Ivoclar Vivadent SR Nexco Flask Short Instructions

Short instructions Kurzanleitung
1
Wax- Up
2
Transil F
3
4
SR Nexco Dentin
SR Nexco Opaquer
5
Screw down alternately
6
10
min
With flask
Mit Küvette
Abwechselnd verschrauben
7
Without flask
8
Cut-back
Ohne Küvette
9
SR Nexco Stains
10
SR Nexco Paste Incisal
SR Nexco Paste Effect
11
Screw down alternately
Abwechselnd verschrauben
13 14
Without flask
Ohne Küvette
12
With flask
Mit Küvette
Finishing and polishing
Finieren und polieren
see instructions
Polymerization Parameters / Polymerisationstabelle
Device Manufacturer Opaquer* Dentin** Liner, Incisal,
Quick Lumamat 100
Spectramat Ivoclar
Ivoclar Vivadent AG
Vivadent AG
20 s Quick
P2 / 11 min
20 s Quick 20 s Quick 20 s Quick 20 s Quick
5 min 5 min 2 min 5 min 2 min 2 min 5 min
Effect**, Margin**
Labolight LV-III GC 5 min 2 min 2 min 5 min 2 min 3 min 5 min
Solidilite V Shofu 3 min 1 min 1 min 3 min 1 min 3 min 5 min
Visio Beta Vario
3M Espe 7 min
without vacuum
4x 20 s
Visio Alfa
4x 20 s
Visio Alfa
HiLite Heraeus 180 s 90 s 90 s 90 s 90 s 90 s 180 s
Important information:
Regular maintenance and functional control of polymerization devices is required.
Notes:
Units suitable for intermediate curing: Quick (Ivoclar Vivadent AG), Hilite pre (Heraeus), Visio Alfa (3M), Sublite V (Shofu), Steplight SL-I (GC). * Thinly apply a first layer of opaque and precure it. Then apply the second
layer of opaque so that it covers the entire surface and cure it as indicated
in the polymerization table. ** Observe the maximum layer thickness! Precure, if required. *** Stains should only be applied in extremely thin layers – a very low curing
depth is achieved with dark shades.
Gingiva** Stains*** SR Connect Final
Polymerization
P2 / 11 min P2 / 11 min
4x 20 s
Visio Alfa
Wichtige Information:
Regelmässige Wartung und Funktionskontrolle der Polymerisationsgeräte wird vorausgesetzt.
Hinweise:
Geräte zum angelieren: Quick (Ivoclar Vivadent AG), Hilite pre (Heraeus), Visio Alfa (3M), Sublite V (Shofu), Steplight SL-I (GC). * erste Opaquerschicht dünn auftragen und zwischenhärten, zweite
Opaquerschicht deckend auftragen und nach Polymerisationstabelle härten. ** maximale Schichtstärken beachten! Ggf. zwischenhärten. *** Stains nur in dünnsten Schichtstärken auftragen – sehr geringe Durchhärtung bei dunklen Farben.
4x 20 s
Visio Alfa
4x 20 s
Visio Alfa
2x 7 min
without vacuum
see instructions
Ivoclar Vivadent AG FL-9494 Schaan / Liechtenstein
www.ivoclarvivadent.com
Date information prepared: 2014-08-xx, Rev. 0
673059d/e
Loading...