Jensen JHD3620 User Manual

Download

CAT-

CAT+

DN UP

INFO

ENTER

INFO

ENTER

PTY/CAT

DISP

SCROLL

DISP

SCROLL

AS/PS

FAV

AS/PS

FAV

JHD3620

AM/FM/RBDS/WB/CD/USB/AUX-IN/iPod Ready/SIRIUS Ready Heavy Duty Radio

Installation and Operation Manual

Guide d’inst allation et d’opération

CONTENTS

Introduction......................................................................................................... 1

Safety Information .............................................................................................. 2

Installation........................................................................................................... 3

Wiring................................................................................................................... 4

Basic Operation .................................................................................................. 5

Tuner Operation.................................................................................................. 8

CD/MP3/USB Playback..................................................................................... 10

Satellite Radio Operation................................................................................. 11

iPod Operation.................................................................................................. 13

Care and Maintenance................................................ .................................... .. 14

Troubleshooting................... .. ........................................................................... 14

Specifications ............................................... ... ................................................. 15

CONTENU

JHD3620

MOUNTING SCREW

REMOVAL TOOL

MOUNTING BUSHING

MOUNTING STRAP

DIN SLEEVE

FLANGE NUTS

HARDWARE KIT CONTENTS

INTRODUCTION

System Features

Features of the Jensen JHD3620 mobile audio system include:

• Full Dot Matrix LCD

• AM/FM US/EURO Tuner with 30 Presets (12 AM, 18 FM)

• RBDS (Radio Broadcast Data Service) with PTY Search

• SIRIUS Radio Ready with Song Seek

• Single In-Dash CD Player with MP3/WMA Playback Capability

• USB Playback of MP3 and WMA files

• CD ESP (Electronic Skip Protection) 30 Sec.

• iPod Ready (Cable Sold Separately)

• Weatherband Tuner with SAME Technology

•Mute

• Pre-set Equalizer - 5 settings (Flat, Rock, Pop, Classical, User)

• Electronic Bass, Treble, Balance and Fader Controls

• Output Power 45W x 4

• Clock 12/24 Hour Selectable

• Public Announcement (PA) Feature with Optional Microphone (sold separately)

• IR Wireless Remote Control Ready (sold separately)

• 2-Channel Pre-amp Line Level Outputs

• 2-Wire Power with Non-Volatile Memory and Clock/Time Support

• Auxiliary Audio Input (Front 3.5mm Stereo Jack, Rear RCA)

Content List

• Jensen Heavy Duty Radio

• Hardware Kit

• 15AMP Fuse

• Installation Manual

• Quick reference Guide

SAFETY INFORMATION

REWRITABLE

RECORDABLE

Insert label Do not bend.

Never touch the under side of the disc.

Wipe clean from the center to the edge.

side up.

When Driving

Keep the volume level Iow enough to be aware of the road and traffic conditions.

When Washing Your Vehicle

Do not expose the product to water or excessive moisture. Moisture can cause electrical shorts, fire or other damage.

When Parked

Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a chance to cool down before starting playback.

Use the Proper Power Supply

This product is designed to operate with a 12 volt DC negative ground battery system.

Protect the Disc Mechanism

Avoid inserting any foreign objects into the disc slot. Misuse may cause malfunction or permanent damage due to the precise mechanism of this unit.

CAUTION:

THIS MOBILE CD PLAYER IS A CLASS I LASER PRODUCT. THIS UNIT USES A VISIBLE/ INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION IF EXPOSED DIRECTLY. BE SURE TO OPERATE THE MOBILE CD PLAYER AS INSTRUCTED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. PLEASE REFER SERVICING TO A QUALIFIED TECHNICIAN.

WARNING:

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

DISC NOTES

Depending on the recording status, conditions of the disc, and the equipment used for recording, some CD-Rs/CD-RWs may not play on this unit. For more reliable playback, please adhere to the following recommendations:

• Use CD-RWs with speed 1x to 4x and write with speed 1x to 2x.

• Use CD-Rs with speed 1x to 8x and write with speed 1x to 2x.

• Do not play a CD-RW which has been written more than 5 times.

JHD3620

Compatible Disc Types

Table 1: General Disc Information

Disc Type Logo

Audio CD 12 cm single side 74 minutes

NOTE: CD-R and CD-RW discs will not play unless the recording session is closed and the CD is finalized.

Disc Maintenance

• A dirty or defective disc may cause sound dropouts while playing. Before playing, wipe the disc using a clean cloth, working from the center hole towards the outside edge. Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent.

• Be sure to use only round CDs for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.

• Do not stick paper or tape on the disc. Do not use CDs with labels or stickers attached or that have sticky residue from removed stickers.

• Do not expose discs to direct sunlight or heat sources.

NOTE: A disc may become scratched (although not enough to make it unusable) depending on how you handle it and other conditions in the usage environment. These scratches are not an indication of a problem with the player.

Diameter/

Playable Sides

Playback Time

182

Dashboard

Bend Tabs

Screw Stud

Dashboard

Plain Washer

Screw (5 x 25mm)

Hex Nut (5mm)

Screw Stud

Support Strap

Rubber Bushing

Removal Key

Sleeve

Removal Key

JHD3620

INSTALLATION

This unit is designed for installation in vehicle cabs with an existing 1-DIN radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. See the dealer where the radio was purchased for kit availability. Always check the kit application before purchasing to make sure the kit works with your vehicle.

Before You Begin

1. Disconnect Battery Before you begin, always disconnect the battery negative terminal.

2. Remove Transport Screws

Important Notes

• Before final installation, test the wiring connections to make sure the unit is connected properly and the system works.

• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle.

• Install the unit where it does not interfere with driving and cannot injure passengers during a sudden or emergency stop.

• If the installation angle exceeds 30º from horizontal, the unit might not give optimum performance.

• Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or subject to excessive dust, dirt or vibration.

DIN Front Mount

1. Slide the mounting sleeve off of the chassis if it has not already been removed. If it is locked into position, use the removal keys (supplied) to disengage it. The removal keys are depicted in “Removing the Unit” on page 3.

2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

3. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.

4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

5. Follow the wiring diagram carefully and make certain all connections are secure and

6. After completing the wiring connections, turn the unit on to confirm operation (vehicle

insulated with crimp connectors or electrical tape to ensure proper operation.

accessory switch must be on). If the unit does not operate, recheck all wiring until the

problem is corrected. Once proper operation is achieved, turn the accessory switch off and proceed with final mounting of the chassis.

7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.

8. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and plain washer provided. Bend the strap, as necessary, to position it. Some vehicle installations provide cavity for rear support. In these applications, place the rubber bushing over the screw stud and insert the radio.

CAUTION: The perforated rear support strap or rear rubber mounting bushing must be used in the installation of the radio. Installation without either may result in damage to the radio or the mounting surface and void the manufacturer’s warranty.

9. Test radio operation by referring to the operating instructions for the unit.

Removing the Unit

To remove the radio after installation, remove the plastic end caps, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit.

Reconnect Battery

When wiring is complete, reconnect the battery negative terminal.

WIRING

JHD3620

CAT-

CAT+

DN UP

INFO

ENTER

INFO

ENTER

PTY/CAT

DISP

SCROLL

DISP

SCROLL

AS/PS

FAV

AS/PS

FAV

JHD3620

POWER

JHD3620

BASIC OPERATION

Power On/Off

Press the rotary encoder POWER button (1) to turn the unit on or off. The unit will resume at the last mode selected (Tuner, Auxiliary, etc.).

Volume Control

To increase the volume, turn the rotary encoder (1) to the right. To decrease the volume, turn the rotary encoder to the left. While adjusting the volume, the LCD displays a bar graph and numerical representation of the level.

The maximum volume setting is 40.

Mute

Press the MUTE button (24) to mute the audio output. Press MUTE again to restore the audio output to the previous level.

Mode

Press the MODE button (4) to select a different mode of operation, as indicated on the display panel. Available modes include the following: Tuner (AM/FM) > SAT (Sirius) > iPod > CD > USB > Auxiliary. Tuner is the default source when a prior source is no longer available.

NOTE: CD, iPod, USB or Sirius (SAT) mode will be skipped if the module is not installed.

NOTE: Sirius (SAT) mode will be skipped when the Region menu option is set to “EURO”.

Reset

The reset button should be activated for the following reasons:

• initial installation of the unit when all wiring is completed

• function buttons do not operate

• error symbol on the display

Use a ball point pen or thin metal object to press the RESET button (23). This may be necessary should the unit display an error code.

Audio Menu

Press the AUDIO button (3) to access the audio menu. You can navigate through the audio menu items by pressing the AUDIO button repeatedly. Once the desired menu item appears on the display, adjust that option by turning the rotary encoder (1) within 5 seconds. The unit will automatically exit the audio menu after five seconds of inactivity. The following menu items can be adjusted.

Bass Level

Use the rotary encoder (1) to adjust the Bass level range from “-7” to “+7”.

Treble Level

Use the rotary encoder (1) to adjust the Treble level range from “-7” to “+7”.

Balance

Adjusting Balance controls the relative level between the left and right speakers in each pair. Use the rotary encoder (1) to adjust the Balance between the left and right speakers from “Left 12” to “Right 12”.

Fader

Adjusting Fade controls the relative level between the front and rear speaker pairs. Use the rotary encoder (1) to adjust the Fader between the rear and front speakers from “Rear 12” to “Front 12”.

JHD3620

System Menu

1. Press and hold the PTY/CAT/MENU button (2) for more than 2 seconds to enter the system menu. The first menu item, “Key Beep”, will appear on the display.

2. Press the TUNE/SEEK |<< / >>| (18, 19) button repeatedly to navigate the system menu.

3. Press the INFO/ENTER button (16) to select the desired item.

4. Press the INFO/ENTER button again to adjust the selected menu item.

The following items can be adjusted:

• Key Beep (Click / Beep / Off): Turn the audible beep On/Off (heard when functions/ buttons are selected).

• LCD Backlight (1-10): Adjust LCD brightness.

• LCD Contrast (1-10): Adjust LCD contrast.

• Tuning Region (USA / EURO): Set frequency spacing for various regions.

• Power-Off Clock (On / Off)

• Clock Format (12Hour / 24Hour): Select 12 or 24 hour display mode.

• Set Clock (HH : MM):

• Press the INFO/ENTER button (16) to view the clock set screen.

• Press the INFO/ENTER button to move to the next digit.

• Press the TUNE/SEEK |<< / >>| (18, 19) buttons to adjust the selected digit.

• Preset-Only Tuning (On / Off):

• Sirius Settings Menu (only appears when SIRIUS tuner is connected and in SIRIUS mode)

• Clock Autoset (On / Off)

• Time Zone1 (Atlantic / Eastern / Central / Mountain / Pacific / Alaska

• Daylight Saving Time (Observed / Not Observed)

• Clear Skipped Channels (Yes / No)

• Skipped Channels: List of Channels (Skipped / Visible)

• Set Lock Code: _ _ _ _

• Locked Channels: List of Channels (Locked / Unlocked)

• Enable Song Seek (Yes / No)

• Edit Favorite Songs: List of Favorite Songs (Enable / Disable / Delete)

• iPod Auto-Select (On / Off): Choose “On” to automatically detect and playback iPod when connected or “Off” to use the MODE button to select the iPod source.

• Weather Alert Configuration

• Min Alert Level (All / None / Warnings / Watches)

• Auto-On Enable (Yes / No): Select “Enabled” to turn on the radio when NOAA alerts

are issued. This function only works when the +12V switched is on.

• Alert Volume (Select Volume Level 0-40)

• Clear SAME Codes <ENTER>

• SAME Code 1: _ _ _ _ _ _

• SAME Code 2: _ _ _ _ _ _

• SAME Code 3: _ _ _ _ _ _

• SAME Code 4: _ _ _ _ _ _

• SAME Code 5: _ _ _ _ _ _

• SAME Code 6: _ _ _ _ _ _

• SAME Code 7: _ _ _ _ _ _

• Battery Alarm (Off / On)

• Battery Auto-Off (Off / On)

• Reset System Defaults <ENTER>: Press the INFO/ENTER button (16) to return the EEPROM to factory default set up values.

• Update Firmware <ENTER>: Press the INFO/ENTER button (16) to apply recent software updates.

Equalizer

Press the EQ/LOUD button (11) to choose one of the following pre-defined bass and treble curves: USER > FLAT > ROCK > CLASSICAL > POP.

Loudness

Press and hold the EQ/LOUD button (11) to toggle loudness on/off. When listening to music at low volumes, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing.

Auxiliary Input

To access an auxiliary device:

1. Connect the portable audio player to either the AUX IN on the front panel (17) or at the rear of the unit.

2. Press the MODE button (4) to select “Auxiliary” mode. The rear AUX IN audio source will play by default until a device is inserted into the front jack.

3. Press MODE again to cancel “Auxiliary” mode and go to the next mode.

NOTE: The front AUX IN jack will override the rear auxiliary audio inputs.

PA Operation (microphone sold separately)

• Connect the PA Microphone with a 4-PIN connector to the 4-PIN socket on the rear of the unit.

• The unit will automatically switch to PA mode when the Mic switch is pushed “ON”.

• The PA output level can be adjusted using the rotary volume encoder (1).

• With radio power off, the radio will wake up when PA mic is keyed to make an announcement. Please note that it will take a few seconds before the radio “wakes up” and PA is active. Radio will return to the off state when the PA mic is released.

Liquid Crystal Display (LCD)

The current frequency and activated functions are shown on the LCD panel (21).

NOTE: LCD panels may take longer to respond when subjected to cold temperatures for an extended period of time. In addition, the visibility of the characters on the LCD may decrease slightly. The LCD display will return to normal when the temperature increases to a normal range.

JHD3620

Setting the Clock

To set the clock to display the current time, turn the vehicle ignition on and turn the radio on. Enter the system menu and adjust the clock by selecting the “Set Clock” menu item.

• Press the INFO/ENTER button (16) to view the clock set screen.

• Press the INFO/ENTER button to move to the next digit.

• Press the TUNE/SEEK |<< / >>| (18, 19) buttons to adjust the selected digit.

When no adjustment is made for five seconds, the time will become set and normal operation will resume.

Scroll

When the information is too long to be displayed on the LCD, press the DISP/SCROLL button (12) to view the entire title. The information will scroll twice and then return to abbreviated text.

TUNER OPERATION

CAT-

CAT+

DN UP

INFO

ENTER

INFO

ENTER

PTY/CAT

DISP

SCROLL

DISP

SCROLL

AS/PS

FAV

AS/PS

FAV

JHD3620

Automatically Store / Preset Scan (AS/PS)

Automatically Store

Select an AM or FM band. Press and hold the AS/PS/FAV button (14) for more than 2 seconds to automatically select 18 strong stations (12 for AM). “Storing Presets” appears on the screen and the new stations replace any stations already stored.

Preset Scan

Select a band. Press AS/PS/FAV (14) to scan stations stored in the current band. The unit will pause for 5 seconds at each preset station. Press AS/PS/FAV again to stop scanning when the desired station is reached.

RBDS Operation

This unit is equipped to display RBDS (Radio Broadcast Data Service) information when broadcast by the radio station.

NOTE: Radio stations broadcasting RBDS may not be available in your listening area.

Select a Band

Press the BAND/WB button (15) to change between three FM bands and two AM bands. Press and hold the BAND/WB button to access the Weatherband (WB).

Manual Tuning

Press the TUNE/SEEK >>| or |<< buttons (19, 18) to seek stations up/down step by step.

Auto Seek Tuning

Press and hold the TUNE/SEEK >>| or |<< buttons (19, 18) to automatically seek the next or previous strong station.

NOTE: Seek tuning is not available for weather band channels. Use the up or down tuning buttons to manually select any of the seven available weather band channels.

Preset Stations

In FM radio mode, press the PTY/CAT/MENU button (2) to list the following Program Type (PTY) options: ANY / News / Information / Sports / Talk / Rock / Classic Rock / Adult Hits / Soft Rock / Top 40 / Country / Oldies / Soft / Nostalgia / Jazz / Classical / Rhythm and Blues / Soft Rhythm & Blues / Foreign Language / Religious Music / Religious Talk / Personality / Public / College / Weather / Emergency Test / ALARM! ALARM!

To search for stations in a PTY category:

1. Press the PTY/CAT/MENU button (2) to view the current PTY category.

2. Press the TUNE/SEEK >>| or |<< buttons (19, 18) to move through the list of available categories and select the program type you wish to search.

3. After selecting the desired PTY, press the PTY/CAT/MENU button (2) to search the band for broadcasts of this type. “PTY Search” is displayed while the tuner is searching.

NOTE: Performing a PTY search on “ANY” will Seek Tune and stop on any station broadcasting RBDS, regardless of the program type.

Six numbered preset buttons store and recall stations for each band.

Store a Station

Select a band (if needed), then select a station. Press and hold a preset button (5-10) for two seconds. The preset number will appear on the LCD.

Recall a Station

Select a band (if needed). Press a preset button (5-10) to select the corresponding stored station.

NOTE: Preset buttons are pre-assigned frequencies in weather band mode.

JHD3620

Weather Band Operation

What is the NOAA Weather Radio/Weatheradio Canada?

NOAA (National Oceanic and Atmospheric Administration) is a nationwide system that broadcasts local weather emergency information 24 hours a day via the National Weather Service (NWS) network. The U.S. network has more than 530 stations covering the 50 states as well as the adjacent costal waters, Puerto Rico, the U.S. Virgin Islands and the U.S. Pacific Territories. Each local area has its own transmitting station and there are a total of seven broadcasting frequencies used. A similar system is available in Canada under the Weatheradio Canada service administered by Environment Canada.

Tuning to Weatherband

Press and hold the BAND/WB button (15) to access the Weatherband. The indication "WB" will appear on the display panel, along with the current number and channel indication: "WB-1", “WB-2", "WB-3", "WB-4", "WB-5", "WB-6" or "WB-7". The seven frequencies are shown in the following table:

Table 2: WB Frequencies

Frequency (MHz) Preset

162.400 2

162.425 4

162.450 5

162.475 3

162.500 6

162.525 -

162.550 1

The above table also shows which preset button will access the frequency. Note that one frequency cannot be accessed using a preset button. The frequency can only be reached using the tuning controls.

Use the TUNE/SEEK >>| or |<< buttons (19, 18) or the preset buttons to tune to each of the seven channels until you find the weatherband station broadcasting in your area.

How many stations can I expect to receive?

Since the broadcasts are local weather and information, the transmission power is usually very low (much less than standard AM or FM stations) so you will usually receive only one station unless you are on the edge of two or more broadcast signals. The most you will receive will be two or three, and that is rare.

Is it possible I won't receive any stations?

Depending on where you are located, there is a possibility you will receive only a very weak signal or none at all. Also, similar to AM and FM signals, weatherband signals are subject to surrounding conditions, weather, obstructions of the signal by hills or mountains, etc.

NOAA Weather Alert

The Weather Alert function adds an additional level of user safety by automatically switching from any of the available function modes to weather band for a minimum of 60 seconds if a NOAA warning tone (1050 Hz) is received/detected. If no additional warning tone is received for 60 seconds, the unit will switch back to the last known function mode. See “System Menu” on page 6 to learn how to turn the WB Alert feature on.

SAME Decoding and Filtering

Specific Area Message Encoding (SAME) data is also broadcast prior to alert broadcasts. SAME data contains information about the geographic region affected by the alert, the type of alert, and its effective time. The geographic region included in the SAME data is called the Geographical Area code and has the form PSSCCC where “P” represents a portion of the county, “SS” is a two-digit state, territory, or offshore marine area identifier and “CCC” identifies the county, province, or major metropolitan area within the state. This unit can be configured through the system setting menu with up to seven Geographical Area codes to limit the automatic tuning or power on functions described above.

SAME data also includes the type of alert being broadcast. This unit can be configured through the System Setting Menu to limit the automatic tuning or power on functions based on the type of alert.

SAME is activated by programming a 6 digit code - called a FIPS code - into your radio. The FIPS code or Federal Information Processing System code is a six digit code that identifies the states and counties (or parishes) in the United States. The first digit identifies the county subdivision. The next two digits identify the state or territory, and the last three identify the county. The FIPS code for your area can be found by calling the NWS toll free number or visiting the web site.

The phone number is 1-888-NWS-SAME (1-888-697-7263) Upon calling, an automated system will prompt you to enter your state and county. When you confirm the information, the system will provide your six digit FIPS code.

The web site is: www.nws.noaa.gov/nwr/indexnw.htm. Upon selecting your state from the chart, you will see a listing of all the counties in that state. For each county there is a listing of the SAME# (FIPS code), the location of the transmitter, the WB frequency, the call sign, the transmitter power and miscellaneous remarks.

NOTE: Because broadcast areas overlap you may want to set more than one S.A.M.E. location. If you live near the border between counties, you may want to receive alerts from more than one tower.

Your radio is capable of being programmed with up to 7 different FIPS location codes. The default code has been programmed at the factory - 000000 - to respond to all messages within your area.

CAT-

CAT+

DN UP

INFO

ENTER

INFO

ENTER

PTY/CAT

DISP

SCROLL

DISP

SCROLL

AS/PS

FAV

AS/PS

FAV

JHD3620

CD/MP3/USB PLAYBACK

Repeat Play

• Press the 1/RPT button (8) during disc play to repeat the current track.

• Press 1/RPT again to stop repeat play.

Random Play

• Press the 3/RDM button (5) during disc play to play all tracks in the current folder in random, shuffled order.

• Press 3/RDM again to stop random play.

Folder Navigation (MP3 Only)

• Press the PTY/CAT/MENU button (2) to view a list of all songs in the current folder.

• Press the PTY/CAT/MENU button again to navigate up through the file structure.

• Press the >>| / UP (19) and |<< / DN (18) buttons to navigate the list.

• Press the INFO/ENTER button (16) to play the highlighted song or view files in the selected folder. Continue pressing INFO/ENTER until the desired file is selected.

The unit will automatically exit the folder navigation menu after 5 seconds of inactivity.

MP3 Specifications

Digital File Playback

If the user inserts a data disc or connects a USB mass storage device, the radio automatically powers on, if necessary, and switches to digital file playback mode and selects that physical media. The bottom left corner of the LCD displays the name of the source. Changing modes or turning off the radio pauses playback.

Playback shall resume exactly where paused when returning to digital file playback mode.

Inserting and Ejecting a Disc

Insert a disc, label-side up, into the disc slot (22). The unit will automatically draw the disc in and play the first track on the disc, whether the power was turned on or not.

Press the eject button (20) to stop disc play and eject the disc. The unit does not have to be on to eject the disc. Disc will retract if not removed.

Inserting a USB Device

The USB connector (17) is located on the right side of the front panel, behind a protective rubber cover. Pull gently to lower the rubber cover and reveal the USB slot. Insert a USB device to switch to USB mode and begin playback.

Controlling File Playback

Selecting Tracks

Press the TUNE/SEEK >>| (19) or TUNE/SEEK |<< button (18) to advance to the next track/ file. The selected track number will appear on the display. Press and hold the TUNE/SEEK >>| or |<< button to fast forward or fast reverse. Playback begins when the button is released.

Play/Pause Disc Playback

Press the MUTE/>|| button (24) to suspend playback. “Pause” is displayed on the screen. Press the MUTE/>|| button again to resume play.

Previewing Tracks

Press the 2/INT button (6) to play the first 10 seconds of each track in the current folder sequentially. Press 2/INT again to stop Intro Scan and resume normal play at the current track.

Notes on MP3 Playback

• Any directory that does not include an MP3 file is skipped

• Maximum number of folders: 512 (including skipped directories)

• Maximum number of folder levels: 12

• Maximum number of MP3 files: 999

• Maximum number of characters for MP3 file name and folder name: 32

• Sampling frequency: 16KHz, 22.05KHz, 24KHz, 32KHz, 44.1KHz, 48KHz

• Bit rates: maximum 384 Kbps

• Maximum number of Characters of ID3 Tag:

• ID3 Tag version 1.0: 32

• ID3 Tag version 2.x: 32

File Playing Order

Files will be continually played sequentially within the current folder. To play songs in another folder, press the PTY/CAT/MENU button (2) twice to move up a folder level. Press the >>| / UP (19) and |<< / DN (18) buttons to navigate the list and then press the INFO/ENTER button (16) to access the selected song or folder.

You may be able to set the order in which MP3/WMA are to be played by writing them onto a medium such as a CD-R with their file names beginning with play sequence numbers such as "01" to "99".

JHD3620

CAT-

CAT+

DN UP

INFO

ENTER

INFO

ENTER

PTY/CAT

DISP

SCROLL

DISP

SCROLL

AS/PS

FAV

AS/PS

FAV

JHD3620

SATELLITE RADIO OPERATION

Switching to Sirius Satellite Radio (Requires optional Sirius tuner)

Press the MODE button (4) to change the mode to Sirius radio mode.

Accessing your Sirius RADIO ID

To display your Sirius radio ID, use the TUNE/SEEK |<< button to tune to channel “000”. The screen will display “Sirius ID” with the SID displayed in the middle of the LCD screen. The Sirius radio ID is 12 characters long.

Selecting a Band

In Sirius mode, press the BAND/WB button (15) to access the Sirius user-preset channel groups in the following order: SR1, SR2, SR3.

Category Tuning

1. Press the PTY/CAT/MENU button (2) to access Category mode.

2. While in category mode, press 5/CAT- OR 6/CAT+ buttons (9, 10) to choose a category.

3. Press the TUNE/SEEK |<< / >>| buttons (18, 19) to choose desired channels in that category. (The current channel number within the chosen category will always be the default first channel tuned.)

4. Press the PTY/CAT/MENU button to return to channel tuning mode.

Channel Up/Down Tuning

Press the TUNE/SEEK |<< / >>| buttons (18, 19) to search for a channel. Press and hold the TUNE/SEEK buttons to fast search.

Direct Tuning Mode

1. Press and hold the INFO/ENTER button (16) to enter direct tuning mode.

2. Press TUNE/SEEK |<< / >>| buttons (18, 19) to change the first of three digits for the desired channel in the direct entry screen.

3. Press the INFO/ENTER button to confirm the entered digit and move to the second digit field.

4. Press TUNE/SEEK |<< / >>| buttons to select the second digit.

5. Press the INFO/ENTER button to confirm the entered digit and move to the third digit field.

6. Press TUNE/SEEK |<< / >>| buttons to select the third digit.

7. Press the INFO/ENTER button to confirm the three digit channel and tune to the selected channel.

Storing Preset Channels

The preset buttons (5-10) can be used to store 6 channels, allowing convenient access to your favorite channels.

Programming Channels

1. Select the channel you want to store in memory.

2. Press and hold a preset button (5-10) until the corresponding preset button number appears.

3. Repeat steps 1 and 2 to program additional channels.

Preset Recall

Press one of the six preset buttons (5-10) to directly select a preset channel stored in the current band.

Preset Scan

Press AS/PS/FAV button (14) to scan stations stored in all three user-preset channel groups (SR1, SR2 and SR3). The unit will pause for 10 seconds at each preset station. Press AS/PS again to stop scanning when the desired station is reached.

Preset Tuning

In Preset Tuning Mode, you can use the TUNE/SEEK |<< / >>| buttons (18, 19) to access all 18 preset stations in sequential order. Access preset tuning mode through the system menu. Set Preset-Only Tuning to “ON.”

Alternate Display Mode

Press the DISP/SCROLL button (12) to change the display information between single and dual line text display. In dual line mode, both artist and title are available for viewing.

Press and hold the DISP/SCROLL button to scroll the Artist/Song Title information. While in category tuning list mode, press the DISP/SCROLL button in sequence to change the

display information from Channel Name, Artist, and Song Title.

JHD3620

Signal Strength Strength Display

No Signal

Weak

Good

Excellent

Satellite Signal Strength

The display will indicate satellite reception strength as shown below.

Channel Lock

Access Channel Lock through the System Menu under the “Sirius Satellite Radio” menu. See “System Menu” on page 6.

1. Select “Set Lock Code.”

2. No channels can be locked with the default 0000 code. To set the lock code: a. Press the TUNE/SEEK |<< / >>| (18, 19) buttons to enter the first digit of the default

code. b. Press the INFO/ENTER button to move to the next digit. c. Repeat above steps to enter all 4 digits of the default code. d. Press the TUNE/SEEK |<< / >>| (18, 19) buttons to enter the first digit of the new

code. e. Press the INFO/ENTER button to move to the next digit. f. Repeat above steps to enter all 4 digits. g. Repeat above steps to confirm the new code.

8. After setting a new four digit code, you can lock channels by entering the “Locked Channels” menu.

9. Upon entering the Locked Channels list, you will be prompted to enter your four digit code. a. Press the TUNE/SEEK |<< / >>| (18, 19) buttons to enter the first digit. b. Press the INFO/ENTER button to move to the next digit. c. Repeat above steps to enter all 4 digits.

4. After entering the code, you can navigate the list using the TUNE/SEEK |<< / >>| buttons to highlight the channels.

5. Press the INFO/ENTER button (16) to Lock (indicated by a icon) or Unlock ( ) the selected channel.

Favorites (Song/Artist Seek)

This feature lets you store and search for up to 15 Artist/Song combinations on Sirius Satellite Radio.

1. While the current song is playing, press and hold the AS/PS/FAV button (14).

2. Press the INFO/ENTER button (16) to select the Artist to be stored or press the AS/PS/ FAV button to select the Song to be stored.

Next time the stored artist or song is played on Sirius Satellite Radio, you will be notified with an alert and can then choose to tune to the channel playing the Song or Artist. The list of stored Artists/Songs can be managed through the System Menu under the “Sirius Satellite Radio” menu. See “System Menu” on page 6.

JHD3620

iPhone

iPod

HEAD UNIT

13 Din iPod Ready Cable

iPod Cable

iPod

CAT-

CAT+

DN UP

INFO

ENTER

INFO

ENTER

PTY/CAT

DISP

SCROLL

DISP

SCROLL

AS/PS

FAV

AS/PS

FAV

JHD3620

iPod OPERATION

This unit is equipped with an iPod ready function that will allow you to control your iPod (if compatible) using the control panel buttons. The following iPod versions are supported:

• iPod Nano (1G, 2G, 3G, 4G and 5G)

• iPod 5G

• iPod Classic

• iPhone, iPhone 3G, iPhone 3GS

• iPod Touch

• iPod Touch 2G

NOTE: Earlier model iPods are not supported because they do not implement the USB control protocol. Also, the iPod Shuffle is not supported because it does not utilize the 30-pin Apple iPod Connector. These unsupported iPod models may be connected to the radio using one of the Auxiliary Inputs.

NOTE: iPod and iPod Cable sold separately.

Accessing iPod Mode

T o enter iPod mode from any other source, press the MODE button (4) until “iPod” appears on the lower left corner of the display. If the user connects an iPod containing no songs, the radio will display a message stating “No Songs” when it enters iPod mode.

Turning the iPod On/Off

The iPod power turns on automatically when an iPod is connected to the 30-pin iPod cable, as long as the vehicle ignition is turned on. You can turn the iPod off by disconnecting it from the cable or by turning the ignition off. When the ignition is turned off, the iPod will pause and then enter sleep mode after 2 minutes. While the iPod is connected, the power cannot be turned on or off from the iPod itself.

NOTE: The iPod will continuously recharge when connected to the unit, as long as the vehicle ignition is turned on.

Controlling Playback

Pausing Playback

During playback, press the MUTE/>|| button (24) to pause the iPod player. “Pause” will appear on the LCD. Press MUTE/>|| again to resume playback.

Repeat Play

During playback, press the 1/RPT button (8) to repeat the current song. “RPT” will appear on the LCD. Press 1/RPT again to stop repeat playback.

Intro Play

During playback, press the 2/INT button (6) to play the first ten seconds of each song. “INT” will appear on the LCD. Press 2/INT again to stop intro playback.

Random Play

During playback, press the 3/RDM button (5) to play all songs in the current category in random order. Random play will begin once the current song has finished playing. “RDM” will appear on the LCD. Press 3/RDM again to stop random playback.

Selecting Tracks

During playback, press the TUNE/SEEK |<< / >>| buttons (18, 19) to play the previous or next track in the current category. Press the TUNE/SEEK |<< button (18) once to play the song from the start position or press TUNE/SEEK |<< twice to play the previous track. Pressing the TUNE/SEEK |<< button (18) during the first 2 seconds of a track will play the previous track. After 2 seconds, this action return to the beginning of the current track.

Press and hold the TUNE/SEEK |<< / >>| button (18, 19) to fast reverse/forward the song.

NOTE: If you press and hold the TUNE/SEEK |<< / >>| button to change the current song to the previous/next song, you will exit fast reverse/forward mode.

Playlist Search

Press the PTY/CAT/MENU button (2) to access Playlist selection mode. While in Category mode, press the TUNE/SEEK |<< / >>| buttons (18, 19) to choose file search by Playlist, Artist, Album, Genre, Song, Audiobook or Podcast. Press the INFO/ENTER button (16) to select the search mode. Use the TUNE/SEEK |<< / >>| buttons to search the available files on the iPod. Press the INFO/ENTER button to play the selected song or file.

Alternate Display Mode

Press the DISP/SCROLL button (12) to change the display information between single and double line text display.

CARE AND MAINTENANCE

• Keep the product dry. If it does get wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits.

• Keep the product away from dust and dirt, which can cause premature wear of parts.

• Handle the product gently and carefully. Dropping it can damage circuit boards and cases, and can cause the product to work improperly.

• Wipe the product with a dampened cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the product.

• Use and store the product only in normal temperature environments. High temperature can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts.

Ignition

The most common source of noise in reception is the ignition system. This is a result of the radio being placed close to the ignition system (engine). This type of noise can be easily detected because it will vary in intensity of pitch with the speed of the engine.

Usually, the ignition noise can be suppressed considerably by using a radio suppression type high voltage ignition wire and suppressor resistor in the ignition system. (Most vehicles employ this wire and resistor but it may be necessary to check them for correct operation.) Another method of suppression is the use of additional noise suppressors. These can be obtained from most professional mobile electronics retailers.

Interference

Radio reception in a moving environment is very different from reception in a stationary environment (home). It is very important to understand the difference.

AM reception will deteriorate when passing under a bridge or when passing under high voltage lines. Although AM is subject to environmental noise, it has the ability to received at great distance. This is because broadcasting signals follow the curvature of the earth and are reflected back by the upper atmosphere.

TROUBLESHOOTING

Symptom Cause Solution

No power The vehicle’s accessory

Disc cannot be loaded or ejected

No sound Volume is too low or system

The operation keys do not work

Sound skips The installation angle is

Cannot tune to radio station, auto-seek does not work

switch is not on

The fuse is blown Replace the fuse Presence of CD disc inside

the player

Inserting the disc in rev erse direction

Compact disc is extremely dirty or disc is defective

Condensation Leave the player off for an hour or

is muted Wiring is not properly con-

nected The built-in microcomputer

is not operating properly due to noise

more than 30 degrees The disc is dirty or defec-

tive. The antenna cable is not

connected The signals are too weak Select a station manually

If the power supply is properly connected to the vehicle’s accessory terminal, switch the ignition key to “ACC” or “Run”

Remove the disc in the player and insert the new one

If disc will not eject, press the RESET button

Insert the compact disc with the label facing upward

Clean the disc or try to play a new one

so, then try again Adjust volume to audible level

Check wiring connections

Press the RESET button

Adjust the installation angle to less than 30 degrees

Clean the disc and try to play again or use new disc

Check antenna cable

JHD3620

SPECIFICATIONS

Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >

Channel Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .: More than 50 dB

Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : 20 Hz - 20 kHz

FM Radio

Frequency Coverage (USA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5 to 107.9 MHz

Frequency Coverage (Europe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5 to 108 MHz

Sensitivity (S/N=30dB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2µV

Image Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >45 dB

Stereo Separation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >25 dB

AM/MW

Frequency Range (USA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530-1710 kHz

Frequency Range (Europe). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522-1620 kHz

Sensitivity (S/N=20dB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 dB

General

Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DC 12 Volts

Grounding System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative Ground

Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8 ohms per channel

Tone Controls:

Bass (at 100 Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : ±10 dB

Treble (at 10 kHz). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : ±10 dB

Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45W x 4

Idle/Standby Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75mA

Current Drain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Ampere (max.)

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 (W) x 175 (D) x 50 (H)

65 dB

ASA Electronics Corporation

www.asaelectronics.com

www.jensenheavyduty.com

v.120709

Jensen JHD3620 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual