du panneau latéral................................................................	66
Installation de la grille de la base ...........................................................	67
Achever l’installation...............................................................................	67
Préparation du système d’eau ...............................................................	67

2

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

3

DESIGN SPECIFICATIONS

Models - Side by Side Non-Dispensing Refrigerators

Stainless Steel Series

Features stainless steel exterior styling. KBUIT4255E KBUIT4265E KBUIT4855E KBUIT4865E

Custom Panel Series

Features factory-installed, traditional style trim to provide a “framed” look. This series requires the installation of custom panels that are not included.

KBUIT4275E KBUIT4875E

TRIMKITSXS - Trimless Trim Kit

On the Custom Panel Series, you can create a “frameless” look using full-overlay custom panels. You will need to order a Trimless Trim Kit for Side by Sides TRIMKITSXS. This accessory kit contains parts to replace the factory trim.

Full-overlay custom panels and handles are required but not included in the accessory kit. Create the panels according to the specifications in the “Full-Overlay Custom Panels” section. You can order a set of Thermador’s Handles or select handles from another source. For door clearances, see “Handle and Door Clearances for Custom Panel Series.”

Handle Kits

For use with Stainless Steel models. You can purchase a handle type other than that provided with your model. See your dealer for Details.

CURVHNDL10 - Curved Handle Kit PROHNDL160 - Pro Handle Kit PROHNDL165 - Designer Pro Handle Kit MASTHNDL55 - Masterpiece Handle Kit

EXTHANDSXS - Extended Handle Kit for Side by Sides

This kit may be required if you install a custom raised panel. See “Handle and Door Clearances for Custom Panel Series.”

4

Models - Side by Side Dispensing Refrigerators

Stainless Steel Series

Features stainless steel exterior styling. KBUDT4255E KBUDT4265E KBUDT4855E KBUDT4865E

Custom Panel Series

Features factory-installed, traditional style trim to provide a “framed” look. This series requires the installation of custom panels that are not included.

KBUDT4275E KBUDT4875E

TRIMKITSXS - Trimless Trim Kit

On the Custom Panel Series, you can create a “frameless” look using full-overlay custom panels. You will need to order a Trimless Trim Kit for Side by Sides TRIMKITSXS. This accessory kit contains parts to replace the factory trim.

Full-overlay custom panels and handles are required but not included in the accessory kit. Create the panels according to the specifications in the “Full-Overlay Custom Panels” section. You can order a set of Thermador’s Handles or select handles from another source. For door clearances, see “Handle and Door Clearances for Custom Panel Series.”

Handle Kits

For use with Stainless Steel models. You can purchase a handle type other than that provided with your model. See your dealer for Details.

CURVHNDL10 - Curved Handle Kit PROHNDL160 - Pro Handle Kit PROHNDL165 - Designer Pro Handle Kit MASTHNDL55 - Masterpiece Handle Kit

EXTHANDSXS - Extended Handle Kit for Side by Sides

This kit may be required if you install a custom raised panel. See “Handle and Door Clearances for Custom Panel Series.”

5

Product Dimensions

Side View

■The depth from the front of the top grille to the back of the refrigerator cabinet is 25¹⁄ " (64 cm).

■The power cord is 84" (61 cm) long.

■The water line attached to the back of the refrigerator is 5 ft (1.5 m) long. Height dimensions are shown with leveling legs extended ¹⁄ " (3 mm) below the rollers.

A

23¹⁄ "

(59.7 cm)

*83³⁄ "

(211.8 cm)

84" (213.4 cm) Power Cord

*3¹⁄ " (8.9 cm)

*When leveling legs are fully extended to 1¹⁄ " (32 mm) below rollers, add 1¹⁄ " (29 mm) to the height dimensions.

Top View

Front View

■Width dimensions were measured from trim edge to trim edge.

■Height dimensions are shown with leveling legs extended ¹⁄ " (3 mm) below the rollers.

*83³⁄ "

(211.8 cm)

				A
					following)
			(see chart
Model				Width A (Trim edge to trim edge)
42" (106 cm)				42¹⁄ " (107 cm)
48" (122 cm)				48¹⁄ " (123 cm)

*When leveling legs are fully extended to 1¹⁄ " (32 mm) below rollers, add 1¹⁄ " (29 mm) to the height dimensions.

A

25¹⁄"

(64 cm)

Model		Width A
42" (106 cm)		41" (104 cm)
48" (122 cm)		47" (119 cm)

6

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

■The dolly wheel height must be added to the tipping radius when a dolly is used.

■If needed, the tipping radius can be reduced. See “Reduce Tipping Radius.”

Side Tipping Radius

The side tipping radius varies depending upon the width of the model. Use the chart provided to determine the side tipping radius.

NOTE: Tip on side only.

			A
Model					Tipping Radius A
42" (106 cm)					93" (236.2 cm)
48" (122 cm)					96" (243.8 cm)

Door Swing Dimensions

The location must permit both doors to open to a minimum of 90°. Allow 4¹⁄" (11.4 cm) minimum space between the side of the refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay panels or custom handles.

To adjust the door swing, see “Adjust Doors.”

42" (106 cm) Models

12 ⁄ "

(32.1 cm)

37¹⁄ "	41¹⁄ "
(94.6 cm)	(105.4 cm)
	16 ⁄ "
	(42.9 cm)
41³⁄ "	47 ⁄ "
(105.1 cm)	(121.6 cm)
	90˚
	110˚
	130˚
	90˚
	110˚
	130˚

48" (122 cm) Models

14³⁄ "

(36.5 cm)

39"

44"

(99.1

cm)

(111.8

cm)

19¹⁄ "

(48.9 cm)

43

⁄ "

51

³⁄ "

(111.4 cm)

(130.5 cm)

90˚

110˚

130˚

90˚

110˚

130˚

7

Handle and Door Clearances for Custom Panel Series

If you are installing custom panels, the panels must allow certain clearances for the handles and for the doors to swing open. An Extended Handle Kit may be required if you install a custom raised panel. See the “Models” section under “Design Specifications.”

Door

Custom Panel

		1/4" (6.35 mm)
		1/2" (1.3 cm)
	Custom	3/4" (1.9 cm)
		1" (2.5 cm)
	Panel
		11/4" (3.2 cm)
	Series
	Handle	11/2" (3.8 cm)
		13/4" (4.4 cm)
	Optional	2" (5.1 cm)
	Extended	21/4" (5.7 cm)
	Handle	21/2" (6.4 cm)
		23/4" (7 cm)
		3" (7.6 cm)

		Handle Dimensions
		Actual Size
1"	2"	3"
(2.5 cm)	(5.1 cm)	(7.6 cm)

8

NOTE: To use full-overlay custom panels, you must order the Trimless Trim Kit. Additionally, you will need to order either a set of Thermador's Handles or select handles from another source. See the “Models” section of “Design Specifications” for more information and specific kit.

Custom Panel Series

Clearances for

Full-Overlay Custom Panels

Door Swing 110˚

Actual Size

Refrigerator	1"		2"
Side Trim	(2.5 cm)		(5.1 cm)
	3/4"		13/4"
(1.9 cm)			(4.4 cm)
1/2"			11/2"
(1.3 cm)			(3.8 cm)
1/4"		11/4"
(6.35 mm)	(3.2 cm)

Hinge					1/4" (6.35 mm)
					1/2" (1.3 cm)
					3/4" (1.9 cm)
					1" (2.5 cm)
					11/4" (3.2 cm)
					11/2" (3.8 cm)
		1/2"
		(1.3 cm)
		3/4"
		(1.9 cm)
				1"
		(2.5 cm)
			Custom		11/4"
		Backer			(3.2 cm)
	Door				11/2"
					(3.8 cm)
		Panel		Panel
					Spacer Panel

9

Custom Panels

If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. See dimension drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may cause damage to your refrigerator.

