Jenn-Air CCG2423B, CCG2423Q, CCG2423S, CCG2423W Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand [phone]

This Data Sheet Includes Information On

30"

Jenn-Air

•

Product Model Number (s):

•

30" Gas Cooktops:

3 7/16"

21"

CCG2423Q, CCG2423S, CCG2423B and CCG2423W

Side View (not to scale)

•

Dimensions (Actual Size)

•

Overall Dimensions

Overall width: 30"

Top View (not to scale)

Overall depth: 21"

Distance from top of counter to bottom of unit: 3 7/16"

	Cut-Out width: 26 9/16"				Cut-Out Dimensions
	Cut-Out depth: 20 1/16"			20 1/16"
					Countertop View
Min. spacing from cooktop edge to nearest
					(not to scale)
vertical combustible wall to the RIGHT: 2"
				26 9/16"
Min. spacing from cooktop edge to nearest
vertical combustible wall to the LEFT: 2"
Min. spacing from cooktop edge to nearest
vertical combustible wall to the REAR: 1 1/2"
Minimum spacing to front edge of counter: 2"
Minimum distance between cooktop
	and cabinet directly above: 30"				Cabinet Requirements
Minimum	width of cabinet directly above: 30"				Wall View
Maximum depth of cabinets directly					(not to scale)
	above and adjacent: 13"			30"
Minimum distance between countertop					Minimum horizontal
	and adjacent cabinet above: 18"			30"
•	Additional Information	•	18"		clearance between the
					edge of the appliance
• Electrical requirements : 110/120 volt AC, 60hz. Must
					and combustible
be grounded. 15amp circuit required. Locate outlet
					construction extending
below the cooktop a minimum of 3" below the
					from the cooking
countertop if not installing over an under counter oven.
					surface to 18" above
Locate outlet below the oven or in an adjacent cabinet
					the cooking surface is
when installing over an adjacent under counter oven.
					2" (see solid areas)
• Minimum clearance from top of counter to combustible
material below is 2 5/8"
• Countertop must be supported within 3" of cutout.
• Unit may be installed over an under counter oven.
• Gas requirements : The pressure regulator supplied
with this appliance is pre-set and fixed for correct
outlet pressure: 5"W.C. if this model is equipped for

use with natural gas; 10" W.C. if equipped for use with

9/16" to centerline of pipe from

Top view of cutout

when converting to LP. The maximum inlet gas supply

back edge of cutout

(not to scale)

pressure for the regulator is 14" W.C. The inlet test

pressure for checking the regulator must be at least 6"

Gas inlet location

W.C if equipped for natural gas; 11" W.C. if converted

to LP gas.

See page 2 for additional information

1 21/32" from left

side of cutout to

Subject to change without notice. This system is designed to

centerline of pipe.

be updated daily if necessary. Dimension Express is not

responsible for use of superseded, voided, or outdated data

sheets. Because of the difficulty or impracticability of deter-

mining actual damages, liability of Dimension Express shall

not exceed $50.00.

Cooktop supplied with 1/2" NPT female inlet on regulator

Copyright © Dimension Express, 2002.

321

• NEVER reuse Data Sheets. Data Sheets are subject to change without

• Call Dimension Express if you have any questions at [phone] •

notice. Dimension Express is a FREE service bureau and is updated daily,

• Always refer to a current Code at a Glance or manufacturer directory •

it makes far more sense to spend the time necessary to request new Data

• Data Sheet codes change on the first of odd numbered months at 12:01am •

Sheets for each project, as opposed to the problems, time, costs, and risks

BN182.34 • A321B149 • • 032603 • 95656 • 41867

associated with reusing old Data Sheets.