Humax HD-FOX IR User Manual

Download

HD Digital Receiver

The default password is 0000.

User’s Manual

HD-FOX IR

Notice

Thank you for purchasing a HUMAX product. Please read this user’s manual carefully to be able to safely install, use and maintain the product at maximum performance. Keep this user’s manual next to your product for future reference. The information in this user’s manual is subject to change without notice.

Not to be copied, used or translated in part or whole without HUMAX’s prior consent in writing except approval of ownership of copyright and copyright law.

Warranty

The warranty does not cover parts which may become defective due to misuse of the information contained in this manual.

Trademarks

• Irdeto is a trademark of Irdeto Access B.V.

• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

GB1

User’s Manual

Notice

Warnings, Cautions and Notes

Throughout the whole manual, pay special attention to the following marks that indicate hazardous situations.

• Warning

Indicates a hazardous situation which could result in serious injury.

• Caution

Indicates a situation which could damage the equipment or other apparatus.

• Note

Indicates additional information to make the user aware of possible problems and information of any

importance to help understand, use and maintain the installation.

Meaning of Symbols

To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualied service personnel.

This symbol indicates dangerous voltage inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Instruction about the ‘WEEE’ Symbol

This product should not be disposed with other household wastes at the end of its working life. Please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. This will prevent possible harm to the environment or human health from uncontrolled waste disposal.

• Domestic users:

Please contact either the retailer where you purchased this product or their local government oce

for details of where and how they can take this item for environmentally safe recycling.

• Business users:

Contact your supplier and check the terms and conditions of the purchase contract. This product

should not be mixed with other commercial wastes for disposal.

GB2

User’s Manual

Safety Warning

This product has been manufactured to comply with international safety standards. Please read the following safety precautions carefully.

Safety Instructions and Precautions

1. MAINS SUPPLY

90-250V a.c., 50/60Hz

• Operate this product only from the type of power supply indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your local power company.

• Disconnect the product from the mains before you start any maintenance or installation procedures.

2. OVERLOADING

• Do not overload a wall outlet, extension cord or adapter as this may result in electric re or shock.

3. LIQUID

• The product should not be exposed to liquid of any kind. In addition, no objects lled with liquid should be placed on the apparatus.

4. CLEANING

• Disconnect the product from the wall outlet before cleaning.

• Use a light damp cloth (no solvents) to dust the product.

5. VENTILATION

• The slots on top of the product must be left uncovered to allow proper airow into the unit.

• Do not stand the product on soft furnishings or carpets.

• Do not stack electronic equipments on top of the product.

6. ATTACHMENTS

• Do not use any unsupported attachments as these may be hazardous or cause damage to the product.

7. CONNECTION TO THE SATELLITE DISH LNB

• Disconnect the product from the mains before connecting or disconnecting the cable from the satellite dish. Failure to do so can damage the LNB.

8. CONNECTION TO THE TV

• Disconnect the product from the mains before connecting or disconnecting the cable from the TV. Failure to do so can damage the TV.

9. EARTHING

• The LNB cable must be earthed to the system earth for the satellite dish.

10. LOCATION

• Place the product indoors to avoid exposing it to lightning, rain or sun.

• Do not place it near a radiator or heat register.

• Make sure it has more than 10 cm clearance from any appliances susceptible to electromagnetic inuences, such as a TV or a VCR.

• Do not block the openings with any object, and do not place the product on a bed, sofa, rug, or other similar surface.

GB3

User’s Manual

Safety Warning

• If you place the product on a rack or a bookcase, ensure that there is adequate ventilation and that you have followed the manufacturer’s instructions for mounting.

• Do not place the product on an unstable cart, stand, tripod, bracket, or table where it can fall.

• A falling product can cause serious injury to a child or adult, and serious damage to the appliance.

11. LIGHTNING, STORM OR NOT IN USE

• Unplug the product from the wall outlet and disconnect the antenna during a thunderstorm or when left unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and power-surges.

12. EXTRANEOUS OBJECTS

• Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts.

13. REPLACEMENT OF PARTS

• When replacement of parts is required, be sure the service technician uses replacement parts specied by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitution may result in additional damage to the unit.

Warning

1. To avoid damage of the power cord or plug;

• Do not modify or process the power cord or plug arbitrarily.

• Do not bend or twist the power cord.

• Make sure to disconnect the power cord holding the plug.

• Keep heating appliances as far as possible from the power cord in order to prevent the cover vinyl from melting.

• The mains plug, as a disconnection device, shall remain readily accessible by the user.

2. To avoid electrical shock;

• Do not open the main body.

• Do not insert metal or inammable objects inside the product.

• Do not touch the power plug with wet hands.

Disconnect the power cord in case of lightning.

3. To avoid damage of product;

• Do not use the product when it is out of order. If you continue to use the product when defective, serious damage can be caused to it. Make sure to contact your local product distributor if the product is out of order.

• Do not insert metal or alien substance into the slots for the modules or Smartcards. It may cause damage to the product and reduce its life span.

GB4

User’s Manual

Contents

1. Before Using the Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB7

1.1 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GB7

1.2 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB8

1.3 Conditional Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB9

1.4 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB11

1.5 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB12

1.6 Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB14

2. Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB15

2.1 Connecting the TV and VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB15

2.2 Powering On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB20

3. Installation Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB21

3.1 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB21

3.2 Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB21

3.3 Antenna Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB22

3.4 Default Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB22

3.5 Antenna Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB23

3.6 Search Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB23

3.7 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB24

3.8 Result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB24

3.9 Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB25

4. Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB26

4.1 Switching Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB26

4.2 Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB26

4.3 Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB26

4.4 Sleep. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB27

4.5 Wide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB27

4.6 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB28

4.7 Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB28

4.8 Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB29

4.9 Programme Information (i-plate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB29

4.10 Multifeed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB31

5. Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB32

5.1 My TV List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB32

5.2 Favourite List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB34

5.3 Satellite List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB34

5.4 Scramble List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB35

6. TV Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB36

6.1 Using TV Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB36

6.2 List Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB37

6.3 Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB38

6.4 Find . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB39

GB5

User’s Manual

Contents

7. Preferences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB41

7.1 Parental Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB41

7.2 Language Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB43

7.3 Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB45

7.4 A/V Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB46

7.5 Other Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB48

8. Edit Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB50

8.1 Edit Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB50

8.2 Edit Favourite List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB53

8.3 Import/Export Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB55

8.4 Display History List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB55

9. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB56

9.1 Antenna Setting [Fixed] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB56

9.2 Antenna Setting [SCD Antenna]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB60

9.3 Antenna Setting [Motor] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB62

9.4 Antenna Setting [SMATV]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB67

9.5 IRDETO Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB69

9.6 Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB69

9.7 Default Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB71

10. System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB72

10.1 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB72

10.2 Signal Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB72

10.3 Common Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB72

10.4 Conditional Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB73

10.5 Mail Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB73

11. Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB74

11.1 OTA (Over the Air) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB74

12. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB75

12.1 Menu Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB75

12.2 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB76

12.3 Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB78

12.4 Specication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB80

12.5 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB82

12.6 Service and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB84

12.7 OPEN SOURCE SOFTWARE NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GB86

GB6

User’s Manual

1. Before Using the Product

This chapter provides detail instructions on the product and its accessories.

1.1 Package Contents

Please check all package contents before using your product.

Quick Start Guide

User Manual

www.humaxdigital.com

CD Manual

Batteries Quick Guide

Remote Control

Note:

• Faults may occur if the remote control is left without battery for a long time. Always keep the battery

inserted in the remote control.

• Package contents may vary according to area.

GB7

User’s Manual

1. Before Using the Product

1.2 Front Panel

21 3 4 865 7

1. STANDBY LED

Red light is emitted when the product is in standby mode.

2. STANDBY BUTTON

Switches between operation and standby modes.

3. TV/RADIO BUTTON

Switches between TV and radio modes.

4. CH-/CH+BUTTON

Moves the TV/radio channel up or down.

5. TV LED

Green light is emitted when the product is in TV mode.

6. RADIO LED

Amber light is emitted when the product is in radio mode.

7. SMARTCARD SLOT

A slot for a Smartcard

8. CI-MODULE SLOT

A slot for a CI-Module

Note:

The front panel of the product is subject to change without notice.

GB8

User’s Manual

1. Before Using the Product

1.3 Conditional Access

Although some TV and radio channels are free to air, most TV and radio/music channels are available on a subscription basis and can only be enjoyed via a Conditional Access component.

1. Inserting the Smartcard

The Smartcard looks similar to a credit card and is inserted into the slot behind the right-hand front ap of the product. A valid Smartcard entitles you to view and listen to all the channels you choose to subscribe to.

1. Open the right-hand ap on the front panel of the product to expose the card slot.

2. Hold the Smartcard horizontally with the electronic chip (small square-shaped, gold in colour) facing

upwards.

3. Insert the Smartcard into the top slot.

Smartcard

User’s Manual

GB9

1. Before Using the Product

2. Inserting a CI (with Smartcard)

A CI-Module looks like a PC map (PCMCIA) for laptops. There are dierent kinds of CI-Modules, suitable for dierent coding systems; Irdeto, Conax and more. Additionally to the CI-Module, a Smartcard is needed to decode the channels.

1. Open the right-hand ap on the front panel of the product to expose the card slot.

2. Follow the instructions of the module and insert the Smartcard into the CI-Module.

3. Keep the CI-Module (with the Smartcard) horizontal.

4. Insert the CI-Module into the slot.

GB10

User’s Manual

CI-Module

Smartcard

1. Before Using the Product

1.4 Rear Panel

1 42 6 7 8 9 10 11 123 5

1. LNB IN

Connects a satellite antenna cable.

2. LNB OUT

Connects another digital satellite receiver.

3. TV SCART

Connects to the TV using a TV SCART cable.

4. VCR SCART

Connects to the VCR or DVD using a VCR

SCART cable.

5. VIDEO

Connects to the TV or VCR using an RCA

cable.

6. AUDIO L/R

Connects to the TV or VCR using an RCA

cable.

Note:

The rear panel of the product is subject to change without notice.

7. COMPONENT(YPbPr)

Connects to the TV or VCR using a

component cable.

8. COMPONENT SELECT

Switch for changing video. (default: YPbPr)

9. S/PDIF

Connects to the audio system using an

S/PDIF cable. (digital audio)

10. HDMI

Connects to the TV using an HDMI cable.

11. USB Host

Channel list change/Software update

12. ETHERNET

Service connectivity. (for future use)

GB11

User’s Manual

1. Before Using the Product

1.5 Remote Control

1. MUTE

Mutes or unmutes the audio temporarily.

2. SLEEP

Sets the sleep time.

3. SOURCE

(currently not supported)

4. NUMERIC(0-9) BUTTONS

Enters a TV/radio channel number.

5. TEXT

Switches between the teletext and TV modes.

6. LIST

Displays the channel list.

7. ARROW BUTTONS

Changes the channel or moves the cursor up, down,

left or right.

8. EXIT

Exits all On-Screen Display (OSD) screens.

9. i (Information)

Displays the channel and programme information.

Note:

The remote control of the product is subject to change without notice.

GB12

User’s Manual

10. +/-

Adjusts the audio volume.

11. SCHEDULE

Displays the schedule in programme guide.

12. AUDIO

Displays the audio list.

1. Before Using the Product

13. STANDBY

Switches between operation and standby modes.

14. V-FORMAT

Changes the resolution of video.

15. WIDE

Sets the display format.

16. MENU

Displays the main menu.

17. COLOUR BUTTONS(R/G/Y/B)

Select the colour keys for interactive applications.

18. GUIDE

Displays the programme guide.

19. OK

Selects a menu or conrms the selected operation.

Displays the channel list while watching a programme.

20. BACK

Closes and returns to the previous menu and screen.

21. P(PAGE)

Changes the channel or page.

22. TV/RADIO

Switches between TV and radio modes.

23. SUBTITLE

Displays the subtitle language list.

23. OPT+

Displays the channels attributes while watching a

programme.

GB13

User’s Manual

1. Before Using the Product

1.6 Remote Control Batteries

1. Press down the top of the battery cover and slide the cover o.

2. Insert the new batteries. Make sure the plus (+) ends meet the plus markings on the battery case.

3. Slide the cover back into place.

i

GB14

User’s Manual

2. Setup

This chapter describes how to connect your product to the TV with the particular equipments for gaining optimum signal quality. The product provides various interfaces to connect to the TV, VCR or other devices. Select the most appropriate procedure depending on the equipment you have.

Note:

If you encounter any problems setting up your product, please contact your local product distributor.

2.1 Connecting the TV and VCR

You can select one of the following antenna connections depending on the equipment you have.

1. Using HDMI Cable

The HDMI connection is recommended for Digital TV. In case the TV has a HDMI input connector, a special all-digital interface that provides the highest picture quality, connect the product and the TV using a HDMI cable as follows.

LNB

LNB OUT

HDMI Cable

HDMI

GB15

User’s Manual

2. Setup

2. Using DVI Connector

The DVI connection using an HDMI to DVI converter is recommended for Digital TV. In case the TV has the DVI input connector only, connect the product to the TV with an HDMI cable using an HDMI to DVI converter as follows.

When equipped with an A/V receiver,

1. Connect one end of the HDMI cable to the HDMI input on the product and the other end to the HDMI to DVI converter.

2. Connect the DVI converter to the TV.

3. Connect the product and the Dolby Digital decoder using an S/PDIF cable.

LNB

LNB OUT

S/PDIF Cable

HDMICable

GB16

User’s Manual

2. Setup

When there is no A/V receiver available,

1. Connect the product and the TV using an RCA cable.

2. Connect one end of the HDMI cable to the HDMI input on the product and the other end to the HDMI

to DVI converter.

3. Connect the DVI converter to the TV.

Note:

You can also connect the product to the TV using the 3.5 Stereo Jack Cable to 2 RCA Y Cable.

Caution:

DO NOT CONNECT TO HEAD PHONE CONNECTOR ON TV!

LNB

LNB OUT

Y Cable (1stereo, 2RCA)

RCA Cable

HDMICable

GB17

User’s Manual

2. Setup

3. Using Component Cable

The component connection is recommended for Digital TV. Connect the product and the TV using a component cable as follows.

You can either:

• 1-1 Connect the product and the TV using an RCA cable (Audio L/R).

• 1-2 Connect the product and the Dolby Digital decoder using an S/PDIF cable.

Note:

The Component Select switch should be on YPbPr when using the component cable.

LNB

LNB OUT

GB18

User’s Manual

RCA Cable

AUDIO

Component Cable

COMPONENT IN

S/PDIF Cable

S/PDIF

2. Setup

4. Using SCART Cable

A SCART cable connection is recommended for analogue TV or VCR.

1. Connect the product and the TV using a SCART cable.

2. Connect the product and the VCR using a SCART cable.

Note:

• Connecting your TV directly to the audio/video output of the product will assure a more vivid picture

and enhance your viewing enjoyment.

• The

Component Select switch should be on RGB when using the SCART cable.

LNB

LNB OUT

SCART Cable SCART Cable

VCR SCART TV SCART

GB19

User’s Manual

2. Setup

2.2 Powering On

1. Connect the power cord of the product to a wall outlet.

2. Power on by pressing the of the product.

STANDBY button of the remote control or the STANDBY button at the front

GB20

User’s Manual

3. Installation Wizard

When powering on your product for the rst time after purchase, the installation wizard will operate automatically.

Tip: The default password is 0000. If you have forgotten your password, please contact your local

product distributor.

3.1 Language

Language allows you to select the main language.

Select the appropriate language from the list. Press the OK button to save.

3.2 Time Zone

Time Zone allows you to set the country and the current time of your region.

Select Country and press the OK or display the list of countries. Select the country and press the OK button.

If you have selected Other in Country, select GMT Oset and press the OK or time zone options. Select the appropriate time zone and press the OK button.

Select Daylight Saving Time and press the OK or

Select Next and press the OK button.

/ button to display the

/ button to

/ button to set the option if necessary.

GB21

User’s Manual

3. Installation Wizard

3.3 Antenna Type

Antenna Type allows you to set the antenna type.

1. Select antenna and press the OK button.

2. Select system antenna and press the OK button. Select the User Band and Band Frequency options.

3. Select

Fixed Antenna if you are using a xed

SCD Antenna if you are using a single cable

Next and press the OK button.

3.4 Default Channels

Default Channels allows you to select the default channel list of each country.

The satellites of the default channel list which belong to the country you have selected will appear.

Select Ye s and press the OK button to go to software update.

Select No and press the OK button to move to antenna setting.

GB22

User’s Manual

3. Installation Wizard

3.5 Antenna Setting

Antenna Setting allows you to congure the antenna setting parameters.

Satellite: Select the satellite and press the OK button.

LNB Frequency: Select the required LNB frequency and press the OK button.

22kHz Tone: Select Enable or Disable and press the OK button.

DiSEqC Input: Select the required DiSEqC input and press the OK button.

LNB Power: Select the required LNB power. When selecting High, a warning message will appear; select OK and press the OK button.

6. Select

7. Select

8. Select

Next and press the OK button to proceed.

Add and press the OK button to add another satellite. You can add up to four satellites. Search and press the OK button.

Note:

• If you cannot nd the required LNB frequency from the list, select

frequency using the NUMERIC(0-9) buttons and press the OK button.

• When using Universal LNB, select

Universal. The 22kHz tone value will be disabled.

3.6 Search Channels

Channel search will activate and the results will appear.

To stop the channel search, select Stop and press the OK button. Select Save and press the OK button to go to the next step.

User Dene and manually enter the

GB23

User’s Manual

3. Installation Wizard

3.7 Display

Display enables you to set the screen ratio, display format and resolution of the screen.

Select the value for Screen Ratio, Display Format and Resolution.

Select Next and press the OK button.

3.8 Result

After all setting is complete, you can view the result screen.

Select Finish and press the OK button to complete the installation wizard.

GB24

User’s Manual

3. Installation Wizard

3.9 Installation Checklist

Before using the product, please make sure that you have completed the following steps.

StepPage Done?

Is the antenna connected correctly? GB15

Is the product connected to your TV? GB15

Is the power cord plugged in the wall outlet? GB20

Is the product in operation mode (not Standby mode)? GB20

Have you performed channel search in the installation wizard? GB21

Note:

• If you exit the installation wizard without fully completing the channel searching procedure, you may

not have all of the channels available. In this case, you can use the installation menu to search for more channels.

• Be sure to operate channel search even when you have selected default channels.

GB25

User’s Manual

4. Basic Operation

This chapter describes the basic functions the product provides such as switching channel, volume control and other common features.

4.1 Switching Channel

You can switch the current channel by pressing the P(PAGE)/ button or entering the channel number directly using the NUMERIC(0-9) buttons. Press the TV/RADIO button to switch between TV channels and radio channels.

Note:

You can switch channels using the channel list or TV guide. To return to the previous channel, press the BACK button.

4.2 Volume Control

You can adjust the audio volume. Press the +/- button to adjust the audio volume. Press the MUTE button to stop the audio temporarily.

Note:

The mute function remains set while you switch channels.

4.3 Resolution

You can set the resolution of the screen. Press the V-FORMAT button while watching a programme. The current resolution will be displayed. Each time you press the V-FORMAT button, the resolution changes in the following sequence: 576i

576p720p1080iOriginal

Note:

When connected to a HDMI cable, you can change to resolutions the TV supports only.

GB26

User’s Manual

4. Basic Operation

4.4 Sleep

You can set the automatic turn o time.

Press the SLEEP button while watching a programme to set the sleep time. Each time you press the SLEEP button, the sleep time changes in the following sequence: 10, 20, 30, 60, 90, 120 minutes.

4.5 Wide

You can set the display format.

Press the WIDE button while watching a programme to change the display format. Each time you press the WIDE button, the display format changes.

Note:

For more information about display format, refer to 7.4.7 Display Format.

Screen ratio 4:3 Screen ratio 16:9

Format Icon and Text Format Icon and Text

Letterbox Letterbox Pillar box Pillar box

Pan & Scan Pan & Scan Zoom Zoom

Auto Auto Auto Auto

GB27

User’s Manual

4. Basic Operation

4.6 Audio

You can select the language you prefer in Audio if the current programme is available in multiple audio languages.

1. Press the

2. Select the audio language you prefer.

3. Select audio direction (left, right, stereo) using the

/ button.

4. Press the

Note:

AUDIO button.

EXIT button to close.

If the programme is broadcast in Dolby Digital, you cannot set the audio direction.

4.7 Subtitle

You can select the language for the subtitle if the programme provides subtitle information.

1. Press the

2. Select the required subtitle language and press the OK button. The subtitle will be displayed in the selected language at the bottom of the screen.

3. Select the subtitle from the screen.

SUBTITLE button.

O from the subtitle language list to hide

Note:

• When there is no subtitle available, appear.

• Subtitles will be always displayed when switching programmes unless you select Manual in the subtitle menu. Refer to 7.2.2 Subtitle Display for details.

O does not

GB28

User’s Manual

4. Basic Operation

4.8 Teletext

All teletext supporting channels have the teletext icon on the i-plate.

1. Press the

2. To display the teletext menu, press the

button in teletext mode.

3. Select the teletext function you want and press

the OK button. To view the teletext page, use the

CH+/CH or NUMERIC(0-9) buttons.

TEXT button.

4.9 Programme Information (i-plate)

The i-plate is always displayed for a certain period of time whenever you switch channels. You can view the programme information by pressing the i button while watching a programme. Press the EXIT button to hide the i-plate.

After switching to a channel, press the Press the Press the Press the OK button in navigation mode to reserve future programmes.

/ button to view the previous/next programme information. / button to view the programme information of other channels.

/ button to display navigation mode.

1. General Information

The general information is displayed on the screen as the following.

1 42

6 87

GB29

User’s Manual

4. Basic Operation

1. Channel number and name

2. Programme name

3. Icons

Displayed only when the channel is a locked channel.

Displayed only if the programme is reserved.

Represents parental level. Indicates the minimum level of age for viewing the programme.

1080i

Digital

4. Current time & date

5. Programme broadcasting time and progress bar: Displays programme playing time and progress bar.

6. Group name: Displays the group the channel belongs to.

7. Signal icon, status: Displays the signal strength and quality.

8. Previous/Next programme information: Displayed if previous/next programme information is provided. Press the

Note:

If there is no programme information available, programme information is not displayed.

Displayed only when the channel is a scrambled channel.

Displayed only when there is any teletext information.

Displayed only when subtitle information is available.

Displayed only when the channel provides HD programmes.

Displays the resolution of the current programme.

Displayed only when the programme is broadcast in Dolby Digital.

Displayed only when multifeed is supported.

/ button to display previous/next programme information.

2. Detailed Programme Information

You can see the detailed information about the current programme.

Press the i button when the i-plate is displayed to view detailed information. Press the i button once more to hide the i-plate.

Note:

If the detailed programme information is over one page, use the previous or next page.

/ button to move to the

GB30

User’s Manual

4. Basic Operation

4.10 Multifeed

You can choose from a choice of camera angles to watch the screen from dierent camera perspectives while watching a sports transmission. Dierent options are provided to view single matches or federal league games.

When tuning to a multifeed channel, the multifeed icon will appear on the i-plate.

1. Press the

channel.

2. Select

multifeed list will appear.

3. Select an option using the

the OK button.

Note:

OPT+ button after tuning to a multifeed

Multifeed and press the OK button. The

Please refer to 4.6 Audio for audio option.

/ button and press

GB31

User’s Manual

5. Channel List

This chapter will help you manipulate the channel list. You can display the channel list by pressing the OK button while watching a programme.

Four types of channel lists are provided for quick and easy channel search.

• TV:

My TV (RED)

Favourite (GREEN)

Satellite (YELLOW) The lists of channels classied by satellites.

Scramble (BLUE) The lists of channels classied by CAS types.

Note:

• Press the

• The sub-groups of favourite channel list exist only after conguration.

EXIT button to exit the channel list.

• Radio:

• HD TV:

• Recently Viewed:

The list of the favourite channels in ve groups.

• Most Viewed:

The list of all TV channels.

The list of all radio channels.

The list of all HD TV channels.

The list of the recently viewed channels.

The list of the most watched channels.

5.1 My TV List

My TV List is the list of all channels available including both TV and radio channels.

1. Press the to display the channel list.

2. Press the displayed.

3. Select the channel you wish to view and press the OK button. You can also enter the channel number using the NUMERIC(0-9) buttons.

4. Press the change the subgroup.

OK button while watching a programme

RED button while the channel list is

RED button again or use

/ buttons to

Note:

You can switch between TV and radio by simply pressing the TV/RADIO button.

GB32

User’s Manual

5. Channel List

1. Option

1. Select a channel and press the OPT+ button.

2. To add the channel to the favourite group, select

Favourite. Select the group using the and press the OK button.

3. To lock the channel, select

button.

4. To delete the channel, select

OK button. A popup will appear. Select Ye s and press the OK button.

5. To rename the channel, select

the OK button. Enter the name directly using the keyboard on the screen. Press the YELLOW button to complete.

Lock and press the OK

Delete and press the

Rename and press

/ button

2. Conguration

1. Press the MENU button.

2. To display the icon, enable

the OK button.

3. To display the channel number, enable

Channel Number and press the OK button.

4. To change the list type, select from

Column and Two Column and press the OK button.

Show Icon and press

Simple, One

Show

GB33

User’s Manual

5. Channel List

5.2 Favourite List

Favourite List is the list of the favourite channels you can select yourself from the entire channel list. There are ve favourite groups in total.

1. Press the

2. Press the favourite groups.

3. Press the favourite group using the

Note:

OK button while watching a programme.

GREEN button to display the list of

GREEN button again and select a

/ button.

To create a favourite list, refer to 5.1.1 Option.

5.3 Satellite List

Satellite List is the list of channels included in the satellite you select.

1. Press the

2. Press the list.

3. Press the satellite list using the

OK button while watching a programme. YELLOW button to display the satellite

YELLOW button again and select a

/ button.

GB34

User’s Manual

5. Channel List

5.4 Scramble List

Scramble List is the list of channels included in the CAS you select.

1. Press the

2. Press the

3. Press the

list using the

OK button while watching a programme. BLUE button to display the CAS list. BLUE button again and select a scramble

/ button.

GB35

User’s Manual

6. TV Guide

The TV Guide displays the programme information of each channel, in time and date order. You can customize your own programme guide to list the channels or programmes of interest to you and schedule your viewing using the programme information.

Note:

Press the GUIDE or EXIT button to exit the TV guide screen.

6.1 Using TV Guide

You can view the programme information of all channels in time and date order.

1. Press the

1. EPG Table

1. Move to the previous/next programme within the same channel using the

2. Move to another channel using the If the contents are more than one page, use the

P(PAGE)

Enter the number of the channel you wish to move using the NUMERIC(0-9) buttons.

3. Select the programme you want and press the button to play the programme in the PIG. Press the OK button again to view the programme.

4. You can reserve it if it is a future programme. Select a future programme and press the Select Ye s and press the OK button.

5. Select a reserved programme and press the

6. Press the a sub group using the

7. Press the

GUIDE button.

/ button.

/ button.

/ button to skip to the next page.

OK button to cancel the reservation.

OPT+ button to display the channel list. Select a channel group using the

/ buttons. Press the OK button.

WIDE button to change the length of the time scale in 30, 60, 90, 120 min order.

/ button. Select

OK button.

GB36

User’s Manual

6. TV Guide

2. Quick Browse Mode

1. Press the RED button to switch to Quick Browse

mode.

2. You can jump back/ahead two hours using the

/ button. You can move to the previous/next

day using the

3. Press the

selected programme.

4. Press the

list. Select a channel group using the Select a sub group using the the OK button to complete.

5. To return to the current time, press the

/ button.

OK button to watch or reserve the

OPT+ button to display the channel

/ button.

/ button. Press

BACK button.

6.2 List Guide

EPG List displays the programme information for approximately a week. The features are similar as in EPG table.

1 Press the

2. Press the

3. Press the

list. Select a channel group using the Select a sub group using the the OK button to complete.

4. Press the

selected programme.

Note:

• Press the

radio.

• Press the

• You can reserve the programme after viewing the programme information.

GUIDE button. GREEN button to switch to EPG list.

OPT+ button to display the channel

/ button.

/ button. Press

OK button to watch or reserve the

TV/RADIO button to switch to TV or

i button to view programme information.

GB37

User’s Manual

6. TV Guide

6.3 Schedule

Schedule displays the list of the programmes reserved. You can modify, delete or make new reservations.

1. Press the

2. Press the of reservations.

GUIDE button. YELLOW button to display the schedule

1. Editing Reservations

1. Select a reservation you want to edit and press the OK button. The reservation popup will appear.

2. Select the channel list. Select the channel.

3. Select calendar. Select the date.

4. Select using the NUMERIC(0-9) buttons.

5. Select using the

6. Select

Channel and press the OK button to display

Date and press the OK button to view the

Start Time or End Time and enter the time

Repeat and change the repeat frequency

/ button.

OK and press the OK button.

2. Deleting Reservations

1. Select a reservation you want to delete.

2. Press the

GB38

User’s Manual

OPT+ button to delete the reservation.

6. TV Guide

3. New Reservation

1. Select a blank space and press the OK button.

2. The reservation popup will appear. Enter the

channel number, date, start/end time, repeat frequency and then press the OK button.

Note:

• Reservations for deleted channels or past

programmes are automatically deleted.

• In case the channel number has changed,

reservation has to be done again.

6.4 Find

Find enables you to nd the programme you want by entering the genre, name, time and day of the programme.

1. Press the

2. Press the

3. Enter the keyword, genre, time & day of the programme and select

button.

GUIDE button. BLUE button to nd programme.

Search and then press the OK

1. Search by Keyword

1. Press the OK button while the cursor is on

Keyword.

2. A keyboard will appear. Enter the keyword.

3. Select

keyword.

4. Select

5. Press the

Note:

Language and choose the language of the

SMS to switch to SMS keyboard.

YELLOW button to complete.

Press the OPT+ button to display seven of the most recent keywords that have been entered.

GB39

User’s Manual

6. TV Guide

2. Search by Genre

1. Press the OK button while the cursor is on Genre.

2. The list of genres will appear. Select a genre and press the OK button.

3. Search by Time and Day

1. Press the OK button while the cursor is on Time & Day.

2. The time & day popup will appear. Select the time and day using the OK and

3. Select

OK and press the OK button.

/ button.

4. Search Result

1. Select Search and press the OK button to proceed.

2. The search result of the entered values will appear.

3. To reserve a programme, select a future programme and press the OK button.

4. To search again, press the

BLUE button.

GB40

User’s Manual

7. Preferences

In this chapter you can set parental control, language setting, time setting, A/V setting and other conguration items to keep limitations where you want them for the viewers.

Note:

Press the EXIT button to save the changes and return to the previous menu. Press the MENU button to exit the menu screen.

7.1 Parental Control

Parental Control allows you to set rating limits for each programme according to the age of the viewer or change your previous password. You can also lock the changes you have made using installation lock.

Tip: The default password is 0000.

1. Press the

2. Select

press the OK button.

3. Select

press the OK button.

4. You will be prompted to enter your password.

Enter the password using the NUMERIC(0-9) buttons.

MENU button.

Preferences using the

Parental Control using the

/ button and

1. Age Limit

Age Limit enables you to place certain restrictions on the viewers by setting age limits. The password is required to view the blocked programmes.

1. Select

2. Select the age limit you wish to set.

Note:

Age Limit and press the OK button.

View All

7, 12, 15, 18

Lock All All programmes are blocked.

You must enter your password to watch programmes blocked by the age restriction.

All programmes can be watched. (No age limitation)

Programmes are blocked for children under the age 7, 12, 15, 18.

GB41

User’s Manual

7. Preferences

2. Change Password

Change Password allows you to change the current password.

1. Select

2. Enter the password in NUMERIC(0-9) buttons.

3. Enter the password again in conrm.

Change Password and press the OK button.

New Password using the

Verify Password to

3. Installation Lock

Installation Lock allows you to block access to the installation menu settings you have previously made.

1. Select

2. Select

Installation Lock. Enable or Disable using the OK or

/ button.

GB42

User’s Manual

7. Preferences

7.2 Language Setting

Language Setting enables you to set the basic language and subtitle options such as menu language, subtitle display and subtitle font.

1. Press the

2. Select

press the OK button.

3. Select

and press the OK button.

MENU button.

Preferences using the

Language Setting using the

/ button and

/ button

1. Menu Language

Menu Language allows you to choose from the given language options and set the language for the menu.

1. Select

2. Select the language you want and press the

button.

Menu Language and press the OK button.

GB43

User’s Manual

7. Preferences

2. Subtitle Display

Subtitle Display allows you to display the subtitle automatically. This service is provided when subtitles are available.

1. Select

2. Select

Subtitle Display. Auto or Manual using the OK or

Auto Subtitles are displayed automatically in the predened subtitle language. Manual

Subtitles are displayed only when you press the SUBTITLE button and set subtitle.

/ button

3. Subtitle Font

Subtitle Font enables you to select the font of the subtitle.

1. Select

2. Select

Subtitle Font and press the OK button. Variable or Fixed using the OK or

Variable Uses the horizontally variable subtitle font of the on-screen display. Fixed

Uses the xed subtitle font as in teletext.

/ button

GB44

User’s Manual

7. Preferences

7.3 Time Setting

Time Setting allows you to set the current time and set the time you want to turn the product on or o.

1. Press the

2. Select

press the OK button.

3. Select

press the OK button.

MENU button.

Preferences using the

Time Setting using the

/ button and

1. Country

You can select the country that belongs to your time zone.

1. Select

2. Select your country and press the

Country and press the OK button.

OK button.

2. GMT Oset

If you have selected Other in Country, enter the GMT Oset of your region in this menu.

1. Select

2. Select the appropriate GMT oset value and press the

GMT Oset and press the OK button.

OK button.

GB45

User’s Manual

7. Preferences

3. Daylight Saving Time

You can choose to apply the daylight saving time.

1. Select

2. Select

Daylight Saving Time and press the OK button. O, On or Auto and press the OK button.

4. Power On

You can set the time the product turns on automatically.

1. Select

2. Enter the powering on time using the button.

Power On.

NUMERIC(0-9) buttons or select Disable using the OK or

5. Power On Channel

You can select the channel to watch when the product turns on at the preset wakeup time.

1. Select

2. Select the channel and press the

Power On Channel and press the OK button to display the channel list.

OK button.

6. Power O

You can select the time the product turns o automatically.

1. Select

2. Enter the powering o time using the button.

Power O.

NUMERIC(0-9) buttons or select Disable using the OK or

/

7.4 A/V Setting

You can congure the audio and video output settings.

1. Press the

2. Select press the OK button.

3. Select the OK button.

GB46

User’s Manual

MENU button.

Preferences using the

A/V Setting using the

/ button and

/ button and press

7. Preferences

1. TV SCART

You can select the TV SCART output option.

1. Select

2. Select among

Note:

TV-SCART and press the OK button.

CVBS, S-Video and RGB and press

the OK button.

You can select RGB only when the Component Select switch at the rear is on RGB.

2. VCR SCART

You can select the VCR SCART output option.

1. Select

2. Select

VCR-SCART. CVBS or S-Video using the OK or

3. Audio Output

You can select the audio output option.

/ button.

1. Select

2. Select

Audio Output. Stereo or Mono using the OK or

/ button.

4. Dolby Digital Auto Selection

You can set Dolby Digital automatically. If you select On, Dolby Digital audio will be output via S/PDIF.

1. Select

2. Select

Dolby Digital Auto Selection. O or On using the OK or

/ button.

5. Lip-Sync

You can adjust the sound dierence of audio and video.

1. Select

2. Adjust the sync using the

3. Press the

Note:

Lip-Sync and press the OK or

/ button.

BACK button to complete.

Lip-Sync is applied to all channels when once adjusted.

 button.

User’s Manual

GB47

7. Preferences

6. Screen Ratio

You can select the screen ratio option.

1. Select

2. Select

Screen Ratio. 4:3 or 16:9 using the OK or

/ button.

7. Display Format

You can select the display format according to the screen ratio.

1. Select

2. When choosing button.

3. When choosing

Display Format and press the OK button.

4:3 as screen ratio, select among Auto, Letter Box, Pan & Scan and press the OK

16:9 as screen ration, select among Auto, Pillar Box, Zoom and press the OK button.

Screen Ratio 4:3 16:9 Display Format Letter Box, Pan & Scan, Auto Pillar Box, Zoom, Auto

8. Letter and Pillar Box Colour

You can select the colour of the Letter Box and Pillar Box.

1. Select

2. Select

Letter and Pillar Box Colour and press the OK button. Black or Gray using the OK or

/ button.

7.5 Other Settings

You can congure other settings such as info display time, OSD transparency and Power saving in standby.

1. Press the

2. Select press the OK button.

3. Select press the OK button.

GB48

User’s Manual

MENU button.

Preferences using the

Other Settings using the

/ button and

7. Preferences

1. Info Display Time

You can set the automatic display time of the information box when the channel is switched.

1. Select

2. Select a value between

Note:

Info Display Time and press the OK button.

Disable, 1~ 20 seconds and press the OK button.

When set to Disable, the i-plate will not be displayed when you switch the channel.

2. OSD Transparency

You can set the transparency of the On-Screen Display.

1. Select

2. Select among

OSD Transparency and press the OK button.

Disable, 25, 50 and 75 and press the OK button.

Disable Fully opaque screen 25, 50, 75 The bigger the number, the more transparent the screen.

3. Power Saving in Standby

You can select whether the product switches to power saving mode in standby.

1. Select

2. Select from

Power Saving in Standby using the

On and O using the OK or

/ button.

/ button.

GB49

User’s Manual

8. Edit Channels

In this chapter you can edit all channels in the channel list or make changes to the favourite lists of the channels you have chosen.

Note:

• Press the exit the menu screen.

• Press the

8.1 Edit Channel List

Edit Channel List enables you to delete, move, select, rename or lock/unlock the channels in the channel list conveniently.

EXIT button to save the changes and return to the previous menu. Press the MENU button to

TV/RADIO button to move to TV or radio channel list directly.

1. Press the

2. Select press the OK button.

3. Select press the OK button.

MENU button.

Edit Channels using the

Edit Channel List using the

/ button and

1. Deleting Channels

1. Select the channels you want to delete and press the OK button. You can select more than one channel.

2. Press the channels.

RED button to delete the chosen

GB50

User’s Manual

8. Edit Channels

2. Moving Channels

1. Select the channels you want to move and press

the OK button. You can select more than one channel.

2. Press the

channels. The selected channel disappears from the channel list temporarily.

3. Move the cursor to the destination in the channel

list and press the OK button.

Note:

•

Move is available only for TV or radio channel lists.

• The channel number is changed by using

3. Selecting a Channel Group

GREEN button to move the chosen

Move function.

1. Press the YELLOW button to display the list of

groups.

2. Select the group you want and press the

button.

GB51

User’s Manual

8. Edit Channels

4. Renaming Channels

1. Select the channel you want to rename and press the OK button.

2. Press the

3. Select

4. Enter a channel name directly using the keyboard displayed on the screen.

5. Press the

5. Locking/Unlocking Channels

BLUE button.

Rename and press the OK button.

YELLOW button to complete.

Tip: The default password is 0000.

1. Select the channel you want to lock and press the

2. Press the

3. Select

Note:

• When all selected channels are locked, locked channel is switched into an unlocked channel.

• To watch locked channels, you must enter the password using the

BLUE button.

Lock and press the OK button.

Lock is switched into Unlock. When you press Unlock, the

OK button.

6. Select All/Release All

1. Press the BLUE button.

2. Select

3. To release one or more channels from select all, press the channel.

Select All and press the OK button.

OK button while the cursor is on the selected

NUMERIC(0-9) buttons.

GB52

User’s Manual

8. Edit Channels

8.2 Edit Favourite List

You can add or remove channels from the favourite groups, move favourite channels, rename favourite groups and move the favourite groups.

1. Press the

2. Select

press the OK button.

3. Select

and press the OK button.

MENU button.

Edit Channels using the

Edit Favourite List using the

/ button and

/ button

1. Adding/Removing Channels

1. Select the channels you want to add to the

favourite channel list and press the OK button.

2. Press the

favourite list you have chosen.

3. To remove channels from the favourite list, select

the channels from the list and press the RED button.

RED button to add the channels to the

Note:

When the cursor is on the left column, the red button is marked Add; when the cursor moves to the right column, it becomes Remove.

2. Selecting Favourite Groups

1. Press the GREEN button to display the list of groups.

2. Select the favourite group you want and press the

OK button.

GB53

User’s Manual

8. Edit Channels

3. Select All/Release All

1. Press the YELLOW button to select all channels in the favourite list.

2. To release all channels, press the

4. Renaming Favourite Groups

1. Select the favourite group you want to rename and press the OK button.

2. Press the

3. Select

4. A keyboard will appear. Enter the name of the favourite group using the keyboard.

5. Press the

BLUE button.

Rename Group and press the OK button.

YELLOW button to complete.

YELLOW button again.

Note:

The YELLOW and BLUE buttons become activated only when the cursor is placed on the right column.

5. Moving Favourite Channels

1. Select the favourite channels to move within the favourite channel list and press the OK button.

2. Press the

3. Select

4. Move the cursor to the destination using the

5. The selected channel is moved to the new location.

BLUE button.

Move and press the OK button.

/ button, and press the OK button.

GB54

User’s Manual

8. Edit Channels

8.3 Import/Export Channels

The channel data can be imported from the USB to the receiver or exported from the receiver to a USB device(such as USB memory stick). The le format of the channel data is .udf format.

Note:

1. Press the

2. Select

3. Select

You can edit the channel data using Uniformula. Refer to the Humax website for information. (http://www.humaxdigital.com)

MENU button.

Edit Channels using the

Import/Export Channels using the

/ button and press the OK button.

1. Import Channels from USB

You can import the channel data from a USB device. The folders and channel data from the USB device will be displayed in a list.

1. Select

OK button.

2. Import Channels list will appear. Select a channel

data le and press the OK button.

3. Select

The channel data will be imported. The system will reboot if necessary.

Import Channels from USB and press the

Ye s and press the OK button.

2. Export Channels to USB

You can export the channel data to a USB device.

1. Select

2. A popup will appear. Select

The channel data will be exported.

Export Channels to USB and press the OK button.

Ye s and press the OK button.

8.4 Display History List

You can choose to display the history list in the channel list.

1. Press the MENU button.

2. Select Edit Channels using the

2. Select Display History List using the

4. Select Disable or Enable using the OK or

/ button and press the OK button.

/ button.

GB55

User’s Manual

9. Installation

In this chapter you can congure the installation setting and perform channel search. Menus such as antenna setting, search channels, IRDETO software update and default setting is included in this section.

Note:

Press the EXIT button to save the changes and return to the previous menu. Press the MENU button to exit the menu screen.

9.1 Antenna Setting [Fixed]

You can set the antenna and LNB information for channel search. If the antenna is not properly set, channel search cannot be activated which means you cannot watch any of the programmes on air.

MENUInstallationAntenna Setting [Fixed]

1. Press the

2. Select press the OK button.

3. You will be prompted to enter the password. Enter the password to proceed.

4. Select press the OK button.

MENU button.

Installation using the

Antenna Setting using the

/ button and

1. Antenna Type

1. Select Antenna Type and press the OK button.

2. Select button.

GB56

User’s Manual

Fixed Antenna and then press the OK

9. Installation

2. Satellite Setting

1. Select Satellite Setting and press the OK button.

2. Enter the value for

22kHz Tone, DiSEqC Input, LNB Power and Transponder.

3. Select

Save and press the OK button to complete.

Satellite

Select the satellite the antenna is pointing to and press the OK button. If the required satellite is not available, select User Dene and enter the name of the satellite directly.

LNB Frequency

Satellite, LNB Frequency,

Select the LNB frequency value and press the OK button. If the required value is not available, select User Dene and enter the LNB frequency directly.

Note:

If you select Universal, the 22kHz Tone will be set to Auto.

22kHz Tone

Select Disable or Enable using the OK or / button.

Enable Dual LNB is used or two antennas are connected to the 22kHz tone switch box. Disable 22kHz tone is not in use.

DiSEqC Input

Select the DiSEqC input option and press the OK button.

LNB Power

Select Standard or High and press the OK button.

Transponder

Set the transponder to check the signal status. Select the value for the transponder. If the required value is not available, select User Dene and enter the transponder value directly.

Select Search and press the OK button to go to search channels.

GB57

User’s Manual

9. Installation

Select Search and press the OK button to go to search channels.

3. Search Channels

Satellite

Select All or the name of the satellite in antenna setting.

Transponder

Select All or the value in the transponder list and press the OK button. If the required value is not available, select User Dene and enter the transponder value directly.

Network Search

Select Disable or Enable using the OK or / button.

Scrambled Type

Select among All, FTA and CAS and press the OK button.

Channel Type

Select among All, TV and Radio and press the OK button.

Select Search and press the OK button. The channel search will start. To stop the search, press the OK button during channel search.

The results will appear. Select Save and press the OK button.

Note: If there are no channels available, a message indicating the result will pop up.

GB58

User’s Manual

9. Installation

4. Set Transponder

Transponder setting is normally xed. Change the setting only when necessary.

1. Select

OK button.

2. Enter the value for

Symbol Rate, Transmission, Modulation and FEC.

3. Select

User Dene in Transponder and press the

Frequency, Polarisation,

Done and press the OK button to complete.

Frequency

Enter the frequency using the NUMERIC(0-9) buttons.

Polarisation

Select among Auto, Horizontal and Vertical and press the OK button.

Symbol Rate

Select the symbol rate and press the OK button. If the required symbol rate is not available, select User Dene and enter the symbol rate directly.

Transmission

Select DVB or DVB-S2 and press the OK button.

Modulation

Select QPSK or 8PSK and press the OK button.

FEC

Select the FEC value and press the OK button.

Note:

Transmission DVB DVB-S2

Modulation Disabled QPSK 8PSK Symbol Rate 2-45Ms/s 10-30Ms/s 10-31Ms/s

FEC

When Transmission is set to DVB, Modulation is disabled. The values for Symbol Rate and FEC dier depending on the value of Modulation. Refer to the table below.

Parameter Value

Auto, 1/2, 2/3, 3/4, 5/6,

7/8

Auto, 1/2, 2/3, 3/4, 3/5, 4/5,

5/6, 8/9, 9/10

Auto, 3/5, 2/3, 3/4, 5/6, 8/9,

9/10

GB59

User’s Manual

9. Installation

9.2 Antenna Setting [SCD Antenna]

MENUInstallationAntenna Setting [SCD Antenna]

SCD Antenna

Single Cable Distribution enables the delivery of broadcast programming over a single cable to multiple users eliminating the numerous cables required to support other electronics devices. If you are using more than one satellite receiver, set one receiver at a time and turn o the others while setting. Refer to the satellite antenna manual for details.

1. Press the

2. Select press the OK button.

3. Select

4. Select

5. Enter the value for

MENU button.

Installation using the

Antenna Setting using the SCD Antenna in the Antenna Type menu.

User Band, Band Frequency and Satellite Setting.

/ button and

/ button and press the OK button.

1. User Band

Select the user band form 1-8 and press the OK button.

2. Band Frequency

The default value of the band frequency is displayed according to the user band. Select the value and press the OK button. You can also enter the band frequency directly.

GB60

User’s Manual

9. Installation

3. Satellite Setting

1. Select Satellite Setting and press the OK button.

2. Enter the value for

Power, Satellite Position and Transponder.

3. Select

Save and press the OK button to complete.

Satellite

Select the satellite the antenna is pointing to and press the OK button. If the required satellite is not available, select User Dene and enter the name of the satellite directly.

LNB Frequency

Select the LNB frequency value and press the OK button. If the required value is not available, select User Dene and enter the LNB frequency directly.

Satellite, LNB Frequency, LNB

Note:

If you select Universal, the 22kHz Tone will be set to Auto.

LNB Power

Select Standard or High and press the OK button.

Satellite Position

Select Position1 or Position2 and then press the OK button.

Transponder

Select the value for the transponer. If the required value is not available, select User Dene and enter the transponder value directly.

4. Search Channels

Select Search and press the OK button. The channel search will start. To stop the search, press the OK button during channel search. The results will appear. Select Save and press the OK button.

GB61

User’s Manual

9. Installation

9.3 Antenna Setting [Motor]

MENUInstallationAntenna Setting [Motor]

1. Press the MENU button.

2. Select press the OK button.

3. Select press the OK button.

4. Select

5. Select

Installation using the

Antenna Setting using the

Motor Antenna in the Antenna Type menu. Satellite Setting and press the OK button.

/ button and

1. Motor Setting

You can set the motor antenna for ecient channel search.

1. Select

2. Enter the value for

LNB Frequency

Select the LNB frequency value and press the OK button. If the required value is not available, select User Dene and enter the LNB frequency directly.

GB62

User’s Manual

Motor Setting and press the OK button.

LNB Frequency, LNB Power,

Motor Type, My Longitude and My Latitude.

9. Installation

LNB Power

Select Standard or High using the OK or / button.

Note:

When LNB Power is set to High, a popup appears; ”High LNB Power. Only for LNB cable over 30m. Set LNB Power High.”

Motor Type

Select DiSEqC 1.2 or USALS using the OK or / button.

DiSEqC 1.2 General motor antenna using DiSEqC 1.2 USALS Motor antenna using USALS.

Note: When Motor Type is set as DiSEqC 1.2, both My Longitude and My Latitude are disabled.

My Longitude

Enter the longitude using the NUMERIC(0-9) buttons. Select East or West using the / button and press the OK button.

My Latitude

Enter the latitude using the NUMERIC(0-9) buttons. Select North or South using the / and press the OK button.

2. Edit Satellite Data

You can set the position of the satellite that the motor antenna is pointing to and decide whether to use the satellite.

1. Select

button.

2. Enter the value for

Satellite Longitude.

3. Select

return to the previous screen.

Satellite

Select a satellite to edit and press the OK button.

Edit Satellite Data and press the OK

Satellite, Activate Satellite and

Save and press the OK button to save and

GB63

User’s Manual

9. Installation

Activate Satellite

Select Disable or Enable using the OK or / button.

Enable Channel search is available. Disable Current channel does not exist. Channel search unavailable.

Note: Activate Satellite is activated only when User dene is selected in Satellite menu.

Satellite Longitude

Enter the longitude using the NUMERIC(0-9) buttons. Select East or West and press the OK button.

3. Position Setting

1. Select Position Setting using the / button.

2. Enter the value for

Driving, and Driving Size.

Satellite, Transponder, Motor

Satellite

Select the satellite the antenna is pointing to and press the OK button. If the required satellite is not available, select User Dene and enter the name of the satellite directly.

Transponder

Select the value for the transponder. If the required value is not available, select User Dene and enter the transponder value directly.

Motor Driving

1. Select among Continuous, Step or Time and press the OK button.

2. When motor driving a set to using the OK or

/ button.

Step or Time, the Driving Size option is enabled. Select the driving size

Go to Stored Position

1. Press the OK button to move the antenna to the position of the selected satellite.

2. Wait until the antenna moves to the position of the satellite.

3. Conrm signal strength and quality level and ne-tune the antenna direction. Move the antenna East/ West by pressing the

/ button. Adjust the signal level to maximum.

GB64

User’s Manual

9. Installation

Store Current Position

1. Press the OK button to save the adjusted position of the satellite.

2. The position of the antenna headed for the certain satellite will be saved.

Note:

You can set the antenna position by repeating the procedure above.

Recalculate

1. Press the OK button to recalculate the position of the satellites based on one satellite.

2. To readjust all positions, select

Note:

When Motor Type is set as USALS, Motor Driving, Store Current Position and Recalculate are disabled.

Ye s and press the OK button.

4. Limit Setting

You can set the default setting and operation limit for the motor antenna.

1. Select

2. Enter the value for

Motor Limit

You can set the maximum motor limit for both East and West to prevent damage to the antenna. Select O or On using the OK or

Limit Setting and press the OK button.

Motor Limit and Limit Position.

/ button.

O Motor limit setting is released.

Note:

Motor limit is set. Motor does not exceed the limit.

Select O when setting a new motor limit.

Limit Position

Select East or West using the OK or / button.

East Sets East limit. West Sets West limit.

GB65

User’s Manual

9. Installation

Set Limit

1. Press the OK button.

2. Move the antenna to the East or West using the

/ button.

Note:

When the limit is set, Motor Limit is automatically enabled.

Reset Position

1. Press the OK button to restore the position saved at the motor antenna to factory default.

2. A popup will appear. Select factory default.

Note:

Reset may not activate depending on the condition of the antenna. Repeat the procedure above if necessary.

OK and press the OK button to reset all values saved at motor antenna to

5. Search Channels

Satellite

Select All or the name of the satellite in antenna setting.

Transponder

Select All or the value in the transponder list and press the OK button. If the required value is not available, select User Dene and enter the transponder value directly.

Network Search

Select Disable or Enable using the OK or / button.

Scrambled Type

Select among All, FTA and CAS and press the OK button.

Channel Type

Select among All, TV and Radio and press the OK button.

Select Search and press the OK button. The channel search will start. To stop the search, press the OK button during channel search.

The results will appear. Select Save and press the OK button.

Note: If there are no channels available, a message indicating the result will pop up.

GB66

User’s Manual

9. Installation

9.4 Antenna Setting [SMAT V ]

MENUInstallationAntenna Setting [SMAT V ]

1. Press the MENU button.

2. Select

press the OK button.

3. Select

press the OK button.

4. Select

5. Select

1. Automatic Search

Installation using the

Antenna Setting using the

SMATV in the Antenna Type menu. Search and press the OK button.

/ button and

Scrambled Type

1. Select Scrambled Type.

2. Select

Auto using the OK or

/ button.

Start Frequency

1. Select Start Frequency.

2. Enter the start frequency using the

buttons.

Note:

Enter the frequency from 950 to 2150MHz.

NUMERIC(0-9)

End Frequency

1. Select End Frequency.

2. Enter the end frequency using the

Note:

Enter the frequency from 950 to 2150MHz.

NUMERIC(0-9) buttons.

Symbol Rate(1)-(4)

1. Select Symbol Rate(1)~(4) and press the OK button.

2. Select the symbol rate and press the

Dene and enter the symbol rate directly.

OK button. If the required value is not available, select User

Select Search and press the OK button. The channel search will start. To stop the search, press the OK button during channel search.

User’s Manual

GB67

9. Installation

2. Manual Search

Scrambled Type

1. Select Scrambled Type.

2. Select

Frequency

1. Select Frequency and enter the frequency using the NUMERIC(0-9) buttons.

Manual using the OK or

/ button.

Note:

Enter the frequency from 950 to 2150MHz.

Symbol Rate

1. Select Symbol Rate and press the OK button.

2. Select the symbol rate and press the Dene and enter the symbol rate directly.

OK button. If the required value is not available, select User

Transmission

Select DVB or DVB-S2 and press the OK button.

Modulation

Select QPSK or 8PSK and press the OK button.

FEC

1. Select FEC and press the OK button.

2. Select

Select Search and press the OK button. The channel search will start. To stop the search, press the OK button during channel search.

Auto or the FEC and press the OK button.

The results will appear. Select Save and press the OK button.

Note:

If there are no channels available, a message indicating the result will pop up.

GB68

User’s Manual

9. Installation

9.5 IRDETO Software Update

You can update the IRDETO software.

MENUInstallationIRDETO Software Update

1. Press the MENU button.

2. Select Installation using the the OK button.

3. Select IRDETO Software Update using the button and press the OK button.

4. You will be prompted to enter your PIN-Code. Enter the PIN-Code using the NUMERIC(0-9) buttons.

/ button and press

/

Note:

IRDETO Software Update is activated only when OTA is available.

9.6 Software Update

Software Update allows you to update the system software.

MENUInstallationSoftware Update

1. Press the

2. Select

press the OK button.

3. Select

press the OK button.

MENU button.

Installation using the

Software Update using the

/ button and

1. Automatic Update

1. Select Automatic Update and press the OK button.

2. When new software is detected, you can choose to download the software immediately or save for

later.

3. When there is no new software to update, a popup will appear.

GB69

User’s Manual

9. Installation

2. Manual Update

1. Select Manual Update and press the OK button.

2. Enter the values for Polarisation, Symbol Rate and FEC.

3. Select

4. When new software is detected, you can choose to download the software immediately or save for later.

Search and press the OK button.

Satellite, Frequency,

Note:

When there is no new software to update, a popup will appear.

Satellite

Select the name of the satellite in antenna setting.

Frequency

Enter the frequency using the NUMERIC(0-9) buttons.

Polarisation

Select one option among Auto, Horizontal and Vertical and press the OK button.

Symbol Rate

Select one option among 27500, 26000 and 22000 and press the OK button. If the required value does not exist, select User Dene and enter the symbol rate directly.

Transmission

Select DVB or DVB-S2 and press the OK button.

Modulation

Select QPSK or 8PSK and press the OK button.

FEC

Select one option among Auto, 1/2, 2/3, 3/4, 5/6 and 7/8 and press the OK button.

GB70

User’s Manual

9. Installation

9.7 Default Setting

Default Setting enables you to restore the product to the factory default.

MENUInstallationDefault Setting

Warning:

Note:

1. Press the

2. Select

press the OK button.

3. Select

4. Select

menu, select No and press the OK.

5. You will be prompted to enter your password again before starting to load default setting. Enter the

password to proceed.

6. When default setting is completed, installation wizard pops up automatically and assists channel

search.

Tip: The default password is 0000.

Please note that once you perform Default Setting, all data such as antenna setting information, channel list, and all user congured data will be deleted. However, the les in the hard disk drive will not be deleted.

The les in the hard disk drive will not be deleted.

MENU button.

Installation using the

Default Setting using the Ye s and press the OK button to restore all setting to factory default. To return to the previous

/ button, and

/button and press the OK button.

Note:

For detailed information about the installation wizard, refer to Chapter 3. Installation Wizard.

GB71

User’s Manual

10. System

10.1 Status

You can view the model name, software version, update date, system ID, Micom version and MAC address of the product. The CI-Module slot is also displayed.

1. Press the

2. Select OK button.

3. Select OK button.

4. The system status information will be displayed.

MENU button.

System using the

Status using the

/ button and press the

10.2 Signal Detection

You can view the satellite, transponder information, signal strength and quality of the tuner.

1. Press the

2. Select OK button.

3. Select press the OK button.

4. The information of the tuner will be displayed.

MENU button.

System using the

Signal Detection using the

/ button and press the

/ button and

10.3 Common Interface

You can view the CI-Module information.

1. Press the

2. Select OK button.

3. Select and press the OK button.

4. The common interface information will be displayed.

GB72

User’s Manual

MENU button.

System using the

Common Interface using the

/ button and press the

/ button

10. System

10.4 Conditional Access

1. Press the MENU button.

2. Select

OK button.

3. Select

and press the OK button.

4. The Smartcard information will be displayed.

1. Maturity Rating

You can set Maturity Rating options and require a Maturity Rating PIN when attempting to watch programmes blocked by the age limit. The correct Maturity Rating PIN must be entered when watching programmes that are rated above the restricted age.

System using the

Conditional Access using the

/ button and press the

/ button

1. Select

press the OK button.

2. Select a user name and press the

3. A popup will appear. You can enable or disable the

Maturity Rating option for the selected user and enter the age limit.

4. Select

Maturity Rating using the

OK and press the OK button to complete.

/ button and

OK button.

10.5 Mail Messages

1. Press the MENU button.

2. Select

3. Select

4. The mail messages will be displayed.

System using the Mail Messages using the

/ button and press the OK button.

GB73

User’s Manual

11. Software Update

In order to maintain proper performance of the product, it is essential to have the most up-to-date software. Visit the Humax website to check the latest news and newly released software versions. (http:// www.humaxdigital.com) It is recommended that you periodically check for the availability of software update.

11.1 OTA (Over the Air)

OTA, an abbreviation of Over-the-Air, is a standard for the transmission of software through a broadcast system. OTA is simply an alternative method for downloading software versions. However, the manufacturers reserve the right for deciding the release of the software for their products by beaming the latest software versions over the air via satellite. Note that OTA is only limited to certain geographical regions mainly due to dierent antennas having dierent footprints (area where the signal can be received). The software update via satellite will only occur under the following circumstances.

1. The equipment should have the appropriate loader software.

Caution:

2. The manufacturer decides to release the software via a designated satellite.

3. The equipment must be tuned properly to the same antenna equivalent to that of the manufacturer.

4. Update software when the signal strength and quality is high. If the weather is not favorable, and the signal strength and quality are not recommendable, perform the software update later.

Caution:

• Please be careful to keep the power on and the power cord plugged in during software update. If the power is o during software update, fatal damage may be caused to the product.

• Please be careful not to pull out the signal line (LNB cable) during software update. Update may be interrupted and the product may not operate.

Note:

• It may take 5~10 minutes to update software.

• Other functions will not activate while software update takes place.

• You cannot schedule programmes during software update.

Please note that if the normal loader software is not equipped, the product may not be updated or operate properly after software update.

GB74

User’s Manual

12. Appendix

12.1 Menu Map

Preferences

1. Parental Control

2. Language Setting

3. Time Setting

4. A/V Setting

5. Other Settings

1. Edit Channel List

2. Edit Favourite List

3. Import/Export Channels

4. Display History List

Edit Channels

Installation

System

1. Antenna Setting

2. Search Channels

3. IRDETO Software upate

4. Software Update

5. Default Setting

1. Status

2. Signal Detection

3. Common Interface

4. Conditiional Access

5. Mail Messages

GB75

User’s Manual

12. Appendix

12.2 Trouble Shooting

Before contacting your local service centre, please read the tips below carefully. If the problem persists after completing the following procedure, please contact your local product distributor or service centre for further instructions.

1. No message displayed on the front panel. (The product will not switch on.)

• Check the main power cable and make sure it is plugged into a suitable power outlet.

• Check that the mains supply is switched on.

• Check that the power switch is on at the rear of the product. (where applicable)

• Connect the power cable to a dierent power outlet.

2. No picture on TV set

• Make sure that the product is powered on and in operation mode. (Press the STANDBY button)

• Make sure that the AV cable is rmly connected to the TV.

• Make sure that the antenna cable is properly connected to the product.

• Make sure that the antenna setting in the menu is correct.

• Check the brightness level of the TV.

• Check if the channel is currently on air. Contact the broadcaster to ensure that the channel is running.

• Press the SOURCE button if the product is in external input mode.

3. Poor picture/sound quality

• Install the antenna in an obstacle-free place.

• Make sure there is no mobile phone or microwave oven near the product.

• Keep the power and the antenna cable for the satellite apart from each other.

• Check the signal levels and adjust your antenna if the level is too low. The signal level may be aected by

weather conditions.

Note:

If the antenna is covered with snow or the RF is weakened by heavy rain, the condition of the sound and picture may temporarily be poor. However, the poor sound and picture quality due to weather conditions cannot be accepted as a malfunction of product.

• Check that your dish alignment is correct.

• Change the satellite dish for a larger one as this will increase the signal levels received.

• Replace the LNB with a lower noise factor in cases where the noise factor is too high.

• Replace the LNB with a new one in case it is damaged or out of order.

4. No or poor sound

• Check that your AV cable is connected correctly.

• Check the volume levels of your TV set and the product.

• Check if the product or TV is on mute.

• Check audio type or soundtrack option in the AV menu.

5. Remote control does not operate.

• To control the product, the top end of the remote control should point directly towards the receiving part of the

product.

GB76

User’s Manual

12. Appendix

• Remove and reinsert the batteries in the remote control.

• Replace the batteries in the remote control for a new set.

6. Cannot make reservations.

• Check that no previous reservations are conicting with the new reservation.

7. No password information is given.

• The default password is always 0000.

8. Channel search does not work.

• Make sure that the antenna setting in the menu is correct.

9. Cannot update new software.

• You can get an update. If the product does not show a message requesting update, that means no software is available.

10. Cannot watch scrambled channels.

• Check that you have the appropriate Smartcard or CI-Module. Reinsert the Smartcard or CI-Module and make sure it initializes correctly.

• Check in the menu that the product is detecting the Smartcard or CI-Module.

• Check in the menu that you have a valid and working subscription to the channels you wish to view.

• Ensure that the Smartcard or CI-Module is not damaged.

11. Cannot watch pay channels.

• Check in the menu that you have a valid and working subscription to the channels you wish to view.

• Contact your network operator for more information.

GB77

User’s Manual

12. Appendix

12.3 Error Message

Error message Possible causes What to do

No or bad signal

The channel is

scrambled or not available.

The satellite dish is not pointing at the satellite.

Signal is too weak.

Satellite dish is too small. Change to a larger dish.

Problem with LNB. Change the LNB.

Wrong antenna setting. Set the antenna correctly.

The channel has a signal, but no audio or video is provided.

The channel has not been deleted by broadcasting company.

The channel is for data broadcasting.

Smartcard is not plugged in. Insert Smartcard.

Wrong Smartcard is in use.

Adjust dish alignment.

Increase the LNB voltage or connect a signal amplier.

Conrm if the channel is currently on air.

Remove the channel from the channel list and check for new transponder details.

The channel cannot be viewed with the appropriate model that supports data channels.

Insert the appropriate Smartcard for the channel(s) you wish to view.

Audio not available.

CI-

Module not

installed

GB78

User’s Manual

Smartcard is not plugged in correctly.

Smartcard is damaged.

The channel has a video signal, but no audio is provided.

CI-Module is not installed. Insert CI-Module

CI-Module is not inserted correctly. Reinsert CI-Module.

CI-Module is not recognized.

Reinsert Smartcard; ensure that it is inserted correctly.

Contact your Smartcard retailer or channel broadcaster for a Smartcard replacement.

Press the audio button on your remote control to conrm that the channel has audio options.

Insert a dierentCI-Module to check if your existing module is working.

12. Appendix

Error message Possible causes What to do

Wrong CI-Module. Insert the correct CI-Module.

Invalid CI-Module

Short LNB

CI-Module is not inserted correctly. Remove and reinsert the CI-Module.

CI-Module is damaged. Replace CI-Module.

LNB cable is short. Replace LNB Cable.

LNB is internally short. Replace LNB.

Alien substance is inserted in LNB IN Port and port may be damaged.

Remove the alien substance and contact local service center in case damaged has occurred.

GB79

User’s Manual

12. Appendix

12.4 Specication

Tuner & Channel

No of Tuners 1

Input Connector F-Type, IEC 169-24, Female (with loop through)

Frequency Range 950MHz to 2150MHz

Signal Level -25 to -75dBm

Vertical : +13.5V (+14.5V at high voltage)

LNB Power & Polarisation

Horizontal : +18V (+18.5V at high voltage) Current : Max. 500mA (Overload protection)

22KHz Tone

DiSEqC Control Version1.0, 1.2, USALS, SCD (Single Cable Distribution)

Demodulation QPSK, 8PSK

Input Symbol Rate

FEC Mode

MPEG Transport Stream A/V Decoding

Transport Stream

Prole Level MPEG-2MP@ML, MPEG-2MP@HL, MPEG-4 HP@L4 .1

Input Rate 15MB/s Max

Video Format 4:3, 16:9

Video Resolution 1080i, 720p, 576p, 576i

Frequency : 22 ± 4KHz Amplitude : 0.7 ± 0.2V

DVB : 2-45Ms/s DVB-S2 : 10-30Ms/s (QPSK), 10-31Ms/s (8PSK)

DVB: Auto,1/2,2/3,3/4,5/6,7/8 DVB-S2: Auto,1/2,3/5,2/3,4/5,5/6,8/9,9/10 (QPSK) Auto,3/5,2/3,3/4,5/6,8/9,9/10 (8PSK)

MPEG-2 ISO/IEC 13818 Transport Stream Specication

Audio Decoding MPEG/MusiCam Layer I & II, Dolby Digital Plus downmix

Audio Mode Single channel/Dual channel/Joint stereo/Stereo

GB80

User’s Manual

12. Appendix

Memory

Flash Memory 8MB

RAM 128MB

EEPROM 8KB

Audio/Video/Data In/Out

TV-SCART(FBAS,S-Video,RGB)

Video

Audio TV-SCART, VCR-SCART, Audio L/R, S/PDIF(Digital Audio Output)

Data Port

USB USB 2.0 Host (5 V 100mA Max.)

VCR-SCART(FBAS, S-Video) RCA-Type(FBAS), YPbPr(RCA), HDMI/HDCP

Power Supply

Input Voltage 90-250V a.c., 50/60Hz

Typ e SMPS

Power Consumption Max. 30W

Protection

Physical Specication

Size 310mm × 60mm × 237mm

Weight (N

Operating Temperature 0 ºC to +45 ºC

Storage Temperature -10 ºC to +70 ºC

et) 1.8Kg

Separate internal fuse. The input should be protected against lightning.

GB81

User’s Manual

12. Appendix

12.5 Glossary

1. DiSEqC (Digital Satellite Equipment Control)

A DiSEqC compatible receiver relies on a switching box which detects the 22kHz tone pulsing rapidly

on and o. In this way, a specially designed receiver can control numerous LNBs through a DiSEqC switching box.

2. Dolby Digital

An encoding system that digitally compresses up to 5.1 discrete channels of audio (left front, centre,

right front, left surround, right surround) into a single Bitstream. A low frequency eect (LFE) channel is included providing the sound needed for special eects.

3. DVB (Digital Video Broadcasting)

Set of standards that dene digital broadcasts using satellite, cable or terrestrial systems.

4. EPG (Electronic Programme Guide)

An electronic equivalent to a printed television listings magazine; it is an application used with

digital set-top boxes and digital television sets to list current and scheduled programs that are or will be available on each channel, including a short summary or commentary for each program. The information supplied in the EPG is sent and updated by the channel broadcaster.

5. FEC (Forward Error Correction)

A technique for error control of data transmission.

6. Frequency

The property of a signal measured in cycles per second (=Hz).

7. FTA (Free- To-Air)

An unscrambled broadcaster allowing customers to view channels or services without paying any

subscription.

8. Hi-Fi (High Fidelit

The characteristics of audio devices that can play back all the audio frequencies a person can detect,

which is the range of 16Hz~20KHz. Sometimes it is used to indicate good quality of audio devices such as stereo tape recorders.

9. LNB (Low Noise Block)

A device that is mounted on an arm facing your satellite dish, focusing on satellite signals. A LNB

converts signals received from satellite to a lower frequency and sends them to a satellite receiver via coaxial cable.

10. OSD (On Screen Display)

OSD displays the basic information necessary for the users to congure monitor or TV settings. OSD

information may include brightness, contrast, tuning, RGB adjustment, and screen size and position.

11. OTA (Over the Air)

A standard for the transmission of software for equipment, through a broadcast system. Manufacturers

reserve the right for deciding the release of the software for their products.

GB82

User’s Manual

12. Appendix

12. Polarisation

The direction of the electrical and magnetic elds of a signal. Satellites use both vertical and horizontal

polarisation. Means that a frequency can be used twice.

13. PID (Packet Identier)

A set of numbers identifying stream packets contained within a single data stream.

14. QPSK (Quaternary Phase Shift Keying)

Digital modulation technique in which the carrier phase can have one of four possible values.

15. RF (Radio Frequency)

Television signals are modulated onto RF signals and are then demodulated by your television’s or

STB’s tuner.

16. RF Modulator

Enables you to output the receiver’s digital signals to a TVs RF (Aerial) input, allowing you to connect

the receiver to a TV set without a SCART connection.

17. SCART

A 21-pin connector standard to connect two pieces of Audio-Visual equipment such as a TV and a VCR.

Each device will have a 21-pin female connection; a cable with male connection at both ends is used for connecting the devices.

18. Smartcard

A credit card sized card that contains updateable chip memory. It is used for accessing Pay TV

(encrypted) channel or services when inserted into an appropriate receiver.

19. S/PDIF (Sony/Philips Digital Interface format)

A standard format for the transfer of digital audio signals. It allows the transfer of digital audio

between two devices without any conversion to and from analogue, which could degrade the signal quality.

-Video (Super-Video)

20. S

Sometimes referred to as Y/C video; a technology for transmitting video signals via a cable. It is a video

signal transmission in which the luminance (brightness) and the chrominance (colour) signals are transmitted separately to achieve superior picture clarity.

21. Transponder

A satellite is divided up in parts called transponders. A transponder is one distribution section of the

satellite. Each transponder can be used for distribution of several channels or services.

GB83

User’s Manual

12. Appendix

12.6 Service and Support

Information concerning troubleshooting, software upgrade and product support is provided in the following websites and call centers. Should your product require warranty service, please contact HUMAX to obtain the appropriate authorization.

Deutschland

Tel: Önungszeiten: E-mail: Website:

Sprache:

Tel: Opening Hours: E-mail: Website: Language:

Australia

Tel: Opening Hours: E-mail: Website: Language:

01805-778870 (€ 0,14/Min) Mo-Fr 8:00-23:00 Uhr, Sa-So 8:00-20:00 Uhr support@humax-digital.de www.humax-digital.de Deutsch/Englisch

0870 247 8800 Mon-Fri 8:30-21:00 uksupport@humax-digital.co.uk www.humax-digital.co.uk English

1800 613 011 Mon- Fri 9:00-17:30 techinfoau@humaxdigital.com www.humaxdigital.com/australia English

Italia

Tel: Orario: Lingua:

Sverige

Tfn: Öppettider:

Språk:

GB84

User’s Manual

899 100 080 (€1+ VAT/min) Lun.-Ven. 8:00-18:00 Italiano

+46 (0)550 85527 Mån-fre 08:00-16:30 Svenska/engelska

12. Appendix

Suomi

Puh: Aukioloajat: Kieli:

Austria

Tel: Opening Hours: E-mail: Website: Language:

Note:

For hardware repair, please visit our website.

+358 9 56186 130 ma-pe 8:00-16:00 Suomi/Englanti

0820 400675 (€0,14/min) Mon-Sun 8:00-23:00 support@humax-digital.de www.humax-digital.de Deutsch/English

GB85

User’s Manual

12. Appendix

12.7 OPEN SOURCE SOFTWARE NOTICE

HUMAX products use certain open source operating system software distributed pursuant to GNU GENERAL PUBLIC LICENSE Version 2 and GNU LESSER GENERAL LICENSE Version 2.1 each as dened and published by the Free Software Foundation, Inc.

The following GPL and LGPL software source codes used in this product can be provided. Please contact us at gnu@humaxdigital.com.

GPL Software

linux

busybox

LGPL Software

uClibc

GB86

User’s Manual

12. Appendix

The GNU General Public License (GPL) Version 2, June 1991

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) oer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modied by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in eect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modication follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modication”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modication are not covered by this License; they are outside its scope. The act of

running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option oer warranty protection in exchange

for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) You must cause the modied les to carry prominent notices stating that you changed the les and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be

licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modied program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the

most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not

GB87

User’s Manual

12. Appendix

required to print an announcement.)

These requirements apply to the modied work as a whole. If identiable sections of that work are not derived from the Program,

and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to

exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program)

on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2

above on a medium customarily used for software interchange; or,

b) Accompany it with a written oer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing

source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the oer to distribute corresponding source code. (This alternative is allowed only for

noncommercial distribution and only if you received the program in object code or executable form with such an oer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modications to it. For an executable work, complete

source code means all the source code for all modules it contains, plus any associated interface denition les, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by oering access to copy from a designated place, then oering equivalent

access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is

intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of

any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

GB88

User’s Manual

12. Appendix

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new

versions will be similar in spirit to the present version, but may dier in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program species a version number of this License which applies to

it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are dierent, write to

the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED

BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER

PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source le to most eectively convey the exclusion of warranty; and each le should have at least the “copyright” line and a pointer to where the full notice is found.

One line to give the program’s name and a brief idea of what it does. Copyright (C) yyyy name of author This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as

published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software

Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type

`show w’. This is free software, and you are welcome to redistribute it under certain conditions; type `show c’ for details. The hypothetical commands `show w’ and `show c’ should show the appropriate parts of the General Public License. Of course, the

commands you use may be called something other than `show w’ and `show c’; they could even be mouse-clicks or menu items-

whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the

program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision’ (which makes passes at compilers) written by

James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this License.

GNU Lesser General Public License (LGPL)

Version 2.1, February 1999

GB89

User’s Manual

12. Appendix

Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the rst released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you rst think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object les to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we oer you this license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modied by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be aected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot eectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specied in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite dierent from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination ts its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modied version of the Library.

GB90

User’s Manual

12. Appendix

The precise terms and conditions for copying, distribution and modication follow. Pay close attention to the dierence between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or

other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”).

Each licensee is addressed as “you”. A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs

(which use some of those functions and data) to form executables. The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based

on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library

or a portion of it, either verbatim or with modications and/or translated straightforwardly into another language. (Hereinafter,

translation is included without limitation in the term “modication”.) “Source code” for a work means the preferred form of the work for making modications to it. For a library, complete source code

means all the source code for all modules it contains, plus any associated interface denition les, plus the scripts used to control

compilation and installation of the library. Activities other than copying, distribution and modication are not covered by this License; they are outside its scope. The act of

running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a

work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the

Library does and what the program that uses the Library does.

1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that

you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact

all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the

Library. You may charge a fee for the physical act of transferring a copy, and you may at your option oer warranty protection in exchange

for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and

distribute such modications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) The modied work must itself be a software library.

b) You must cause the les modied to carry prominent notices stating that you changed the les and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.

d) If a facility in the modied Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as

an argument passed when the facility is invoked, then you must make a good faith eort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-dened independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modied work as a whole. If identiable sections of that work are not derived from the Library,

and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to

those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a

work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees

extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to

exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a

volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To

do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version

2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you

can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all

subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form

under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable

source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software

interchange. If distribution of object code is made by oering access to copy from a designated place, then oering equivalent access to copy

GB91

User’s Manual

12. Appendix

the source code from the same place satises the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because

it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a “work that uses the Library” uses material from a header le that is part of the Library, the object code for the work may be

a derivative work of the Library even though the source code is not. Whether this is true is especially signicant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely dened by law.

If such an object le uses only numerical parameters, data structure layouts and accessors, and small macros and small inline

functions (ten lines or less in length), then the use of the object le is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6.

Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modication of the work for the customer’s own use and reverse engineering for debugging such modications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered

by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:

a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in

the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modied executable containing the modied Library. (It is understood that the user who changes the contents of denitions les in the Library will not necessarily be able to recompile the application to use the modied denitions.)

b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already

present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modied version of the library, if the user installs one, as long as the modied version is interface-compatible with the version that the work was made with.

c) Accompany the work with a written oer, valid for at least three years, to give the same user the materials specied in Subsection 6a, above, for a

charge no more than the cost of performing this distribution.

d) If distribution of the work is made by oering access to copy from a designated place, oer equivalent access to copy the above specied materials

from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for

reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally

accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:

a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be

distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to nd the

accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any

GB92

User’s Manual

12. Appendix

further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues),

conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is

intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of

any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the

original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such

new versions will be similar in spirit to the present version, but may dier in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library species a version number of this License which applies to

it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these,

write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY

APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY

OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source le to most eectively convey the exclusion of warranty; and each le should have at least the “copyright” line and a pointer to where the full notice is found. one line to give the library’s name and an idea of what it does.> Copyright (C) year name of author

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as

published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.

GB93

User’s Manual

12. Appendix

You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software

Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob’ (a library for tweaking knobs) written by James Random Hacker.

signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice

GB94

User’s Manual

Humax HD-FOX IR User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual