Kitchenaid KBRS36FM, KBRC36FM, KBRO36FM, KBLV36FP, KBLS36FM User Manual

® 36" Bottom Mount Built-in Refrigerator

PRODUCT MODEL NUMBERS

OVERALL DIMENSIONS

KBLC36FM

KBRC36FM

Front view

Side view

Top view

KBLO36FM

KBRO36FM

25³⁄ "

KBLS36FM

KBRS36FM

(64.5 cm)

35¹⁄ " (89.5 cm)

KBLV36FP

KBRV36FP

23¹⁄ "

(59.7 cm)

25

³⁄ "

Electrical: A 115 Volt, 60 Hz., AC only 15or

(64.5

cm)

20amp fused, grounded electrical supply is

required. It is recommended that a separate circuit

serving only your refrigerator be provided. Use an

*83³⁄ "

outlet that cannot be turned off by a switch. Do not

(211.8 cm)

use an extension cord.

A grounded 3 prong electrical outlet should be

*83³⁄ "

placed within 4" (10.2 cm) of the right side cabi-

(211.8 cm)

nets or end panel.

84" (213 cm)

Power Cord

Water Supply: A cold water supply with water

pressure between 30 and 120 psi (207 - 827 kPa)

is required to operate the water dispenser and ice

maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

The water shutoff should be located in the base

cabinet on either side of the refrigerator or some

*3¹⁄ " (9 cm)

other easily accessible area. If the water shutoff

36¹⁄ " (92 cm)

valve is not in the cabinets, the plumbing for the

• The water line attached to the back of the refrigerator is

water line can come through the floor or the back

5 ft (1.5 m) long.

wall.

• Height dimensions are shown with leveling legs extended

IMPORTANT: The pressure of the water supply

¹⁄ " (3 mm) below the rollers.

* When leveling legs are fully extended to 1¹⁄ " (32 mm) below

coming out of a reverse osmosis system going to

rollers, add 1¹⁄ " (29 mm) to the height dimensions.

the water inlet valve of the refrigerator needs to be

between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is con-		CABINET OPENING DIMENSIONS
nected to your cold water supply, the water pres-
sure to the reverse osmosis system needs to be a
minimum of 40 to 60 psi (276 - 414 kPa).
Do not install the refridgerator near an oven, radia-
tor, or other heat source, or in a location where the			80" - 90"
temperature will fall below 55°F (13°C).
			(203-229 cm)	4"
				(10.2 cm)
DOOR SWING DIMENSIONS
		831/2" (212.1 cm) min.
	23"	843/4" (215 cm) max.
		to bottom of solid soffit
	(58 cm)
	51"			77"
	(130 cm)
				(196 cm)
	59"
	(150 cm)		A
			Width
90˚			351/2" (90.2 cm) min.
			353/4" (90.8 cm) max
110˚
130˚				6"
				(15.2 cm)
A solid soffit must be within 1" (2.5 cm)	If the anti-tip boards are needed, they must be
maximum above the refrigerator. If the solid	attached to the rear wall studs 80" to 90" (203
soffit is higher than 1" (2.5 cm) or one is not	to 229 cm) above the floor.
available, then the refrigerator must be	NOTE: A clearance of 1/2" (1.3 cm) must be		1"
braced to prevent tipping during use.		6"	(2.5 cm)	6"
	maintained in front of the refrigerator’s side
		(15.2 cm)		(15.2 cm)
	trim in order for the top grille to be removed.		24"
			(60.9 cm) min.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. 2317873
Instructions packed with product. Specifications subject to change without notice.	12-14-06