Jensen JEN99BT3BCF4, JEN99BT3SBCF4 User Manual

Transmitter Programming Guide

Model :

JEN99BT3BCF4

& JEN99BT3SBCF4

The transmitters included with the system have been pre-programmed at the
factory, with each button pre-assigned to control a specific function of the
system. Although the system in the vehicle has either a 3, 4, or 5 channel
RECEIVER, depending on the model, the transmitters included with the system
are 7 channel transmitters. This allows you to program each transmitter to
more than one vehicle in two car families and also allows you to change which
button or buttons control certain functions of the system.
(

Example:

activate Receiver channel 2.) Refer to the chart below for access to each of
the transmitter channels, and for the standard factory button assignments.

CHANNEL BUTTONS CHANNEL FUNCTION

Transmitter channel 5, shown below, can be programmed to

TRANSMITTER SYSTEM RECEIVER

1 1 Remote Arm & Disarm

*Remote Emergency Panic
*Remote Door Lock & Unlock

2 OPT. 1 3 Push And Hold For 3 Seconds For Opt1

Release, Push 2 Times For Aux. Out.
3 OPT. 2 4 ** Pulsed Output for Accessories
4 5 ** Switched Output for Accessories
5-­6-­7--

* Remote Emergency Panic is available only on certain models.
* Door Lock/Unlock may require additional components in certain vehicles.
** Some of the more common accessories for these additional channels are;

&

&

&

& &

AS 9075 Remote Car Starter
AS 9256 Remote Trunk Release Relay
AS 9154 Remote Garage Door Interface
AS 9153 Remote Window Roll Up

128-7054

1 of 8

PROGRAMMING TRANSMITTERS:

It is important to remember that during programming, each individual step of
the procedure must be executed within 15 seconds of the previous step. When
the 15 second time limit is allowed to expire, the system will automatically exit
program mode. This is indicated by a long "chirp" from the siren.

Additionally, any time the ignition key is turned off while programming, the
system will immediately exit program mode. This is also indicated by a long
"chirp" from the siren.

TO PROGRAM ADDITIONAL TRANSMITTERS:

NOTE: The programming information described below assumes that the

default transmitter is being used and the Lock/Unlock button is one and
the same. If you have the optional transmitter with a separate Lock
and Unlock button, use letter "B" reference below for programming.

Also, where indicated that the siren will emit a long chirp tone, the
optional horn may be connected, in which case either or both the horn
and siren may sound.

1. (a ) Enter the vehicle, and turn the ignition key to the "on" position.
(b ) Enter the vehicle, and turn the ignition key to the "on" position.

2. (a ) Press and release the valet/bypass push button switch 3 times.
(b ) Press and release the valet/bypass push button switch 3 times.

3. (a ) The dash LED will flash one time and the siren will "chirp" 1 time

indicating the system is ready to accept programming for channel
1, Arm/Disarm, Lock/Unlock and Panic.

(b ) The dash LED will flash one time and the siren will "chirp" 1 time

indicating the system is ready to accept programming for channel
1, Arm/Lock and Panic.

4. (a ) You can assign the Lock/Unlock, Arm/Disarm button, by pressing

and holding the lock/unlock button until the siren emits a long chirp
tone. The chirp tone confirms that programming of channel 1 was
successful.

Up to 4 transmitters can be programmed, press and hold the selected button
of each additional transmitter until the chirp tone is heard, or press and release
the valet push-button switch two times to advance to step #8.

(b ) You can assign the Lock/Arm button by pressing and holding the

lock button until the siren emits a long chirp tone.

2

128-7054

2 of 8

The chirp tone confirms that programming of channel 1 was success
ful. Up to 4 transmitters can be programmed, press and hold the
selected button of each additional transmitter until the chirp tone is
heard, or move to step #5

5.Press and release the valet/override switch one time to advance to
channel 2.

6. (a ) Disregard this step.
(b ) The dash mounted LED will flash 2 times, and the siren will "chirp"

2 times indicating that the system is ready to accept programming for
channel 2. Unlock/2nd Unlock, Disarm, and Panic. Press and hold
the Unlock button on your keychain transmitter until the siren emits
a long chirp tone. This confirms that programming of channel 2 was
successful. Up to 4 transmitters can be programmed, press and hold
the selected button of each additional transmitter until the chirp tone
is heard.

7. Press and release the valet/override switch one time to advance to channel

3.

8. The dash mounted LED will flash 3 times, and the siren will "chirp" 3
times, indicating that the system is ready to accept programming for
channel 3. Trunk Release Output, (where so equipped), or alternate
channel output when used.

9. (a) Press and hold the 1st Opt. button on your keychain transmitter until

the siren emits a long chirp tone. This confirms that programming of
channel 3 was successful. Up to 4 transmitters can be programmed,
press and hold the selected button of each additional transmitter until
the chirp tone is heard.

(b) Press and hold the Opt. button on your keychain transmitter until the

siren emits a long chirp tone. This confirms that programming of
channel 3 was successful. Up to 4 transmitters can be programmed,
press and hold the selected button of each additional transmitter until
the chirp tone is heard.

10. Press and release the valet/override switch one time to advance to channel
4 if so equipped. If your system does not have a 4th channel, a long chirp
followed by a short chirp tone will indicate that the program mode has been
exited.

11. The dash mounted LED will flash 4 times, and siren will "chirp" 4 times
indicating that the system is ready to accept programming of channel 4.

3

128-7054

3 of 8