International CR-W400U User Manual
High Power Receiver
CR-W400U
Operating Instructions
Please read these instructions carefully before using this product and save this manual for future use.
2
Panasonic welcomes you to our ever growing family of electronic product owners. We know that this
product will bring you many hours of enjoyment. Our reputation is built on precise electronic and
mechanical engineering, manufactured with carefully selected components and assembled by people
who take pride in their work. Once you discover the quality, reliability, and value we have built into this
product, you too will be proud to be a member of our family.
❏
Use This Equipment Safely
When Driving
Keep the volume level low enough to be aware of road and traffic conditions.
When Washing Vehicle
Do not expose the equipment, including the speakers to water or excessive moisture. This could cause
electrical shorts, fire or other damage.
When Parked
Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a
chance to cool down before switching the unit on.
Use the Proper Power Supply
This equipment is designed to operate off a 12 volt, negative ground battery system (the normal system
in a North American vehicle.)
Use Authorized Service centers
Do not attempt to disassemble or adjust this precision equipment. Please refer to the Service center list
included with this product for service assistance.
For Installation
The product should be installed in a horizontal position with the front end up at a convenient angle, but
not more than 30˚.
Find the model number and serial number on either the back or bottom of the unit. Please record them
in the space below and retain this booklet as a permanent record of your purchase to aid in
identification in case of theft.
MODEL NUMBER SERIAL NUMBER
DATE PURCHASED FROM
CR-W400U
3
Contents
Use This Equipment Safely...................................................................Page 2
❏
Power and Sound Controls......................................................................4
How to adjust the volume, mute, balance, and tone for best listening
❏
Radio Basics..............................................................................................6
Mode selection, manual and automatic tuning, band selection,
preset stations
❏
Clock Basics..............................................................................................9
Setting the time, selecting the clock display
❏
In case of Malfunction ............................................................................10
❏
Installation Guide....................................................................................11
Step-by-step procedures, electrical connections
❏
Troubleshooting......................................................................................15
Troubleshooting tips, where to get service help
Specifications .............................................................................................17
Part 15 of the FCC Rules............................................................................17
4
Power and Sound Controls
Power
If the vehicle is not running yet, turn the key in the ignition until the
accessory indicator lights.
Press
[PWR] to switch on the power.
Changing Audio Modes
Press this knob [SEL] to change the audio mode as follows.
VOL
a
BASS
a
TRE
(Volume) (Treble)
cd
FADE
b
BAL
(Fader) (Balance)
Volume
●
Press the knob to select the volume mode and then turn it
clockwise or counterclockwise to adjust the volume lev el.
Bass and Treble
Press the knob to select the BASS or TREBLE mode and then turn
it clockwise or counterclockwise to increase or decrease the
bass/treble level.
0 to 40
-12 to 12 -12 to 12
Volume Level
CRW400U
Anti-Volume-Blast Circuit
At power on, the volume returns to the previous level slowly if
the level was at 20 or higher.
CRW400U
CRW400U
d
d
5
Fader
Press the knob to select the FADER mode and then turn it
clockwise or counterclockwise to shift the sound volume to the front
or rear speakers.
Mute
●
Press [MUTE] to mute the sound completely.
●
Press [MUTE] again to cancel.
Note: In the audio mode (BASS/TRE/BAL/FADE), the display
will return to regular operation mode when there is no input for
more than 5 seconds (2 seconds in the VOL mode).
or R 1 to 15
Fader Center
Balance
Press the knob to select the BALANCE mode and then turn it
clockwise or counterclockwise to shift the sound volume to the right
or left speakers.
or L 1 to 15
Balance Center
Power and Sound Controls
(continued)
(F: Front, R: Rear)
Tone Enhancement (Loudness)
●
Press and hold [BAND] (LOUD) for more than 2 seconds to
enhance bass and treble tones when listening at low or medium
volume.
●
Press and hold [BAND] (LOUD) for more than 2 seconds again to
deactivate when listening at higher volumes.
CRW400U
Press and hold
(R: Right, L: Left)
Loading...