HP HCPL-7101, HCPL-7100 Datasheet

1-402

High Speed CMOS Optocouplers

Technical Data

Features

• 1 µm CMOS IC Technology

• Compatibility with All +5 V CMOS and TTL Logic Families

• No External Components Required for Logic Interface

• High Speed: 15 MBd (HCPL-7100) and 50 MBd (HCPL-7101) Guaranteed

• Low Power Consumption

• Safety Approvals UL 1577 (3750 Vac/1 Min) VDE 0884 (V

IORM

= 848 V peak) CSA

• 3-State Output

• 3750 Vac/1 Minute Dielectric Withstand

• High Common Mode Transient Immunity

Applications

• Multiplexed Data Transmission

• Computer-Peripheral Interface

• Microprocessor System Interface

• Digital Isolation for A/D,

D/A Conversion

• Instrument Input/Output Isolation

• Motor Control

• Power Inverter

Description

The HCPL-7100/7101 optocoupler combines the latest CMOS IC technology, a new high-speed high-efficiency AlGaAs LED, and an optimized light coupling system to achieve outstanding performance with very low power consumption. It requires only two bypass capacitors for complete CMOS/TTL compatibility.

Basic building blocks of the HCPL-7100/7101 are a CMOS LED driver IC, an AlGaAs LED, and a CMOS detector IC. A CMOS or TTL logic input signal controls the LED driver IC which supplies current to the LED. The detector IC incorporates an integrated photodiode, a high-speed transimpedance amplifier and a voltage comparator with hysteresis. The 3-state output is CMOS and TTL

compatible and is controlled by the output enable pin, VOE.

The HCPL-7100/7101 consumes very little power, due to the CMOS IC technology and the light coupling system. The entire optocoupler typically uses only 10 mA of supply current, including the LED current.

World-wide safety approval and 3750 Vac/1 minute dielectric withstand is achieved with our patented “light-pipe” optocoupler packaging technology.

The HCPL-7100/7101 provides he user with an easy-to-use CMOS or TTL compatible optocoupler ideally suited for a variety of applications where high speed and low power consumption are desired.

HCPL-7100 HCPL-7101

Schematic

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

TRUTH TABLE

(POSITIVE LOGIC)

INPUT ENABLE OUTPUT

HH Z LH Z HL H LL L

5965-3578E

1-403

Ordering Information

HCPL-710x

0 = 15 MBd Minimum Data Rate 1 = 50 MBd Minimum Data Rate

Option yyy

300 = Gull Wing Surface Mount Lead Option 500 = Tape/Reel Package Option (1 k min.)

Option data sheets available. Contact your Hewlett-Packard sales representative or authorized distributor for information.

Package Outline Drawings

Standard DIP Package

9.40 (0.370)

9.90 (0.390)

1.78 (0.070) MAX.

1.19 (0.047) MAX.

HP XXXX



YYWW

DATE CODE

0.76 (0.030)

1.40 (0.055)

2.28 (0.090)

2.80 (0.110)

0.51 (0.020) MIN.

0.65 (0.025) MAX.

4.70 (0.185) MAX.

2.92 (0.115) MIN.

* PIN 3 IS THE ANODE OF THE INTERNAL LED AND MUST BE LEFT UNCONNECTED FOR GUARANTEED DATA SHEET PERFORMANCE.  DIMENSIONS IN MILLIMETERS AND (INCHES).

5678

4321

0.20 (0.008)

0.33 (0.013)

6.10 (0.240)

6.60 (0.260) 5° TYP.

7.36 (0.290)

7.88 (0.310)

GND1

DD1

GND2

DD2

PIN ONE

TYPE NUMBER

UL RECOGNITION

* PIN 3 IS THE ANODE OF THE INTERNAL LED AND

MUST BE LEFT UNCONNECTED FOR GUARANTEED DATA SHEET PERFORMANCE.

DIMENSIONS IN MILLIMETERS AND (INCHES).

1-404

*Refer to Option 300 data sheet for more information.

0.635 ± 0.25

(0.025 ± 0.010)

12° NOM.

0.20 (0.008)

0.33 (0.013)

9.65 ± 0.25

(0.380 ± 0.010)

0.51 ± 0.130

(0.020 ± 0.005)

7.62 ± 0.25

(0.300 ± 0.010)

9.65 ± 0.25

(0.380 ± 0.010)

6.350 ± 0.25

(0.250 ± 0.010)

1.02 (0.040)

1.19 (0.047)

1.19 (0.047)

1.78 (0.070)

9.65 ± 0.25

(0.380 ± 0.010)

4.83

(0.190)



TYP.

0.380 (0.015)

0.635 (0.025)

PIN LOCATION (FOR REFERENCE ONLY)

1.080 ± 0.320

(0.043 ± 0.013)

4.19

(0.165)

MAX.

1.780

(0.070)

MAX.

1.19

(0.047)

MAX.

2.540

(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES). TOLERANCES (UNLESS OTHERWISE SPECIFIED):  

xx.xx = 0.01 xx.xxx = 0.005 

HP XXXX



YYWW

DATE CODE

TYPE NUMBER

UL RECOGNITION

MOLDED

LEAD COPLANARITY  MAXIMUM: 0.102 (0.004)

Gull Wing Surface Mount Option 300*

Maximum Solder Reflow Thermal Profile

240

∆T = 115°C, 0.3°C/SEC

∆T = 100°C, 1.5°C/SEC

∆T = 145°C, 1°C/SEC

TIME – MINUTES

TEMPERATURE – °C

220 200 180 160 140 120 100

80 60 40 20

260

123456789101112

(NOTE: USE OF NON-CHLORINE ACTIVATED FLUXES IS RECOMMENDED.)

1-405

VDE 0884 (06.92) Insulation Characteristics

Description Symbol Characteristic Unit

Installation classification per DIN VDE 0110, Table 1

for rated mains voltage ≤ 300 V rms I-IV for rated mains voltage ≤ 600 V rms I-III

Climatic Classification 40/85/21 Pollution Degree (DIN VDE 0110, Table 1)* 2 Maximum Working Insulation Voltage V

IORM

848 V peak

Input to Output Test Voltage, Method b**

VPR = 1.875 x V

IORM

, Production test with tp = 1 sec, V

1591 V peak

Partial discharge < 5 pC

Input to Output Test Voltage, Method a**

VPR = 1.5 x V

IORM

, Type and sample test, tp = 60 sec, V

1273 V peak

Partial discharge < 5 pC

Highest Allowable Overvoltage** V

6000 V peak

(Transient Overvoltage, tTR = 10 sec) Safety-limiting values (Maximum values allowed in the event

of a failure, also see Figure 15)

Case Temperature T

175 °C

Input Power P

S,INPUT

80 mW

Output Power P

S,OUTPUT

250 mW

Insulation Resistance at TS, VIO = 500 V R

≥ 1 x 10

Ω

*This part may also be used in Pollution Degree 3 environments where the rated mains voltage is ≤ 300 V rms (per DIN VDE 0110). **Refer to the front of the optocoupler section in the current catalog for a more detailed description of VDE 0884 and other product safety requirements.

Insulation and Safety Related Specifications

Parameter Symbol Value Units Conditions

Min. External Air Gap L(IO1) 7.4 mm Measured from input terminals to output terminals, (External Clearance) shortest distance through air

Min. External Tracking L(IO2) 8.0 mm Measured from input terminals to output terminals, Path (External Creepage) shortest distance path along body

Min. Internal Plastic 0.5 mm Through insulation distance, conductor to conductor, Gap (Internal Clearance) usually the direct distance between the photoemitter

and photodetector inside the optocoupler cavity

Tracking Resistance CTI 175 V DIN IEC 112/VDE 0303 PART 1 (Comparative Tracking Index)

Isolation Group IIIa Material Group (DIN VDE 0110, 1/89, Table 1)

Option 300 – surface mount classification is Class A in accordance with CECC 00802.

Note: Optocouplers providing safe electrical separation per VDE 0884 do so only within the safety-limiting values to which they are qualified. Protective cut-out switches must be used to ensure that the safety limits are not exceeded.

VDE

Approved according to VDE 0884/06.92

Regulatory Information

The HCPL-7100/1 has been approved by the following organizations:

Recognized under UL 1577, Component Recognition Program, File E55361.

CSA

Approved under CSA Component Acceptance Notice #5, File CA

88324.

1-406

Parameter Symbol Min. Max. Unit

Storage Temperature T

-55 125 °C

Ambient Operating Temperature T

-40 85 °C

Supply Voltages V

DD1,2

0.0 5.5 V

Input Voltage V

-0.5 V

DD1

+ 0.5 V

Output Voltage V

-0.5 V

DD2

+ 0.5 V

Output Enable Voltage V

-0.5 V

DD2

+ 0.5 V

Average Output Current I

25 mA

Package Power Dissipation P

220 mW

Lead Solder Temperature T

260 °C

(1.6 mm Below Seating Plane, 10 sec.) Reflow Temperature Profile See Package Outline Drawings Section

Parameter Symbol Min. Max. Unit Test Conditions

Operating Temperature T

-40 85 °C

Supply Voltages V

DD1,2

4.5 5.5 V

Logic High Input Voltage V

2.0 V

DD1

Logic Low Input Voltage V

0.0 0.8 V

Logic High Output V

OEH

2.0 V

DD2

V Output in high impedance

Enable Voltage state Logic Low Output V

OEL

0.0 0.8 V Output enabled

Enable Voltage Input Signal Rise and tr, t

1ms

Fall Times TTL Fanout N 6 Standard Loads

Absolute Maximum Ratings

Recommended Operating Conditions

+ 9 hidden pages