KEYENCE CA-MP81 User Manual

DANGER

WARNING

CAUTION

NOTICE

Reference

WARNING

CAUTION

NOTICE

CAUTION

NOTICE

CAUTION

NOTICE

MENU button

DEFAULT button

button

Video input

Input terminal for video signal.

Power input terminal

The input terminal of the 24 VDC (1 A) power supply.

Mounting bracket

Screw

Mounting hook

Mounting bracket

Phillips screwdriver

Panel (Panel thickness):

1.0 to 4.0 mm

NOTICE

5.8 mm or smaller

Circular connector

96M11412

COLOR LCD MONITOR

CA-MP81

Instruction Manual

Read this manual before use. Keep this manual in a safe place for future reference.

Introduction

 Symbols

This manual uses the following symbols so that you can recognize important messages at a glance. Please read it in its entirety.

It indicates a hazardous situation which, if not avoided, will result in death or serious injury.

It indicates a hazardous situation which, if not avoided, could result in death or serious injury.

It indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

It indicates a situation which, if not avoided, could result in product damage as well as property damage.

It indicates tips for better understanding or useful information.

Safety Information for the CA-MP81

 Installation Location

When installing the CA-MP81, make sure to avoid locations with the following conditions.

• Locations where the CA-MP81 is exposed to direct sunlight

• Locations where the ambient temperature exceeds t he range of 0 to +40°C (32 to 104°C), or where the temperature changes dramatically

• Locations with poor ventilation

• Locations where the relative humidity exceeds the range of 35 to 85%, or condensation occurs

• Locations where corrosive or flammable gas exists

• Locations where a large amount of dust, salt, or ferrous powder exists

• Locations where water, oil, or chemicals may splash onto the CA-MP81

• Locations where the CA-MP81 is subjected directly to vibration or impact

• Locations where radiation noise and static electricity may affect operation of the CA-MP81

• Locate the CA-MP81 and cables as far as possible from high-voltage lines and power lines. Otherwise, generated noise may cause product malfunction or equipment failure

 Handling

• Do not disassemble or modify the CA-MP81, as this may cause fire, electric shock, or equipment failure.

•

Turn the power off immediately if one of the following conditions occur. Continuous use under abnormal conditions may cause fire, electric shock, or equipment failure. Please contact your nearest KEYENCE office for repairs.

- When liquid or a foreign material (such as water, oil, or chemical)

enters the product

- When a strong shock is applied to the product or its housing is

damaged

- When you notice smoke, an unusual smell, or noise coming from

the product CE

• Make sure to turn off power to the CA-MP81 and any connected devices before connecting or disconnecting the cables. Otherwise, the CA-MP81 and connected devices may become damaged.

• If a large amount of dir t or dust accumulates on the CA-MP81, remove it using a tightly squeezed cloth moistened with a dilute solution of neutral detergent. Wipe the unit with a soft, dry cloth. Do not wipe the CA-MP81 with a damp cloth or a cloth moistened with benzine, thinner, or alcohol, as this may cause discoloration or deformation of the unit.

Part Names and Usage

 General Precautions

• Do not use this product for the purpose of protecting a human body or a part of a human body.

• This product is not intended for use as explosion-proof product. Do not use this product in a hazardous location and/or potentially explosive atmosphere.

• When beginning or during operation, ensure that the par ts and functions are operating correctly.

• In the unlikely event of malfunction, ensure that the proper safety equipment is in place to prevent damage to other equipment.

• Please be aware that the functions and performance of the CA-MP81 will not be guaranteed when the product is disassembled or modified, or if used in any way other than described in the specifications.

• When the CA-MP81 is used in combination with other instruments, its functions and performance may be degraded to an unsatisfactory level. Make sure to examine its performance before starting the operation.

Precautions on Regulations and Standards

 CE Marking

Keyence Corporation has confirmed that this product complies with the essential requirements of the applicable EC Directive, based on the following spec ifications. Be sure to consider the following specifications when using this product in the Member State of European Union.

z EMC Directive (2004/108/EC)

• Applicable standard EMI: EN61326-1, ClassA

• The length of cable connected to the power input terminal must be less than 30 m.

Remarks: These specifications do not give any guarantee that the end-product with this product incorporated complies with the essential requirements of EMC Directive. The manufacturer of the end-product is solely responsible for the compliance on the end-product itself according to EMC Directive.

Checking the Package Contents

The CA-MP81 package includes the following parts and equipment. Verify that all parts and equipment are included in the package.

 Color LCD monitor CA-MP81 .........................................1

 Instruction Manual (This manual) ...................................1

 Panel mounting brackets ................................................4

* We have thoroughly inspected the package contents before shipment.

However, in the event of defective or missing items, please contact your nearest KEYENCE sales office.

Hints on Correct Use

 Power supply

Do not use the CA-MP81 with a voltage other than 24 VDC, as this may cause fire, electric shock, or equipment failure.

When using a switching regulator, make sure to ground the frame GND terminal or GND terminal of the power supply. In addition, it is recommended that the CA-MP81 be operated singly from a power source.

EMS: EN61326-1

Installation Procedure

1. Insert the CA-MP81 into the panel.

Secure the mounting bracket to the mounting hooks 4 on the top and bottom surfaces of the CA-MP81 or to the side of the CA-MP81. Tighten the screws using a Phillips screwdriver.

• Tightening the mounting bracket with excessive force may deform the casing. The proper tightening torque for achieving the drip-proof feature is 0.3 N·m. However, note that a drip-proof effect may not be obtained depending on the strength or shape of the panel.

• When installing the CA-MP81, make sure to leave a minimum clearance of 20 mm around the product.

In addition to the panel mounting, the CA-MP81 can be installed by using a mounting stand for a color LCD monitor (sold separately, OP-42278) or a pole-mounting bracket for a color LCD monitor (sold separately, OP-42279). For details, please contact your nearest KEYENCE sales office.

Connecting the 24 VDC Power Source

• Use electrical wiring AWG14 to AWG22.

• Make sure to connect the frame ground terminal for the 24 VDC power source to a type D ground.

• The sizes of solderless connectors are shown below. Use connectors that fit M3 screws.

• Tighten the screws with a torque of 0.5 to 0.75 Nm.

Y connector

5.8 mm or smaller

11412E 1015-2 96M11412 Printed in Japan

Adjustment Procedure

Reference

DEFAULT

Reference

If your monitor needs adjustment due to ambient light, the installation angle, or the characteristics of the connected device, follow the procedure below.

When no video signal is input, a blue screen (with message "NO SYNC SIGNAL" for the first five minutes) is displayed instead of the setting menu.

1. Press the button on the rear of the monitor. The setting menu is displayed.

2. Press the button to move the cursor onto the item to change the setting.

3. Press the button to change the setting of the item.

4. Press the button to change the value/setting.

5. Press the button to return to the status of step 1.

6. When you complete the adjustment, press the button to exit the setting menu.

Auto-escape function

If no button is pressed for about 10 seconds, the setting menu display is turned off. When this occurs, the change(s) made so far will be saved.

The name of the item being selected is displayed.

Item Setting

BRIGHTNESS

CONTRAST

COLOR MODE

sRGB

BLACK LEVEL

POSITION Adjusts the horizontal/vertical position of the screen.

CLOCK

FOCUS

EXIT

Adjusts the brightness of the backlight of the LCD panel. (Only BRIGHTNESS can be adjusted directly with the button.)

Adjusts the contrast of the image. (Adjustable only when the sRGB mode is set to off.)

Adjusts the color tone of RGB individually. (Adjustable only when the sRGB mode is set to off.)

Switches the sRGB mode between on and off. The initial setting is off.

Adjusts the black level. (Adjustable only when the sRGB mode is set to off.)

Adjusts the horizontal size of the screen by adjusting the

clock.

Reduces blurred characters and images by adjusting the

focus.

Sets the other items.

BUTTON LOCK:

when the button is pressed for 3 seconds or more.

Disables all key operations. The lock is released

INFORMATION Displays the device setting information, etc.

RECALL Resets the settings to the factory default (initial) settings.

*1 AUTO ADJUSTMENT function

Pressing the button adjusts the settings automatically to optimum values for the video signals being input. Target items: POSITION, CLOCK, FOCUS (This function activates automatically when video signals are input for the first time after the purchase.)

DEFAULT

Specifications

Product name LCD color monitor

Model CA-MP81

Display element a-Si, TFT active matrix method

Display panel

Backlight Operating life

Input

Power-supply voltage 24 VDC ±10%

Current consumption 1A max.

Ambient temperature 0 to +40°C (32 to 104°F)

Relative humidity 35 to 85%

Construction

Weigh t Approx. 1200 g

Display color 262,144

No. of dots 800 (W) x 600 (H) dots

Active display area

Input signal

Input signal mode

170.4 (W) x 127.8 (H) mm

Approx. 50,000 hours (average) (When installed in an upright position under 25°C (77°F)) Analog RGB signal (0.7 Vp-p, 75 Ω), Horizontal/vertical synchronization signal

800 (W) x 600 (H), Vertical frequency: 60 Hz

Connector High-density D-sub 15-pin female (3-way, inch screw)

Panel-mount type Only the front face is dust-proof an d splashproof equivalent to IP65

The TFT LCD panels may have bright dots that always illuminate and dark dots that never illuminate. This is inevitable due to the manufacturing process and is not a product failure.

Dimensions

LCD color monitor CA-MP81

(Dimension of mounting

bracket)

191.2

180

display area)

127.8

(Active

(Active display area)

(Dimension of

mounting bracket)

Panel cutout

169.5

219.5

241.2

230 151

156

170.4

Panel thickness:

1.0 to 4.0 mm

52.5

77.5

76.2

31.5 135

Mounting bracket Mounting screw

106

255

205

+1 0

171

4-ø6

Unit: mm

4 x M4

(Depth: 5.6 mm)

24.3

93.5

* When OP-66842 is connected

Warranties and Disclaimers

(1) KEYENCE warrants th e Products to be free of defects in materials and workmanship for a

period of one (1) year from the date of shipment. If any models or samples were shown to Buyer, such models or samples were used merely to illustrate the general type and quality of the Products and not to represent that the Products would necessarily conform to said models or samples. Any Products found to be defective must be shipped to KEYENCE with all shipping costs paid by Buyer or offered to KEYENCE for inspection and examination. Upon examination by KEYENCE, KEYENCE, at its sole option, will refund the purchase price of, or repair or replace at no charge any Products found to be defective. This warranty does not apply to any defects resulting from any action of Buyer, including but not limited to improper installation, improper interfacing, improper repair, unauthorized modification, misapplication and mishandling, such as exposur e to excessive current, heat, coldness, moisture, vibration or outdoors air. Components which wear are not warranted.

(2) KEYENCE is pleased to offer suggestions on the use of its various Products. They are

only suggestions, and it is Buyer's responsibility to ascertain the fitness of the Products for Buyer’s intended use. KEYENCE will not be responsible for any damages that may result from the use of the Products.

(3) The Products and any samples ("Products/Samples") supplied to Buyer are not to be

used internally in humans, for human transportation, as safety devices or fail-safe systems, unless their written specifications state otherwise. Should any Products/ Samples be used in such a manner or misused in any way, KEYENCE assumes no responsibility, and additionally Buyer will indemnify KEYENCE and hold KEYENCE harmless from any liability or damage whatsoever arising out of any misuse of the Products/Samples.

(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE PROVIDED

WITH NO OTHER WARRANTIES WHATSOEVER. ALL EXPRESS, IMPLIED, AND STATUTORY WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED. IN NO EVENT SHALL KEYENCE AND ITS AFFILIATED ENTITIES BE LIABLE TO ANY PERSON OR ENTITY FOR ANY DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, ANY DAMAGES RESULTING FROM LOSS OF USE, BUSINESS INTERRUPTION, LOSS OF INFORMATION, LOSS OR INACCURACY OF DATA, LOSS OF PROFITS, LOSS OF SAVINGS, THE COST OF PROCUREMENT OF SUBSTITUTED GOODS, SERVICES OR TECHNOLOGIES, OR FOR ANY MATTER ARISING OUT OF OR IN CONNECTION WITH THE USE OR INABILITY TO USE THE PRODUCTS, EVEN IF KEYENCE OR ONE OF ITS AFFILIATED ENTITIES WAS ADVISED OF A POSSIBLE THIRD PARTY’S CLAIM FOR DAMAGES OR ANY OTHER CLAIM AGAINST BUYER.

In some jurisdictions, some of the foregoing warranty disclaimers or damage limitations may not apply.

BUYER'S TRANSFER OBLIGATIONS:

If the Products/Samples purchased by Buyer are to be resold or delivered to a third party, Buyer must provide such third party with a copy of this document, all specifications, manuals, catalogs, leaflets and written information provided to Buyer pertaining to the Products/Samples.

E 1101-3