HP HCPL-2730, HCPL-4701, HCPL-2731, HCPL-073A, HCPL-0731 Datasheet

...
Low Input Current, High Gain Optocouplers
Technical Data

6N139 6N138 HCPL-0701 HCPL-0700 HCNW139 HCNW138

Features
• High Current Transfer Ratio – 2000% Typical (4500% Typical for HCNW139/138)
• Low Input Current Requirements – 0.5 mA
• TTL Compatible Output –
0.1 V VOL Typical
• Performance Guaranteed over Temperature 0°C to 70°C
• Base Access Allows Gain Bandwidth Adjustment
• High Output Current – 60 mA
• Safety Approval
UL Recognized – 2500 V rms
for 1 Minute and 5000 V rms*
for 1 Minute per UL 1577 CSA Approved VDE 0884 Approved with
V
= 1414 V peak for
IORM
HCNW139 and HCNW138 BSI Certified (HCNW139 and
HCNW138)
• Available in 8-Pin DIP or SOIC-8 Footprint or Widebody Package
•MIL-STD-1772 Version Available (HCPL-5700/1)
Applications
• Ground Isolate Most Logic Families – TTL/TTL, CMOS/ TTL, CMOS/CMOS, LSTTL/ TTL, CMOS/LSTTL
• Low Input Current Line Receiver
• High Voltage Insulation (HCNW139/138)
• EIA RS-232C Line Receiver
• Telephone Ring Detector
• 117 V ac Line Voltage Status Indicator – Low Input Power Dissipation
• Low Power Systems – Ground Isolation

Functional Diagram

NC
ANODE
CATHODE
NC
1
2
3
4
8
V
CC
7
V
B
6
V
O
5
GND

Description

These high gain series couplers use a Light Emitting Diode and an integrated high gain photodetec­tor to provide extremely high current transfer ratio between input and output. Separate pins for the photodiode and output stage result in TTL compatible saturation voltages and high speed operation. Where desired the VCC and VO terminals may be tied together to achieve conven­tional photodarlington operation. A base access terminal allows a gain bandwidth adjustment to be made.
TRUTH TABLE
LED
ON
OFF
V
O
 LOW HIGH
*5000 V rms/1 minute rating is for HCNW139/138 and Option 020 (6N139/138) products only. A 0.1 µF bypass capacitor connected between pins 8 and 5 is recommended.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.
2
The 6N139, HCPL-0701, and CNW139 are for use in CMOS, LSTTL or other low power appli­cations. A 400% minimum current transfer ratio is guaranteed over 0 to 70°C operating range for only
0.5 mA of LED current.
(1 TTL Unit load ). A 300% minimum CTR enables operation with 1 TTL Load using a 2.2 k pull-up resistor.
Selection for lower input current down to 250 µA is available upon request.
The SOIC-8 does not require “through holes” in a PCB. This package occupies approximately one-third the footprint area of the standard dual-in-line package. The lead profile is designed to be compatible with standard surface
mount processes. The 6N138, HCPL-0700, and HCNW138 are designed for use mainly in TTL applications. Current Transfer Ratio (CTR) is 300% minimum over 0 to 70°C for an LED current of 1.6 mA
The HCPL-0701 and HCPL-0700 are surface mount devices packaged in an industry standard SOIC-8 footprint.
The HCNW139 and HCNW138
are packaged in a widebody
encapsulation that provides creep-
age and clearance dimensions
suitable for safety approval by
regulatory agencies worldwide.

Selection Guide

Widebody
8-Pin DIP Package Hermetic
(300 Mil) Small Outline SO-8 (400 mil) Single and
Dual Single Dual Minimum Absolute Dual
Single Channel Channel Channel Single Input ON Maxi- Channel Channel Package Package Package Channel Current Minimum mum Packages Package HCPL- HCPL- HCPL- Package (I
4731
[1]
[1]
[1]
0701 0731 HCNW139 0.5 mA 400% 18 V 0700 0730 HCNW138 1.6 mA 300% 7 V
070A
[1]
073A
[1]
6N139 2731
6N138 2730
HCPL-4701
[1]
) CTR V
F
40 µA 800% 18 V
0.5 mA 300% 20 V 5701
CC
HCPL-
[1] [1]
5700
[1]
5731
[1]
5730
Note:
1. Technical data are on separate HP publications.
3

Ordering Information

Specify Part Number followed by Option Number (if desired).
Example:
6N139#XXX
020 = 5000 V rms/1 Minute UL Rating Option* 300 = Gull Wing Surface Mount Option† 500 = Tape and Reel Packaging Option
Option data sheets available. Contact your Hewlett-Packard sales representative or authorized distributor for information.
*For 6N139 and 6N138 only. †Gull wing surface mount option applies to through hole parts only.

Schematic

ANODE
CATHODE
V
CC
8
I
CC
I
F
2 +
V
F
I
3
SHIELD
I
B
7
V
B
O
6
V
O
5
GND
Package Outline Drawings
8-Pin DIP Package (6N139/6N138)**
4
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
5° TYP.
TYPE NUMBER
1.19 (0.047) MAX.
1.080 ± 0.320
(0.043 ± 0.013)
**JEDEC Registered Data.
9.65 ± 0.25
(0.380 ± 0.010)
HP XXXXZ
YYWW
5678
OPTION CODE* DATE CODE
UR
UL RECOGNITION
4321
1.78 (0.070) MAX.
4.70 (0.185) MAX.
2.92 (0.115) MIN.
0.65 (0.025) MAX.
2.54 ± 0.25
(0.100 ± 0.010)
0.51 (0.020) MIN.
DIMENSIONS IN MILLIMETERS AND (INCHES). *MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020 OPTION NUMBERS 300 AND 500 NOT MARKED.
8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N139/6N138)
0.254
(0.010
+ 0.076
- 0.051
+ 0.003)
- 0.002)
1.19
(0.047)
MAX.
1.080 ± 0.320
(0.043 ± 0.013)
9.65 ± 0.25
(0.380 ± 0.010)
6
7
8
1
2
2.54
(0.100)
BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
5
6.350 ± 0.25
(0.250 ± 0.010)
3
4
1.780
(0.070)
MAX.
4.19
MAX.
(0.165)
0.635 ± 0.130
(0.025 ± 0.005)
PAD LOCATION (FOR REFERENCE ONLY)
1.016 (0.040)
1.194 (0.047)
4.826
TYP.
(0.190)
0.381 (0.015)
1.194 (0.047)
1.778 (0.070)
9.65 ± 0.25
(0.380 ± 0.010)
7.62 ± 0.25
(0.300 ± 0.010)
0.635 ± 0.25
(0.025 ± 0.010)
0.635 (0.025)
0.254
(0.010
12° NOM.
9.398 (0.370)
9.906 (0.390)
+ 0.076
- 0.051
+ 0.003)
- 0.002)
Small Outline SO-8 Package (HCPL-0701/HCPL-0700)
5
8765
3.937 ± 0.127
(0.155 ± 0.005)
PIN ONE
0.406 ± 0.076
(0.016 ± 0.003)
3.175 ± 0.127
(0.125 ± 0.005)
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
*
5.207 ± 0.254 (0.205 ± 0.010)  DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
XXX
YWW
*
5.080 ± 0.127
(0.200 ± 0.005)
(0.236 ± 0.008)
4321
1.270
(0.050)
(0.060)
5.994 ± 0.203
TYPE NUMBER (LAST 3 DIGITS)
DATE CODE
BSG
1.524
8-Pin Widebody DIP Package (HCNW139/HCNW138)
0 ~ 7°
0.305
(0.012)
45° X
0.203 ± 0.102
(0.008 ± 0.004)
MIN.
0.432
(0.017)
0.228 ± 0.025
(0.009 ± 0.001)
2.54 (0.100) TYP.
1.78 ± 0.15
(0.070 ± 0.006)
11.15 ± 0.15
(0.442 ± 0.006)
7
8
HP 
HCNWXXXX
YYWW
1
2
11.00
MAX.
(0.433)
6
5
TYPE NUMBER DATE CODE
3
4
1.55
(0.061)
MAX.
3.10 (0.122)
3.90 (0.154)
0.40 (0.016)
0.56 (0.022)
0.51 (0.021) MIN.
9.00 ± 0.15
(0.354 ± 0.006)
10.16 (0.400) TYP.
7° TYP.
5.10
MAX.
(0.201)
DIMENSIONS IN MILLIMETERS (INCHES).
0.254
(0.010
+ 0.076
- 0.0051 + 0.003)
- 0.002)
Loading...
+ 11 hidden pages