Hikvision DS-K1T501SF Quick Start Guide

Video Access Control Terminal

Quick Start Guide

UD06874B-A

1

Appearance

78mm

Mic

LED

Indicator

Doorbell

Button

Front Left

Camera

218mm

Fingerprint

Scanner

and

Card Swiping

Area

Voice Talk

Button

45.5mm

Back

DIP Switch

12V Power

Serial Port

Alarm

Bottom

Network

Micro SIM Card Slot

Loud Speaker

Wiegand

Door Lock
and RS485

TF Card Slot

DIP Switch

No. Descripon

RS-485 Address

1 to 4

RS-485 Direcon

5

under Terminal Mode

Work Method

6

Wiegand Protocol in

7

Card Reader Mode

Matched Resistance

8

(available for RS-485
protocol)

The DIP switch from left to right is
from No.1 to No.8. If the switch’s
black part is on the upper side
means ON; while on the lower side
means OFF.
For Example, if the DIP switch is as
the picture shows on the left, the
binary value is 0000 1100, which
means the decimal value 12.

Sengs

ON: Refer to 1
OFF: Refer to 0

ON: Upstream
OFF: Down Stream

ON: Card Reader Mode;
OFF Terminal Mode

ON: Wiegand
Protocol of 26-bit
OFF: Wiegand
Protocol of 34-bit

ON: Enable
OFF: Disable

©2017 Hangzhou Hikvision Digital Technology Co., Ltd.

It includes instrucons on how to use the Product. The soware
embodied in the Product is governed by the user license agreement
covering that Product.

About this Manual

This Manual is subject to domesc and internaonal copyright protecon.

Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all

rights to this manual. This manual cannot be reproduced, changed,
translated, or distributed, parally or wholly, by any means, without the
prior wrien permission of Hikvision.

Trademarks

and other Hikvision marks are the property of Hikvision
and are registered trademarks or the subject of applicaons for the same
by Hikvision and/or its affiliates. Other trademarks menoned in this
manual are the properes of their respecve owners. No right of license is
given to use such trademarks without express permission.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE,
IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION
MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO
EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR
AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL,
INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR
LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT
TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF
REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN
ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW.
HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.

2

Installation

Before You Start:

Make sure that the device in the package is in good condition and all the assembly parts are included.
Make sure that the wall is strong enough to withstand three times the weight of the terminal.
Set the DIP address before installation.

Cable Hole

Plastic Sheet

Cable Hole

Plastic Sheet

1. Connect the cables with the connector on the rear
panel of the device.

2. Route the cables through the cable hole of the
mounting plate. The cable holes are on the right
side, left side and lower side of the rear cover.
If the right/left side cable hole is selected, remove
the plastic sheet of the cable hole.

3.Secure the mounting plate on
the wall with 4 supplied screws.

4.Connect the corresponding
cables.

5.Push the terminal in the
mounting plate from bottom up.

6.Tighten the screws on the
bottom of the terminal to fix the
terminal on the mounting plate
and complete the installation.

3

Wiring

Under the terminal mode, you can connect the RS-485 cables with RS-485 card reader or secure door control unit.

with RS-485 Card Reader with Secure Door Control Unit

4

Activation

Activating via the Web Client, the SADP tool, and the client software are supported.

Activating Device via Client Software

1. Click Device Management icon to enter the Device Management interface.

2. Select an inacve device from the device list. Click Acvate to pop up the Acvaon interface.

3. Create a password and confirm the new password. Click OK to start acvate.

4. Click “Edit Network” to configure the device IP address, mask address, gateway address, port No.

Online Devices (2)

Add to Client

IP

xx.xx.xx.xx

xx.xx.xx.xx

Regulatory Information

FCC Information

Please take aenon that changes or modificaon not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protecon against harmful interference in a residenal installaon. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may
cause harmful interference to radio communicaons. However, there is no guarantee that interference will
not occur in a parcular installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the radiator

and your body.

Add All Modify Netinfo

Device Type Firmware Version Server PortSecurity Device Serial No.

xxxxxxxxxxxxx xxxxxxxxxxxxx XX-XXXXXX

xxxxxxxxxxxxx xxxxxxxxxxxxx XX-XXXXXX8000Activate

Reset Password

Activate

8000Inactivate

RS-485 Card Reader

Refresh Every 60s

Filter

Secure Door
Control Unit

Activating Device via SADP Tool

1. Download SADP Soware: Get the SADP soware from the supplied
disk or the official website. Install and run the soware.

2. Acvate Device: Check the inacve device from the device list. Create a
password in the right side of the interface and confirm the password.

3. Edit Device IP Address: Check the device and manually edit the device
IP address, Port No., Subnet Mask, Gateway, etc.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operaon.

EU Conformity Statement

This product and - if applicable - the supplied accessories too
are marked with "CE" and comply therefore with the
applicable harmonized European standards listed under the RE
Direcve 2014/53/EU, the EMC Direcve 2014/30/EU, the
RoHS Direcve 2011/65/EU.

2012/19/EU (WEEE direcve): Products marked with this
symbol cannot be disposed of as unsorted municipal waste in
the European Union. For proper recycling, return this product
to your local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collecon points. For
more informaon see: www.recyclethis.info

2006/66/EC (baery direcve): This product
contains a baery that cannot be disposed of
as unsorted municipal waste in the European
Union. See the product documentaon for
specific baery informaon. The baery is
marked with this symbol, which may include
leering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the
baery to your supplier or to a designated
collecon point. For more informaon see:

www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operaon is
subject to the following two condions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operaon of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitaon est autorisée aux deux condions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est suscepble d'en compromere le fonconnement.
Under Industry Canada regulaons, this radio transmier may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmier by Industry
Canada. To reduce potenal radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communicaon.
Conformément à la réglementaon d'Industrie Canada, le présent émeeur radio peut
fonconner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émeeur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intenon des autres ulisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communicaon sasfaisante.
This equipment should be installed and operated with a minimum distance 20cm between

the radiator and your body.

Cet équipement doit être installé et ulisé à une distance minimale de 20 cm entre le
radiateur et votre corps.

Use only power
supplies listed in

the user

instrucons:

Model Manufacturer Standard

DSA-12PFT-12FUK 120100

DSA-12PFT-12FAU 120100

DSA-12PFT-12FIN 120100

DSA-12PFT-12FUS 120100

DSA-12PFT-12 FBZ 120100

Dee Van Enterprise Co., Ltd.

Dee Van Enterprise Co., Ltd.

Dee Van Enterprise Co., Ltd.

Dee Van Enterprise Co., Ltd.

Dee Van Enterprise Co., Ltd.

BS

AS

IS

IEC

NBR