Kenwood KDC-X5200BTM Instruction Manual

KDC-X5200BTM

CD-RECEIVER

INSTRUCTION MANUAL

CONTENTS

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

RADIO 6

AUX 7

CD/USB/iPod/ANDROID 8

Spotify 11

BLUETOOTH® 12

AUDIO SETTINGS 20

DISPLAY SETTINGS 24

TROUBLESHOOTING 25

REFERENCES 27

Maintenance More information

INSTALLATION/ CONNECTION 29

SPECIFICATIONS 32

BEFORE USE

IMPORTANT

•

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe

Warning and Caution in this manual.

•

Please keep the manual in a safe and accessible place for future reference.

WARNING

• Do not operate any function that takes your attention away from safe driving.

• Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•

Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•

Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•

Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

•

If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

•

USB rating for the USB cable from the rear of the unit is indicated on a label.

•

Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected

( 31)

. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

Remote control (RC-406):

•

Do not leave the remote control in hot places such as on the dashboard.

•

The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•

The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

How to read this manual

•

Operations are explained mainly using buttons on the faceplate.

•

English indications are used for the purpose of explanation. You can select the display language from the

• [XX]

indicates the selected items.

• ( XX)

indicates references are available on the stated page.

( 32)

[FUNCTION]

menu.

( 5)

ENGLISH

BASICS

Faceplate

Lights up when

Volume

knob

Detach button

Note: The highlighted area on the faceplate flashes when the unit enters searching status.

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob. Press

Select a source

Change the display information Press DISP repeatedly.

Display

window

Bluetooth connection is established.

Auxiliary cable from the rear of the unit.

USB cable from the rear of the unit.

Press

• Press and hold to turn off the power.

Press

( 13)

repeatedly.

Attach

Detach

How to reset

Reset the unit within 5seconds after detaching the faceplate.

( 29)

Remote control (RC-406)

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

or .

• Press and hold volume to 15.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( Not available )

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

to continuously increase the

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power for the first time (or

[FACTORY RESET]

“PRESS” “VOLUME KNOB”

1 Turn the volume knob to select

[TU]

(Turkish) or

[ENG]

Then, the display shows: “CANCEL DEMO”

KNOB”.

2 Press the volume knob.

[YES]

is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Then, the display shows the selected crossover type: “2-WAY X ’ OVER” or “3-WAY X ’ OVER”

• To change the crossover type, see “Change the crossover type”. (

is set to

[YES], 5

), the display shows: “SEL LANGUAGE”

[SP]

is selected for the initial setup.

(Spanish), then press the knob.

[EN]

(English),

[RU]

“PRESS” “VOLUME

(Russian),

Set the clock and date

Press the volume knob to enter

2 Turn the volume knob to select

To adjust the clock

3 Turn the volume knob to select

[FUNCTION] [CLOCK]

[CLOCK ADJUST]

, then press the knob.

4 Turn the volume knob to make the settings, then press the knob.

Hour

5 Turn the volume knob to select 6 Turn the volume knob to select

To set the date

7 Turn the volume knob to select 8 Turn the volume knob to select

9 Turn the volume knob to select

the knob.

Minute

[CLOCK FORMAT] [12H]

[24H]

[DATE FORMAT] [DD/MM/YY]

[DATE SET]

, then press the knob.

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press .

Set the initial settings

Press repeatedly to enter STANDBY.

2 Press the volume knob to enter 3 Turn the volume knob to select an item (

5)

knob.

[FUNCTION]

), then press the

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

, then press the knob.

[MM/DD/YY]

, then press

ENGLISH

GETTING STARTED

DISPLAY

EASY MENU

TUNER SETTING

PRESET TYPE

SYSTEM

KEY BEEP

SOURCE SELECT

SPOTIFY SRC

BUILT-IN AUX

POWER OFF WAIT

CD READ 1

When entering

: LCD DISPLAY zone illumination changes to white color. ;

OFF

: LCD DISPLAY zone illumination remains as

SELECT]

•

KEY zone illumination changes to light blue color when you

enter

•

Refer to the illustration on page 24 for zone identification.

NORMAL

band (FM1/FM2/FM3/MW).; each preset button, regardless of the selected band.

(Not applicable if 3-way crossover is selected.)

:Activates the keypress tone.;

:Enables SPOTIFY in source selection.;

( 11)

:Enables AUX in source selection.;

Applicable only when the demonstration mode is turned off. Sets the duration when the unit will automatically turn off (while in standby mode) to save the battery.

20M

: 20minutes;

– – –

:Cancels

:Automatically distinguishes between audio file disc and music

CD.;

:Forces to play as a music CD. No sound can be heard if an

audio file disc is played.

Default:

[FUNCTION]

color.

( 24)

[FUNCTION]

:Memorizes one station for each preset button in each

...

, irregardless of the

MIX

40M

: 40minutes;

[COLOR

[EASY MENU]

:Memorizes one station for

OFF

:Deactivates.

OFF

:Disables.

60M

: 60minutes;

setting.

:Disables.

( 7)

F/W UPDATE

UPDATE SYSTEM

F/W UPDATE xxxx

FACTORY RESET YES

CLOCK

CLOCK DISPLAY

ENGLISH

РУССКИЙ

TURKCE

ESPANOL

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated).

For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.

:Resets the settings to default (except the stored station).; NO:Cancels.

:The clock time is shown on the display even when the unit is turned off.;

OFF

:Cancels.

Select the display language for applicable. By default,

[ENGLISH]

is selected.

[FUNCTION]

menu and music information if

Change the crossover type

Press repeatedly to enter STANDBY.

2 Press and hold number buttons 4 and 5 to enter crossover select.

The current crossover type appears.

3 Turn the volume knob to select “2WAY” or “3WAY”, then press the knob. 4 Turn the volume knob to select “YES” or “NO”, then press the knob.

The selected crossover type appears.

• To cancel, press and hold

• To adjust the selected crossover settings,

( 21, 22)

Caution

Select a crossover type according to how the speakers are connected.

( 31, 32)

If you select a wrong type:

• The speakers may damage.

• The output sound level may be extremely high or low.

ENGLISH

RADIO

Search for a station

Press repeatedly to select RADIO.

2 Press repeatedly (or press / on the remote

control) to select FM1/FM2/FM3/MW.

3 Press S/T (or press S/ on the remote control) to

search for a station.

• To change the searching method for S/T: Press

repeatedly. AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or

press one of the number buttons (1to6) on the remote control).

Direct Access Tuning

(using the remote control)

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press

• If no operation is done for 10seconds after step

is automatically canceled.

or DIRECT.

2, Direct Access Tuning

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

TUNER SETTING

LOCAL SEEK

AUTO MEMORY

MONO SET

NEWS SET ON

REGIONAL ON

AF SET ON

TI ON

: Searches only stations with good reception. ;

•

Settings made are applicable only to the selected source/station. Once

you change the source/station, you need to make the settings again.

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

: The unit will temporarily switch to News Programme if available. ;

OFF

:Cancels.

: Switches to another station only in the specific region using the “AF”

control.;

: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor.;

:Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up).;

OFF

:Cancels.

OFF

[NORMAL]

:Cancels.

is selected for

OFF

: Cancels.

[PRESET TYPE]. ( 5)

:Cancels.

ENGLISH

RADIO

PTY SEARCH1 Turn the volume knob to select the available Program Type, then press

CLOCK

TIME SYNC

the knob.

Turn the volume knob to select the PTY language (

GERMAN

ON OFF

), then press the knob.

Press S/T to start searching.

:Synchronizes the unit’s time to the Radio Data System station time.;

:Cancels.

ENGLISH/FRENCH

AUX

Preparation:

Select

[ON]

for

[BUILT-IN AUX]

Start listening

Connect a portable audio player (commercially available).

for

[SOURCE SELECT]. ( 5)

3.5mm stereo mini plug with “L” shaped connector (commercially available)

Available Program Type for

SPEECH : NEWS, AFFAIRS, INFO

CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT

MUSIC

POP M

(music),

CLASSICS, OTHER M OLDIES, FOLK M

The unit will search for the Program Type categorized under

[MUSIC]

if selected.

[LOCAL SEEK]/[MONO SET]/[NEWS SET]/[REGIONAL]/[AF SET]/[TI]/[PTY SEARCH]

• selectable only when the band is FM1/FM2/FM3.

• If the volume is adjusted during reception of traffic information or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information or news bulletin is turned on.

[PTY SEARCH]

(information),

ROCK M

(music),

(music)

SPORT, EDUCATE, DRAMA

EASY M

JAZZ, COUNTRY, NATION M

(music),

LIGHT M

(music),

[SPEECH]

Portable audio player

Auxiliary cable from the rear of the unit.

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter 2 Turn the volume knob to select 3 Turn the volume knob to select

[FUNCTION] [SYSTEM] [AUX NAME SET]

, then press the knob.

4 Turn the volume knob to select an item, then press the knob.

AUX

(default)/

DVD/PORTABLE/GAME/VIDEO/TV

5 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH

CD/USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

USB cable from the rear of the unit (USB input terminal).

ENGLISH

Label side

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102/KCA-iP103 (optional accessory) or accessory of the iPod/ iPhone

ANDROID

USB cable (commercially available)

Eject disc

To On the faceplate On the remote control

Playback/pause Press .

Reverse/Fast-forward

Select a track/file

Select a folder

Repeat play

Press and hold S/T.

Press S/T.

Press J/K.

Press repeatedly.

TRACK REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/ALL REPEAT

Press

Press and hold S/

Press S/

Press

/ .

: Audio CD

: MP3/WMA/AAC/WAV/

FLAC file

FILE REPEAT/FOLDER REPEAT/REPEAT OFF

Random play

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the

Press repeatedly.

DISC RANDOM/RANDOM OFF

: Audio CD

FOLDER RANDOM/RANDOM OFF

Press and hold

to select

: iPod or ANDROID

: MP3/WMA/AAC/WAV/FLAC file,

iPod or ANDROID

ALL RANDOM

instructions to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

For ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files.

[BROWSE MODE]

is selected.

[MODE OFF]/[BROWSE MODE]

( 9)

is selected.

( 9)

CD/USB/iPod/ANDROID

Select control mode

While in iPod USB source, press 5 repeatedly.

MODE ON

: Control iPod using the iPod itself. However, you can still play/

MODE OFF

While in ANDROID source, press 5 repeatedly.

BROWSE MODE

HAND MODE

Select music drive

While in USB source, press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage

• Selected drive of a multiple drives device.

Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Select a file from a folder/list

For iPod/ANDROID, applicable only when selected.

pause, file skip, fast-forward or reverse from this unit.

: Control iPod from this unit.

: Control Android device from this unit via KENWOOD

MUSIC PLAY application installed in the Android device.

: Control Android device using the Android device itself via

other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

Class).

[MODE OFF]/[BROWSE MODE]

1 Press . 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Skip Search

Press S/T to search at a preset skip search ratio.

( 10, [SKIP SEARCH])

• Pressing and holding S/T searches at a 10% ratio.

Alphabet search

You can search for a file according to the first character.

For iPod USB source

(applicable only for CD, USB and ANDROID source)

(applicable only for iPod USB and ANDROID source)

1 Turn the volume knob quickly to enter character search. 2 Turn the volume knob to select the character.

• Select “ 3 Press S/T to move to the entry position.

” to search for a character other than AtoZ, 0to9.

• You can enter up to 3characters. 4 Press the volume knob to start searching.

For ANDROID source

1 Press J/K to enter character search. 2 Turn the volume knob to select the character.

^A^: Upper case letters (A to Z) _A_: Lower case letters (a to z)

-0-: Numbers (0 to 9) : Character other than AtoZ, 0to9

***

3 Press the volume knob to start searching.

• To return to the root folder/first file/top menu, press 5.

BT AUDIO source.)

• To return to the previous setting item, press .

• To cancel, press and hold

(Not applicable for

ENGLISH

CD/USB/iPod/ANDROID

Direct Music Search

(using the remote control)

1 Press DIRECT. 2 Press the number buttons to enter a track/file number. 3 Press to search for music.

• To cancel, press or DIRECT.

• Not available if Random Play is selected.

• Not applicable for iPodUSB and ANDROID source.

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via USB input terminal).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

You can make the settings in the same way as connection via Bluetooth.

( 18)

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default:

USB

MUSIC DRIVE DRIVE CHANGE

automatically and playback starts. Repeat steps

SKIP SEARCH 0.5%/1%/5%/10%

the skip search ratio over the total files.

:The next drive (

to 3 to select the following drives.

[DRIVE 1]

[DRIVE 4]

: While listening to iPod USB or ANDROID source, selects

) is selected

ENGLISH

Spotify

Preparation:

Install the latest version of the Spotify application on your device (iPhone/ iPod touch), then create an account and log in to Spotify.

• Select

[ON]

for

[SPOTIFY SRC]

Start listening

Open the Spotify application on your device.

2 Connect your device to the USB input terminal.

[SOURCE SELECT]. ( 5)

KCA-iP102/KCA-iP103 (optional accessory) accessory of the iPod/iPhone

To On the faceplate On the remote control

Repeat play

Press repeatedly.

REPEAT ALL/REPEAT ONE

( Not available )

REPEAT OFF

Random play

Press repeatedly.

SHUFFLE ON/SHUFFLE OFF

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

This feature is available for tracks in Radio only. If thumbs down is selected, the current track is skipped.

Available for premium account users only.

Available for tracks in Playlists only.

( Not available )

USB cable from the rear of the unit.

3 Press repeatedly to select SPOTIFY.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback/pause

Skip a track

Thumbs up or thumbs

down

Press

Press S

Press J/K.

. Press

/ T. Press S

Press

/ .

Start radio Press and hold 5. ( Not available )

Save favorite song information

While listening to the Radio on Spotify...

Press and hold the volume knob.

“SAVED” appears and the information is stored to “Your Music” or “Your Library” on your Spotify account.

To unsave, repeat the same procedure.

“REMOVED” appears and the information is removed from “Your Music” or “Your Library” on your Spotify account.

ENGLISH

Spotify

Search for a song or station

Press .

2 Turn the volume knob to select a list type, then press the knob.

The list types displayed differ depending on the information sent

from Spotify.

3 Turn the volume knob (or press J/K on the remote control) to

select the desired song or station.

4 Press the volume knob (or press on the remote control) to

confirm.

You can browse through the list quickly by turning the volume knob

quickly.

To cancel, press and hold

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

– Sub Band Codec (SBC) – Advanced Audio Coding (AAC)

Connect the microphone

Rear panel

Microphone input jack

Adjust the microphone angle

Secure using cord clamps (not supplied) if necessary.

Microphone (supplied)

ENGLISH

BLUETOOTH®

Pair and connect a Bluetooth device for the first time

Press to turn on the unit.

2 Search and select this unit model name (KDC-X5***BTM) on the

Bluetooth device.

“PAIRING”

KNOB” appears on the display.

“PASS XXXXXX” Device name “PRESS” “VOLUME

• For some Bluetooth devices, you may need to enter the Personal

Identification Number (PIN) code immediately after searching.

3 Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed.

Once pairing is completed, Bluetooth connection is established automatically.

• “BT1” and/or “BT2” indicator on the faceplate lights up.

• This unit supports Secure Simple Pairing (SSP).

• Up to five devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,

• A maximum of two Bluetooth phones and one Bluetooth audio device

17, [DEVICE DELETE]

can be connected at any time. However, while in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

• Refer to the instruction manual of the Bluetooth device for more information.

( 18)

Auto Pairing

When you connect iPhone/iPod touch/Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if: – Bluetooth function of the connected device is turned on. –

[AUTO PAIRING]

– KENWOOD MUSIC PLAY application is installed on the Android device

( 8)

and

[BROWSE MODE]

is set to

[ON]. ( 17)

is selected.

( 9)

ENGLISH

BLUETOOTH®

BLUETOOTH — Mobile phone

KEY

Receive a call

When there is an incoming call:

• The KEY zone illuminates in green color and flashes.

• The unit answers the call automatically if selected time.

During a call:

• The LCD DISPLAY zone illuminates according to the settings made for

[DISPLAY] ( 24)

• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

To On the faceplate On the remote control

First incoming call...

Answer a call

Reject a call

End a call

( 15)

and the KEY zone illuminates in green color.

Press volume knob or one of the number buttons (1 to 6).

Press

or the

[AUTO ANSWER]

Press

is set to a

To On the faceplate On the remote control

While talking on the first incoming call...

Answer another incoming call and hold the current call

Reject another incoming call

While having two active calls...

End current call and activate held call

Swap between the current call and held call

Adjust the phone volume

[00]

[35]

(Default:

[15]

)

Switch between hands-free and private talk modes

Press

. Press .

Press

Turn the volume knob during a call.

• This adjustment will not affect the volume of the other sources.

Press a call.

• Operations may vary according to the connected Bluetooth device.

. Press .

during

Press

Press or

( Not available )

ENGLISH

BLUETOOTH®

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter 2 Turn the volume knob to select an item (see the following

table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

MIC GAIN LEVEL –10

NR LEVEL LEVEL –5

ECHO CANCEL LEVEL –5

to

microphone increases as the number increased.

to level until the least noise is being heard during a phone conversation.

delay time until the least echo is being heard during a phone conversation.

LEVEL +5(LEVEL 0

to

LEVEL +5(LEVEL 0

Make the settings for receiving a call

Press to enter Bluetooth mode.

1 2 Turn the volume knob to select an item (see the following

table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

[FUNCTION]

LEVEL +10(LEVEL –4

):Adjust the noise reduction

):Adjust the echo cancellation

Default:

):The sensitivity of the

SETTINGS

AUTO ANSWER

BATTERY/SIGNAL* AUTO

Functionality depends on the type of the phone used.

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

to30:The unit answers incoming call automatically in the selected time (in

seconds).;

OFF

:Cancels.

:Shows the strength of the battery and signal when the unit detects a

Bluetooth device and the Bluetooth device is connected.;

OFF

1 Press to enter Bluetooth mode.

“(First device name)” appears.

• If two Bluetooth phones are connected, press again to switch to

another phone.

“(Second device name)” appears. 2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY

(Applicable only if the phone supports PBAP.)

Press the volume knob to select a name or a phone number.

• “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the display to indicate the previous call status.

• Press

DISP

• “NO DATA” appears if there is no recorded call history.

Press the volume knob to call.

to change the display category (NUMBER or NAME).

Default:

:Cancels.

ENGLISH

BLUETOOTH®

PHONE BOOK

NUMBER DIAL

VOICE

BATTERY LVL LOW

NO SIGNAL/SIGNAL LVL LOW/MID/MAX*:Shows the strength of the current received signal.

Functionality depends on the type of the phone used.

(Applicable only if the phone supports PBAP.)

Turn the volume knob quickly to enter alphabet search mode (if the

phonebook contains many contacts).

The first menu (ABCDEFGHIJKLMN) appears.

• To go to the other menu (OPQRSTUVWXYZ1

• To select the desired first letter, turn the volume knob or press

S/T

Select “1” to search with numbers and select “

symbols.

Turn the volume knob to select a name, then press the knob.

Turn the volume knob to select a phone number, then press the knob

to call.

•

The phonebook of the connected phone is automatically transferred to

the unit when pairing.

•

Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL.

•

This unit can display only non-accent letters. (Accent letters such as “Ú”

is shown as “U”.)

Turn the volume knob to select a number (0 to 9) or character

(

, #, +).

Press

Repeat steps

Press the volume knob to call.

(or using the remote control)

Press the number buttons (0 to 9) to enter the phone number.

Press to call.

Speak the name of the contact you want to call or the voice command to control the phone functions.

MID/FULL*:Shows the strength of the battery.

, then press the knob.

S/T

to move the entry position.

and 2 until you finish entering the phone number.

( Make a call using voice recognition)

), press

” to search with

J / K

Make a call using voice recognition

Press and hold to activate the voice recognition of the

connected phone.

2 Speak the name of the contact you want to call or the voice

command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select

[NUMBER DIAL]

, then press the knob.

[CALL HISTORY], [PHONE BOOK]

, or

3 Turn the volume knob to select a contact or enter a phone number.

If a contact is selected, press the volume knob to show the phone

number.

4 Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored. To erase a contact from the preset memory, select

and store a blank number.

[NUMBER DIAL]

in step 2

Make a call from memory

Press to enter Bluetooth mode.

1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

ENGLISH

BLUETOOTH®

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

BT MODE

PHONE SELECT

AUDIO SELECT

DEVICE DELETE

PIN CODE EDIT (0000)

RECONNECT ON

AUTO PAIRING ON

INITIALIZE YES

Selects the phone or audio device to connect or disconnect. “

” appears in front of the device name when connected.

“

” appears in front of the current playback audio device.

•

You can only connect a maximum of two Bluetooth phones and one

Bluetooth audio device at any time.

Turn the volume knob to select a device to delete, then press the knob.

Turn the volume knob to select

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press S/T to move the entry position.

Repeat steps

Press the volume knob to confirm.

:The unit automatically reconnect when the last connected Bluetooth

device is within range.;

:The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;

:Initializes all the Bluetooth settings (including stored pairing,

phonebook, and etc.).;

and 2 until you finish entering the PIN code.

OFF

:Cancels.

OFF

:Cancels.

[YES]

:Cancels.

[NO]

, then press the knob.

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000” appears.

2 Search and select this unit model name (KDC-X5***BTM) on the

Bluetooth device.

3 Operate the Bluetooth device to confirm pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after the test.

PAIRING: Pairing status HF CONNECT: Hands-Free Profile (HFP) compatibility AUDIO CONNECT: Advanced Audio Distribution Profile (A2DP)

PHONEBOOK DL: Phonebook Access profile (PBAP) compatibility

To cancel test mode, press and hold

compatibility

to turn off the unit.

ENGLISH

BLUETOOTH®

BLUETOOTH — Audio

While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.

Audio player via Bluetooth

Press repeatedly (or press SRC on the remote control) to select BTAUDIO.

2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback/pause

Select group or folder

Reverse/Forward skip

Reverse/Fast-forward Press and hold

Repeat play Press

Random play Press and hold

Press

Press J / K.

Press S/T. Press S/

S/T.

ALL REPEAT, FILE REPEAT REPEAT OFF

select

• Press

RANDOM OFF

. Press

repeatedly.

ALL RANDOM

to select

Press

Press and hold S/

( Not available )

To On the faceplate On the remote control

Select a file from a folder/list

Switch between connected Bluetooth audio devices

Pressing the “Play” key on the connected device itself also causes switching of sound output

from the device.

Operations and display indications may differ according to their availability on the connected device.

Refer to “Select a file from a folder/list” on page

Press 5.

( Not available )

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

1 Press the volume knob to enter 2 Turn the volume knob to select an item (

knob.

Repeat step 2 until the desired item is selected or activated.

[FUNCTION]

), then press the

4 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH

BLUETOOTH®

REMOTE APP

SELECT

IOS YES

ANDROID YES

ANDROID LIST

STATUS

Displayed only when

Select the device (IOS or ANDROID) to use the application.

via USB input terminal.; If IOS is selected, select iPod BT source (or iPod USB if your iPhone/iPod is connected via USB input terminal) to activate the application.

•

– You change from iPod BT source to any playback source connected via

– You change from iPod USB source to iPod BT source.

* Selects the Android smartphone to use from the list.

Shows the status of the selected device.

IOS CONNECTED

iPod connected via Bluetooth or USB input terminal.

IOS NOT CONNECTED ANDROID CONNECTED

Android smartphone connected via Bluetooth.

ANDROID NOT CONNECTED

application.

Default:

:Selects iPhone/iPod to use the application via Bluetooth or connected

The connectivity of the application will be interrupted or disconnected if:

the USB input terminal.

:Selects Android smartphone to use the application via Bluetooth.;

: Cancels.

[ANDROID]

:Cancels.

: You are able to use the application using the iPhone/

: No IOS device is connected to use the application.

: You are able to use the application using the

: No Android device is connected to use the

[SELECT]

is set to

[YES]

Listen to iPhone/iPod via Bluetooth

You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.

Press

• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB input terminal.

• If you plug in an iPhone/iPod to the USB input terminal while listening to iPodBT source, the source automatically change to iPodUSB. Press

repeatedly to select iPodBT.

( 8)

to select iPodBT if the device is still connected via Bluetooth.

Internet radio via Bluetooth

Listen to Spotify

You can listen to Spotify on the iPhone/iPod/Android device via Bluetooth on this unit.

• Make sure the USB input terminal is not connected to any device.

Preparation:

Select

[ON]

for

[SPOTIFY SRC]

[SOURCE SELECT]. ( 5)

1 Open the Spotify application on your device. 2 Connect your device via Bluetooth connection.

( 13)

3 Press repeatedly to select SPOTIFY (for iPhone/iPod) or

SPOTIFY BT (for Android device).

The source switches and broadcast starts automatically.

•

You can operate Spotify in the same way as Spotify via USB input terminal.

( 11)

ENGLISH

AUDIO SETTINGS

While listening to any source...

1 Press AUDIO to enter 2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

(or using the remote control)

1 Press AUD to enter 2 Press J / K to select an item, then press .

To return to the previous setting item, press

AUDIO CONTROL

SUB-W LEVEL

MANUAL EQ

62.5HZ LEVEL LEVEL LEVEL–9

100 HZ/160 HZ/250 HZ/ 400 HZ/630 HZ/1 KHZ/

1.6KHZ/2.5KHZ/4 KHZ/

6.3KHZ/10 KHZ/16 KHZ LEVEL

Q FACTOR 1.35/1.50/2.00

[AUDIO CONTROL]

LEVEL –50

output level.

The sound elements (frequency level, tone level, Q factor) are preset into each selection.

BASS EXTEND

LEVEL–9

memorize for each source. (Before making an adjustment, select the source you want to adjust.)

directly.

LEVEL +10 (LEVEL 0

the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)

:Turns on the extended bass.;

LEVEL +9 (LEVEL 0

:Adjust the quality factor.

): Adjusts the subwoofer

LEVEL +9 (LEVEL 0

):Adjusts the level to

Default:

):Adjusts

OFF

:Cancels.

PRESET EQ

BASS BOOST

LOUDNESS

SUBWOOFER SET ON

FADER

BALANCE

VOLUME OFFSET

SOUND EFFECT

SOUND RECONSTRA

(Sound reconstruction)

SPACE ENHANCER

SOUND REALIZER LEVEL1/LEVEL2/LEVEL3

STAGE EQ LOW/MIDDLE/HIGH

DRIVE EQ ON

NATURAL/ROCK/POPS/EASY/TOP40/JAZZ/POWERFUL/USER

Selects a preset equalizer suitable to the music genre. (Select use the settings made in

LEVEL1/LEVEL2/LEVEL3/LEVEL4/LEVEL5

boost level.;

LEVEL1/LEVEL2

to produce a well-balanced sound at a low volume level.;

:Turns on the subwoofer output.;

(Not applicable if 3-way crossover is selected.)

REAR 15

balance.

LEFT 15

balance.

LEVEL –15

each source. (Before adjustment, select the source you want to adjust.)

(Not applicable for RADIO source and AUX source.)

:Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression.;

(Not applicable for RADIO source.)

SMALL/MEDIUM/LARGE OFF

OFF

the speakers.;

: Boosts the frequency to reduce the noise heard from outside the car or running noise of the tyres.;

:Cancels.

[MANUAL EQ]

OFF

:Cancels.

:Selects your preferred low and high frequencies boost

FRONT15 (0

RIGHT15 (0

):Adjusts the rear and front speaker output

):Adjusts the left and right speaker output

LEVEL +6 (LEVEL 0

:Virtually enhances the sound space.;

:Virtually makes the sound more realistic.;

:Virtually adjust the sound position heard from

OFF

:Cancels.

:Selects your preferred bass

OFF

:Cancels.

):Preset the initial volume level of

OFF

:Cancels.

OFF

:Cancels.

OFF

[USER]

:Cancels.

ENGLISH

AUDIO SETTINGS

SPEAKER SIZE

X’OVER

DTA SETTINGS CAR SETTINGS

• [SUB-W LEVEL]

Depending on the crossover type you have selected crossover or 3-way crossover setting items will be shown. By default, 2-way crossover type is selected.

For settings,

is selectable only if

23, Digital Time Alignment settings

[SUBWOOFER SET]

is set to

( 5)

[ON]. ( 20)

, 2-way

( 22)

Crossover settings

Below are the available setting items for 2-way crossover and 3-way crossover.

SPEAKER SIZE

Selects according to the connected speaker size for optimum performance.

•

The frequency and slope settings are automatically set for the crossover of the selected speaker.

•

When 2-way crossover is selected, if

[FRONT], [REAR]

the speaker is not available.

• When 3-way crossover is selected, if

[SPEAKER SIZE]

X ‘ OVER

• [FRQ]

Adjusts the crossover frequency for the selected speakers (high pass filter or low pass filter).

[THROUGH]

•

[FRONT-HPF SLOPE]/[REAR-HPF SLOPE]/[SW LPF SLOPE]/[HPF SLOPE]/[LPF SLOPE] [SLOPE]:

Selectable only if a setting other than crossover frequency.

• [SW LPF PHASE]/[PHASE]:

line with the other speaker output.

• [GAIN LEFT]/[GAIN RIGHT]/[FRONT-HPF GAIN]/[REAR-HPF GAIN]/[SW LPF GAIN] [GAIN]:

and

[SUBWOOFER]

, the

[X’OVER]

setting of

[FRONT-HPF FRQ]/[REAR-HPF FRQ]/[SW LPF FRQ]/[HPF FRQ]/[LPF FRQ]

is selected, all signals are sent to the selected speakers.

Adjusts the crossover slope.

Selects the phase of the speaker output to be in

Adjusts the output volume of the selected speaker.

[NONE]

for

[SPEAKER SIZE]

[NONE]

[WOOFER]

is selected for

is not available.

[THROUGH]

[TWEETER]

, the

[X ‘ OVER]

setting of

[WOOFER]

is selected for the

ENGLISH

+ 47 hidden pages

Kenwood KDC-X5200BTM Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual