Hilti POS 150, POS 180 User Manual
POS 150/180
English
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05
English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used:
DANGER
DANGER !
▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING
WARNING !
▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.
CAUTION
CAUTION !
▶
Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage
to the equipment or other property.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use.
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household waste
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions
The numbering reflects the sequence of operations shown in the illustrations and may deviate
from the steps described in the text
Item reference numbers are used in the overview illustrations and refer to the numbers used in
the product overview section
This symbol is intended to draw special attention to certain points when handling the product.
Wireless data transfer
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05
2 English
1.3 Labels on the POS 150/180
The following labels are applied to the POS 150/180:
Laser radiation. Do not look straight into the laser beam. Laser class
3R.
1.4 Product information
products are designed for professional users and only trained, authorized personnel are permitted
to operate, service and maintain the products. This personnel must be specifically informed about the
possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by
untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
▶ Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Type: POS 150/180
Generation: 01
Serial no.:
1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration of conformity can be found at the end of this documentation.
The technical documentation is filed and stored here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistraße 6 | 86916 Kaufering, DE
2 Safety
2.1 General safety instructions, scanning tools
WARNING! Read all safety precautions and other instructions. Failure to observe the safety
instructions and other instructions can result in electric shock, fire and/or serious injury.
Keep all safety precautions and instructions for future reference.
Work area safety
▶ Keep your workplace clean and well lit. Cluttered or poorly lit workplaces invite accidents.
▶ Do not operate the product in explosive atmospheres, such as in the presence of flammable liquids,
gases or dust. Scanning tools create sparks which can ignite dust, fumes or vapors.
▶ Keep children and other persons clear when the product is in use. Distractions can cause you to
lose control of the product.
Electrical safety
▶ Do not expose the product to rain or moisture. Water entering the product will increase the risk of electric
shock.
Personal safety
▶ Stay alert, watch what you are doing and use common sense when operating a scanning tool. Do
not use a scanning tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating the scanning tool can result in serious personal injury.
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05
English 3
▶ Adopt the correct posture when working. Maintain proper footing and balance at all times. This
will allow you to control the scanning tool better, even in unexpected situations.
▶ Wear your personal protective equipment and always wear protective glasses. Depending on the
type of scanning tool you are using and its purpose, wearing safety equipment such as a dust mask,
slip-resistant safety shoes, a hard hat or hearing protection will reduce the risk of injury.
▶ Avoid starting the tool accidentally. Make sure that the scanning tool is switched off before
connecting it to the battery and before picking it up or carrying it. Carrying scanning tools with your
finger on the switch or plugging in scanning tools that are already switched on can cause accidents.
Using and handling the scanning tool
▶ Do not use a scanning tool if it has a faulty on/off switch. A scanning tool that can no longer be
switched on or off is dangerous and must be repaired.
▶ Store scanning tools out of reach of children when not in use. Do not allow persons who are not familiar
with the product or these instructions to operate it. Scanning tools are dangerous in the hands of
inexperienced persons.
▶ Scanning tools need care and attention. Check that moving parts operate satisfactorily and do not
jam, and make sure that no parts are broken or damaged in such a way that the scanning tool might no
longer function correctly. Have damaged parts repaired before using the scanning tool. Many accidents
are caused by poorly maintained scanning tools.
Using and handling the cordless power tool
▶ Use only the specified batteries in the scanning tools. Use of other batteries can result in injury and a
risk of fire.
▶ Recharge the batteries only with the chargers recommended by the manufacturer. A charger that is
suitable for a certain type of battery can be a fire hazard if used with other batteries.
▶ When the battery is not in use, keep it away from other metal objects such as paper clips, coins,
keys, nails, screws, or other small metal objects that could cause bridging between the terminals.
A short circuit between the battery terminals may cause burns or a fire.
▶ Liquid may leak from the battery if used incorrectly. Avoid contact with this liquid. Liquid leaking
from the battery may cause skin irritation or burns. If contact accidentally occurs, rinse with water. Seek
medical attention if the liquid comes into contact with the eyes.
2.2 Battery use and care
▶ Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion
batteries.
▶ Do not expose batteries to high temperatures, direct sunlight or fire.
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.
▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height
or show signs of damage. In this case, always contact your Hilti Service.
▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable
location, well away from flammable materials, where it can be kept under observation and allowed to
cool down. In this case, always contact your Hilti Service.
2.3 Safety instructions, total station
▶ Do not render safety devices ineffective and do not remove information and warning notices.
▶ If the product is opened improperly, laser radiation in excess of Class 2 may be emitted. Have the
product repaired by Hilti Service only.
▶ Check that the product functions correctly each time before use.
▶ Measurements taken through panes of glass or other objects may be inaccurate.
▶ The measurement may be incorrect if the conditions under which the measurement is taken change
rapidly, e.g. due to people walking through the path of the laser beam.
▶ Observe the informationprinted in the operating instructions concerning operation, care and maintenance.
▶ Do not use the product as a level.
▶ Do not point the product toward the sun or other powerful light sources.
▶ Although the product is designed for the tough conditions of construction site use, as with other
measuring instruments it should be treated with care.
▶ Check the accuracy of the product after it has been dropped or subjected to other mechanical stresses.
▶ Secure the site at which you are taking measurements and take care to avoid directing the laser beam
toward other persons or toward yourself.
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05
4 English
▶ When the product is brought into a warm environment from very cold conditions, or vice-versa, allow it
to become acclimatized before use.
▶ Keep the laser exit window clean in order to avoid measurement errors.
▶ Observe the accident prevention regulations applicable in your country.
▶ Use the product only within its specified limits.
▶ Precautions must be taken to ensure that the laser beam does not unintentionally strike highly reflective
surfaces.
▶ Precautions must be taken to ensure that persons do not stare directly into the beam.
▶ The laser beam must not be allowed to project beyond the controlled area.
▶ Switch the laser tool off when it is not in use.
▶ When switching distance measurement from prism measurement to reflectorless measurement, make
sure that you do not look at the objective lens of the tool.
▶ View the tool at an angle when setting it up with the aid of the circular bubble level.
▶ Laser beams should not be projected at eye height.
▶ The specified operating and storage temperatures must be observed.
2.4 Electromagnetic compatibility
Although the tool complies with the strict requirements of the applicable directives, Hilti cannot entirely rule
out the possibility of interference to the tool caused by powerful electromagnetic radiation, possibly leading
to incorrect operation. Check the accuracy of the tool by taking measurements by other means when working
under such conditions or if you are unsure. Likewise, Hilti cannot rule out the possibility of interference with
other devices (e.g. aircraft navigation equipment). The tool complies with the requirements of Class A; the
possibility of interference occurring in a domestic environment cannot be excluded.
Only for Korea: This laser range meter is suitable for commercial and industrial use and for the electromagnetic
radiation encountered in this field (Class A). Users must pay attention to this point and make sure that this
laser range meter is not used in a domestic environment.
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05
English 5
3 Description
3.1 Total station front
@
Grip
;
Focusing knob
=
Vertical drive
%
Horizontal drive
&
Tripod lock
(
Sight
)
Telescope with laser distancer
+
Lens
§
Guide light
/
Operator keyboard
:
Display
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05
6 English
3.2 Total station rear side
∙
Radio antenna
$
Battery compartment lock
£
Battery compartment
|
Circular bubble level
¡
Eyepiece
Q
Tripod screw
W
Laser plummet
3.3 POC 100
Key
@
Display
;
Control panel
=
Charging socket
%
USB socket (master)
&
USB socket (slave)
Printed: 24.04.2018 | Doc-Nr: PUB / 5153820 / 000 / 05
Loading...