IBM storage products
Quick installation guide
Ultrastar 36XP
Multi-mode SE/LVD
Models: DRHS-36V
DRHS-36D
Handling precautions
1.Always handle the drive with care to prevent damage from shock, vibration, or electrostatic discharge (ESD).
2.Do not open the static-protective bag containing the drive until required. Static electricity can damage the drive.
3.Always handle the drive with care to prevent damage from shock, vibration, or electrostatic discharge (ESD).
4.Do not open the static-protective bag containing the drive until required. Static electricity can damage the drive.
5.Turn off and unplug your computer. Remove case.
6.When you are installing the drive, touch the
static-protective package containing the drive to a grounded, unpainted metal surface for at least two seconds. (This drains static electricity from the package and from your body.)
7.Handle the drive carefully by the edges. Do not touch any exposed printed circuit board.
8.Save your drive packaging materials including the ESD bag in the event that the drive must be returned. Place the drive in an anti-static bag before placing it in the shipping container. The warranty will be void if the drive is not returned in IBM approved packaging.
Installation procedure
It is advisable to back up all data before proceeding with the installation.
This procedure may require the use of a bootable System Diskette containing FDISK.COM and FORMAT.COM
Setting the address
1.Each drive on the SCSI bus must have a unique address. Sixty eight and eighty pin (Wide SCSI) devices have 16 possible addresses.
2.SCSI address bits 3,2,1, and 0 of the 32 pin Option Jumper Block are used to select the SCSI device ID.
|
|
|
|
|
|
|
|
|
|
Force Single Ended Mode |
||
|
|
External Activity LED Write Protect |
|
|
||||||||
|
|
|
|
Ground |
|
|
Auto Start Delay |
|
||||
|
|
Auto Start |
|
|
|
|
Disable Sync Negotiations |
|||||
|
|
|
Blank |
|
Reserved |
|
Disable SCSI Parity |
|||||
|
SCSI ID |
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
Disable Unit Attention |
||||
3 |
Bits |
|
|
|
|
|
|
|
|
|
Disable Wide |
|
2 |
1 |
0 |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
Negotiations |
1 |
3 |
5 |
7 |
|
11 13 15 |
17 19 |
21 |
23 25 27 29 |
31 |
|||
2 |
4 |
6 |
8 |
10 |
12 |
14 |
16 18 20 22 |
24 26 28 |
30 |
32 |
||
Ground |
|
Ground |
|
+5V |
|
Ground |
|
Termination |
||||
|
|
|
|
Reserved |
|
|
|
|
Power Enable |
|||
|
|
|
|
|
|
|
|
|
||||
Note: In the table below, “off” means a jumper is not in place and “on” means a jumper is in place.
Bit 3 |
Bit 2 |
Bit 1 |
Bit 0 |
Address |
off |
off |
off |
off |
0 |
off |
off |
off |
on |
1 |
off |
off |
on |
off |
2 |
off |
off |
on |
on |
3 |
off |
on |
off |
off |
4 |
off |
on |
off |
on |
5 |
off |
on |
on |
off |
6 |
off |
on |
on |
on |
7 |
on |
off |
off |
off |
8 |
on |
off |
off |
on |
9 |
on |
off |
on |
off |
10 |
on |
off |
on |
on |
11 |
on |
on |
off |
off |
12 |
on |
on |
off |
on |
13 |
on |
on |
on |
off |
14 |
on |
on |
on |
on |
15 |
|
Page 1 |
IBM Hard Disk Drive Technical Support Center |
version 2.0 |
Loading...