INGENICO ICT250 User Manual

U s e r G u i d e

Product name : iCT220/iCT250

Range : COUNTER TOP

INGENICO – 192 avenue Charles de Gaulle – 92200 Neuilly sur Seine FRANCE Tél. [phone] Fax [phone]

www.ingenico.com

Contents

1.Introduction __________________________________________________3

2.Unpacking____________________________________________________3

3.Recommendations ____________________________________________ 4

3.1.Security _____________________________________________________________4

3.2.Telephone emergency, hanging up _______________________________________4

3.3.Security of your terminal _______________________________________________5

3.4.Standard compliance marking ___________________________________________5

3.5.FCC compliance _______________________________________________________5

3.6.Main Characteristics ___________________________________________________ 7

4.Installation and connection_____________________________________ 8

4.1.Positioning the terminal ________________________________________________8

4.2.Connections__________________________________________________________8

4.3.Installing the iCT220/iCT250 – Cable fixing__________________________________8

4.3.1.Opening the cable cover_________________________________________________________ 8

4.3.2.Kit Magic Box installation ________________________________________________________ 9

4.3.3.Connect cables _______________________________________________________________ 10

4.3.4.Close cover ___________________________________________________________________ 11

4.4.Installation of the Magic Box ___________________________________________ 11

4.5.Installing SAM (Secure access module) ___________________________________ 12

4.6.Installing MicroSD Card (optional) _______________________________________ 13

5.Installing a paper roll __________________________________________ 14

6.Daily use ____________________________________________________ 15

6.1.Keypad functions ____________________________________________________ 15

6.2.Adjusting the contrast ________________________________________________ 15

6.3.Card insertion _______________________________________________________ 16

6.3.1.Swiping a card ________________________________________________________________ 16

6.3.2.Inserting a chip card ___________________________________________________________ 16

6.3.3.Inserting a chip card in second reader (Optional) ____________________________________ 16

6.3.4.Reading Contactless (Optional) __________________________________________________ 16

7.Maintenance_________________________________________________ 18

7.1.Paper roll ___________________________________________________________ 18

7.2.Cleaning of the terminal _______________________________________________ 19

7.3.Transport and storage ________________________________________________ 19

7.4.Troubleshooting _____________________________________________________ 19

7.5.End of life___________________________________________________________20

Product name : iCT220/iCT250 •	2/21	Copyright © 2009 Ingenico
900002734 R11 000 01/1021
296114093		All rights reserved

1. Introduction

Thank you for choosing an Ingenico payment terminal.

We recommend you to read carefully this user guide: It gives you the necessary information about safety precautions, unpacking, installation, and maintenance of your terminal.

CAUTION

To benefit from the guarantee related product, and to respect the security, we ask you to use only the power supply delivered in box with the product, entrusting maintenance operations only to an authorized person.

Failure to comply with these instructions will void the manufacturer’s responsibility.

2. Unpacking

ADVICE

Carefully preserve the packaging of the iCT220/iCT250. It must be re used whenever the terminal is shipped.

According to the model, the following items are included in the iCT220/iCT250 box

•The iCT220/iCT250 terminal equipped with its paper roll

•Magic box ( mandatory use )

•The main power supply with its cable connection (according to the national needs).

•The cable connection for the telephone network

•This installation guide

		Wall mounted
User guide	Magic box	power supply unit
		Cable connection for the
		telephone network

Desktop power supply unit provided (mandatory) with iCT equipped with the following options:

• Contactless model

iCT220/iCT250 terminal

CAUTION

The power supply unit provided with your equipment is specially designed for Ingenico iCT220/iCT250 terminals. Do not use any other power supply.

Product name : iCT220/iCT250 •	3/21	Copyright © 2009 Ingenico
900002734 R11 000 01/1021
296114093		All rights reserved

3. Recommendations

3.1.Security

Power on/Power down

To power on or power down the iCT220/iCT250 connect or disconnect the power supply from the electric outlet.

Lithium battery

The iCT220/iCT250 is fitted with a lithium battery which is not accessible to the user. Only a qualified technician may be authorized to open the unit and change this component.

Electrical power supply network

Provide an electrical outlet :

located near the equipment and easily accessible

which meets the standards and regulations in the country of use.

Telephone network

Provide a phone jack complying with standards and regulations in the country of use.

SAM/SIM or SD Memory Card compartment cover

Located under the terminal, it must be in place during normal operation of the terminal.

Cable compartment cover

The cable compartment cover is located under the terminal, it must be in place during normal operation of the terminal.

3.2. Telephone emergency, hanging up

You have an urgent call to make, when iCT220/iCT250 hangs on the line. In order to get a dial tone…

Place the handset in the hang up position and :

	press the red key (=cancel)
or	disconnect the power supply from the mains network
or	disconnect the iCT220/iCT250 telephone connector from the telephone call socket,
	and place the telephone connector into the telephone wall socket.

You will have a dial tone within 6 seconds.

Product name : iCT220/iCT250 •	4/21	Copyright © 2009 Ingenico
900002734 R11 000 01/1021
296114093		All rights reserved

3.3. Security of your terminal

Upon receipt of your terminal you should check for signs of tampering of the equipment. It is strongly advised that these checks are performed regularly after receipt. You should check, for example: that the keypad is firmly in place; that there is no evidence of unusual wires that have been connected to any ports on your terminal or associated equipment, the chip card reader, or any other part of your terminal. Such checks would provide warning of any unauthorised modifications to your terminal, and other suspicious behaviour of individuals that have access to your terminal. Your terminal detects any “tampered state”. In this state the terminal will repeatedly flash the message” Alert Irruption!” and further use of the terminal will not be possible. If you observe the “Alert Irruption!” message, you should contact the terminal helpdesk immediately.

You are strongly advised to ensure that privileged access to your terminal is only granted to staff that have been independently verified as being trustworthy.

CAUTION

NEVER ask the customer to divulge their PIN Code. Customers should be advised to ensure that they are not being overlooked when entering their PIN Code.

3.4. Standard compliance marking

iCT220

•This class (B) digital apparatus complies with Canadian ICES 003

iCT220 / iCT250

•conforms to the following standards and rules :

–IEC 60950 1 2nd Ed: Electrical safety of data processing equipment including electrical office equipment

–FCC part 15 C (ICT250 ), FCC part 15 B(ICT220 )

–FCC part 68

–EN 55024: Data processing equipment – Immunity characteristics Limits and measurement methods. Issue 1998 + A1 2001 + A2 2003

3.5. FCC compliance

FCC ID : XKB ICT220 / XKB ICT250

This equipment as been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with instruction, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct interface by one more of the following measures :

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into a outlet on circuit different from that to which the receiver is connected.

Product name : iCT220/iCT250 •	5/21	Copyright © 2009 Ingenico
900002734 R11 000 01/1021
296114093		All rights reserved

•Consult the dealer or an experience radio/TV technician for help.

Part 68 of FCC Rules

US : IEOMM01BICT220 / IEOMM01BICT250

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

This equipment uses the following USOC jacks: (RJ11C).

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, please contact INGENICO, or your local INGENICO distributor or service center in the U.S.A. for repair and/or warrant information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

CAUTION

The user is cautioned that any changes or modification not approved by INGENICO could void user’s authority to operate the equipment.

Product name : iCT220/iCT250 •	6/21	Copyright © 2009 Ingenico
900002734 R11 000 01/1021
296114093		All rights reserved

3.6. Main Characteristics

Terminal

	Weight		about 325 g to 350 g full option
	Size		185 x 83 x 63 mm (l x w x h)

Power supply unit (wall mounted)

	Weight		approx 115 g (without mains cable)
	Size		approx 77 x 25 x 89 mm (L x w x h)
	Class		Class II equipment
	Input voltage		120V 60Hz
	Max consumption		400 mA

The power supply unit is especially designed by the manufacturer for its terminals and so must be used.

Desktop power supply unit

Weight	approx 230 g (without mains cable)
Size	approx 98 x 50 x 30 mm (L x w x h)
Class	Class II equipment
Input voltage	100 240VCA 50 60 Hz
Max consumption	800 mA

Cable length

	Power block cable		approx 1,8 m
	Telephone cable		approx 3 m

Product name : iCT220/iCT250 •	7/21	Copyright © 2009 Ingenico
900002734 R11 000 01/1021
296114093		All rights reserved