NOTE: Dimensions shown have a (±)¹⁄ " (1.5 mm) tolerance. Panels that are more than ¹⁄ " (6 mm) thick must be routed. If panels are less than ¹⁄ " (6 mm) thick, install a filler panel between the doors and decorative panels.

Top Grille Panel

The top panel should not weigh more than 10 lbs (4.5 kg) total weight.

A

7"

(17.8

cm)

Model

A

42" (106.6 cm)

40¹⁄ " (105 cm)

48" (122 cm)

46¹⁄ " (120 cm)

Door Panels for Non-dispenser Models

The freezer panel should not weigh more than 30 lbs (13.5 kg) total weight. The refrigerator panel should not weigh more than 50 lbs (23 kg) total weight.

A			B

Door Panels for Dispenser Models

The two freezer panels combined should not weigh more than 30 lbs (13.5 kg) total weight. The refrigerator panel should not weigh more than 50 lbs (23 kg) total weight.

A						B

23⁄"

(59.5 cm)

70⁄"

(179 cm)

34⁄"

(87.4 cm)

Model		A	B
42"	(106.6 cm)	16³⁄ " (42.5 cm)	22³⁄ " (57.8 cm)
48"	(122 cm)	19¹⁄ " (48.9 cm)	26¹⁄ " (66.8 cm)

70¹⁄"

(179.1 cm)

Model		A	B
42"	(106.7 cm)	16³⁄ " (42.5 cm)	22³⁄ " (57.8 cm)
48"	(122 cm)	19¹⁄ " (48.9 cm)	26¹⁄ " (66.8 cm)

10

Top Grille Panel – Routing Requirements

Top and bottom edges of the top panel should be edge routed ¹⁄ " (1.3 cm) and ³⁄ " (9.5 mm), respectively. Both ends should be edge routed ⁄ " (2.2 cm) as shown.

¹⁄ "

(6.35 mm)

max.

Top

Top

Grille

Grille

⁄ "

⁄ "

(2.2 cm)

(2.2 cm)

¹⁄ "

(6.35 mm) max.

NOTE: When creating a panel with face detail, the offsets will be hidden and must be accounted for in order to center the detail in the top grille.

¹⁄ " (1.3 cm) min.

Center face detail between offsets

³⁄ " (9.5 mm)

min.

¹⁄ "

(6.35 mm) max.

Top

Bottom

¹⁄ "

(6.35 mm) max.

Door Panels – Routing Requirements

If an extended handle kit is used, then routing the handle side of the panels is not required. See “Handle and Door Clearances” for more information on ordering extended handles.

If the standard handle is used, rout the entire handle side of both panels 3¹⁄ " (8.25 cm) to allow for finger clearance. Then rout the other sides 1" (2.54 cm).

Standard Handle – Top View

3¹⁄ "

(8.25 cm)

	min.		Hinge Side
<![if ! IE]> <![endif]>Handle	¹⁄ " (6.35 mm) max.	Door	Door
		Panel	Panel
	2" (5 cm)		1"
	min.		(2.54 cm)

Door Panel - Side View

	¹⁄ "
	(6.35 mm)
<![if ! IE]> <![endif]>Panel	max.
	¹⁄ " (1.

11

Full-Overlay Custom Panels

	Custom overlay panels allow you to blend the exterior of your	In some cases, your cabinet manufacturer may choose to work
	refrigerator into the overall kitchen décor, and to use custom	with one panel routed for the different dimensions. Follow these
	handles for additional design flexibility.	panel dimension and placement instructions to be sure that the
	NOTE: To use full-overlay custom panels, a Trimless Trim Kit for	custom overlay panels will fit properly.
	Side by Sides is required (TRIMKITSXS). Full-overlay custom	IMPORTANT:
	panels and handles are required but not included. Create the	■ The total weight of the refrigerator door overlay panel cannot
	panels according to these specifications. You may order
		exceed 50 lbs (23 kg).
	Thermador’s Handle Kit (HANDKIT) or select handles from another
		■ The total weight of the freezer door overlay panel cannot
	source. See the “Models” section under “Design Specifications”
	for additional information.	exceed 30 lbs (13.5 kg).

	The custom panels must have backer panels attached in order to					■ The total weight of the top grille overlay panel cannot exceed
	mount them to the refrigerator. It is most common to work with						10 lbs (4.5 kg).
	three panels, as shown in the following graphic: a decorative					To minimize panel weight, you may use 2" (5.08 cm) spacer strips
	overlay panel, a ¹/ " (3.18 mm) spacer panel or spacer strips and a
						around the perimeter in place of full-sheet solid spacer panels.
	¹/ " (6.35 mm) backer panel.
						The spacer strips must be set in at least 1" (2.54 cm) from the top,
	Overlay Panel		Spacer Panel			bottom and sides edges of the backer panel. If you use spacer
						strips, it is also recommended that you use two 2" (5.08 cm) strips
			Spacer Panel
						horizontally centered for added support.
			1/8"		Overlay Panel			Top Grille
			(3.18mm)
								C
					Backer Panel			73/8"
								(18.73 cm)
					1" minimum
					(2.54 cm)		81/2"	F
			Backer Panel		Door/Grille Trim	(21.59 cm)
				Offset Dimension
	5/8" to 3/4"		1/4"
	(15.88 to							Bottom Offset
		1/8"	(6.35 mm)
	19.05 mm)
		(3.18 mm)						1" (2.54 cm)
			Freezer		Freezer Frameless		Freezer
			Framed Dispenser		Dispenser		Non-Dispenser	Refrigerator
			A		A		A	B
			23 ⁄ "	Handle-Side	23 ⁄ "	Handle-Side
				Offset		Offset
			(59.53 cm)	¹⁄ " (3.2 mm)	(59.53 cm)	¹⁄ " (3.2 mm)		Handle-Side
					24"			Offset
			D	(60.96 cm)				¹⁄ " (3.2 mm)
					D
			12 ⁄ "		Bottom Offset		70¹⁄ "	70¹⁄ "
					¹⁄ " (3.2 mm)		(179.07 cm)	(179.07 cm)
			(31.27 cm)
					A
			47³⁄ "	71¹⁄ "				71¹⁄ "
			(119.86 cm)	(180.50 cm)				(180.50 cm)
			D		D		D	E
					34³⁄ "
				(88.27 cm)
			34³⁄ "		34³⁄ "	Handle-Side
						Offset
			(87.3 cm)		(87.3 cm)
						¹⁄ " (3.2 mm)
			Bottom Offset		Bottom Offset		Bottom Offset	Bottom Offset
			¹⁄ " (3.2 mm)		¹⁄ " (3.2 mm)		¹⁄ " (3.2 mm)	¹⁄ " (3.2 mm)

Decorative Overlay Panels

Model	A	B	C
42" (106 cm)	17 ¹⁄"	23 ¹⁄"	41 ³⁄"
	(43.50 cm)	(58.74 cm)	(105.09 cm)
48" (122 cm)	19 ⁄"	26 ⁄"	47 ³⁄"
	(49.85 cm)	(67.63 cm)	(120.33 cm)

Backer Panels

Model		D		E	F
42" (106 cm)	16	¹ ⁄"	22	¹ ⁄"	40 ¹⁄"
	(43.50 cm)		(58.26 cm)		(102.87 cm)
48" (122 cm)	19	⁄"	26	⁄"	46 ¹⁄"
	(49.37 cm)		(67.15 cm)		(118.11 cm)

12

Stainless Steel Series Side Panels

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

■The dimensions shown are actual product dimensions and may not reflect the needed panel installation dimensions.

■The side panel should be a minimum of ½" (1.27 cm) thick to avoid warping.

■If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

Refrigerator

24¹⁄ "

(61.3 cm)

23¹¹⁄ "

(60.3 cm)

23¹⁄ "

(59.7 cm)

Side Trim

¹⁄ " (6.35 mm)

¹¹⁄ " (4.5 mm)

³⁄ " (4.7 mm)

⁄ " (5.5 mm)

¹³⁄ " (10 mm)							⁄ "
							(15.7 mm)

Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall. Add ⁄" (5.6 mm) to this measurement to allow the side panel to fit into the trim.

2.If the panel is more than ¹⁄" (6.35 mm) thick, rout the front edge to allow the side panel to fit into the trim.

A

Flush Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall.

2.Attach the support board with a screw or adhesive that is compatible with aluminum and wood.

A

Recessed Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall.

2.Rout the front edge of the support board or attach a ¹⁄" (6.35 mm) board to hold the panel in the cabinet side trim.

A

13

Custom Panel Series Side Panels

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

■The dimensions shown are actual product dimensions and may not reflect the needed installation dimensions.

■The side panel should be a minimum of ½" (1.27 cm) thick to avoid warping.

■If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on rear wall.

Refrigerator

Overlay

23³⁄ "

(59.40 cm)

Side Trim

³⁄ "

(4.5 mm)

³⁄ " (9.7 mm)

¹⁄ " (1.5 mm)

¹⁄ " (3.2 mm)

Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall. Add ¹⁄ " (0.8 mm) to this measurement to allow the side panel to fit into the trim.

2.If the panel is more than ³⁄ " (9.5 mm) thick, rout the front edge to allow the side panel to fit into the trim.

A

Recessed Inset Installation Dimensions

1.Measure the distance from point A (as shown) to back wall.

2.Rout the front edge of the support board or attach a ³⁄ " (9.5 mm) board to hold the panel in the cabinet side trim.

A

INSTALLATION

REQUIREMENTS

Tools and Parts

IMPORTANT:

■Installer: Leave Installation Instructions with the homeowner.

■Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use.

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■	Cordless drill	■	T27 Torx®† screwdriver
■	Drill bits	■	¹¹⁄ " nut driver
■	Adjustable wrenches (2)	■	³⁄ " and ¹⁄ " open-end wrenches
■	Phillips screwdriver	■	⁄ " Allen wrench
■	Small level	■	⁄ " socket wrench
■	Appliance dolly	■	Tape measure

PARTS NEEDED:

■#8 x 3" (7.6 cm) or longer wood screws (6)

■2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board (1 or 2)

■Make custom or overlay panels or consult a qualified cabinetmaker or carpenter to make the panels. See “Design Specifications.”

■If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄ " (6.35 mm) compression fitting.

†®TORX is a registered trademark of Textron Innovations Inc.

14

Location Requirements

The refrigerator can be recessed in an opening between cabinets	■ A grounded 3 prong electrical outlet should be placed within
or installed at the end of a cabinet run using a side panel to	4" (10.2 cm) of the right side cabinets or end panel. See
enclose the refrigerator.	“Electrical Requirements” for additional information.

■ The water shutoff should be located in the base cabinet on WARNING either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See “Water Supply Requirements” for more information.

Explosion Hazard
Keep flammable materials and vapors, such as		80" - 90"
gasoline, away from refrigerator.
		(203-229 cm)	4"
Failure to do so can result in death, explosion, or fire.
			(10.2 cm)
IMPORTANT:
■ Observe all governing codes and ordinances.
■ It is recommended that you do not install the refrigerator near
an oven, radiator, or other heat source.	83¹⁄ " (212.1 cm) min.
■ Do not install in a location where the temperature will fall	84³⁄ " (215 cm) max.
	to bottom of solid soffit
below 55°F (13°C).
■ Floor must support the refrigerator weight, more than 600 lbs
(272 kg), door panels and contents of the refrigerator.
■ Ceiling height must allow for side tipping radius. See “Tipping			77"
Radius.”			(196 cm)
■ Location should permit door to open fully. See “Door Swing
Dimensions.”		A
■ Location must permit top grille removal. See “Opening
		Width
Dimensions.”		(see chart following)
Opening Dimensions			6"
■ To avoid tipping during use, the solid soffit must be within 1"			(15.2 cm)
(2.5 cm) maximum above the refrigerator. If the solid soffit is
higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
If the anti-tip boards are needed, they must be attached to the
rear wall studs 80" to 90" (203 to 229 cm) above the floor. See
“Install Anti-Tip Boards” for more information.
NOTE: A clearance of ¹⁄ " (1.3 cm) must be maintained above		1"
the top grille in order for the top grille to be removed.	6"	(2.54 cm)	6"
	(15.2 cm)		(15.2 cm)
		24"
		(60.96 cm) min.

						Model	Width A (as shown above)
¹⁄ "						42	41¹⁄ " (105.4 cm) to 41³⁄ " (106.1 cm)
(1.3 cm)						48	47¹⁄ " (120.7 cm) to 47³⁄ " (121.3 cm)

15

	Electrical Requirements		Water Supply Requirements
	WARNING	■ All installations must meet local plumbing code requirements.
		■	The water shutoff should be located in the base cabinet on
			either side of the refrigerator or some other easily accessible
			area. The right-hand side is recommended. The access hole
			through the cabinet must be within ¹⁄ " (12.7 mm) of the rear
			wall.
			NOTE: If the water shutoff valve is in the back wall behind the
			refrigerator, it must be at an angle so that the tube is not
			kinked when the refrigerator is pushed into its final location.
	Electrical Shock Hazard
	Plug into a grounded 3 prong outlet.
	Do not remove ground prong.
	Do not use an adapter.				6"
					(15.2 cm)
	Do not use an extension cord.
	Failure to follow these instructions can result in death,
	fire, or electrical shock.
	Before you move your refrigerator into its final location, it is
	important to make sure you have the proper electrical connection.			1"
	Recommended Grounding Method		6"		6"
				(2.54 cm)
	A 115 Volt, 60 Hz., AC only, 15or 20-amp fused, grounded		2 cm)		(15.2 cm)
	electrical supply is required. It is recommended that a separate			24"
				(60.96 cm) min.
	circuit serving only your refrigerator be provided. Use an outlet
	that cannot be turned off by a switch. Do not use an	■	If the water shutoff valve is not in the cabinets, the plumbing
	extension cord.		for the water line can come through the floor. A ¹⁄ " (12.7 mm)
	IMPORTANT: If this product is connected to a GFCI (Ground Fault		hole for plumbing should be drilled at least 6" (15.2 cm) from
			the right or left hand side cabinet or panel. On the floor, the
	Circuit Interrupter) protected outlet, nuisance tripping of the
			hole should be no more than 1" (2.54 cm) away from the back
	power supply may occur, resulting in loss of cooling. Food quality
			wall. See “Connect the Water Supply.”
	and flavor may be affected. If nuisance tripping has occurred, and
	if the condition of the food appears poor, dispose of it.	■	If additional tubing is needed, use copper tubing and check
	NOTE: Before performing any type of installation, cleaning, or		for leaks. Install the copper tubing only in areas where the
	removing a light bulb, remove the top grille and turn the master		household temperatures will remain above freezing.
	power switch to OFF or disconnect power at the circuit breaker	■	Do not use a piercing-type or ³⁄ " (4.76 mm) saddle valve
	box.
			which reduces water flow and clogs more easily.

	When you are finished, turn ON the master power switch or	NOTE: Your refrigerator dealer has a kit available with a ¹⁄ "
	reconnect power at the circuit breaker box. Then reset the control
		(6.35 mm) saddle-type shutoff valve, a union, and copper
	to the desired setting.
		tubing. Before purchasing, make sure a saddle-type valve
		complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi

(207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill after heavy usage.

■ If your refrigerator has a water filter cartridge, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed, qualified plumber.

16

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

■Do not remove the protective film until the refrigerator is in its operating position.

■All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

■Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating position.

1.Remove and save the literature package and parts bag taped to the refrigerator door. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

2.If necessary, reduce the tipping radius. See “Tipping Radius” for ceiling height requirements or “Reduce Tipping Radius” for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to “Move the Refrigerator into House.”

Reduce Tipping Radius

(if required)

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See “Tipping Radius” in the “Design Specifications” section for more information.

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model	Reduced Tipping Radius
42" (106 cm)	88¹⁄ " (224.8 cm)
48" (122 cm)	89¹⁄ " (226.7 cm)

Custom Panel Series

1.Grasp both ends of the top grille.

2.Push the top grille straight up, then pull straight out. Lay the grille on a soft surface.

B A B

A.Top grille

B.Cabinet side trim

3.Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

Stainless Steel Series

1.Grasp both ends of the top grille. Push the top grille straight up, then pull straight out. Lay the top grille on a soft surface.

B A B

A.Top grille

B.Cabinet side trim

2.Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

Move the Refrigerator into House

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

1.Place an appliance dolly under the left side of the refrigerator as shown. Place the corner posts from the packing materials over the trims and handles as appropriate. Slowly tighten the strap.

17

NOTE: Pass the dolly strap under the handles for the Curved and Professional Series.

2.Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards to wall studs behind refrigerator. Use six

#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1½" (3.8 cm). The board(s) must overlap the compressor cover.

A B

C

2" (5 cm)

2.Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

3.Place top of cardboard carton or plywood under refrigerator. Remove dolly.

4.Do not remove film or cover.

5.If necessary, reassemble the trim and top grille after the dolly has been removed from the refrigerator.

D

A.Center board ¹⁄" (6.35 mm) max. above refrigerator

B.Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C.Attach to studs with six #8 x 3" (7.6 cm) screws

D.Compressor cover

Install Anti-Tip Boards

IMPORTANT:

■To avoid tipping during use, the solid soffit must be within

1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

■It is recommended that board(s) be installed before the refrigerator is installed.

■Board(s) must be long enough to fully cover the width of the compressor cover.

■Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

■During installation, raise the refrigerator up so there is

¹⁄" (6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1.Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

Parts Needed:

■Minimum 7 ft (2.13 m) flexible, codes approved water supply line

Style 1 - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see “Style 2 - Copper Line Connection.”

1. Unplug refrigerator or disconnect power supply.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2.Connect the flexible, codes approved water supply line to the water shutoff valve by threading the provided nut onto the shutoff valve as shown.

NOTE: The shutoff valve shown is in the side cabinet as recommended.

A

B

C

A.Bulb

B.Nut

C.Water tubing

18

3.	Place the end of the tubing into a bucket, and turn shutoff	Connect to Refrigerator
	valve ON.
4.	Check for leaks. Tighten any nuts or connections (including	Parts Supplied:
	connections at the valve) that leak.
Style 2 - Copper Line Connection		■ ¹⁄ " to ¹⁄ " (6.35 mm to 6.35 mm) male-to-male coupling
NOTE: If there is a water supply line that meets the specifications
in “Water Supply Requirements,” proceed to “Connecting to
Refrigerator.” If not, use the following instructions to connect to
the household cold water supply.
1.	Unplug refrigerator or disconnect power.
2.	Turn OFF main water supply. Turn ON nearest faucet long
	enough to clear line of water.
3.	Locate a ½" to 1¹⁄ " (1.25 cm to 3.18 cm) vertical cold water
	pipe near the refrigerator.
	IMPORTANT:
	■ Make sure it is a cold water pipe.
	■ Horizontal pipe will work, but drill on the top side of the		1"
			(2.54 cm)
	pipe, not the bottom. This will help keep water away from	7"
	the drill and keep normal sediment from collecting in the	(17.78 cm)
	valve.

4.Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄ " (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a ¹⁄ " (6.35 mm) hole in the cold water pipe you have selected.

	A
G	B
	C
F E	D
A. Cold water pipe	E. Compression sleeve
B. Pipe clamp	F. Shutoff valve
C. Copper tubing	G. Packing nut

NOTE: The flexible, codes approved water supply line can connect to the supply valve through the floor or through the side cabinets, as indicated by the gray boxes above.

1.Unplug the refrigerator or disconnect power.

2.Connect the 7 ft (2.13 m) flexible codes approved water tube to the water supply valve.

3.Flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear.

4.Tape the 7 ft (2.13 m) flexible codes approved water supply line to the floor, 7" (17.78 cm) from the left side of the refrigerator. Tape along the length of the tubing, which will allow it to pass beneath the refrigerator without interference.

D.Compression nut

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄ " (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.

8.Turn off the shutoff valve on the water pipe. Coil the copper tubing.

9.Connect the flexible, codes approved water supply line to the water shutoff valve by threading the provided nut onto the shutoff valve.

10.Place the end of the tubing into a bucket, and turn shutoff valve ON.

11.Check for leaks around the saddle valve. Tighten any nuts or connections (including connections at the valve) that leak.

NOTE: Allow a minimum of 26" (66.04 cm) of flexible codes approved water supply line to be loose at the front of the refrigerator for connecting to the refrigerator.

5.Connect the 7 ft (2.13 m) flexible codes approved water supply line to the refrigerator.

NOTE: If the main water shutoff valve is behind the refrigerator, a secondary water shutoff valve may be installed in line with the water supply line at the front of the product.

D

C

B

A

F G

E

A. Household water line	E. Bulb
B. Nut (purchased)	F. Nut
C. Ferrule (purchased)	G. Refrigerator water tubing
D. Coupling

6.Turn on the water supply valve and check all connections for leaks.

19

Plug in Refrigerator

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Set control switch at top of cabinet to the OFF position.

2.Plug into a grounded 3 prong outlet.

Move Refrigerator to Final Location

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1.Place top of cardboard carton or plywood under refrigerator. Remove dolly.

2.Do not remove film or cover.

3.Move the refrigerator straight back and evenly into the opening. Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

Lower Leveling Legs

NOTE: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

Use a ⁄" socket wrench to turn the leveling bolts clockwise to lower the 4 leveling legs until refrigerator weight is supported by leveling legs. The rollers should be off the floor. To avoid cabinet damage, do not apply more than 50 inch-pounds (58 cm - kg) of torque to the leveling legs.

A B	A
	B

A.Rear leveling legs

B.Front leveling legs

Install Custom Panels

IMPORTANT: Thermador is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

NOTE: To install full-overlay custom panels, refer to the installation instructions included with the Trimless Trim Kit. See “Design Specifications.”

Door Panels

1.Remove all tape and door bracing from the refrigerator and freezer doors.

2.Remove the screws that attach the handles to the door frame.

3.Slide the decorative door panels into the door frames.

4.If needed, route the door panels or install a filler panel between the doors and the decorative panels. See “Custom Panels.”

A A

A. Panels

20

5.Replace the door handles. Be sure that the top of both door handles are aligned.

6.Remove the skin from the screw covers. Snap the screw covers into the handle trim section.

5.Replace the top grille in the cabinet side trims and pull the panel down slightly to lock it into place.

B A B

A.Top grille

B.Cabinet side trim

Top Grille Panel

1.Grasp both ends of the top grille.

2.Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

B A B

A.Top grille

B.Cabinet side trim

3.Remove one end cap by loosening the nuts and sliding off the end cap.

A
C
B
D
A. Bottom rail	C. End cap
B. Nuts	D. Top rail

4.Slide the custom panel into the top grille channel and reattach the end cap.

A

A. Custom panel

Level Refrigerator

NOTE: Custom or full-overlay door panels must be installed before leveling the refrigerator.

1.Open the doors and place the level on top of the refrigerator frame as shown. Check to see whether the refrigerator is level from left to right.

A

B

B

A.Level to check left to right leveling

B.Level to check front to back leveling

2.Use the leveling bolts to adjust the leveling legs until the refrigerator is level from left to right.

A	A
B	B

A.Rear leveling bolt

B.Front level bolt

3.Place the level(s) on shelf or shelves. Check to see whether the refrigerator is level from front to back.

4.Use the leveling bolts to adjust the leveling legs until the refrigerator is level from front to back.

5.Be sure that all four leveling legs contact the floor and support the full weight of the refrigerator.

6.Make final check to ensure the refrigerator is level.

21