Integra DTR-20.1 Owner's Manual

DTR-20.1_En_A.book Page 1 Wednesday, April 8, 2009 10:06 PM

AV Receiver

DTR-20.1

Instruction Manual

DTR-20.1_En_A.book Page 2 Wednesday, April 8, 2009 10:06 PM

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PORTABLE CART WARNIN

S3125A

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is dam-

aged,

B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation.

Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a fluelike gap for warm air to escape.

DTR-20.1_En_A.book Page 3 Wednesday, April 8, 2009 10:06 PM

Precautions

1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the dealer.

3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

Pressing the [On/Standby] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution

Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure War nin g

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by the dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

AT TE NT IO N : POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

DTR-20.1_En_A.book Page 4 Wednesday, April 8, 2009 10:06 PM

Thank you for purchasing an Integra AV receiver. Please read this manual thoroughly before making con-

nections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment

from your new AV receiver. Please retain this manual for future reference.

Supplied Accessories

Make sure you have the following accessories:

Remote controller and two batteries (AA/R6)

Speaker setup microphone

Indoor FM antenna

AM loop antenna

Power cord

(Plug type varies from country to country.)

LEFT

RIGHT

FRONT

SURROUND

LEFT

FRONT

LEFT

FRONT

RIGHT

SURROUND

LEFT

FRONT

LEFT

FRONT

RIGHT

Speaker Cable

LEFT

RIGHT

CENTER

SURROUND

RIGHT

CENTER

SURROUND

RIGHT

LEFT

FRONT HIGH

LEFT

RIGHT

CENTER

SP-B/ZONE2

SURROUND BACK

SP-B/ZONE2

RIGHT

SURROUND BACK

RIGHT

SURROUND BACK

LEFT

SP-B/ZONE2

RIGHT

SP-B/ZONE2

LEFT

SURROUND BACK

RIGHT

CENTER

SURROUND BACK

LEFT

SP-B/ZONE2

LEFT

RIGHT

FRONT HIGH

FRONT WIDE

FRONT HIGH

RIGHT

FRONT WIDE

LEFT

FRONT WIDE

LEFT

FRONT WIDE

RIGHT

FRONT WIDE

RIGHT

FRONT HIGH

RIGHT

FRONT HIGH

LEFT

Speaker cable labels

* In catalogs and on packaging, the letter at the end of the prod-

uct name indicates the color. Specifications and operation are the same regardless of color.

DTR-20.1_En_A.book Page 5 Wednesday, April 8, 2009 10:06 PM

Contents

Introduction

Important Safety Instructions .................................... 2

Precautions ............................................................... 3

Supplied Accessories................................................ 4

Features .................................................................... 6

Multiroom Capability.................................................. 7

Front & Rear Panels.................................................. 8

Front Panel............................................................ 8

Display................................................................. 10

Rear Panel .......................................................... 11

Remote Controller ................................................... 13

Controlling the AV receiver.................................. 13

Installing the Batteries ......................................... 14

Aiming the Remote Controller ............................. 14

About Home Theater............................................... 15

Enjoying Home Theater....................................... 15

Connections

Connecting the AV receiver .................................... 16

Connecting Your Speakers ................................. 16

Connecting Antenna............................................ 19

About AV Connections ........................................ 21

Connecting Audio and Video Signals to the AV

receiver ............................................................. 22

Which Connections Should I Use?...................... 22

Connecting Components with HDMI ................... 23

Connecting a TV or Projector .............................. 25

Connecting a DVD/BD player.............................. 26

Connecting a VCR or DVR for Playback ............. 27

Connecting a VCR or DVR for Recording ........... 28

Connecting a Satellite, Cable, Terrestrial Set-top

box, or Other Video Source .............................. 29

Connecting a CD Player or Turntable ................. 30

Connecting a Cassette, CDR, MiniDisc, or DAT

Recorder ........................................................... 31

Connecting an RI Dock ....................................... 32

Connecting a Dock with the Universal Port

connector .......................................................... 32

Connecting Integra/Onkyo u Components ....... 33

Connecting the Power Cord ................................ 33

Turning On & First Time Setup

Turning On the AV receiver..................................... 34

Turning On and Standby ..................................... 34

First Time Setup...................................................... 35

Audyssey 2EQ™ Room Correction and Speaker

Setup ................................................................ 35

HDMI Input Setup................................................ 38

Component Video Input Setup ............................ 39

Digital Input Setup ............................................... 40

Changing the Input Display ................................. 41

Basic Operations

Basic Operations..................................................... 42

Basic AV receiver Operation ............................... 42

Setting the Display Brightness ............................ 43

Muting the AV receiver ........................................ 43

Using the Sleep Timer......................................... 43

Using Headphones.............................................. 44

Adjusting the Bass & Treble................................ 44

Displaying Source Information ............................ 44

Specifying the Digital Signal Format ................... 45

Listening to the Radio ............................................. 46

AM/FM Frequency Step Setup ............................ 46

Listening to AM/FM Stations ............................... 47

Presetting AM/FM Stations.................................. 49

UP-A1 series Dock for iPod..................................... 50

About the UP-A1 series Dock.............................. 50

Compatible iPod models...................................... 50

Putting Your iPod in the Dock.............................. 50

Function Overview............................................... 50

Controlling iPod ................................................... 51

Recording ................................................................ 53

Using the Listening Modes

Using the Listening Modes ...................................... 54

Selecting the Listening Modes............................. 54

Listening Modes Available for Each Source Format

About the Listening Modes .................................. 59

.... 55

Advanced Setup

Advanced Setup ...................................................... 61

Common Procedures in Setup Menu .................. 61

Speaker Setup..................................................... 61

Audio Adjust Settings .......................................... 64

Source Setup....................................................... 66

Assigning Listening Modes to Input Sources....... 67

Miscellaneous (Volume) Setup............................ 68

Hardware Setup................................................... 69

Lock Setup........................................................... 71

Using the Audio Settings .....................................72

Zone 2

Zone 2 ..................................................................... 74

Connecting Zone 2 ..............................................74

Setting the Zone2 Out ......................................... 74

Using Zone 2 .......................................................75

Using the 12V Triggers........................................ 78

Using the Remote Controller in Zone 2 and

Multiroom Control Kits....................................... 79

Controlling Other Components

Controlling Other Components................................ 80

Preprogrammed Remote Control Codes ............. 80

Entering Remote Control Codes.......................... 80

Resetting the Remote Controller .........................81

Controlling a TV................................................... 82

Controlling a DVD Player, or DVD Recorder ....... 83

Controlling a VCR or PVR ...................................84

Controlling a Satellite Receiver or Cable Receiver

Controlling a CD Player ....................................... 86

Controlling an RI Dock......................................... 87

Controlling a Cassette Recorder ......................... 88

.... 85

Others

Troubleshooting....................................................... 89

Specifications .......................................................... 93

* To reset the AV receiver to its factory defaults, turn it on and,

while holding down the [VCR/DVR] button, press the [On/ Standby] button (see page 89).

15_Introduction_En.fm Page 6 Friday, April 24, 2009 11:04 AM

Features

Amplifier

• 90 Watts/Channel @ 8 ohms (FTC)

• WRAT-Wide Range Amplifier Technology (5Hz–100kHz bandwidth)

• High-Current Low-Impedance Drive

• Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High Power Transformer

Processing

• HDMI ver.1.3a with Repeater System (Deep Color, x.v.Color DTS-HD High Resolution Audio, Dolby TrueHD Dolby Digital Plus, DSD and Multi-CH PCM)

•Direct Mode

• CinemaFILTER

• Non-Scaling Configuration

• A-Form Listening Mode Memory

• Music Optimizer

• 192kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit DSP Processing

, Lip Sync, DTS*2-HD Master Audio,

for Compressed Music

Connections

• 4 HDMI*3 Inputs and 1 Output

• Integra/Onkyo for System Control

• HDTV-Ready Component Video Switching (2 Inputs/1 Output)

• Universal Port for the Dock for iPod* / HD Radio™ Dock

• 4 Digital Inputs (2 Optical/2 Coaxial)

• Zone 2 Pre Out

• IR Input/Output and 12 V Trigger

• RS232 Port for Interface Control

• Banana Plug-compatible Speaker Posts

• Surround Back L/R and Dual Subwoofer Pre Out

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

*2.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark & the DTS logos, Symbol, DTS-HD Master Audio are trademarks of DTS, Inc. ©1996-2008 DTS, Inc. All Rights Reserved.

HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

HD Radio™ and the HD Radio Ready logo are proprietary trademarks of iBiquity Digital Corporation. To receive HD Radio broadcasts, you must install an Onkyo UP-HT1 HD Radio tuner module (sold separately).

*5.

Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending.Audyssey 2EQ™, Audyssey Dynamic Volume™ and Audyssey Dynamic EQ™ are trademarks of Audyssey Laboratories.

Theater-Dimensional is a trademark of Onkyo Corporation.

*7. Music Optimizer™ is a trademark of Onkyo Corporation.

* “Xantech” is a registered trademark of Xantech Corporation. * “Niles” is a registered trademark of Niles Audio Corporation. * Apple and iPod are trademarks of Apple Inc., registered in the

U.S. and other countries.

* “x.v.Color” is a trademark of Sony Corporation.

Miscellaneous

• 40 AM/FM Presets

• Audyssey 2EQ™ lems

• Audyssey Dynamic EQ™

• Audyssey Dynamic Volume™*5 to Maintain Optimal Listening Level and Dynamic Range

• Crossover Adjustment (40/45/50/55/60/70/80/90/100/110/120/130/150/200 Hz)

• A/V Sync Control Function (up to 100 ms)

• Theater Dimensional Virtual Surround Function

• Compatible with RI Dock for iPod

• Preprogrammed u-Compatible Remote

to Correct Room Acoustic Prob-

for Loudness Correction

DTR-20.1_En_A.book Page 7 Wednesday, April 8, 2009 10:06 PM

Multiroom Capability

You can use two speaker systems with this AV receiver—a surround-sound speaker system (up to 7.1 channels) in your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it. And, you can select a different audio source for each room.

Main Room: In your main listening room, you can enjoy up to 7.1-channel playback (see page 15). You can enjoy the various listening modes such as Dolby and DTS (pages 54–60). Zone 2: In your Zone 2 room, you can enjoy 2-channel stereo playback (see page 74). * The listening modes cannot be used with Zone 2.

Main Room

Subwoofer

Front left and right speakers

Center speaker

Zone 2 Room

Surround back left and right speakers

If you use surround back speakers, another power amplifier is necessary (page 18).

Surround left and right speakers

Left and right stereo speakers

If you use Zone 2 speakers, another power amplifier is necessary (page 74).

DTR-20.1_En_A.book Page 8 Wednesday, April 8, 2009 10:06 PM

Front & Rear Panels

Front Panel

e fa b

qpong h i j k l m

tusr

The actual front panel has various logos printed on it. They are not shown here for clarity.

DTR-20.1_En_A.book Page 9 Wednesday, April 8, 2009 10:06 PM

Front & Rear Panels—Continued

The page numbers in parentheses show where you can find the main explanation for each item.

a On/Standby button (34)

Sets the AV receiver to On or Standby.

b Standby indicator (34)

Lights up when the AV receiver is on Standby and flashes while a signal is being received from the remote controller.

c Zone 2 indicator (75)

Flashes when Zone 2 is being set. Lights up when Zone 2 is on.

d [–] & [+] buttons (44)

Used to adjust the tone (bass and treble), and the tone and balance of Zone 2.

Tone button (44)

Used to select either bass or treble.

e Remote-control sensor (14)

Receives control signals from the remote controller.

f Display

See “Display” on page 10.

g Movie/TV button (54)

Selects the listening modes intended for use with movies and TV.

h Music button (54)

Selects the listening modes intended for use with music.

i Game button (54)

Selects the listening modes intended for use with video games.

j Dimmer button (43)

Adjusts the display brightness.

k Memory button (49)

Used when storing or deleting radio presets.

l Tuning Mode button (47)

Selects the Auto or Manual tuning mode for AM and FM radio.

m Display button (44)

Displays various information about the currently selected input source.

n Setup button

Opens and closes the setup menus.

o Tuning, Preset, Arrow, and Enter buttons

When AM or FM is selected, the Tuning [q]/[w] buttons are used for radio tuning, and the Preset [e]/[r] buttons are used to select radio presets (see pages 47, 49). With the setup menus, they work as arrow buttons and are used to select and set items. The [Enter] button is also used with the setup menus.

p Return button

Selects the previously displayed setup menu.

q Master Volume control (42)

Sets the volume of the AV receiver to Min, 1 through 79, or Max.

r Zone 2 and Off buttons (75)

The [Zone 2] button is used to turn on the output of Zone 2. The [Off] button is used to turn off the output of Zone 2.

s Zone 2 Level button (76)

Used when adjusting the volume level of Zone 2.

t Phones jack (44)

This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.

u Input selector buttons (42)

Select the following input sources: DVD/BD, VCR/DVR, CBL/SAT, Game, TV/Tape, Tuner, CD, Port.

v Setup Mic (35)

The Audyssey 2EQ™ Room Correction and Speaker Setup microphone connects here.

DTR-20.1_En_A.book Page 10 Wednesday, April 8, 2009 10:06 PM

Front & Rear Panels—Continued

Display

a bc d

For detailed information, see the pages in parentheses.

a SLEEP indicator (43)

Lights up when the Sleep function has been set.

b MUTING indicator (43)

Flashes while the AV receiver is muted.

c Listening mode and format indicators (54)

Show the selected listening mode and audio input signal format.

d Tuning indicators (47)

FM STEREO (47):

Lights up when tuned to a stereo FM station.

AUTO (47):

Lights up when Auto Tuning mode is selected for AM or FM radio. Goes off when Manual Tuning mode is selected.

TUNED (47):

Lights up when tuned to a radio station.

e Message area

Displays various information.

f Audio input indicators

Indicate the type of audio input that’s selected as the audio source: PCM, MULTI CH, or HDMI.

g Audyssey indicator (36, 63)

Flashes during Audyssey 2EQ™ Room Correction and Speaker Setup. Lights up when the “Equalizer Settings” is set to “Audyssey”.

DTR-20.1_En_A.book Page 11 Wednesday, April 8, 2009 10:06 PM

Front & Rear Panels—Continued

Rear Panel

c d ea g h if

o p q r tvw xus

a DIGITAL IN COAXIAL 1 and 2

These coaxial digital audio inputs are for connecting components with a coaxial digital audio output, such as a CD player or DVD/BD player. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 40.

b DIGITAL IN OPTICAL 1 and 2

These optical digital audio inputs are for connecting components with an optical digital audio output, such as a CD player or DVD/BD player. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 40.

c COMPONENT VIDEO IN 1 and 2

These RCA component video inputs are for connecting components with a component video output, such as a DVD/BD player, DVD/BD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Component Video Input Setup” on page 39.

d COMPONENT VIDEO OUT

This RCA component video output is for connecting a TV or projector with a component video input.

e HDMI IN 1–4 and OUT

f AM and FM ANTENNA

g ETHERNET

h MONITOR OUT

i UNIVERSAL PORT

HDMI (High Definition Multimedia Interface) connections carry digital audio and digital video. The HDMI inputs are for connecting components with an HDMI output, such as a DVD/BD player, DVD/BD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “HDMI Input Setup” on page 38. The HDMI outputs are for connecting a TV or projector with an HDMI input.

The AM push terminals are for connecting an AM antenna. The FM jack is for connecting an FM antenna.

This port is for connecting the AV receiver to home automation equipment and external controllers.

The composite video jack should be connected to a video input on your TV or projector.

This jack is for connecting the component with the Universal Port connector such as UP-A1 series Dock.

DTR-20.1_En_A.book Page 12 Wednesday, April 8, 2009 10:06 PM

Front & Rear Panels—Continued

j IR IN A/B and OUT

A commercially available IR receiver can be connected to the IR IN A or B jack, allowing you to control the AV receiver while you’re in Zone 2, or control it when it’s out of sight, for example, installed in a cabinet. A commercially available IR emitter can be connected to the IR OUT jack to pass IR (infrared) remote control signals through to other components.

k 12V TRIGGER OUT (A/B/C)

This output can be connected to the 12-volt trigger input on a component in Zone 2.

l RS232

This is the RS232 port.

m PRE OUT: ZONE 2 L/R

This analog audio output can be connected to a line input on an integrated amplifier in Zone 2. See “Connecting Zone 2” on page 74.

n AC INLET

The supplied power cord is connected here. The other end of the power cord should be connected to a suitable wall outlet.

o u REMOTE CONTROL

This u (Remote Interactive) jack can be connected to the u jack on another u-capable Integra/Onkyo component for remote and system control. To use u, you must make an analog audio connection (RCA) between the AV receiver and the other component, even if they are connected digitally.

p CD IN

This analog audio input is for connecting a CD player’s analog audio output.

q TV/TAPE IN/OUT

These analog audio input and output jacks are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder, etc.

r GAME IN

Here you can connect a game console, etc. Input jacks include composite video and analog audio.

s CBL/SAT IN

A cable or satellite receiver can be connected here. There is composite video input jack for connecting the video signal, and there are analog audio input jacks for connecting the audio signal.

t VCR/DVR IN/OUT

A video component, such as a VCR or DVR, can be connected here for recording and playback. There is composite video input and output jack for connecting the video signal, and there are analog audio input jacks for connecting the audio signal.

u DVD/BD IN

This input is for connecting a DVD/BD player. There is composite video input jack for connecting the video signal.

v SUBWOOFER PRE OUT

This analog audio output can be connected to a powered subwoofer. The same signal is output from each jack.

w PRE OUT: SURR BACK L/R

This analog audio output can be connected to the analog audio input on another power amplifier.

x FRONT L/R, CENTER, and SURR L/R

SPEAKERS

These terminal posts are for connecting the front speakers, center, and surround speakers.

See pages 16–33 for hookup information.

DTR-20.1_En_A.book Page 13 Wednesday, April 8, 2009 10:06 PM

Remote Controller

Controlling the AV receiver

To control the AV receiver, press the [Receiver] button to select Receiver mode.

You can also use the remote controller to control your DVD/BD player, CD player, and other components. See page 80 for more details.

j k

d Setup button

Used to change settings.

e Listening Mode buttons (54)

Used to select the listening modes.

f Dimmer button (43)

Adjusts the display brightness.

g Display button (44)

Displays information about the current input source.

h Muting button (43)

Mutes or unmutes the AV receiver.

i VOL [q]/[w] button (42)

Adjusts the volume of the AV receiver regardless of the currently selected remote controller mode.

j Return button

Returns to the previous display when changing settings.

k Audio button (72)

Used to change audio settings. When the “AudioTVOut” setting is set to “On” (page 69), this button is disabled.

l Sleep button (43)

Used with the Sleep function.

■ Controlling the tuner

To control the AV receiver’s tuner, press the [Tuner] (or [Receiver]) button. You can select AM or FM by pressing the [Tuner] button repeatedly.

For detailed information, see the pages in parentheses.

a On/Standby button (34)

Sets the AV receiver to On or Standby.

b Remote Mode/Input Selector buttons (42, 51,

82–88)

Selects the remote controller modes and the input sources.

c Arrow [q]/[w]/[e]/[r] and Enter buttons

Used to select and adjust settings.

1 Arrow [q]/[w] buttons

Used to tune into radio stations.

2 D.TUN button (48)

Selects the Direct tuning mode.

3 Display button (48)

Displays information about the band, frequency, preset number, and so on.

4 CH +/– button (49)

Selects radio presets.

5 Number buttons (48)

Used to select radio stations directly in the Direct tuning mode. Also you can select a preset directly.

Note:

An Onkyo cassette recorder connected via u can also be controlled in Receiver mode (see page 88).

DTR-20.1_En_A.book Page 14 Wednesday, April 8, 2009 10:06 PM

Remote Controller—Continued

Installing the Batteries

To open the battery compartment, press

the small lever and remove the cover.

Insert the two supplied batteries (AA/R6)

in accordance with the polarity diagram inside the battery compartment.

Replace the cover and push it shut.

Notes:

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.

Aiming the Remote Controller

When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below.

Remote control sensor

Standby indicator

Notes:

• The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing.

• If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

• Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries.

• The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.

• The remote controller will not work if there’s an obstacle between it and the AV receiver’s remote control sensor.

• When the remote control codes have been registered and you want to operate another component (page 80), or when you want to operate an Integra/Onkyo component without u connection, point the remote controller at the other component to use it.

• When you want to operate an Integra/Onkyo component with u connection or an -compatible component connected via HDMI (pages 82, 83), point the remote controller at the AV receiver’s remote control sensor.

AV r ecei ve r

Approx. 16 ft. (5 m)

DTR-20.1_En_A.book Page 15 Wednesday, April 8, 2009 10:06 PM

About Home Theater

Enjoying Home Theater

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring Dolby Digital or DTS. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes.

Front left and right speakers

These output the main sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex.

Center speaker

This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. For movies it’s used mainly for dialog. Position it close to your TV (preferably on top) facing forward at about ear level, or at the same height as the front left and right speakers.

Subwoofer

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the way along the front wall, as shown. You can connect the powered subwoofer with two SUBWOOFER PREOUT jacks respectively. Tip: To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room and choose the one that provides the most satisfying results.

Surround back left and right speakers

These speakers are necessary to enjoy Dolby Digital EX, DTS-ES Matrix, DTS-ES Discrete, etc. They enhance the realism of surround sound and improve sound localization behind the listener. Position them behind the listener about 2–3 feet (60–100 cm) above ear level.

Surround left and right speakers

These speakers are used for precise sound pos itioning and to add realistic ambience. Position them at the sides of the listener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally they should be equally spaced from the listener.

1/3 of wall position

Corner position

DTR-20.1_En_A.book Page 16 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver

Connecting Your Speakers

Speaker Configuration

For 7.1-channel surround-sound playback, you need seven speakers and a powered subwoofer.

The following table shows which channels you should use based on the number of speakers you have.

Number of speakers: 2 3 4 5 6 7

Front left ✓✓✓✓✓✓

Front right ✓✓✓✓✓✓

Center ✓✓✓✓

Surround left ✓✓✓✓

Surround right ✓✓✓✓

Surround back* ✓

Surround back left ✓

Surround back right ✓

* If you’re using only one surround back speaker, connect it to the

power amplifier’s left terminals.

No matter how many speakers you use, a powered subwoofer is recommended for a powerful and solid bass. If you use surround back speakers, another power amplifier is necessary (page 18). To get the best from your surround-sound system, you must set the speaker settings. You can do this automatically (see page 35) or manually (see page 61).

Attaching the Speaker Labels

The AV receiver’s positive (+) speaker terminals are all red. (The negative (–) speaker terminals are all black.)

Speaker Color

Front left White

Front right Red

Center Green

Surround left Blue

Surround right Gray

Surround back left Brown

Surround back right Tan

The supplied speaker labels are color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. All you need to do then is to match the color of each label to the corresponding speaker terminal.

Using Dipole Speakers

You can use dipole speakers for the surround left and right and surround back left and right speakers. Dipole speakers output the same sound in two directions.

Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround left and right dipole speakers should be positioned so that their arrows point toward your TV or screen, while the surround back left and right dipolar speakers should be positioned so that their arrows point toward each other, as shown.

If you use surround back speakers, another power amplifier is necessary (page 18).

Dipole speakers

TV/screen

7 8

1. Subwoofer

2. Front left speaker

3. Center speaker

4. Front right speaker

5. Surround left speaker

Normal speakers

TV/screen

6. Surround right speaker

7. Surround back left speaker

8. Surround back right speaker

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver’s PRE OUT: SUBWOOFER to the input on your powered subwoofer. If your subwoofer is unpowered and you’re using an external amplifier, connect the PRE OUT: SUBWOOFER to the amp’s input. You can connect the powered subwoofer with two SUBWOOFER PREOUT jacks respectively. The same signal is output from each jack.

Powered

subwoofer

LINE INPUT

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

LINE INPUT

DTR-20.1_En_A.book Page 17 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. Connect positive (+) terminals to only positive (+) terminals, and negative (–) terminals to only negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect a speaker to several terminals.

Connecting the Speaker Cables

Terminal posts

Strip 1/2"-5/8" (12-

15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

Unscrew the terminal.

Fully insert the bare wire.

Screw the terminal tight.

1/2"-5/8" (12-15mm)

DTR-20.1_En_A.book Page 18 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

The following illustration shows which speaker should be connected to each pair of terminals for 7.1-channel playback. If you’re using only one surround back speaker, connect it to the power amplifier’s left terminals.

Surround right

speaker

Center

speaker

Surround

back right

speaker

AUDI O INPUT

Power amplifier

Surround

back left speaker

Front right

speaker

Surround left

speaker

Front left

speaker

Connect your Power amplifier’s analog audio output jacks to the AV receiver’s PRE OUT:SURR BACK L/R jacks with an audio cable.

Note:

The speakers are configured by using “Speaker Setup” on page 61.

DTR-20.1_En_A.book Page 19 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting Antenna

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

AM ANTENNA push terminals

FM ANTENNA jack

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

Attach the FM antenna, as shown.

Insert the plug fully into the jack.

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

Assemble the AM loop antenna, inserting

the tabs into the base, as shown.

Connect both wires of the AM loop

antenna to the AM push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around.)

Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

Push Insert wire Release

Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

Use thumbtacks or something similar to

fix the FM antenna into position.

Thumbtacks, etc.

Caution: Be careful that you don’t injure yourself when using thumbtacks.

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 20).

Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 20).

DTR-20.1_En_A.book Page 20 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting an Outdoor FM Antenna

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

Notes:

• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.

• For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.

• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.

• For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.

• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

Connecting an Outdoor AM Antenna

If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.

Outdoor antenna

AM loop antenna

Outdoor AM antennas work best when installed horizontally outside, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected. Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

Insulated antenna cable

■ Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.

TV/FM antenna splitter

To AV r e c e iv e r To T V (o r VC R )

DTR-20.1_En_A.book Page 21 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

About AV Connections

• Before making any AV connections, read the manuals supplied with your other AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

Optical Digital Jacks

The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution: To prevent shutter damage, hold the optical plug straight when inserting and removing.

AV Cables and Jacks

Video / Audio

Cable Jack Description

HDMI

AV Connection Color Coding

RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect rightchannel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.

Left (white)

Right (red) Right (red)

(Yellow)

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

HDMI

HDMI connections can carry uncompressed standard- or high-definition digital video and audio and offer the best picture and sound quality.

Analog audio

Composite video

Left (white)

(Yellow)

Right!

Wrong!

Video

Component video cable

Composite video cable

Audio

Optical digital audio cable

Coaxial digital audio cable

Analog audio cable (RCA)

B/CB

PR/CR

B/CB

PR/CR

CB/P

CR/P

OPTICAL

COAXIAL

Note: The AV receiver does not support SCART connections.

Component video separates the luminance (Y) and color difference signals (P

R, PB), providing the best

picture quality. (Some TV manufacturers label their component video jacks slightly differently.)

Composite video is commonly used on TVs, VCRs, and other video equipment.

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for coaxial.

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for optical.

This cable carries analog audio. It’s the most common connection format for analog audio and can be found on virtually all AV components.

DTR-20.1_En_A.book Page 22 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting Audio and Video Signals to the AV receiver

By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver.

: Signal Flow

Video

Audio

DVD player, etc.

Speakers (see page 18 for hookup details)

Video

Audio

TV, projector,

etc.

Which Connections Should I Use?

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide.

Video Signal Flow Chart

Video Connection Formats

Video equipment can be connected to the AV receiver by using any one of the following video connection formats: composite video, component video, or HDMI, the latter offering the best picture quality.

When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats, so only outputs of the same format as the input will output the signal.

DVD player, etc.

AV receiver

Composite

Composite Component

Component

MONITOR OUT

HDMI

TV, projector, etc.

Audio Connection Formats

Audio Signal Flow Chart

DVD player, etc.

Audio equipment can be connected to the AV receiver by using any of the following audio connection formats: analog, optical, coaxial, or HDMI.

When you connect audio equipment to an HDMI, OPTICAL, or COAXIAL input, you must assign that input to an input selector (see pages 38 and 40).

AV receiver

TV, projector, etc.

Analog

Depends on the “AudioTVOut” setting (see page 69) and Digital Input Setup (see page 40). And, the audio signal can be output only when the input video signal is from HDMI IN. Do not connect the optical or coaxial audio cable when you want to output the analog audio signal.

Optical Coaxial HDMI

OUT

If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, digital, analog.

HDMI

DTR-20.1_En_A.book Page 23 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting Components with HDMI

About HDMI

Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital audio, or multichannel PCM).

The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface),*1 so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.) The AV receiver uses HDCP (High-bandwidth Digital Content Protection), so only HDCP-compatible components will display a picture.

The AV receiver’s HDMI interface is based on the following standard:

Deep Color, x.v. Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multichannel PCM

Supported Audio Formats

• 2-channel linear PCM (16/20/24 bit/32–192kHz)

• Multichannel linear PCM (7.1 ch, 32–192kHz)

• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD Master Audio)

Your DVD player must be able to output these formats from its HDMI OUT.

■ Integra/Onkyo for System Control

, which stands for Remote Interactive over HDMI, is the name of the system control function found on Integra/Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than -compatible components cannot be guaranteed.

• Set “HDMI Ctrl” to “On” (page 70).

• See “Controlling a TV” (page 82) and “Controlling a DVD Player, or DVD Recorder” (page 83) for operation.

Note:

Do not connect the -compatible component more than the following number to the HDMI input terminal so that the linked operations work properly.

• DVD/BD player is up to three.

• DVD/BD recorder is up to three.

• Cable/Satellite Set-top box is up to four.

Do not connect the AV receiver to the other AV receiver /AV amplifier via HDMI. When the -compatible component more than the above-mentioned is connected, the linked operations are not

guaranteed.

About Copyright Protection

The AV receiver supports HDCP (High-bandwidth Digital Content Protection),*2 a copy-protection system for digital video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999. *2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to

protect video content and requires a HDCP-compatible device to display the encrypted video.

*3 DDWG (Digital Display Working Group): Led by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open

industry group’s objective is to address the industry's requirements for a digital connectivity specification for high-performance PCs and digital displays.

DTR-20.1_En_A.book Page 24 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Making HDMI Connections

Step 1:

Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD/BD player, TV, projector, and so on.

Step 2:

Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 38).

■ Video Signals

Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV.

■ Audio Signals

Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV receiver. Normally, they are not output by the HDMI OUT, unless the “AudioTVOut” setting is set to “On” (see page 69).

Hint!

To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the “AudioTVOut” setting to “On” (see page 69), and set your DVD player’s HDMI audio output setting to PCM.

DVD/BD player

HDMI

ASSIGNABLE

HDMI

OUT

HDMI

Notes:

• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.

• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.

• When the “AudioTVOut” setting is set to “On” (see page 69), or “TV Ctrl” is set to “On” (see page 70) and you’re listening through your TV’s speakers, if you turn up the AV receiver volume control, the sound will be output by the AV receiver’s speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for details.

DTR-20.1_En_A.book Page 25 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting a TV or Projector

Step 1: Video Connection

Choose a video connection that matches your TV ( or ), and then make the connection.

Step 2: Audio Connection

Choose an audio connection that matches your TV ( , , or ), and then make the connection.

A B

a b c

• With connection , you can listen to and record audio from your TV or listen in Zone 2.

• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 as well, use and , or and .)

b c a b a

Connection AV receiver Signal flow TV

COMPONENT VIDEO OUT ⇒ Component video input

MONITOR OUT V ⇒ Composite video input

TV/TAPE IN L/R ⇐ Analog audio L/R output

DIGITAL IN COAXIAL 2 (CBL/SAT) ⇐ Digital coaxial output

DIGITAL IN OPTICAL 1 (GAME) ⇐ Digital optical output

Connect one or the other Connection must be

b c

assigned (see page 40)

If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver

Hint!

to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see pages 27 and

29).

OPTICAL

OUT

YCOAXIAL

R AUDI O

COMPONENT VIDEO IN

TV, projector,

etc.

OUT

VIDEO

DTR-20.1_En_A.book Page 26 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting a DVD/BD player

Step 1: Video Connection

Choose a video connection that matches your DVD/BD player ( or You must connect the AV receiver to your TV with the same type of connection.

Step 2: Audio Connection

Choose an audio connection that matches your DVD/BD player ( , , or ), and then make the connection.

), and then make the connection.

A B

a b c

• With connection , you can listen to and record audio from a DVD or listen in Zone 2.

• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 as well, use and , or and .)

b c a b a

• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left and right outputs for connection .

Connection AV receiver Signal flow DVD/BD player

COMPONENT VIDEO IN 1 (DVD/BD) ⇐ Component video output

DVD/BD IN V ⇐ Composite video output

DVD/BD IN L/R ⇐ Analog audio L/R output

DIGITAL IN COAXIAL 1 (DVD/BD) ⇐ Digital coaxial output

DIGITAL IN OPTICAL 1 (GAME) ⇐ Digital optical output

OPTICAL

OUT

Connect one or the other Connection must be

assigned (see page 40)

OUT

Y COAXIAL

COMPONENT VIDEO OUT

L R

AUDI O

OUT

DVD/BD player

VIDEO

OUT

DTR-20.1_En_A.book Page 27 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting a VCR or DVR for Playback

Hint!

With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV receiver, useful if your TV has no audio outputs.

Step 1: Video Connection

Choose a video connection that matches your VCR or DVR ( or

), and then make the connection. You must

A B

connect the AV receiver to your TV with the same type of connection.

Step 2: Audio Connection

Choose an audio connection that matches your VCR or DVR ( , , or ), and then make the connection.

• With connection , you can listen to the VCR or DVR even in Zone 2.

• To enjoy Dolby Digital and DTS, use connection or . (To listen in Zone 2 as well, use and , or and .)

Connection AV receiver Signal flow VCR or DVR

b c a b a c

COMPONENT VIDEO IN 1 (DVD/BD) ⇐ Component video output

VCR/DVR IN V ⇐ Composite video output

VCR/DVR IN L/R ⇐ Analog audio L/R output

DIGITAL IN COAXIAL 1 (DVD/BD) ⇐ Digital coaxial output

DIGITAL IN OPTICAL 1 (GAME) ⇐ Digital optical output

a b c

OPTICAL

OUT

Connect one or the other Connection must be

b c

assigned (see page 40)

OUT

YCOAXIAL

R AUDIO

COMPONENT VIDEO OUT

OUT

VCR, DVR

VIDEO

OUT

DTR-20.1_En_A.book Page 28 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting a VCR or DVR for Recording

Step 1: Video Connection

Make the video connection . The video source to be recorded must be connected to the AV receiver via the same type of connection.

Step 2: Audio Connection

Make the audio connection .

Connection AV receiver Signal flow VCR or DVR

VCR/DVR OUT V ⇒ Composite video input

VCR/DVR OUT L/R ⇒ Audio L/R input

L R

AUDI O

VCR, DVR

Notes:

• The AV receiver must be turned on for recording. Recording is not possible while it’s on Standby.

• If you want to record directly from your TV or another video source without going through the AV receiver, connect the audio and video outputs from your TV or other video component directly to the recording VCR/DVR’s audio and video inputs. See the manuals supplied with your TV or VCR/DVR for details.

• Video signals connected to composite video inputs can only be recorded via composite video outputs. If your TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output.

VIDEO

DTR-20.1_En_A.book Page 29 Wednesday, April 8, 2009 10:06 PM

Connecting the AV receiver—Continued

Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source

Hint!

With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, which is useful if your TV has no audio outputs.

Step 1: Video Connection

Choose a video connection that matches the video source ( or

), and then make the connection.

A B

You must connect the AV receiver to your TV with the same type of connection.

Step 2: Audio Connection

Choose an audio connection that matches the video source ( , , or ), and then make the connection.

• With connection , you can listen to and record audio from the video source or listen in Zone 2.

• To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2 as well, use and , or and .)

Connection AV receiver Signal flow Video source

b c a b a

COMPONENT VIDEO IN 2 (CBL/SAT) ⇐ Component video output

CBL/SAT IN V ⇐ Composite video output

CBL/SAT IN L/R ⇐ Analog audio L/R output

DIGITAL IN COAXIAL 2 (CBL/SAT) ⇐ Digital coaxial output

DIGITAL IN OPTICAL 1 (GAME) ⇐ Digital optical output

a b c

OPTICAL

Connect one or the other Connection must be assigned (see page 40)

OUT

YCOAXIAL

COMPONENT VIDEO OUT

AUDI O

OUT

Satellite, cable, set-top box, etc.

VIDEO

OUT

+ 67 hidden pages