Humax HD-5500T User Manual

Download

HD Digital Receiver

User’s Manual

HD-5500T

The default password is 0000.

Notice

English

Thank you for purchasing a HUMAX product. Please read this user’s manual carefully to be able to safely install, use and maintain the product at maximum performance. Keep this user’s manual next to your product for future reference. The information in this user’s manual is subject to change without notice.

Not to be copied, used or translated in part or whole without HUMAX’s prior consent in writing except approval of ownership of copyright and copyright law.

Warranty

The warranty does not cover parts which may become defective due to misuse of the information contained in this manual.

Meaning of Symbols

To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualied service personnel.

This symbol indicates dangerous voltage inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Warnings, Cautions and Notes

Throughout the whole manual, pay special attention to the following marks that indicate hazardous situations.

Warning

Indicates a hazardous situation which could result in serious injury.

Caution

Indicates a situation which could damage the equipment or other apparatus.

Note

Indicates additional information to make the user aware of possible problems and information of any importance to help understand, use and maintain the installation.

Notice

‘WEEE’ Instructions

This product should not be disposed with other household wastes at the end of its working life. Please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. This will prevent possible harm to the environment or human health from uncontrolled waste disposal.

Domestic users: Please contact either the retailer where you purchased this product or their local government oce for details of where and how they can take this item for environmentally safe recycling.

Business users:

Contact your supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Trademarks

• Nagravision is a registered trademark of KUDELSKI S.A.

• Irdeto is a trademark of Irdeto Access B.V.

• Conax is a trademark of Telenor Conax AS.

• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Contents

English

Notice 1

Quick Start Guide

1. Checking Accessories 4

2. Product Overview

3. Connections

4. Powering On

5. Installation Wizard 1

6. Menu Overview 1

Basic Operation 13

Changing Channels 13 Volume / Mute / Audio 1 Display Format / Resolution 1 Programme Information (i-plate) 1 Subtitle 1 Text and Interactive Services 1

Channel List 17

Changing Channels 17 Editing Channels in Channel List 1

Managing Channels 19

Editing Channels 19 Editing Favourite Channels 2 Automatic Channel Numbering 2 Renew Channel Numbers 2

TV Guide 23

Watching Programmes 23 Setting Reminders 2 Finding Programmes 2 Scheduling Reminders 2

Installation 38

Automatic Search 38

Manual Search 3 Software Update (OTA) 3

Regular Auto Update 4

Antenna Power 4

Invisible Channel Search 4

Factory Default 4

System 43

System Information 43 Signal Detection 4

Power Management 4

Network 4

Pay Per View Services 45

6 6

MEDIASET PREMIUM 45 PANGEA 4 Irdeto Conditional Access 4 Conax Conditional Access 4

Appendix 48

Specication 48 Service and Support 4

Safety Warning 5

Trouble Shooting 5

Error Message 5 Glossary 5 OPEN SOURCE SOFTWARE NOTICE 5

4 5 6

9 9 1 1 2 2

3 4 4

6 7 7

9 0 2 4 6 8

Media List 27

Using Video List 29 Using Music List 3 Using Photo List 3

Preferences 33

Parental Control 33 Language Setting 3 Setting Power On/O Timer 3 Video Setting 3 Audio Setting 3 Screen Display 3 MHP Settings 3

0 1

4 4 5 6 7 7

Quick Start Guide

1. Checking Accessories

User’s Manual

Quick Start Guide

Remote Control

& Batteries

Manual &

Quick Start Guide

SCART Cable

Note: The accessories may vary according to area.

Customer information

concerning the „Application of the Directive 2008/103/CE regarding batteries, accumulators and the related waste disposal“.

Your remote control needs 2 batteries AAA type, 1,5VDC. The batteries included don’t contain mercury (Hg), cadmium (Cd) or lead (Pb). Do not mix dierent types of batteries or new and old batteries. Do not use rechargeable batteries. In order to avoid any risk of explosion, observe polarities indicated inside the battery compartment. Replace only with the type of batteries specied above. Do not throw them into re, do not recharge them. If you are not using the remote control for a long period of time, remove the batteries. Please respect the environment and prevalling regulations! Batteries must be collected separately from other refuse!

Quick Start Guide

2. Product Overview

Front Panel

STANDBY

Switches between operation and standby modes.

Status Display

English

RESET

Restart the receiver.

STANDBY/TV/RADIO LED

The light is emitted when the product is in each mode.

TV/RADIO

Guide

Arrows

Note: The image shown may dier from the actual product.

Rear Panel

VIDEO

ANTENNA IN

Connect a network cable.

ANTENNA OUT

Connect to the TV or VCR using an RF cable.

TV SCART

Connect to the TV using a TV SCART cable.

VCR SCART

Connect to the VCR or DVD using a VCR SCART cable.

Connect to the TV or VCR using an RCA cable.

AUDIO

Connect to the TV or VCR using an RCA cable.

HDMI

Connect to the TV using an HDMI cable.

Smartcard Slot

ETHERNET

Connect a LAN cable.

USB Port

Connect a USB storage device. (XviD, MP3 or JPEG)

SPDIF

Connect to the audio system using an S/PDIF cable. (digital audio)

Note: The image shown may dier from the actual product.

Quick Start Guide

Remote Control

MUTE Mutes audio.

STANDBY Switches between operation and standby modes.

SOURCE Controls the output of TV SCART.

mhp Displays MHP application information..

V-FORMAT Sets the resolution of video

WIDE Sets the display format.

NUMERIC Buttons

TEXT Enters the digital text service.

MENU Displays the main menu.

COLOUR Buttons

LIST Displays the channel list.

GUIDE Displays the programme guide.

ARROW Buttons

OK Selects a menu or con rms.

EXIT Exits all On-Screen Display (OSD) screens.

BACK

VOLUME Adjust the audio volume.

i(Information) Displays the channel and programme information.

OPT+ Displays the channels attributes.

P+/P- Changes the channel or page.

MyEPG Displays the MyEPG screen.

AUDIO Displays the audio list.

SUBTITLE Displays the subtitle language list

TV/RADIO witches between TV and radio modes.

Enter a TV/radio channel number.

Colour keys for interactive applications.

Moves the cursor up, down, left or right.

Returns to the previous screen.

Note: The image shown may di er from the actual product.

Inserting Batteries

1. Press the hook upward and lift the battery cover o .

2. Insert the batteries (supplied) matching the plus(+) and minus(-) at each end.

3. Close the cover.

i

Quick Start Guide

English

3. Connections

This section describes how to connect your product to match your particular devices setup and to gain optimum signal quality. The product provides various interfaces to connect to the TV, VCR or other devices. Select the most appropriate procedure depending on the device you have.

Note: If you encounter any problems setting up your product, please contact your local retailer or Humax

Customer Helpline.

SCART Cable

VCR SCART

Router

RCA Cable

Ethernet Cable

LAN

TV SCART

SCART Cable

S/PDIF Cable

HDMI

DVI Connecter

HDMI Cable

Quick Start Guide

Connecting the Antenna

Connect the aerial to the ANTENNA IN.

Connecting the TV and VCR

You can select one of the following connections depending on the device you have.

ݎTV with the HDMI connector;

For the best picture quality, connect the product and TV using an HDMI cable.

ݏTV with the DVI connector;

For very good picture quality, connect the product and TV using an HDMI cable and an HDMI-to-DVI converter for video and an RCA cable(Audio L/R) for audio.

ݐTV with the SCART connector;

For good picture quality, connect the product and TV using a SCART cable (TV SCART).

ݑTV with the SCART connector;

To output video and audio, connect the product and VCR using a SCART cable. (VCR SCART).

To make the audio connection, you can either

1. Connect the product and TV using an RCA cable (Audio L/R).

2. When using the digital audio system, connect the product and the digital audio system using an S/PDIF cable.

Note:

• Connecting your TV directly to the audio/video output of the product will assure a more vivid picture and enhance your viewing enjoyment.

• Programmes restricted by DRM (Digital Rights Management) may not be viewed via the HDMI cable. Connect using the SCART or RCA cable.

Connecting the Network

ݒConnecting to the LAN;

Connect one end of the Ethernet cable to the receiver and the other end to the LAN router.

Quick Start Guide

English

4. Powering On

1. Connect the power cord of the product to a wall outlet.

2. Power on by pressing the STANDBY button on the remote control or the STANDBY button at the front

of the product.

Quick Start Guide

5. Installation Wizard

When powering on your product for the rst time after purchase or performing the factory default in menu, the installation wizard will operate automatically.

Note: If you exit the installation wizard without fully completing the channel searching procedure, you

may not have all of the channels available. In this case, you can use the Settings > Installation menu to search for more channels.

1. Language

Select your language.

2. Display

Set the video output to your TV.

3. Antenna Power

Set the aerial power supply (5V Tuner).

Quick Start Guide

4. Automatic Channel Numbering

Set channels to be numbered automatically by

broadcaster.

5. Automatic Search

Channel search will begin automatically. Save the found channels when the search is

complete.

English

6. Congure Network

Congure the network setting for various

internet applications.

7. Result

The result of the Installation Wizard is shown. Select

Finish to exit the wizard.

Quick Start Guide

6. Menu Overview

Channel List

TV Guide

Video

Music

Photo

Settings

Pay Per View Services

Preference

• Parental Control

• Language

• Time

• Video

• Audio

• Screen Display

• MHP Settings

Edit Channels

• Edit Channel List

• Edit Favourite List

• Automatic Channel Numbering

• Renew Channel Numbers

Installation

• Automatic Search

• Manual Search

• Software Update

• Regular Auto Update

• Antenna Power

• Invisible Channel Search

• Factory Default

System

• System Information

• Signal Detection

• Power Management

• Network

How to Navigate

Displays the Menu OSD Moves among menus or options

Selects (Enters) a menu or conrms a selection Changes or adjusts the option

Returns to the previous screen Enters the number (0~9)

Exit all On-Screen

Basic Operation

Changing Channels

You can change the channels in several ways.

 Press the P/P button.  Enter the channel number directly. (0-9)  Go to the channel list or TV guide and select a channel.

Note: Press the TV/RADIO button to switch between TV and radio channels.

Volume / Mute / Audio

 To adjust the audio volume, press the +/- button.  To mute the audio temporarily, press the MUTE button.

Setting Audio Options

Audio options are available only when the programme supports multiple audio languages.

1. Press the AUDIO button.

2. Select the audio language.

3. Select the audio direction.

4. Press the

Note:

• The mute function remains set while you

change channels.

• You cannot set the audio direction when the

programme is broadcast in Dolby Digital.

OK button.

English

Display Select Conrm

Basic Operation

Display Format / Resolution

Setting Display Format

Press the WIDE button to set the display format according to the screen ratio. Each time you press this button, the value changes.

 Screen ratio 4:3: Auto - Letter Box - Centre  Screen ratio 16:9: Auto – Pillar Box – Zoom

Note: Refer to Display Format for details.

Setting Resolution

Press the V-FORMAT button to set the resolution of the screen. Each time you press this button, the value changes.

 576i - 576p - 720p - 1080i - Original

Display

Note: When connected with an HDMI cable,

you can only change to resolutions the TV supports.

Display

Basic Operation

English

Programme Information (i-plate)

The i-plate is an information banner that is displayed for a certain period of time whenever you change channels. Press the i button while watching a progamme to display the i-plate. Press the EXIT button to hide.

Playing time

Programme name Channel number and name

 Viewing detailed programme information

Press the i button again while the i-plate is displayed.

 Viewing previous/next programme information

Press the / button while the i-plate is displayed. Press the OK button to set reminders for future

programmes.

 Viewing programme information of other channels

Press the / button while the i-plate is displayed. Press the OK button to change to the selected channel.

Icons

Current time and date

Display Navigation mode

Signal strength and quality

Group name

Icons

The icons represent the information and services provided.

MHP application Teletext

Locked programme Resolution

Scrambled programme (CAS icons) HD programme

Parental guidance programme Multiaudio

Scheduled programme (Blue: Reminder)

Subtitle

Dolby Digital audio Dolby Digital Plus audio

Note: Programme information is not displayed when there is no programme information.

Basic Operation

Subtitle

You can select the subtitle language when subtitle information is provided.

1. Press the SUBTITLE button.

2. Select the subtitle language.

3. Select

4. Press the

Note: You can choose to always display the

Text and Interactive Services

If your chosen channel has digital teletext features, you can access them. Teletext services often load automatically shortly after the digital teletext window is displayed. In which case, simply follow the on screen instructions. (Press colour buttons)

1. Press the TEXT button to access digital teletext.

2. Press the

3. Press the

O to make the subtitle disappear.

OK button.

subtitle when available.

TEXT button again to return to normal viewing. P

/P button to exit this service..

Display Select Conrm

Note: The channel and volume cannot be controlled using the arrow buttons in interactive mode.

Channel List

The channel list will help you  nd the channel you want to watch quickly and easily.

You can access the channel list in several ways.

 Press the LIST button.  Press the MENU button and select Channel List.

Changing Channels

Select the channel you want to watch and press the OK button. The displayed channel will change.

Note:

• : Locked channel, : Scrambled channel (CAS icons)

• Press the i button to view the detailed programme information.

• Press the LIST or EXIT button to exit.

Advanced Options

Changing Group

You can display the list of the selected channel group.

 TV, HDTV, Radio, Favourite 1~5, Recent

1. Press the  button.

2. Select a channel group.

3. Press the OK button.

English

Note: Press the TV/RADIO button to switch

between TV and Radio groups.

Sorting Channels

Press the RED button to sort the list in numerical or alphabetical order.

Display/Change

Select Con rm

Channel List

Editing Channels in Channel List

You can lock, delete or rename each channel in the channel list, as well as in menu. To edit the multiple channels, go to the Settings > Edit Channels menu.

Locking / Deleting / Renaming Channels

1. Select a channel you want to edit and press the GREEN button.

2. Select an option.

 Lock: Select On or O.  Delete: Press the OK button.  Rename: Press the OK button and enter the

name in the keyboard.

3. Select OK to save and exit.

Note:

• Refer to

• The default password is 0000. If you have forgotten the password, please contact your local distributor.

Setting Favourite Channels

You can select your favourite channels and include them in the ve favourite groups.

1. Select a channel and press the

2. Select

3. Select a favourite group you want to include the channel in and press the

To remove a channel from a favourite group, select the group and press the

4. Select

Edit Channels for details.

Favourite.

OK to save and exit.

GREEN button.

GREEN

Display

Select Conrm

OK button.

OK button again.

Managing Channels

Editing Channels

The Edit Channel List menu will help you delete, move lock or rename multiple channels.

MENU  Settings  Edit Channels  Edit Channel List

Group name

Marked / Total channels

Function buttons

: Coloured or OPT+ button

English

Select

Note:

• : Locked channel, : Scrambled channel (CAS icons)

• The channels from 1 to 74 and 100 to 849 will not be listed. You can not edit those channels as the

channel numbers are automatically assigned.

• Press the MENU or EXIT button to exit. Press the BACK button to return to the previous screen.

Mark/Con rm Page up/down

Deleting Channels

1. Select the channels using the / and OK button.

2. Press the RED button.

Moving Channels

Channels can be moved only when Automatic Channel Numbering is set to O .

1. Select the channels using the / and OK button.

2. Press the GREEN button.

3. Move the selected channels to the location you want using the

/ and OK button.

Renumbering Channels

Channels can be renumbered only when Automatic Channel Numbering is set to On.

1. Press the GREEN button. The channels will be renumbered.

Managing Channels

Locking / Unlocking Channels

1. Select the channels using the / and OK button.

2. Press the

3. Select

Renaming Channels

1. Select a channel to rename.

2. Press the

3. Select

4. Enter the name in the keyboard.

Advanced Options

Changing Group

To list the channels of other groups, press the YELLOW button and select a group you want.

Note: Press the TV/RADIO button to switch between TV and Radio groups.

Changing Background

You can change the channel displayed in the background while editing.

1. Select the channel you want to watch.

2. Press the

OPT+ button.

Lock. To unlock, select Unlock.

OPT+ button.

Rename.

BLUE button. The displayed channel will change.

Selecting / Releasing All Channels

1. Press the OPT+ button.

2. Select

3. To release all, select

Select All.

Release All.

Managing Channels

Editing Favourite Channels

The Edit Favourite List menu will help you add or remove channels from the favourite groups.

MENU  Settings  Edit Channels  Edit Favourite List

Group name Marked / Total channels

Favourite group name

Function buttons

: Coloured or OPT+ button

English

Select

Note: Press the MENU or EXIT button to exit. Press the BACK button to return to the previous screen.

Mark/Conrm Page up/down

Adding / Removing Favourite Channels

1. Press the YELLOW button and select the favourite group you want to edit.

2. To add channels to the favourite list, select the channels you want to add using the

button in the left column and then press the RED button. The added channels will appear in the right column.

3. To remove channels from the favourite list, select the channels you want to remove in the right

column and then press the RED button.

/ and OK

Moving Channels

1. Select the channels using the / and OK button.

2. Press the

3. Move the selected channels to the location you want using the

Note: You can move the channels in the right column only.

GREEN button.

/ and OK button.

Managing Channels

Automatic Channel Numbering

MENU  Settings  Edit Channels  Automatic Channels Numbers

You can set the channels to be numbered automatically by broadcaster.

Select On to set the channel numbers automatically by broadcaster.

Whenever changing the value, the

Note:

terrestrial channels will be searched again.

Renew Channel Numbers

MENU  Settings  Edit Channels  Renew Channel Numbers

You can renew the channel numbers you edit.

Select Ye s and press the OK button to renew the channel numbers.

Note: This function is available only when

Automatic Channel Numbering is set to On.

TV Guide

English

The TV Guide is an on-screen guide of grid type which displays the programme information of channels in time and date order.

You can access the TV Guide in several ways.

 Press the GUIDE button.  Press the MENU button and select TV Guide.

Note: Press the GUIDE or EXIT button to exit. Press the BACK button to return to the previous screen.

Preview

Current time and date

Information of the selected programme: channel number & name,

programme name, simple information, favourite group, network type, and icons

Time bar

Function buttons

: Coloured button

Select

Tune/Reserve Page up/down

Note:

• Press the i button to view the detailed programme information.

• : Scheduled programme (Blue: Reminder)

: Present time, : DRM(Digital Rights Management) icon

Watching Programmes

1. Select a programme and press the OK button. The programme will be displayed in the preview.

2. Press the OK button again to exit the TV Guide and watch the programme.

TV Guide

Setting Reminders

1. Select a future programme and press the OK button.

2. Press the

The reserved programmes will be added automatically in

Note:

• If the programme is overlapped with another programme, adjust the reservation appropriately.

• If the channel is locked, you will be prompted to enter your password before watching. The default password is 0000. If you have forgotten your password, please contact your local distributor.

• In standby mode the product will switch on to the channel when the programme starts.

• You can reschedule reminders .(Refer to

Advanced Options

Quick Navigation

Press the

Changing Group

To list the channels of other groups, press the BLUE button and select a group you want.

Note:

• Press the

• To search specic programmes, go to

Finding Programmes.)

OK button again to cancel the reservation.

Schedule.

Scheduling Reminders.)

/ button to move to the previous/next programme.

TV/RADIO button to switch between TV and Radio groups.

Find Programmes by pressing the GREEN button. (Refer to

TV Guide

Finding Programmes

Find Programme will help you nd the programmes more specically using the keyword or genre.

By Keyword

1. Press the GREEN button.

2. Select

3. Select a keyword and press the

4. Press the

Note: To enter a new keyword, select New

By Genre

1. Press the GREEN button.

2. Select

3. Select a genre and press the

4. Select the specic genre and press the

Note:

• Press the

• You can set reminders for future programmes. (Refer to

Keyword and press the

YELLOW button to conrm.

Keyword.

Genre and press the

button. (if provided)

i button to view the detailed programme information. OK button to watch a found programme. (Refer to Changing Channels.)

 button.

OK button.

 button.

OK button.

GREEN

Display Conrm Select

Page up/down

Setting Reminders.)

English

TV Guide

Scheduling Reminders

Schedule lists reminders and will help you manage them in more detail.

1. Press the

2. You can add, edit or delete your reminders.

 To add, select New Reservation and press the

 To edit, select a reservation and press the OK

 To delete, select a reservation and press the BLUE

3. Reservation will pop up. You can change the options you want using the NUMERIC(0~9) and OK buttons.

4. Select

Note:

• Press the programme information.

• You can easily set reminders in TV guide, Find Programmes or i-plate navigation mode. (Refer to Setting Reminders, Find Programmes or Programme Information)

YELLOW button.

OK button.

button.

OK to save and exit.

i button to view the detailed

///,

YELLOW

Display Conrm Select

Page up/down

Media List

You can playback video, music or photo les.

 Go to MENU  Video/Music/Photo.

Switching Storage

1. Press the BLUE button to display the type of

storage.

2. Select the storage type and press the

button.

 USB: Displays each partition of the USB.  Network: The DLNA server is searched. Select the

type of the server.

Note:

• Only one USB icon will appear even when

there are more than one USB.

Switching Media

1. Press the YELLOW button to switch the media.

2. Select the media type and press the

button.

 Video, Music, Photo

English

Menu On/O Select Conrm Enter 0~9

Media List

Using the DLNA Server

You can have access to DLNA servers such as the PC or NAS (Network attached storage) and play the video, music or photo les. To connect to a DLNA server, the receiver must be connected to the local network.

Modem

HD-5500T

NAS

Playing Video Files in Network

1. Go to MENU>Video

2. Press the

BLUE button and select Network.

3. Select the DLNA server from the list and select the folder the video le is located in.

4. Select the video le and play the le.

Note:

• Playing music and photo les is similar as playing video les.

• You can download DLNA tools such as Media Server 11(http://www.microsoft.com/windows/ windowsmedia/it/player/11/default.aspx) and XBMC((http://www.xbmc.org). The software can be downloaded and updated in each website.

Menu On/O Select Conrm Enter 0~9

Media List

Using Video List

MENU  Video

Playing Files

Select a le and press the OK button. To select multiple les, select the les and press the RED button.

English

Path of folder

Storage

Function buttons

: Coloured button

Note:

• If a folder is selected, the le within the folder will not play unless it is selected.

• You will be prompted to enter the password when playing locked les.

• You can view Xvid les only.

Plays or pauses.

Jump to the previous scene.

Jump to the next scene.

Stops the playback of the current le and displays the list.

Fast Forward.

Fast Rewind.

Menu On/O Select Conrm Enter 0~9

Media List

Using Music List

MENU  Music

Playing Music Files

To play all les in the folder, press the OK button. If you want to play the selected les only, select the les and press the OK button.

Path of folder

Storage

Title, artist, album

Function buttons

: Coloured button

Music Player

The music player is displayed while playing back a music le.

Plays or pauses

Plays the previous le

Plays the next le

Stops the music player and displays the list.

Changes the play mode (Once, Repeat, Repeat All, Shue)

Menu On/O Select Conrm Enter 0~9

Media List

English

Using Photo List

MENU  Photo

Photo Slideshow

To slideshow all photos in the folder, press the OK button. If you want to slideshow the selected photos only, select the photos and press the OK button.

Path of folder

Storage

Thumbnail

Function buttons

: Coloured or OPT+ button

Pauses slideshow.

Shows the next photo.

Shows the previous photo.

Stops the slideshow and displays the list.

Info Banner

Press the OK button to pause the slideshow and display the information banner.

Menu On/O Select Conrm Enter 0~9

Media List

Slide Mode

1. Press the OPT+ button.

2. The

Slide Mode is displayed.

 Display Time: The duration the photo is

displayed.

 Music Play: Determines whether to play music

le during slideshow or not.

 Folder: The folder the music le is located in.

Press the OK button to display the list of music les and select a folder.

Menu On/O Select Conrm Enter 0~9

Preferences

English

In this chapter you can set options for parental control, language, time, video, audio, screen display and MHP settings.

Note: Press the MENU or EXIT button to exit. Press the BACK button to return to the previous screen.

Parental Control

MENU  Settings  Preferences  Parental Control

You will be prompted to enter the password to access this menu.

Note: The default password is 0000. If you have forgotten your password, please contact your local

distributor.

Maturity Rating

1. Select

2. Select an option.

2. Press the OK button.

Maturity Rating.

 View All  7, 12, 14, 18 : Blocks the programmes for

viewers under the age limit

 Lock All

Note: You will be prompted to enter

the password to view the blocked programmes.

Changing Password

You can change the current password. This password is prompted every time a password blocked menu is accessed.

1. Select

2. Enter the new password.

3. Enter the new password for verication.

Change Password.

Menu On/O Select Conrm Enter 0~9

Preferences

Language Setting

MENU  Settings  Preferences  Language

You can set the language for system, audio and subtitle.

1. Select the language type.

 System Language  Audio Language  Subtitle Language

2. Select the language.

Note:

• You can change the audio or subtitle language by pressing the AUDIO or SUB button while watching a programme.

• If you select subtitle will not be displayed.

Setting Power On/O Timer

MENU  Settings  Preferences  Time

O in subtitle language, the

1. To turn on the product automatically, select

2. Enter the time.

3. Set the options for the power on timer.

 Channel: Select the channel to be displayed

when powering on.

 Volume: Adjust the volume of the audio when

powering on.

 Repeat: Select the repeat mode of the power on

timer.

4. To turn o the product automatically, select Power O Timer and select Set Timer.

5. Enter the time.

Note:

The power on time and power o time should be set dierent from each other.

Menu On/O Select Conrm Enter 0~9

Power On Timer and select Set Timer.

Preferences

English

Video Setting

MENU  Settings  Preferences  Video

Setting TV Screen Ratio

You can select the screen ratio of your TV.

1. Select Screen Ratio.

2. Select an option.

 16:9 - 4:3

Setting Display Format

You can select the display format according to the screen ratio of your TV.

1. Select

2. Select an option.

Note: You can set the display format by pressing the WIDE button while watching a programme. Refer to

Screen ratio Display Format

Display Format.

 Screen ratio 4:3: Auto - Letterbox - Centre  Screen ratio 16:9: Auto - Pillarbox - Zoom

Display Format / Resolution.

4:3

Auto Letterbox Centre

16:9

Auto Pillarbox Zoom

Setting Letter and Pillar Box Colour

You can set the colour for the margin space according to the display format.

1. Select

Letter & Pillar Box Colour.

2. Select an option.

 Black - Grey

Setting TV SCART / VCR SCART

You can select the video signal output option for the TV SCART or VCR SCART.

1. Select TV SCART or VCR SCART.

2. Select an option.

 TV SCART: CVBS – S-Video – RGB  VCR SCART: CVBS – S-Video

Menu On/O Select Conrm Enter 0~9

Preferences

Audio Setting

MENU  Settings  Preferences  Audio

Setting Digital Audio Output

You can select the digital audio signal output of your product.

1. Select Digital Audio Output.

2. Select an option.

 Stereo - Multi-channel

Audio Input Digital Audio Output

Dolby Digital Dolby Digital

Dolby Digital Plus Dolby Digital

MPEG PCM

HE-AAC Dolby Digital

Setting Lip-Sync

You can adjust the sound dierence of audio and video.

1. Select

2. Adjust the lip-sync using the

Lip-Sync.

/ button. Pressing the right button increases the audio speed and

pressing the left button decreases it.

Menu On/O Select Conrm Enter 0~9

Preferences

Screen Display

MENU  Settings  Preferences  Screen Display

Setting Info Display Time

You can set the duration the information box is displayed every time the channel is switched.

1. Select Info Display Time.

2. Select an option.

 O - 1~20 sec

Setting Transparency

You can set the transparency of the On-Screen Display.

1. Select

2. Select an option.

Setting Subtitle Font

You can adjust the subtitle font.

1. Select Subtitle Font.

2. Select an option.

Transparency.

 O - 25% - 50% - 75%

 Variable - Fixed

English

MHP Settings

MENU  Settings  Preferences  MHP Settings

You can set MHP applications.

Select MHP Settings

 Display by MHP App.: Display i-plate when

changing channels.

 MHP Logo: Display MHP logo.  Auto-Start MHP App.: Start interactive MHP

application automatically.

 MyEPG: Use a TV guide supported by MHP

application.

Menu On/O Select Conrm Enter 0~9

Installation

Installation menu allows you to search the available TV and radio channels. Software update, antenna power and factory default setting are also available in this section.

MENU  Settings  Installation

Note:

• You will be prompted to enter the password to access this menu. The default password is 0000. If you have forgotten your password, please contact your local distributor.

• Press the button to exit.

Automatic Search

You can search channels automatically without entering any other information.

1. Select starts.

2. Select the results.

Note: Select Stop and press the OK button to

BACK button to save the changes and return to the previous screen. Press the MENU or EXIT

Automatic Search. Channel search

Save and press the OK button to save

stop the channel search.

Menu On/O Select Conrm Enter 0~9

Installation

English

Manual Search

You can search channels manually by searching parameters.

1. Select Manual Search.

2. Congure the search options.

 Channel: Select the channel.  Frequency: Enter the frequency.  Bandwidth: Select the bandwidth.  Network Search: Select On or O.

3. Select Search and press the OK button.

4. Select

Note: Select Stop and press the OK button to

Software Update (OTA)

In order to maintain proper performance of the product, it is essential to have the most up-to-date software. Please refer to http://www.mediasat.com for software update. It is recommended that you periodically check for the availability of software update. OTA, an abbreviation of Over–the-Air, means that the software can be downloaded through your aerial. The manufacturer reserves the right to decide when and where to release software by this process. You can also search and download new software manually.

Save and press the OK button to save

the results.

stop the channel search.

MENU  Settings  Installation  Software Update

Automatic Update

1. Select Automatic Update and press the OK button to search for new software.

2. When new software is detected, select Ye s to start the update process now.

Menu On/O Select Conrm Enter 0~9

Installation

Manual Update

1. Select Manual Update and press the OK button.

2. Enter the options manually.

 Channel: Select the channel.  Frequency: Enter the frequency. The

corresponding frequency value will be automatically displayed.

3. Select Search and press the OK button to search for new software.

4. When new software is detected, select start the update process now. Please wait until the update is complete. When completing the software update, the product is automatically powered o and on again.

Note:

• It may take 5~10 minutes to update software.

• Other functions such as scheduling programmes will not activate while software update takes place.

• Be sure to update software when the signal strength and quality is high. If the weather is not favorable and the signal strength and quality are not recommendable, perform the software update later.

• The product will search new software automatically during standby. If new software is detected, you can choose either to download immediately or later when you switch into operation mode. If you select Later, the message will be displayed again when you power on.

Caution:

• Please be careful to keep the power on and the power cord plugged in during software update. If the power is o during software update, fatal damage may be caused to the product.

• Please be careful not to pull out the signal line (RF cable) during software update. Update may be interrupted and the product may not operate.

Ye s to

Menu On/O Select Conrm Enter 0~9

Installation

Regular Auto Update

MENU  Settings  Installation  Regular Auto Update

You can set to update the channel and software regularly

1. Select Regular Auto Update.

2. Set the options.

3. Select

Antenna Power

MENU  Settings  Installation  Antenna Power

Manual Update if you want to update

the software by entering the options manually.

 Update Target: Select All, Channel or Software.  Auto Search in Standby: Select On or O.  Auto Search in Operate: Select On or O.  Search Time: Enter the search time.  Frequency: Select Daily or Weekly

English

Active antenna is a portable or indoor antenna which needs power supply from the product because it does not have power cord for itself. Connect an active antenna to the ANTENNA IN on the rear of the product.

1. Select 5V Antenna Power

2. Select an option.

 On: 5V power is supplied from the active antenna

cable.

 O: No power supplied

Menu On/O Select Conrm Enter 0~9

Installation

Invisible Channel Search

MENU  Settings  Installation  Invisible Channel Search

You can set to search the invisible channels during channel search.

1. Select Invisible Channel Search.

2. Select an option.

 On - O

Factory Default

MENU  Settings  Installation  Factory Default

1. Select

2. Select

3. You will be prompted to enter the password.

Factory Default. Ye s .

Enter the password.

Menu On/O Select Conrm Enter 0~9

System

English

In System, system information, signal detection, power management and network options are available.

Note: Press the MENU or EXIT button to exit. Press the BACK button to return to the previous screen.

System Information

MENU  Settings  System  System Information

The system information is displayed.

Signal Detection

MENU  Settings  System  Signal Detection

You can check the signal strength and quality of the searched channels.

Menu On/O Select Conrm Enter 0~9

System

Power Management

MENU  Settings  System  Power Management

Setting Power Saving in Standby

You can minimise the standby power consumption to below 1W.

1. Select Power Saving in Standby.

2. Select

Network

MENU  Settings  System  Network

Conguring IP (LAN)

1. You can congure the Ethernet setting

Select Apply and press the OK button.

On to deactivate the certain features

and minimise the power consumption.

options.

 DHCP: Apply the options according to the DHCP.  Manual: Enter the options manually,

Note: When entering the IP address manually,

enter 3 digits in a row.

Menu On/O Select Conrm Enter 0~9

Pay Per View Services

English

You can use Mediaset Premium and PANGEA service only when you tune to Mediaset Pay TV channels or PANGEA channels.

MEDIASET PREMIUM

MENU  Pay Per View Services  MEDIASET PREMIUM

Card Information

1. Select

2. The card information is displayed.

Purchase history

1. Select SELCTED PROGRAMS.

2. The list of purchased programs is displayed.

Viewing recharge history

1. Select RECHARGE HISTORY.

2. The recharge history is displayed.

Purchasing program package

1. Select PACKAGE PURCHASE.

2. Select the program package you want.

3. Press the

4. Press the

5. Press the

CARD INFORMATION.

GREEN button to view the

description of the program.

OK button to view the terms of

service.

OK button to conrm.

Menu On/O Select Conrm Enter 0~9

Pay Per View Services

PANGEA

MENU  Pay Per View Services  PANGEA

Purchasing the programs

1. Select

2. Select the genre.

3. Select the program you want.

4. Press the

5. Press the

6. Press the

Purchase history

1. Select PURCHASED PRODUCTS.

2. The list of purchased programs is displayed.

Card Information

1. Select SMARTCARD INFORMATION.

2. The smartcard information is displayed.

Recharge Information

1. Select

2. The recharge information is displayed.

PRODUCTS CATALOGUE.

GREEN button to view the

description of the program.

OK button to view the purchase

conditions.

OK button to conrm.

RECHARGE INFORMATION.

Menu On/O Select Conrm Enter 0~9

Pay Per View Services

Irdeto Conditional Access (Irdeto Smartcard User Only)

MENU  Pay Per View Services  Irdeto Conditional Access

Conditional Access

You can check the information of the Irdeto Conditional Access.

1. Select Conditional Access.

2. Select the item you want.

 Smart Card Status  Softcell Service Status  Loader Status  Components

3. The information of the selected item is

displayed

Mail Messages

You can receive mails from the broadcasting company.

1. Select

2. Select a mail to read then press the The message will be displayed.

Note:

• When a new mail arrives, the envelope icon will appear.

• Old mails will be deleted automatically when your mail box is full

Mail Messages.

OK button.

English

Conax Conditional Access (Conax Smartcard User Only)

MENU  Pay Per View Services  Conax Conditional Access

Conditional Access

You can check the information of the Conax Conditional Access.

1. Select

2. The information of the conditional access is

Conditional Access.

displayed.

Menu On/O Select Conrm Enter 0~9

Appendix

Speci cation

Tuner & Channel

Input Connector

Frequency Range

Signal Level

Demodulation

Mode

FEC Mode

Guard Intervals

Antenna Power 5V 50mA Max.

Audio/Video Decoding

Audio Decoding

Audio Mode

Video Decoding

Video Format

Video Resolution

IEC 169-2 Female

174MHz to 230MHz 470MHz to 862MHz

-10 to -70 dBm

OFDM

2K, 8K

1/2, 2/3, 3/4, 5/6, 7/8

1/4, 1/8, 1/16, 1/32

Dolby Digital Plus

Single channel/Dual channel/Joint stereo/Stereo

HD MPEG2 /SD MPEG2 / MPEG4(H.264/AVC)

4:3, 16:9, Letter Box

1080i, 720p, 576p, 576i

Memory

Flash Memory

RAM

EEPROM

Audio/Video In/Out

Video

Audio

Data In/Out

USB

32MB MB

256MB

8KB

TV-SCART, VCR-SCART, RCA, HDMI/HDCP

TV-SCART, VCR-SCART, Audio L/R, S/PDIF (Digital Audio Output)

USB 2.0 Host (5 V 500, 250mA Max.)

Appendix

English

RJ-45

Power Supply

Input Voltage

Typ e

Power Consumption

Protection

Physical Specication

Size (w/h/d)

Weight

Operating Temperature

The specications are subject to change without notice.

Note:

Ethernet 10/100Mbps

90-250V a.c., 50/60Hz

SMPS

Max. 16W (Standby: 0.8W)

Separate internal fuse. The input should be protected against lightning.

280mm x 45mm x 200mm

1.42Kg

0 ºC to +45 ºC

Service and Support

Information concerning troubleshooting, software upgrade and product support is provided in the following websites and call centers. Should your product require warranty service, please contact HUMAX to obtain the appropriate authorization.

Call Center

Service customers

Modernizations generic and technical software, information http://www.mediasat.com (technical area) Italiano

Technical Hotline: 899 100080

This service is charged with a cost per minute of 1.€+VAT. The service is not enabled for Omnitel users.

Appendix

Safety Warning

This product has been manufactured to comply with international safety standards. Please read the following safety precautions carefully.

Safety Instructions and Precautions

1. MAINS SUPPLY

• Operate this product only from the type of power supply indicated on the marking label. If you are not sure of

the type of power supplied to your home, consult your local power company.

• Disconnect the product from the mains before you start any maintenance or installation procedures.

2. OVERLOADING

• Do not overload a wall outlet, extension cord or adapter as this may result in electric re or shock.

3. LIQUID

• The product should not be exposed to liquid of any kind. In addition, no objects lled with liquid should be

placed on the apparatus.

4. CLEANING

• Disconnect the product from the wall outlet before cleaning.

• Use a light damp cloth (no solvents) to dust the product.

5. VENTILATION

• The slots on top of the product must be left uncovered to allow proper airow into the unit.

• Do not stand the product on soft furnishings or carpets.

• Do not stack electronic equipments on top of the product.

6. ATTACHMENTS

• Do not use any unsupported attachments as these may be hazardous or cause damage to the product.

7. LIGHTNING, STORM OR NOT IN USE

• Unplug the product from the wall outlet and disconnect the antenna during a thunderstorm or when left

unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and power-surges.

8. EXTRANEOUS OBJECTS

• Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or

damage parts.

9. REPLACEMENT OF PARTS

• When replacement of parts is required, be sure the service technician uses replacement parts specied by the

manufacturer or those that have the same characteristics as the original part. Unauthorized substitution may result in additional damage to the unit.

10. CONNECTION

[Satellite] CONNECTION TO THE SATELLITE DISH LNB

• Disconnect the product from the mains before connecting or disconnecting the cable from the satellite dish.

Failure to do so can damage the LNB.

[Cable] CONNECTION TO THE CABLE TV SIGNAL

• Connect all components before plugging any power cords into the wall outlet. Always turn o the product, TV

and other components before you connect or disconnect any cables.

[Terrestrial] CONNECTION TO THE AERIAL

• Disconnect the product from the mains before connecting or disconnecting the cable from the aerial. Failure to

do so can damage the aerial.

Appendix

11. CONNECTION TO THE TV

• Disconnect the product from the mains before connecting or disconnecting the cable from the TV. Failure to do so can damage the TV.

12. EARTHING

[Satellite] The LNB cable must be earthed to the system earth for the satellite dish.

13. LOCATION

• Place the product indoors to avoid exposing it to lightning, rain or sun. Do not place it near a radiator or heat register.

• We recommend that the product has 10 cm clearance from any other appliances susceptible to electromagnetic inuences, such as a TV or a VCR.

• Do not block the openings with any object, and do not place the product on a bed, sofa, rug, or other similar surface.

• If you place the product on a rack or a bookcase, ensure that there is adequate ventilation and that you have followed the manufacturer’s instructions for mounting.

• Do not place the product on an unstable cart, stand, tripod, bracket, or table where it can fall. A falling product can cause serious injury to a child or adult, and serious damage to the appliance.

Warning

1. To avoid damage of the power cord or plug;

• Do not modify or process the power cord or plug arbitrarily.

• Do not bend or twist the power cord.

• Make sure to disconnect the power cord holding the plug.

• Keep heating appliances as far as possible from the power cord in order to prevent the cover vinyl from melting.

• The mains plug, as a disconnection device, shall remain readily accessible by the user.

2. To avoid electrical shock;

• Do not open the main body.

• Do not insert metal or inammable objects inside the product.

• Do not touch the power plug with wet hands.

• Disconnect the power cord in case of lightning.

3. To avoid damage of product;

• Do not use the product when it is out of order. If you continue to use the product when defective, serious damage can be caused. Make sure to contact your local product distributor if the product is out of order.

• Do not insert metal or alien substance into the slots for the modules or Smartcards. (where applicable) It may cause damage to the product and reduce its life span.

4. To avoid damage of the hard disk drive (PVR only)

• Do not move the product or turn the power o suddenly while the hard disk drive is running.

• The company shall not be liable for any corruption of data on the hard disk drive caused by carelessness or misuse.

English

Appendix

Trouble Shooting

Before contacting your local service centre, please read the tips below carefully. If the problem persists after completing the following procedure, please contact your local product distributor or service centre for further instructions.

1. No message displayed on the front display. (The product will not switch on.)

• Check the main power cable and make sure it is plugged into a suitable power outlet.

• Check that the mains supply is switched on.

• Connect the power cable to a dierent power outlet.

• Check that the power switch is on at the rear of the product. (where applicable)

2. No picture

• Make sure that the product is powered on and in operation mode. (Press the STANDBY button)

• Make sure that the AV cable is rmly connected to the TV.

• Make sure that the antenna cable is properly connected to the product.

• Be sure to activate channel search.

• Check the brightness level of the TV.

• Check if the channel is currently on air. Contact the broadcaster to ensure that the channel is running.

• Press the SOURCE button if the product is in external input mode. (where applicable)

• Satellite: Make sure that the antenna setting in the menu is correct.

3. Poor picture/sound quality

• Install the antenna in an obstacle-free place.

• Make sure there is no mobile phone or microwave oven near the product.

• Keep the power and the antenna cables apart from each other.

• Check the signal levels and adjust your antenna if the level is too low. The signal level may be aected by weather conditions.

Note: If the antenna is covered with snow or the RF is weakened by heavy rain, the condition of the

sound and picture may temporarily be poor. However, the poor sound and picture quality due to weather conditions cannot be accepted as a malfunction of product.

• [Satellite] Check that your dish alignment is correct.

• [Satellite] Change the satellite dish for a larger one as this will increase the signal levels received.

• [Satellite] Replace the LNB with a lower noise factor in cases where the noise factor is too high.

• [Satellite] Replace the LNB with a new one in case it is damaged or out of order.

• [Terrestrial] Adjust the antenna direction to get a better picture.

• [Terrestrial] Set the antenna power in menu to On, if you use the active antenna to improve the reception. (where applicable)

4. No or poor sound

• Check that your AV cable is connected correctly.

• Check the volume levels of your TV set and the product.

• Check if the product or TV is on mute.

• Check audio type or soundtrack option in the AV menu. (where applicable)

5. Remote control does not operate.

• To control the product, the top end of the remote control should point directly towards the receiving part of the product.

• Remove and reinsert the batteries in the remote control.

• Replace the batteries in the remote control for a new set.

• Set the remote control to STB or PVR mode, if you are using the universal remote control. (where applicable)

Appendix

6. Cannot make reservations.

• Check that no previous reservations are conicting with the new reservation.

7. No password information is given.

• The default password is always 0000.

8. Channel search does not work.

• Satellite: Make sure that the antenna setting in the menu is correct.

• Terrestrial: Make sure that the antenna is connected correctly.

• Terrestrial: Use the appropriate antenna capable of receiving VHF or UHF channels for your area.

9. Cannot update new software.

• You can get an update. If the product does not show a message requesting update, this means no software is available.

10. Cannot watch scrambled channels.

• Check that you have the appropriate Smartcard or CI-Module. Reinsert the Smartcard or CI-Module and make sure it initialises correctly.

• Check in the menu that the product is detecting the Smartcard or CI-Module.

• Check in the menu that you have a valid and working subscription to the channels you wish to view.

• Ensure that the Smartcard or CI-Module is not damaged.

11. Cannot watch pay channels.

• Check in the menu that you have a valid and working subscription to the channels you wish to view.

• Contact your network operator for more information.

12. The product makes a humming noise.

• The noise is from the fan; the hard disk is operating normally. This kind of noise is inevitable but seldom noticeable.

13. Cannot record progammes. (PVR only)

• The hard disk is full. Delete unnecessary programmes and make space for new recording.

• Check if recording is overlapped with another channel. Stop the current recording or wait until the recording is nished.

• Check that the product is switched on when recording starts.

14. Cannot operate TSR (Time Shifted Recording). (PVR only)

• TSR may not be available during recording. Wait until recording is nished.

• Delete unnecessary programmes and make space for new recording.

15. Cannot playback. (PVR only)

• To playback the recorded le of a scrambled channel, use the Smartcard. In case it has been a long time since you last recorded, this may not work. Contact the product distributor.

• The signal during recording may be weak or the hard disk too full.

16. Cannot change channels while recording. (PVR only)

• Certain channels may not be changed due to restriction of the tuner or connection type.

English

Appendix

Error Message

Error message Possible causes What to do

The satellite dish is not pointing at the satellite.

No or bad signal [Satellite]

No or bad signal [Cable]

No or bad signal [Terrestrial]

The channel is scrambled or not available.

The audio is not available.

No access

No card inserted. Smartcard is not inserted. Insert Smartcard.

Signal is too weak.

Satellite dish is too small. Change to a larger dish.

Problem with LNB. Change the LNB.

Wrong antenna setting. Set the antenna correctly.

The cable is not connected.

The cable may be damaged or defective.

The channel is not broadcasting. Exchange the cable.

The aerial is not pointing properly.

The channel has a signal, but no audio or video.

The channel has been deleted by the broadcasting company.

The channel is for data broadcasting.

The channel has a video signal, but no audio.

No access

No authorization.

Adjust dish alignment.

Increase the LNB voltage or connect a signal amplier.

Make sure the cable is connected correctly.

Exchange the cable.

Adjust aerial. Check the cable from the aerial. If you cannot resolve the problem, you may need to have your aerial and installation tested by a professional.

Conrm if the channel is currently on air.

Check if the channel is currently on air

Remove the channel from the channel list and check for new transponder details.

Press the audio button to conrm that the channel has audio options.

Make sure you are subscribed to the channel.

If the product has been turned o for a long time (standby or power o), please wait for authorization. It may take up to 60 minutes.

Appendix

Error message Possible causes What to do

Wrong Smartcard is inserted. Insert the correct Smartcard.

English

Incorrect card

CI-Module not installed.

Invalid CI-Module

Short LNB [Satellite]

Smartcard is not inserted correctly. Remove the Smartcard and reinsert it.

Smartcard is damaged.

CI-Module is not inserted. Insert CI-Module.

CI-Module is not inserted correctly. Remove the CI-Module and reinsert it.

CI-Module is not recognized.

Wrong CI-Module. Insert the correct CI-Module.

CI-Module is damaged. Replace the CI-Module.

LNB cable is short. Replace LNB cable.

LNB is internally short. Replace LNB.

Alien substance is inserted in the LNB IN port. The port may be damaged.

Contact your Smartcard retailer or channel broadcaster for a Smartcard replacement.

Insert a dierent CI-Module to check if your existing module is working.

Remove the alien substance and contact the local service centre in case damaged has occurred.

Appendix

Glossary

CVBS (Composite Video Baseband Signal)

A technology for transmitting video signals via a cable. Mixes luminance (brightness) and the chrominance (colour) signals together.

DiSEqC (Digital Satellite Equipment Control)

A DiSEqC compatible receiver relies on a switching box which detects the 22kHz tone pulsing rapidly on and o. In this way, a specially designed receiver can control numerous LNBs through a DiSEqC switching box.

Dolby Digital

An encoding system that digitally compresses up to 5.1 discrete channels of audio (left front, centre, right front, left surround, right surround) into a single Bitstream. A low frequency eect (LFE) channel is included providing the sound needed for special eects.

DVB (Digital Video Broadcasting)

Set of standards that dene digital broadcasts using satellite, cable or terrestrial systems.

EPG (Electronic Programme Guide)

An electronic equivalent to a printed television listings magazine; it is an application used with digital set-top boxes and digital television sets to list current and scheduled programs that are or will be available on each channel, including a short summary or commentary for each program. The information supplied in the EPG is sent and updated by the channel broadcaster.

FEC (Forward Error Correction)

A technique for error control of data transmission. Frequency The property of a signal measured in cycles per second (=Hz).

FTA (Free- To-Air)

An unscrambled broadcaster allowing customers to view channels or services without paying any subscription.

HDD (Hard Disk Drive)

The primary computer storage medium, which is made of one or more aluminum or glass platters, coated with a ferromagnetic material.

Hi-Fi (High Fidelity)

The characteristics of audio devices that can play back all the audio frequencies a person can detect, which is the range of 16Hz-20KHz. Sometimes it is used to indicate good quality of audio devices such as stereo tape recorders.

LNB (Low Noise Block)

A device that is mounted on an arm facing your satellite dish, focusing on satellite signals. A LNB converts signals received from satellite to a lower frequency and sends them to a satellite receiver via coaxial cable.

NVOD (Near Video On Demand)

A technology that allows customers to view the start of popular programmes or lms within a short period from the time they make their selection. This is possible as the broadcaster sends multiple copies with staggered start times.

OSD (On Screen Display)

OSD displays the basic information necessary for the users to congure monitor or TV settings. OSD information may include brightness, contrast, tuning, RGB adjustment, and screen size and position.

OTA (Over the Air) A standard for the transmission of software for equipment, through a broadcast system. Manufacturers reserve the right for deciding the release of the software for their products.

PID (Packet Identier)

A set of numbers identifying stream packets contained within a single data stream.

PIP (Picture In Picture)

A function that allows you to display two dierent TV channels (or TV inputs) on a single screen.

Appendix

English

Polarisation

The direction of the electrical and magnetic elds of a signal. Satellites use both vertical and horizontal polarisation. Means that a frequency can be used twice.

PVR (Personal Video Recorder)

Video recorder that can record and playback programmes directly using the embedded hard disk drive(s).

QPSK (Quaternary Phase Shift Keying)

Digital modulation technique in which the carrier phase can have one of four possible values.

RF (Radio Frequency)

Television signals are modulated onto RF signals and are then demodulated by your television’s or STB’s tuner.

RF Modulator

Enables you to output the receiver’s digital signals to a TVs RF (Aerial) input, allowing you to connect the receiver to a TV set without a SCART connection.

RGB (Red – Green – Blue)

A technology for transmitting video signals via a cable. RGB is a system to represent red, green, and blue colours on a TV or monitor display. Red, green, and blue can be combined in various proportions to obtain any colour.

RS-232C

A connection to allow you to connect to a PC to update receiver’s software.

SCART

A 21-pin connector standard to connect two pieces of Audio-Visual equipment such as a TV and a VCR. Each device will have a 21-pin female connection; a cable with male connection at both ends is used for connecting the devices.

Smartcard

A credit card sized card that contains updateable chip memory. It is used for accessing Pay TV (encrypted) channel or services when inserted into an appropriate receiver.

S/PDIF (Sony/Philips Digital Interface format)

A standard format for the transfer of digital audio signals. It allows the transfer of digital audio between two devices without any conversion to and from analogue, which could degrade the signal quality.

S-Video (Super-Video)

Sometimes referred to as Y/C video; a technology for transmitting video signals via a cable. It is a video signal transmission in which the luminance (brightness) and the chrominance (colour) signals are transmitted separately to achieve superior picture clarity.

Transponder

A satellite is divided up in parts called transponders. A transponder is one distribution section of the satellite. Each transponder can be used for distribution of several channels or services.

Trick-Play

Pause, Fast Forward/Fast Rewind, Slow Motion, Instant Replay, Commercial Skip, Repeat A-B.

TSR (Time Shifted Recording)

A function that records the present programme temporarily to support trick-play.

Appendix

OPEN SOURCE SOFTWARE NOTICE

HUMAX products use certain open source operating system software distributed pursuant to GNU GENERAL PUBLIC LICENSE Version 2 and GNU LESSER GENERAL LICENSE Version 2.1 each as dened and published by the Free Software Foundation, Inc.

The following GPL and LGPL software source codes used in this product can be provided. Please contact us at gnu@humaxdigital.com.

GPL Software

linux busybox avinfo e2fsprogs

This package, the ext2 lesystem utilities, are made available under the GNU Public License version 2, with the exception of the lib/ext2fs and lib/e2p libraries, which are made available under the GNU Library General Public License Version 2, the lib/uuid library which is made available under a BSD-style license and the lib/et and lib/ss libraries which are made available under an MIT-style license.

LGPL Software

uClibc libexif id3lib

FreeType License (FTL) Software

freetype

Appendix

English

The GNU General Public License (GPL) Version 2, June 1991

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) oer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modied by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in eect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modication follow.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modication”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modication are not covered by this License; they are outside its scope. The act of

running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option oer warranty protection in exchange

for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) You must cause the modied les to carry prominent notices stating that you changed the les and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be

licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modied program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the

most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modied work as a whole. If identiable sections of that work are not derived from the Program,

and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other

Appendix

licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to

exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program)

on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2

above on a medium customarily used for software interchange; or,

b) Accompany it with a written oer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing

source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the oer to distribute corresponding source code. (This alternative is allowed only for

noncommercial distribution and only if you received the program in object code or executable form with such an oer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modications to it. For an executable work, complete

source code means all the source code for all modules it contains, plus any associated interface denition les, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by oering access to copy from a designated place, then oering equivalent

access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is

intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of

any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may dier in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program species a version number of this License which applies to

it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are dierent, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

Appendix

English

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED

BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER

PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each source le to most eectively convey the exclusion of warranty; and each le should have at least the “copyright” line and a pointer to where the full notice is found.

One line to give the program’s name and a brief idea of what it does. Copyright (C) yyyy name of author This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as

published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software

Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type

`show w’. This is free software, and you are welcome to redistribute it under certain conditions; type `show c’ for details. The hypothetical commands `show w’ and `show c’ should show the appropriate parts of the General Public License. Of course, the

commands you use may be called something other than `show w’ and `show c’; they could even be mouse-clicks or menu items-

whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the

program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision’ (which makes passes at compilers) written by

James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this License.

GNU Lesser General Public License (LGPL)

Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

[This is the rst released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you rst think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.

Appendix

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object les to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we oer you this license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modied by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be aected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot eectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specied in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite dierent from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination ts its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modied version of the Library.

The precise terms and conditions for copying, distribution and modication follow. Pay close attention to the dierence between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”.

A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs

(which use some of those functions and data) to form executables.

The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based

on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modication”.)

“Source code” for a work means the preferred form of the work for making modications to it. For a library, complete source code

means all the source code for all modules it contains, plus any associated interface denition les, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modication are not covered by this License; they are outside its scope. The act of

running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.

1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.

Appendix

English

You may charge a fee for the physical act of transferring a copy, and you may at your option oer warranty protection in exchange

for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and

distribute such modications or work under the terms of Section 1 above, provided that you also meet all of these conditions:

a) The modied work must itself be a software library. b) You must cause the les modied to carry prominent notices stating that you changed the les and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. d) If a facility in the modied Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as

an argument passed when the facility is invoked, then you must make a good faith eort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-dened independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modied work as a whole. If identiable sections of that work are not derived from the Library,

and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to

exercise the right to control the distribution of derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a

volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To

do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all

subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a library.

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form

under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.

If distribution of object code is made by oering access to copy from a designated place, then oering equivalent access to copy

the source code from the same place satises the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or

linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because

it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.

When a “work that uses the Library” uses material from a header le that is part of the Library, the object code for the work may be

a derivative work of the Library even though the source code is not. Whether this is true is especially signicant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely dened by law.

If such an object le uses only numerical parameters, data structure layouts and accessors, and small macros and small inline

functions (ten lines or less in length), then the use of the object le is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6.

Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce

a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modication of the work for the customer’s own use and reverse engineering for debugging such modications.

You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered

by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:

a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in

the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modied executable containing the modied Library. (It is understood that the user who changes the contents of denitions les in the Library will not necessarily be able to recompile the application to use the modied denitions.)

b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already

present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modied version of the library, if the user installs one, as long as the modied version is interface-compatible with the version that the work was made with.

Appendix

c) Accompany the work with a written oer, valid for at least three years, to give the same user the materials specied in Subsection 6a, above, for a

charge no more than the cost of performing this distribution.

d) If distribution of the work is made by oering access to copy from a designated place, oer equivalent access to copy the above specied materials

from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.

For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for

reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally

accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:

a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be

distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to nd the

accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is

intended to apply, and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of

any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may dier in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library species a version number of this License which applies to

it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

Appendix

English

PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY

OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source le to most eectively convey the exclusion of warranty; and each le should have at least the “copyright” line and a pointer to where the full notice is found. one line to give the library’s name and an idea of what it does.> Copyright (C) year name of author

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as

published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software

Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob’ (a library for tweaking knobs) written by James Random Hacker.

signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice

Humax HD-5500T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual