Harman Kardon AVR-240 Service manual

Download

Page 1

harman/kardon

AVR240

7 X 50W 7.1 CHANNEL A/V RECEIVER

SERVICE MANUAL

ESD WAR N ING……………………………….2

LEAKAGE TESTING……………….…..…....3

BASIC SPECIFICATIONS…………………..4 PACKAGING………………………..………..5 FRO NT PANEL CO NTRO L S ………..…..…..6 REAR PANEL CONNECTIONS………….…9 REMOTE CONTROL FUNCTIONS.………12 CONNECTIONS………………………….…16 OPERATION………………………...………18 TROUBLESHOOTING GUIDE…...……..…24 PROCESSOR RESET……………….….…..24 DISASSEM BLY………………………………25

harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev 2 9/2006

CONTENTS

UNIT EXPLOD ED VI EW……………………..26 EXPLODED VIEW PARTS LIST……………27 AMP BIAS ADJUSTMENT………………….28 BULLETIN HK2006-01……………..……….29 TECH TIP HK2003-01…...….….………..…30 BLOCK DIAGRAM…………………………..31 ELECTRICAL PARTS LIST………………...32 PCB DRAWINGS……………………………71 SEMICONDUCTOR PINOUTS……….……77 SCHEMATICS………………………………148

WIRING DIAGRAM………….....................155

Page 2

AVR240 harman/kardon

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and

semiconductor "chip" components.

The following techniques should be used to help reduce the incidence of component damage caused by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on

your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to

prevent electrostatic charge build-up or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges

sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement

ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the

chassis or circuit assembly into which the device will be installed.

CAUTION :

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together

or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

Each precaution in this manual should be followed during servicing.

Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with

, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the

parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably

insulated from the supply circuit before retuming the product to the customer.

Page 3

SAFETY PRECAUTIONS

The following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECK

Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the AC power switch on. Any current measured must not exceed o.5mA.

ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.

AVR240 harman/kardon

Reading should not be above

0.5mA Device under test

Leakage current tester

Test all exposed metal surfaces

Also test with plug reversed (Using AC adapter plug as required)

Earth ground

AC Leakage Test

Page 4

The

Bridge

AVR240 harman/kardon

AVR 240 TECHNICAL SPECIFICATIONS

Audio Section

Stereo Mode Continuous Average Power (FTC)

65 Watts per channel, 20Hz–20kHz, @ <0.07% THD, both channels driven into 8 ohms

Six-Channel Surround Modes Power per Individual Channel

Front L&R channels: 50 Watts per channel @ <0.07% THD, 20Hz–20kHz into 8 ohms

Center channel: 50 Watts @ <0.07% THD, 20Hz–20kHz into 8 ohms

Surround (L & R Side, Back) channels: 50 Watts per channel @ <0.07% THD, 20Hz–20kHz into 8 ohms

Input Sensitivity/Impedance

Linear (High-Level) 200mV/47k ohms Signal-to-Noise Ratio (IHF-A) 100dB Surround System Adjacent Channel Separation

Pro Logic 40dB

Dolby Digital 55dB

DTS 55dB

Frequency Response

@ 1W (+0dB, –3dB) 10Hz –130kHz High Instantaneous

Current Capability (HCC) ±35 Amps Transient Intermodulation

Distortion (TIM) Unmeasurable Slew Rate 40V/µsec

FM Tuner Section

Frequency Range 87.5–108.0MHz

Usable Sensitivity IHF 1.3µV/13.2dBf

Signal-to-Noise Ratio Mono/Stereo 70/68dB

Distortion Mono/Stereo 0.2/0.3%

Stereo Separation 40dB @ 1kHz

Selectivity ±400kHz, 70dB

Image Rejection 80dB

IF Rejection 90dB

AM Tuner Section

Frequency Range 520–1720kHz Signal-to-Noise Ratio 45dB Usable Sensitivity Loop 500µV Distortion 1kHz, 50% Mod 0.8% Selectivity ±10kHz, 30dB

Video Section

Television Format NTSC Input Level/Impedance 1Vp-p/75 ohms Output Level/Impedance 1Vp-p/75 ohms

Video Frequency Response (Composite and S-Video) 10Hz–8MHz (–3dB)

Video Frequency Response (Component Video) 10Hz–50MHz (–3dB)

General

Power Requirement AC 120V/60Hz Power Consumption 65W idle, 540W maximum

(6 channels driven)

Dimensions (Product) (Shipping) Width 17.3 inches (440mm) 21.5 inches (545mm) Height 6.6 inches (168mm) 9.9 inches (251mm) Depth 15 inches (382mm) 17.9 inches (455mm)

(Product) (Shipping)

Weight 24.4 lb (11.1kg) 29.3 lb (13.3kg)

Depth measurement includes knobs, buttons and terminal connections. Height measurement includes feet and chassis. All features and specifications are subject to change without notice.

Harman Kardon, Harman International, Power for the Digital Revolution and Logic 7 are registered trademarks, and The Bridge and are trademarks, of Harman International Industries, Incorporated.

*Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol

are registered trademarks of Dolby Laboratories.

DTS, DTS Surround, DTS-ES, DTS 96/24 and DTS Neo:6 are registered trademarks of DTS, Inc.

VMAx is a registered trademark of Harman International Industries, Incorporated, and is an implementation of Cooper Bauck Transaural Stereo under patent license.

SACD is a trademark of Sony Electronics, Inc.

Apple and iPod are registered trademarks, and Shuffle is a trademark, of Apple Computer, Inc.

Please register your product on our Web site at www.harmankardon.com. Note: You’ll need the product’s serial number. At the same time you can choose to be notified about our new products and/or special promotions.

Page 5

Page 6

DIGITAL LOGIC 7

VID 1

DVD

FMAM

TAPE 6 8 CH

VID 2

VID 3

VID 4

PRO LOGIC

3 STEREO DSP

5 7 CH. STEREO

SURR. OFF



(

)!@

)

AVR 240

Optical 3

Coaxial 3

ideo 4

AVR240 harman/kardon

FRONT-PANEL CONTROLS

NOTE: To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

1 Main Power Switch 2 Power Indicator 3 Standby/On Switch 4 Headphone Jack 5 Tone Mode 6 Speaker Selector 7 Surround Mode Group Selector 8 Surround Mode Selector 9 Tuning Selector

‹/›

)

Buttons

1 Main Power Switch: Press this button to apply power to the AVR 240. When the switch is pressed in, the unit is in a Standby mode, as indicated by the amber

Power Indicator 2. This button MUST be

pressed in to operate the unit. To turn the unit off and prevent the use of the remote control, this switch should be pressed until it pops out from the front panel and the word “OFF” is seen at the top of the switch.

NOTE: This switch is normally left in the “ON” position.

2 Power Indicator: This LED lights amber when the unit is in the Standby mode to signal that the AVR is ready to be turned on. When the unit is in operation, the indicator is blue.

3 Standby/On Switch: When the Main Power

Switch

AVR 240; press it again to turn the unit off. The

Indicator

is “ON,” press this button to turn on the

turns blue when the unit is on.

Power

! Tuner Band Selector @ Set Button # Digital Input Selector $ Preset Station Selector % Delay Adjust Selector ^ Input Source Selector & Tuner Mode Selector * Optical 3 Digital Audio Input ( Coaxial 3 Digital Audio Input Ó Video 4 Video Input Jacks

4 Headphone Jack: This jack may be used to listen

to the AVR 240’s output through a pair of headphones. The speakers will automatically be turned off when the headphone jack is in use.When configuring your system using EzSet+, the calibration microphone should be plugged into this jack using the supplied adaptor that converts the small mini-plug at the end of the microphone’s cord to a 1/4" plug.

5 Tone Mode: This button controls the tone mode settings, enabling adjustment of the bass and treble boost/cut. You may also use it to take the tone controls out of the signal path completely for “flat” response.The first press of the button displays a TONE IN message in the Lower Display Line

ı and in the on-screen display. To take the controls

‹

›

‹

out of the signal path, press either of the

›

Buttons ) until the display reads TONE OUT.

To change the bass or treble settings, make sure that

TONE IN appears in the Lower Display Line ı

‹

›

‹

or press either of the

›

Buttons ) until it does.

Ô Video 4 Audio Input Jacks  Channel Adjust Selector Ò Volume Control Ú Input Indicators Û Speaker/Channel Input Indicators Ù Upper Display Line ı Lower Display Line ˆ Surround Mode Indicators ˜ Remote Sensor Window

Press the Tone Mode Button 5 until the desired option of

TREBLE MODE or BASS MODE

appears in the Lower Display Line ı and in the on-screen display and then press either of the Buttons ) to enter the desired boost or cut setting. Both treble and bass contours may be boosted or cut by up to + or –10dB in increments of 2dB. See pages 21 and 31 for more information on the tone controls.

NOTE: The AVR 240 is not equipped with a traditional Balance control. When listening to two-channel materials, if you wish to adjust the stereo image, you may use the

Channel Adjust Selector  to increase or

decrease the level of the left front channel by up to + or –10dB, and then to decrease or increase the right front channel by the corresponding amount. However, when listening to surround materials and most twochannel materials, it is recommended that you leave these settings at the results obtained during the configuration process described on pages 19 through 30.

‹

›

‹

›

FRONT-PANEL CONTROLS 55

Page 7

The

Bridge

AVR240 harman/kardon

FRONT-PANEL CONTROLS

6 Speaker Selector: Press this button to begin the process of configuring the unit to match the type of speakers used in your listening room. (See pages 26–28 for more information on speaker setup and configuration.)

7 Surround Mode Group Selector: Press this but- ton to select the top-level group of surround modes. Each press of the button will select the current or last used mode in each of the surround mode groups (e.g., Dolby, DTS, DTS Neo:6, Logic 7, DSP, Stereo). When the button is pressed so that the name of the surround mode group appears in the on-screen display and in the Surround Mode Selector 8 to cycle through the individual modes available. For example, press this button to select Dolby modes, and then press the Surround Mode Selector 8 to choose from the various Dolby mode options.

8 Surround Mode Selector: Press this button to select from among the available surround mode options for the mode group selected. The specific modes will vary based on the number of speakers available, the mode group and if the input source is digital or analog. For example, press the

Mode Group Selector

grouping such as Dolby or Logic 7, and then press this button to see the specific mode choices available. Note that the digital surround modes, such as Dolby Digital and DTS, may not be accessed unless that type of source signal is present, such as when a DVD movie or television signal programmed in Dolby Digital or DTS surround sound is playing. For more information on surround mode selection, see pages 23 and 32.

9 Tuning Selector: Press the left side of the button to tune lower-frequency stations and the right side of the button to tune higher-frequency stations. When the tuner is in the Manual mode, each tap will increase or decrease the frequency by one increment. When the tuner receives a strong enough signal for adequate reception, on-screen display and the When the tuner is the Auto mode, press the button once, and the tuner will scan for a station with acceptable signal strength. When the next station with a strong signal is tuned the scan will stop and the on-screen display and will indicate AUTO TUNED. When an FM Stereo station is tuned, the display will read AUTO ST TUNED.

To switch back and forth between the Auto and Manual tuning modes, press the

Selector

Lower Display Line ı, press the

Surround

7 to select a main mode

MANUAL TUNED will appear in the

Lower Display Line ı.

Lower Display Line ı

Tuner Mode

) ‹/› Buttons: When configuring the AVR 240’s

settings, use these buttons to select from the available choices

! Tuner Band Selector: Press this button to turn the AVR on and to select the Tuner as the input. Press it again to switch between the AM and FM frequency bands. (See page 37 for more information on the tuner.)

@ Set Button: When making choices during the setup and configuration process, press this button to enter the desired setting into the AVR 240’s memory.

# Digital Input Selector: Press this button to select one of the digital audio inputs or the analog audio input for any source. (See pages 32–37 for more information on digital audio.)

$ Preset Stations Selector: Press this button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 37 for more information on tuner presets.)

% Delay Adjust Selector: Press this button to begin the steps required to enter delay settings. (See pages 28–29 for more information on delay times.)

^ Input Source Selector: Press this button to change the input by scrolling up or down through the list of

Input Indicators Ú.

& Tuner Mode Selector: Press this button to select

Auto or Manual tuning.When the button is pressed so that the

AUTO appears in the Lower Display Line

ı, the tuner will search for the next station with an acceptable signal when the is pressed. When the button is pressed so that MANUAL appears in the Lower Display Line ı, each press of the increase the frequency.This button may also be used to switch between Stereo and Mono modes for FM radio reception. When weak reception is encountered, press the button so that

Display Line

switch to Mono reception. Press it again to switch back to Stereo mode. (See page 37 for more information on using the tuner.)

* Optical 3 Digital Audio Input: Connect the optical digital audio output of an audio or video product to this jack. When the input is not in use, the built-in shutter will close to avoid dust contamination that might degrade future performance.

( Coaxial 3 Digital Audio Input: This jack is used for connection to the output of portable audio devices, video game consoles or other products that have a coax digital audio jack.

ı and on the on-screen display to

Tuning Selector 9u

Tuning Selector 9u will

MANUAL appears in the Lower

Ó Video 4 Video Input Jacks: These jacks may be used for temporary connection to the composite or S-video output of video games, camcorders or other portable video products.You may make a connection to either jack at any time, but not to both simultaneously.

Ô Video 4 Audio Input Jacks: These audio jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players.

 Channel Adjust Selector: Press this button to begin the process of trimming the channel output levels using an external audio source. (For more information on output level trim adjustment, see page 38.)

Ò Volume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR 240 is muted, adjusting the Volume Control Òb will automatically release the unit from the silenced condition.

Ú Input Indicators: The current selected source will appear as one of these indicators.When the unit is turned on, the entire list of available modes will light briefly, and then revert to normal operation with only the active mode indicator illuminated.

NOTE: When /DMP has been selected as the input source, no

DMP/THE BRIDGE IS CONNECTED

will scroll across the Upper Display Line P, unless you have retitled the source name, in which case that name will appear. See page 20 for more information on input titling.

Û Speaker/Channel Input Indicators: These indi- cators are multipurpose, indicating both the speaker type selected for each channel and the incoming datasignal configuration. The left, center, right, right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is a single box. The center box lights when a “small” speaker is selected, and the two outer boxes light when “large” speakers are selected. When none of the boxes are lit for the center, surround or subwoofer channels, no speaker has been assigned that position. (See pages 26–28 for more information on configuring speakers.)

The letters inside each box display the active input channels. For standard analog sources, only the L and R will light, indicating a stereo input. For a digital source, the indicators will light to display the channels being received at the digital input. When the letters flash, the digital input has been interrupted. (See page 36 for more information on the Channel Indicators.)

Ù Upper Display Line: Depending on the unit’s sta- tus, a variety of messages will appear here. In normal

Input Indicator N will light.

6 FRONT-PANEL CONTROLS

Page 8

AVR240 harman/kardon

FRONT-PANEL CONTROLS

operation, this line will show current input source and which analog or digital input is in use.When the tuner is the input, this line will identify the station as AM or FM and show the frequency and preset number, if any.

ı Lower Display Line: Depending on the unit’s sta- tus, a variety of messages will appear here. In normal operation, the current surround mode will show here.

ˆ Surround Mode Indicators: The current selected surround mode will appear as one of these indicators. Note that when the unit is turned on, the entire list of available modes will light briefly, and then revert to normal operation with only the active mode indicator illuminated.

NOTE: When the Dolby Virtual Speaker or Dolby Headphone modes are in use, no

Indicator

name will scroll in the ˜ Remote Sensor Window: The sensor behind

this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it.

R will light. However, the surround mode

Lower Display Line Q.

Surround Mode

FRONT-PANEL CONTROLS 77

Page 9

The Bridge

•

∞

⁄

ﬁ

‹

™

‚

›

‡

ﬂ

The

Bridge

AVR240 harman/kardon

REAR-PANEL CONNECTIONS

NOTE: To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

¡ FM Antenna Jack ™ CD Audio Inputs £ Tape Outputs ¢ Tape Inputs ∞ Remote IR Input

§ Remote IR Output ¶ Preamp Outputs

• Subwoofer Output ª Front Speaker Outputs ‚ Surround Back Speaker Outputs ⁄ Surround Speaker Outputs ¤ Center Speaker Outputs ‹ Component Video Monitor Outputs › Component Video 1 Inputs

NOTE: To assist in making the correct connections for multichannel input, output and speaker connections, all connection jacks and terminals are colorcoded in conformance with the CEA standards as follows:

Front Left: White Front Right: Red

ﬁ Component Video 2 Inputs ﬂ AC Power Cord ‡ Switched AC Accessory Outlet ° Unswitched AC Accessory Outlet

· Optical Digital Audio Output a Coaxial Digital Audio Output b Coaxial Digital Audio Inputs c S-Video Monitor Output d DVD S-Video Input e DMP Connector f Video 1 S-Video Input g Optical Digital Audio Inputs h Video 1 S-Video Output i Video 2 S-Video Input

Center: Green Surround Left: Blue Surround Right: Gray Surround Back Left: Brown Surround Back Right: Tan Subwoofer: Purple Coaxial Digital Audio: Orange

j 6/8-Channel Direct Inputs k Video 2 S-Video Output

U Video 3 S-Video Input V Video Monitor Output W DVD Audio/Video Inputs X Video 1 Audio/Video Inputs Y Video 1 Audio/Video Outputs Z Video 2 Audio/Video Inputs a Video 2 Audio/Video Outputs b Video 3 Audio/Video Inputs c AM Antenna Terminals

Composite Video: Yellow Component Video “Y”: Green Component Video “Pr”: Red Component Video “Pb”: Blue

¡ FM Antenna Jack: Connect the supplied indoor (or an optional external) FM antenna to this terminal.

™ CD Audio Inputs: Connect these jacks to the analog audio outputs of a compact disc player or CD changer.

8 REAR-PANEL CONNECTIONS

Tape Outputs: Connect these jacks to the

RECORD/INPUT

¢ Tape Inputs: PLAY/OUT

jacks of an audio recorder.

Connect these jacks to the

∞ Remote IR Input: If the AVR 240’s front-panel IR sensor is blocked due to cabinet doors or other obstructions, an external IR sensor may be used. Connect the output of the sensor to this jack.

Page 10

The

Bridge

The

Bridge

AVR240 harman/kardon

REAR-PANEL CONNECTIONS

§ Remote IR Output: This connection permits the IR sensor in the receiver to serve other remote controlled devices. Connect this jack to the “IR IN” jack on Harman Kardon (or other compatible) equipment.

¶ Preamp Outputs: Connect these jacks to an optional, external power amplifier for applications where higher power is desired.

• Subwoofer Output: Connect this jack to the line- level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input.

ª Front Speaker Outputs: Connect these outputs to the matching + or – terminals on your left and right speakers.When making speaker connections always make certain to maintain correct polarity by connecting the color-coded (white for front left and red for front right) (+) terminals on the AVR 240 to the red (+) terminals on the speakers and the black (–) terminals on the AVR 240 to the black (–) terminals on the speakers. See page 15 for more information on speaker polarity.

‚ Surround Back Speaker Outputs: These speaker terminals are normally used to power the surround back speakers in a 7.1-channel system. Connect these outputs to the matching + and – terminals on your surround back channel speaker. In conformance with the CEA color-code specification, the brown terminal is the positive, or “+,” terminal that should be connected to the red (+) terminal on the left Surround Back speaker with older color-coding. The tan terminal is the positive, or “+”, terminal that should be connected to the red (+) terminal on the right Surround Back speaker with older color-coding. Connect the black (–) terminals on the AVR to the matching black negative (–) terminals on the surround back speakers. (See page 15 for more information on speaker polarity.)

⁄ Surround Speaker Outputs: Connect these out- puts to the matching + and – terminals on your surround channel speakers. In conformance with the CEA color-code specification, the blue terminal is the positive, or “+,” terminal that should be connected to the red (+) terminal on the Surround Left speaker with older color-coding, while the gray terminal should be connected to the red (+) terminal on the Surround Right speaker with the older color-coding. Connect the black (–) terminal on the AVR to the matching black negative (–) terminals for each surround speaker. (See page 15 for more information on speaker polarity.)

¤ Center Speaker Outputs: Connect these outputs to the matching + and – terminals on your center channel speaker. In conformance with the CEA color-code specification, the green terminal is the positive, or “+,” terminal that should be connected to

the red (+) terminal on speakers with the older colorcoding. Connect the black (–) terminal on the AVR to the black (–) terminal on your speaker. (See page 15 for more information on speaker polarity.)

‹ Component Video Monitor Outputs: Connect these outputs to the component video inputs of a video projector or monitor. When a source connected to one of the

Component Video Inputs ›ﬁ is

selected, the signal will be sent to these jacks. › Component Video 1 Inputs: Connect the

Y/Pr/Pb component video outputs of a DVD player, HDTV set-top converter, satellite receiver or other video source device with component video outputs to these jacks.

ﬁ Component Video 2 Inputs: Connect the

Y/Pr/Pb component video outputs of a DVD player, HDTV set-top converter, satellite receiver or other video source device with component video outputs to these jacks.

See page 20 for information on assigning the

Component Video 1 and 2 Inputs ›ﬁ to the appropriate source inputs.

ﬂ AC Power Cord: Connect the AC power cord to a non-switched AC wall outlet.

‡ Switched AC Accessory Outlet: These outlets may be used to power any device you wish to have turned on when the AVR 240 is turned on.

° Unswitched AC Accessory Outlet: This outlet may be used to power any AC device. The power will remain on at this outlet regardless of whether the AVR 240 is on or off.

NOTE: The total power consumption of all devices connected to the accessory outlets should not exceed 100 watts.

· Optical Digital Audio Output: Connect this jack

to the optical digital input connector on a CD-R/RW, MiniDisc or other digital recorder.

a Coaxial Digital Audio Output: Connect this jack

to the coaxial digital input of a CD-R/RW, MiniDisc or other digital recorder.

b Coaxial Digital Audio Inputs: Connect the coax digital output from a DVD player, HDTV receiver, player

or CD player to these jacks.The signal may be a

Dolby Digital signal, DTS signal or a standard PCM digital source.Do not connect the RF digital output of an LD player to these jacks.

c S-Video Monitor Output: If any of the input sources used in your system have S-video connections to the AVR, connect this jack to the S-video input on your television, projector or other video display.

d DVD S-Video Input: Connect the S-video output of a DVD player or other video source to this jack.

e Digital Media Player (DMP) Connector:

With the AVR 240 turned off, connect the optional Harman Kardon to this connector Digital Media Player source is selected,

. When the

you may view iPod control and navigation messages on your video display (if one is connected to one of the

Video Monitor Outputs cV), and in the Upper and Lower Display Lines PQ. You may navigate the iPod

and select tracks for playback using the

⁄

/¤/‹/

›

Buttons no, the Set Button p and Transport Controls ` on your AVR remote. See page 37 for

more information.

f Video 1 S-Video Input: If the product connected to the

Video 1 Audio Inputs X has S-video capability,

connect this jack to the PLAY/OUT S-video jack on that unit and then make certain that the

Monitor Output

c is connected as described above.

S-Video

g Optical Digital Audio Inputs: Connect the optical digital output from a DVD player, HDTV receiver,LD player or CD

player to these jacks.The signal may be a Dolby Digital signal, a DTS signal or a standard PCM digital source.

h Video 1 S-Video Output: If the product connected to the

Video 1 Audio/Video Outputs Y has S-video

capability, connect this jack to the REC/IN S-video jack on that unit.

i Video 2 S-Video Input: If the product connected to the

Video 2 Audio/Video Inputs Z has S-video

capability, connect this jack to the PLAY/OUT S-video jack on that unit and then make certain that the S-Video Monitor Output c is connected as described above.

j 6/8-Channel Direct Inputs: These jacks are used for connection to source devices such as DVDAudio or SACD

™

players with discrete analog outputs. Depending on the source device in use, all eight jacks may be used, though in many cases only connections to the front left/right, center, surround left/right and LFE (subwoofer input) jacks will be used for standard

5.1 audio signals.

k Video 2 S-Video Output: If the product connected to the

Video 2 Audio Outputs a has S-video capa-

bility, connect this jack to the REC/IN S-video jack on that unit.

U Video 3 S-Video Input: If the product connected to the

Video 3 Audio Inputs b has S-video capability,

connect this jack to the PLAY/OUT S-video jack on that unit and then make certain that the

Monitor Output

c is connected as described above.

S-Video

REAR-PANEL CONNECTIONS 9

Page 11

AVR240 harman/kardon

REAR-PANEL CONNECTIONSREAR-PANEL CONNECTIONS

V Video Monitor Output: Connect this jack to the composite video input of a TV monitor or video projector to view the on-screen menus and the output of a standard video source.

W DVD Audio/Video Inputs: Connect the composite video and L/R analog audio outputs of a DVD player or other video source to these jacks.

X Video 1 Audio/Video Inputs: Connect the com- posite video and L/R analog audio PLAY/OUT jacks of a VCR or other video source to these jacks.

Y Video 1 Audio/Video Outputs: Connect the composite video and L/R analog audio REC/IN jacks of a VCR or other video recording device such as a DVD recorder or PVR to these jacks.

Z Video 2 Audio/Video Inputs: Connect the com- posite video and L/R analog audio PLAY/OUT jacks of a cable television box or other video source to these jacks.

a Video 2 Audio/Video Outputs: Connect the composite video and L/R analog audio REC/IN jacks of a VCR or other video recording device such as a DVD recorder or PVR to these jacks.

b Video 3 Audio/Video Inputs: Connect the com- posite video and L/R analog audio PLAY/OUT jacks of an HDTV tuner or other video source to these jacks.

c AM Antenna Terminals: Connect the AM loop antenna supplied with the receiver to these terminals. If an external AM antenna is used, make connections to the

AM and GND terminals in accordance with

the instructions supplied with the antenna.

NOTE ON VIDEO CONNECTIONS: When connecting a video source product such as a VCR, DVD player, satellite receiver, cable set-top box, personal video recorder or video game to the AVR 240, you may use either a composite or S-video connection, but not both.

10 REAR-PANEL CONNECTIONS

Page 12

The

Bridge

POWER

MUTE

AVR

DVD

M/FM

TAPE

VID 2

VCR

CBL/SAT

6/8 CH

DMP

VID 1

VID 3

VID4

SLEEP

SURR.

CH.

VOL.

SET

TUN-M

MEM

D.SKIP

DIRECT

OSD

TUNING

DOLBY SUR

DTS SUR

DTS NEO:6

STEREO

LOGIC 7

SKIP

DOWN

PRESET

CLEAR

EST

NIGHT

DIM

The

Bridge

AVR240 harman/kardon

REMOTE CONTROL FUNCTIONS

a Power Off Button b IR Transmitter Window c Program Indicator d Power On Button e Input Selectors f AVR Selector g AM/FM Tuner Select h Dim Button i Test Button j Sleep Button k DSP Surround Mode Selector l Night Mode m Channel Select Button n

⁄/¤

Buttons

‹/›

Buttons

p Set Button q Digital Select r Numeric Keys s Tuner Mode t Direct Button u Tuning Up/Down v OSD Button w Dolby Mode Selector x DTS Digital Mode Selector y Logic 7 Mode Select Button z Skip Up/Down Buttons ` Transport Controls

R Stereo Mode Select Button S DTS Neo:6 Mode Select T U V W X Y Z a b c d e f

Macro Buttons Disc Skip Button Preset Up/Down Clear Button Memory Button Delay/Prev. Ch. Speaker Select Spare Button Volume Up/Down TV/Video Selector DMP Selector 6-Channel/8-Channel Direct Input Mute

NOTES:

• The function names shown here are each button’s feature when used with the AVR 240. Most buttons have additional functions when used with other devices. See pages 44–45 for a list of these functions.

• To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

REMOTE CONTROL FUNCTIONS 11

Page 13



AVR240 harman/kardon

REMOTE CONTROL FUNCTIONS

IMPORTANT NOTE: The AVR 240’s remote may be programmed to control up to seven devices, including

the AVR 240. Before using the remote, it is

important to

Button

remember to press the Input Selector

e that corresponds to the unit you wish to operate. In addition, the AVR 240’s remote is shipped from the factory to operate the AVR 240 and most Harman Kardon CD or DVD players and cassette decks.The remote is also capable of operating a wide variety of other products using the control codes that are part of the remote. Before using the remote with other products, follow the instructions on page 41 to program the proper codes for the products in your system.

It is also important to remember that many of the buttons on the remote take on different functions, depending on the product selected using the Device Control Selectors.The descriptions shown here primarily detail the functions of the remote when it is used to operate the AVR 240. (See pages 42–45 for information about alternate functions for the remote’s buttons.)

a Power Off Button: Press this button to place the AVR 240 or a selected device in the Standby mode.

b IR Transmitter Window: Point this window towards the AVR 240 when pressing buttons on the remote to make certain that infrared commands are properly received.

c Program Indicator: This three-color indicator is used to guide you through the process of programming the remote. (See page 41 for information on programming the remote.)

d Power On Button: Press this button to turn on the power to a device selected by pressing one of the

Input Selectors e.

e Input Selectors: Pressing one of these buttons

will perform three actions at the same time. First, if the AVR 240 is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the AVR 240. Finally, it will change the remote control so that it controls the device selected. After pressing one of these buttons you must press the

AVR Selector Button f again to operate the

AVR 240’s functions with the remote.

f AVR Selector: Pressing this button will switch the remote so that it will operate the AVR 240’s functions. If the AVR 240 is in the Standby mode, it will also turn the AVR 240 on.

g AM/FM Tuner Select: Press this button to select the AVR 240’s tuner as the listening choice. Pressing this button when the tuner is already in use will select between the AM and FM bands.

h Dim Button: Press this button to activate the Dimmer function, which reduces the brightness of the front panel display, or turns it off entirely. The first press of the button shows the default state, which is full brightness by indicating

Display Line

VFD FULL in the Lower

ı. Press the button again within five

seconds to reduce the brightness by 50%, as indicated by

VFD HALF showing in the Lower Display Line

ı. Press the button again within five seconds and the

main display will go completely dark. Note that this setting is temporary, in that regardless of any changes, the display will always return to full brightness when the AVR is turned on. In addition, the

Power Indicator 2 will

always remain at full brightness regardless of the setting. This is to remind you that the AVR is still turned on.

i Test Button: Press this button to begin the sequence used to calibrate the AVR 240’s output levels. (See pages 25, 29 and 38 for more information on calibrating the AVR 240.)

j Sleep Button: Press this button to place the unit in the Sleep mode.After the time shown in the display, the AVR 240 will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order:

See page 31 for more information on the Sleep Function. This button is also used to change channels on your TV when the TV is selected.

k DSP Surround Mode Selector: Press this but- ton to cycle through the DSP, VMAx and Stereo surround modes such as Hall, Theater,VMAx Near and Far, and Surround Off. This button is also used to tune channels when the TV is selected using the device

Input Selector e.

l Night Mode: Press this button to activate the

Night mode.This mode is available in specially encoded digital sources, and it preserves dialogue (center channel) intelligibility at low volume levels.

m Channel Select Button: This button is used to start the process of setting the AVR 240’s output levels to an external source. Once this button is pressed, use the

⁄/¤

Buttons n

then press the Set Button p, followed by the Buttons

n again, to change the level setting. (See

to select the channel being adjusted,

⁄/¤

pages 29 and 38 for more information.) However, Harman Kardon recommends that you first perform the EzSet+ procedure, as described on pages 23 to 25.

⁄/¤

Buttons: These multipurpose buttons are

used to change or scroll through items in the onscreen menus, make configuration settings such as digital inputs or delay timing, or to select surround modes.When changing a setting, first press the button for the function or setting to be changed (e.g., press the

DSP Surround Mode Selector k to select a

sound field mode or the

Digital Select Button q

to change a digital input) and then press one of these buttons to scroll through the list of options or to increase or decrease a setting. The sections in this manual describing the individual features and functions contain specific information on using these buttons for each application.

‹/›

Buttons: These buttons are used to change

the menu selection or setting during some of the setup procedures for the AVR 240.

p Set Button: This button is used to enter settings into the AVR 240’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment.

q Digital Select: Press this button to assign one of the digital inputs

*(bg to a source. (See pages 20 and 35 for more information on using digital inputs.)

r Numeric Keys: These buttons serve as a 10- button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, Cable or SAT has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.

I Tuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so that MANUAL appears in the Lower Display Line ı, pressing the

Tuning Buttons 9u will move the

frequency up or down in single-step increments. When the FM band is in use, pressing this button when a station’s signal is weak will change to monaural reception. (See page 37 for more information.)

J Direct Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button, simply press the proper

Numeric Keys r to select a sta-

tion. (See page 37 for more information on the tuner.)

12 REMOTE CONTROL FUNCTIONS

Page 14

The

Bridge

The

Bridge

AVR240 harman/kardon

REMOTE CONTROL FUNCTIONS

u Tuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the been pressed so that screen display and

Tuner Mode Button s& has

AUTO appears in the on-

Lower Display Line ı, pressing

and holding either of the buttons for three seconds will cause the tuner to seek the next station with acceptable signal strength for quality reception. When

MANUAL

appears in the Lower Display Line ı, pressing these buttons will tune stations in single-step increments. (See page 37 for more information.)

v OSD Button: Press this button to activate the On-Screen Display (OSD) system used to set up or adjust the AVR 240’s parameters.

w Dolby Mode Selector: This button is used to select from among the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II or IIx, or Dolby Virtual Speaker modes or Dolby 3 Stereo.When a Dolby Digital-encoded source is in use, the Dolby Digital mode may also be selected. When the headphones are in use, this button selects from among the Dolby Headphone modes. (See pages 33–34 for the available Dolby surround mode options.)

x DTS Digital Mode Selector: When a DTS- encoded digital source is selected, each press of this button will scroll through the available DTS modes.The specific choice of modes will vary according to whether or not the source material contains DTS-ES 6.1 Discrete encoding. When a DTS source is not in use, this button has no function. (See page 33 for the available DTS digital options.)

y Logic 7 Mode Select Button: Press this button to select from among the available Logic 7 surround modes. (See page 33 for the available Logic 7 options.)

z Skip Up/Down Buttons: These buttons do not have a direct function with the AVR 240, but when used with a compatibly programmed CD or DVD changer they will change to the previous disc in the changer or carousel.

` Transport Controls: These buttons do not have any functions for the AVR 240, but they may be programmed for the forward/reverse play operation of a wide variety of CD or DVD players, and audio or video cassette recorders.When the DMP source is in use, these buttons may be used to operate some functions on a compatible iPod

if it is docked in The Bridge. See page 37 for more information on using .

When the remote is used to control the AVR, or the VID2 or VID3 device, by default these buttons are programmed to operate the DVD player. However, you may use the Transport Control Punch-Through feature described on page 43 to program these buttons to operate another device’s transport controls when the AVR, VID2 or VID3 has been selected.

R Stereo Mode Select Button: When the button is pressed so that the

Lower Display Line ı, with only the Surr Off

Surround Mode Indicator

SURROUND OFF appears in

ˆ lit, the AVR will operate in a bypass mode with true, fully analog, two-channel left/right stereo mode with no surround processing or bass management, unlike other modes where digital processing is used. When the button is pressed so that

SURROUND OFF appears in the Lower Display Line Surround Mode Indicators

ı, with both the DSP and Surr Off

ˆ lit, you may enjoy a

two-channel presentation of the sound along with the benefits of bass management. Depending on whether your system is configured for 5.1 or 6.1/7.1 channels, the next press of the button will cause either 5 CH STEREO or 7 CH STEREO to appear, and the stereo signal will be routed to all five (or seven) speaker channels. (See page 34 for more information on stereo playback modes.)

S DTS Neo:6 Mode Select: Press this button to

select a DTS Neo:6 mode.These modes take a twochannel stereo- or matrix surround-encoded source and create a full five-, six- or seven-channel sound field. (See page 33 for the DTS Neo:6 options.)

T Macro Buttons: Press these buttons to store or recall a “Macro”, which is a preprogrammed sequence

of commands stored in the remote. (See page 41 for more information on storing and recalling macros.)

U Disc Skip Button: This button has no direct function for the AVR 240 but is most often used to change to the next disc in a CD or DVD player when the remote is programmed for that type of device. (See page 42 for more information on using the remote with products other than the AVR 240.)

V Preset Up/Down: When the tuner is in use,

press these buttons to scroll through the stations programmed into the AVR 240’s memory. When some source devices, such as CD players,VCRs and

cassette decks, are selected using the device

Selectors

e, these buttons may function as

Input

Chapter Step or Track Advance. W Clear Button: Press this button to clear incorrect

entries when using the remote to directly enter a radio station’s frequency.

X Memory Button: Press this button to enter a radio station into the AVR 240’s preset memory. First, tune the desired station, and then press this button. Two underline indicators will flash at the right side of the Upper Display Line P, and within five seconds press the

Numeric Keys r for the preset number

between 01 and 30 that you wish to assign to the station. (See page 37 for more information.)

Y Delay/Prev Ch.: Press this button to begin the process for setting the delay times used by the AVR 240 when processing surround sound. After pressing this button, the delay times are entered by pressing the

⁄/¤

Set Button p and then using the

Buttons n to change the setting. Press the

Set Button p again to complete the process.

(See page 22 for more information.) However, Harman Kardon recommends that you first perform the EzSet+ procedure, as described on pages 23–25.

Z Speaker Select: Press this button to begin the process of configuring the AVR 240’s bass management system for use with the type of speakers used in your system. Once the button has been pressed, use the channel you wish to set up. Press the

⁄/¤

Buttons n to select the

Set Button

p and then select another channel to configure. When all adjustments have been completed, press the

Set Button p twice to exit the settings and

return to normal operation. (See page 26 for more information.) However, Harman Kardon recommends that you first perform the EzSet+ procedure, as described on pages 23–25.

a Spare Button: This button has no direct function for the AVR 240, but may be used by other devices.

b Volume Up/Down: Press these buttons to raise or lower the system volume. By default, the

Up/Down Buttons

b are programmed at the fac-

Volume

tory to control the AVR 240’s volume, no matter which source device has been selected (except TAPE). You may reprogram these buttons to control the volume of another device, such as your TV, using the Volume Control Punch-Through instructions found on page 43.

c TV/Video Selector: This button does not have a direct function on the AVR 240, but when used with a compatible VCR, DVD or satellite receiver, pressing this button will switch between the output of the device and the external video input. Consult the owner’s manual for your specific player or receiver for the details of how it implements this function.

REMOTE CONTROL FUNCTIONS 13

Page 15

The

Bridge

The

Bridge

The

Bridge

The

Bridge

AVR240 harman/kardon

REMOTE CONTROL FUNCTIONS

d Digital Media Player (DMP)

Selector:

When Harman Kardon’s (optional) is connected to

Connector

Digital Media Player (DMP)

e and a compatible Apple®iPod®is docked in , pressing this selector will select the iPod as the audio source input device for the AVR 240. In addition, if a video display is connected to one of the

Video Monitor Outputs cV, the

iPod’s messages will appear on screen, and in the Upper and Lower Display Lines PQ. The

⁄/¤

/‹/

› Buttons no, the Set Button

p and the Transport Controls ` may be used

to navigate the iPod and to operate many functions. See page 37, and the manuals for The Bridge and your iPod for more information.

6-Channel/8-Channel Direct Input: Press

this button to select the device connected to the 6/8-Channel Direct Inputs j.

(See page 31 for

more information.) When the device connected to the 6/8-Channel Direct Input j is also a video source, such as a DVD or DVD-Audio player with an onboard audio decoder, you must first select that video source by pressing one of the

Input Selectors e, then

press this button to choose the device connected to the

6/8-Channel Direct Input j as the audio

source. Note that if you desire, you may select any video source to be used in conjunction with the

Channel Direct Input

j as the audio source.

6/8-

f Mute: Press this button to momentarily silence the AVR 240 or TV set being controlled, depending on which device has been selected. When the AVR 240 remote is being programmed to operate another device, this button is pressed with the

Input Selector Button

e to begin the programming process. (See page 41 for more information on programming the remote.)

14 REMOTE CONTROL FUNCTIONS

Page 16

The

Bridge

The

Bridge

The

Bridge

AVR240 harman/kardon

INSTALLATION AND CONNECTIONS

System Installation

After unpacking the unit, locating it in a place with adequate ventilation and placing it on a solid surface capable of supporting its weight, you will need to make the connections to your audio and video equipment.

IMPORTANT NOTE: For your personal safety and to avoid possible damage to your equipment and speakers, it is always a good practice to turn off and unplug the AVR and ALL source equipment from the AC output before making any audio or video system connections.

Audio Equipment Connections

We recommend that you use high-quality interconnect cables when making connections to source equipment and recorders to preserve the integrity of the signals.

1. Connect the analog outputs of a CD player to the

CD Audio Inputs ™.

NOTE: When the CD player has both fixed and vari-

able audio outputs, it is best to use the fixed output unless you find that the input to the receiver is so low that the sound is noisy, or so high that it is distorted.

2. Connect the analog Play/Out jacks of a cassette deck, MD, CD-R or other audio recorder to the Tape Input Jacks ¢. Connect the analog Record/In jacks on the recorder to the

Output Jacks

£ on the AVR 240.

3. Connect the output of any digital sources such as

a CD or DVD changer or player, advanced video game, a digital satellite receiver, HDTV tuner or digital cable set-top box or the output of a compatible computer sound card to the Coaxial Digital Audio Inputs bg*(.We recommend connecting the coaxial digital audio output of your DVD player to the

Audio Input

·, since that digital input is assigned to the DVD source by default. The Video 2/Cable/Sat source defaults to the

Digital Audio Input

g. If your cable television set-top box or satellite receiver is equipped with an optical digital audio output, we recommend that you connect it to this input to obtain the benefits of higher-quality digital audio (such as PCM, Dolby Digital 2.0 or Dolby Digital 5.1 signals when broadcast by your cable or satellite provider).

4. Connect the

Outputs

Coaxial or Optical Digital Audio

·a on the rear panel of the AVR 240 to the matching digital input connections on a CD-R or MiniDisc or other digital recorder.

5. Assemble the AM Loop Antenna supplied with the unit so that the tabs at the bottom of the antenna loop snap into the holes in the base. Connect it to the

AM Antenna Terminals c.

Tape

Optical and

Coax 1 Digital

Optical 1

6. Connect the supplied FM antenna to the ohm)

Connection ¡. The FM antenna may be an

FM (75-

external roof antenna, an inside powered or wirelead antenna or a connection from a cable TV system. If the antenna or connection uses 300-ohm twin-lead cable, you must use the 300-ohm-to-75ohm adaptor supplied with the unit to make the connection.

7. With the AVR 240 turned off, connect the optional Harman Kardon to

Player (DMP) Connector

iPod

may be docked in when you wish to

Digital Media

e. Your compatible

use it as an audio source device.Video materials stored on the iPod may not be viewed when The Bridge is in use.

8. Connect the front, center, surround and surround back speaker outputs

ª‚⁄¤ to the respec-

tive speakers.

To ensure that all the audio signals are carried to your speakers without loss of clarity or resolution, we suggest that you use high-quality speaker cable. Many brands of cable are available and the choice of cable may be influenced by the distance between your

speakers and the receiver, the type of speakers you use, personal preferences and other factors. Your dealer or installer is a valuable resource to consult in selecting the proper cable.

Regardless of the brand of cable selected, we recommend that you use a cable constructed of copper with a gauge of 14 or smaller.

multistrand

Remember that in specifying cable, the lower the number, the thicker the cable.

Cable with a gauge of 16 may be used for short runs of less than 10 feet. We do not recommend that you use cables with an AWG equivalent of 18 or higher, due to the power loss and degradation in performance that will occur.

Cables that are run inside walls should have the appropriate markings to indicate listing with UL, CSA or other appropriate testing agency standards. Questions about running cables inside walls should be referred to your installer or a licensed electrician who is familiar with the NEC and/or the applicable local building codes in your area.

When connecting wires to the speakers, observe proper polarity. Note that the positive (+) terminal of each speaker connection may carry a specific color

code, as noted on page 8. However, many speakers still use a red terminal for the positive (+) connection. Connect the “negative” or “black” wire to the same terminal on both the receiver and the speaker.

NOTE: While most speaker manufacturers adhere to an industry convention of using black terminals for negative and red ones for positive, some may vary from this configuration. To ensure proper phase and optimal performance, consult the identification plate on your speaker or the speaker’s manual to verify polarity. If you do not know the polarity of your speaker, ask your dealer for advice before proceeding, or consult the speaker’s manufacturer.

We also recommend that the length of cable used to connect speaker pairs be identical. For example, use the same length piece of cable to connect the front-left and front-right or surround-left and surround-right speakers, even if the speakers are a different distance from the AVR 240.

9. Connections to a subwoofer are normally made via a line-level audio connection from the Subwoofer Output • to the line-level input of a subwoofer with a built-in amplifier. When a passive subwoofer is used, the connection first goes to a power amplifier, which will be connected to one or more subwoofers. If you are using a powered subwoofer that does not have line-level input connections, follow the instructions furnished with the speaker for connection information.

10. If an external multichannel audio source with 5.1,

6.1 or 7.1 outputs such as an external digital processor/decoder, DVD-Audio or SACD player is used, connect the outputs of that device to the

6/8-Channel Direct Inputs j.

Video Equipment Connections

Video equipment is connected in the same manner as audio components.The use of high-quality interconnect cables is recommended to preserve signal quality.

1. Connect a VCR’s, DVD recorder’s, personal video recorder’s or other video source’s audio and video Play/Out jacks to the

Video 1 Audio/Video and/or

S-Video Input Jacks OX on the rear panel. The

Audio and Video Record/In jacks on the recorder should be connected to the

Video 1 Audio/Video

and/or S-Video Output Jacks QY on the AVR 240. Although any video device may be connected to these jacks, we recommend connecting your video recorder so that you may take advantage of the fact that the remote control is preprogrammed with video recorder product codes for the Video 1 device.

2. Connect the analog audio and video outputs of a satellite receiver, cable TV converter, television set

INSTALLATION AND CONNECTIONS 15

Page 17

AVR240 harman/kardon

INSTALLATION AND CONNECTIONS

or any other video source to the Video 2 Audio/Video and S-Video Input Jacks

Although any video device may be connected to these jacks, we recommend connecting your cable TV converter or satellite receiver so that you may take advantage of the fact that the remote control is preprogrammed with the product codes of these device types for the Video 2 device.

3. Connect the analog audio and video outputs of a television or other video device to the

Audio

and Video Input Jacks Ub on the rear

panel. Although any video or audio device may be connected to these jacks, we recommend connecting your television so that you may take advantage of the fact that the remote control is preprogrammed with TV product codes for the Video 3 device. Important: If you are only using the television as a display device (i.e., if you receive your television programs through a cable box or satellite receiver), do not connect the television’s outputs to the

3 Audio

and Video Input Jacks Ub, or to any

other inputs on the AVR 240.

4. Connect the analog audio and video outputs of a DVD or laser disc player to the

and S-Video Inputs

5. Connect the digital audio outputs of a DVD player, satellite receiver, cable box or HDTV converter to the appropriate bg*(. Remember that the DVD source defaults to the the Video 2/Cable/Sat source defaults to the Optical 1 Digital Audio Input g. All other sources default to their analog inputs, although any source may be assigned to any digital audio input on the receiver.

6. Connect the

Output

cV jacks on the receiver to the compos- ite or S-video input of your television monitor or video projector.

7. If both your video display monitor and at least one video source device, such as a DVD player or HDTV set-top box, is equipped with component video capability, then you may connect the component video outputs of the device to one of the two Component Video Inputs ›ﬁ.

It is recommended that you connect a DVD player or a digital recorder to the ›, as this input is assigned to the DVD, CD, Tuner and Tape sources by default. Thus, whenever any of these sources is selected, you may view the component video output of the device connected to the Component Video 1 Inputs ›, enabling you to view and listen to different sources.

dW.

Optical or Coaxial Digital Inputs

Coaxial 1 Digital Input ·, and

Video and/or S-Video Monitor

Component Video 1 Inputs

RZ.

Video 3

Video

DVD Audio/Video

Similarly, it is recommended that you connect any other audio/video device, such as a DVD-Audio or SACD player or HDTV set-top box, to the Video 1, Video 2 or Video 3 sources, or the 6-/8-channel direct inputs, as the are assigned to the Video 1, Video 2, Video 3 and 6-/8-channel source audio inputs by default.

However, you may connect any component video source to either set of component video inputs, as they are assignable to any source.You will still need to connect either the analog or digital audio outputs, or the 6-/8-channel audio outputs, of your component video device to the analog audio inputs corresponding to the source (such as DVD or Video 2 for a cable converter box), or to any of the

Digital Audio Inputs

8. If the component video inputs are used, connect the

Component Video Monitor Outputs ‹ to

the component video inputs of your TV, projector or display device.

9. If you have a camcorder, video game or other audio/video device that is connected to the AVR on a temporary rather than permanent basis, connect the audio, video and digital audio outputs of that device to the front panel. A device connected here is selected as the Video 4 input, and the digital inputs must be assigned to the Video 4 input. (See page 20 for more information on input configuration.)

VIDEO CONNECTION NOTES:

• When the component video jacks are used, the on-

screen menus are not visible and you must switch to the standard composite or S-video input on your TV to view them.

• The AVR 240 will accept either standard composite,

S-video or Y/Pr/Pb component video signals. However, it will not convert any of these signals to a different format.

• When connecting a video source to the AVR 240,

you may use either composite, component or Svideo, but only one type of video may be connected for each device.

• When more than one video format is used, it is

necessary to make a separate connection from the AVR to your video display for each format. For example, if both composite and component sources are connected to the AVR 240, both the

Composite and Component Video Monitor Outputs

priate inputs on your video display.

Component Video 2 Inputs ﬁ

Optical or Coaxial

bg*(.

Video 4 Inputs *(ÓÔ on the

‹V must be connected to the appro-

System and Power Connections

The AVR 240 is designed for flexible use with external control components.

Main Room Remote Control Extension

If the receiver is placed behind a solid or smoked glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, an optional remote sensor may be used. Connect the output of the remote sensor to the Remote IR Input ∞ jack.

If other components are also prevented from receiving remote commands, only one sensor is needed. Simply use this unit’s sensor or a remote eye by running a connection from the the Remote IR Input jack on Harman Kardon or other compatible equipment.

AC Power Connections

This unit is equipped with two accessory AC outlets. They may be used to power accessory devices, but they should not be used with high-current-draw equipment such as power amplifiers.The total power draw to each outlet may not exceed 100 watts.

The

Switched AC Accessory Outlet ‡ will receive

power only when the unit is on. This is recommended for devices that have no power switch or a mechanical power switch that may be left in the “ON” position.

NOTE: Many audio and video products go into a Standby mode when they are used with switched outlets, and cannot be fully turned on using the outlet alone without a remote control command.

The

Unswitched AC Accessory Outlet ° will

receive power as long as the unit is plugged into a powered AC outlet.

Once the

AC Power Cord ﬂ is connected, you are

almost ready to enjoy the AVR 240’s incredible power and fidelity!

Remote IR Output § jack to

16 INSTALLATION AND CONNECTIONS

Page 18

The

Bridge

The

Bridge

The

Bridge

The

Bridge



AVR240 harman/kardon

OPERATION

Basic Operation

Once you have completed the initial setup and configuration of the AVR 240, it is simple to operate and enjoy. The following instructions will help you maximize the enjoyment of your new receiver:

Turning the AVR 240 On or Off

• When using the AVR 240 for the first time, you must first press the panel to turn the unit on. This places the unit in a Standby mode, as indicated by the amber color of the

Power Indicator2. Once the unit is in Standby,

you may begin a listening session by pressing the

Standby/On Switch3on the front panel, or the Power On Button d or AVR Selector f on the

remote.The will turn the unit on and return it to the input source that was last used. The unit may also be turned on from Standby by pressing any of the

Buttons Selector Button

NOTE: After pressing one of the Input Selector Buttons Selector

functions. To turn the unit off at the end of a listening session,

simply press the panel or the Power will be shut off to any equipment plugged into the rear-panel and the Power Indicator 2 will turn amber.

When the remote is used to turn the unit “off” it is actually placing the system in a Standby mode, as indicated by the amber color of the

• To program the AVR 240 for automatic turn-off,

press the press of the button will decrease the time before shut-down in the following sequence:

The sleep time will be displayed in the

Display Line

to one-half brightness when the Sleep function is programmed. To view the current sleep time when the sleep function has been activated, press the

Sleep Button j

normal brightness, and the time until shutdown will appear in the seconds, the message will disappear and the display will return to half-brightness.

•

When the programmed sleep time has elapsed, the unit will automatically turn off. To cancel the Sleep function,

Main Power Switch1on the front

Power Indicator2will turn blue. This

Input Selector

eg on the remote or the Input Source

on the front panel.

eg to turn the unit on, press the AVR

f to set the remote control to the AVR 240

Standby/On Switch 3 on the front

Power Off Button a on the remote.

Switched AC Accessory Outlet ›

Power Indicator 2.

Sleep Button jon the remote. Each

The front-panel display will dim

once.The display will return to

Lower Display Line ı

press and hold the

Sleep Buttonj as

Lower

. After a few

the information display returns to normal brightness; continue to hold the button until the Sleep indicator numbers disappear and the words

OFF

appear in the Lower Display Line Q

SLEEP

When you will be away from home for an extended period of time it is always a good idea to completely turn the unit off with the front-panel

Switch

Main Power

NOTE: All preset memories are lost if the unit is left

turned off by using the

Main Power Switch1for

more than four weeks.

Source Selection

• To select a source, press any of the Input Selector Buttons

remote.

• The input source may also be changed by pressing

the front-panel Each press of the button will move the input selection through the list of available inputs.

• As the input is changed, the AVR 240 will auto-

matically switch to the digital input (if selected), component video input, surround mode, output levels and night mode status as well as any speaker configuration settings established by using the INDEPENDENT Bass Management setting, that were entered during the configuration process for that source.

• When the input source is changed, the new input

name and the digital (or analog) audio input will appear in the current surround mode will appear in the

Display Line

appear momentarily in the on-screen display in the lower third of the screen (semi-OSD).

• When an audio source is selected, the last video

input used remains routed to the

S-Video Outputs Composite Video

‹cV.This permits you to simultaneously view and listen to different sources.This also allows you to choose a video source and then select the

Channel Direct Inputs

• The front-panel

Digital Input

may be used to connect a device such as a video game or camcorder to your home entertainment system on a temporary basis.

• When DMP is selected as the source

and a compatible iPod is inserted in an optional Harman Kardon that is connected to

egde on the

Input Source Selector Button ^.

Upper Display Line P, and the

Lower

ı. The same messages will also

Video 1 Video and

and Component Video,

and S-Video Monitor Outputs

6/8-

as the audio source.

Video 4 Inputs ÓÔ, Optical 3

or the Coaxial 3 Digital Input

DMP Connector e on the rear panel,

navigation messages will appear on any video display connected to the AVR’s

Outputs

cV.The remote control or front-panel controls may be used to navigate the iPod and access many of its functions.These messages will also appear in the front-panel display, and the iPod’s battery may be charged. See the owner’s guides for

and your iPod for more information.

6-Channel/8-Channel Direct Input

• There are two input choices available for use with sources such as a DVD-Audio or SACD player that are connected to the

6/8-Channel Direct Inputs

j. Select the appropriate input according to the way your system and source equipment are configured:

n 6 CH DIRECT should be used when

the SBR and SBL inputs are NOT in use. It is assumed that the input source device has its own internal bass management system. This input passes the input from the source directly through to the volume control without any analog to digital conversion and it mutes the unused input jacks to prevent unwanted noise from interfering with system performance.

n 8 CH DIRECT should be used when an

input is connected to all eight

Inputs

j. It is assumed that the input source device has its own internal bass management system. This input passes the input from the source directly through to the volume control without any analog-to-digital conversion and it mutes the unused input jacks to prevent unwanted noise from interfering with system performance.

Volume Control

• Adjust the volume to a comfortable level using the front-panel

Up/Down Buttons

• To temporarily silence all speaker outputs, press the to all speakers and the headphone jack, but it will not affect any recording or dubbing that may be in progress.When the system is muted, the word MUTE will flash in the Upper Display Line P. Press the normal operation.

(

• You may adjust the bass and treble tone controls at any point during a listening session by pressing the appears in the Lower Display Line ı. Press the TREBLE MODE or BASS MODE

Volume Control Ò or remote Volume

Mute Button f. This will interrupt the output

Mute Button f again to return to

Tone Mode Button 5 until TONE IN

Tone Mode Button 5 again until either

Video Monitor

8-Channel Direct

OPERATION 31

Page 19

AVR240 harman/kardon

OPERATION

appears in the Lower Display Line 5, and then use the

‹/› Buttons ) to boost or cut the low

or high frequencies by up to ±10dB, in 2dB steps, until the desired setting is achieved. You may also totally remove the tone controls from the circuit so that the output is “flat” at any time by pressing the

Tone Mode Button 5 and then pressing the ‹/› Buttons ) so that TONE OUT appears

in the on-screen display and the

Line

ı. The tone controls may also be adjusted using the described on page 21.

• For private listening, plug the 1/4" stereo phone plug from a pair of stereo headphones into the front-panel headphone plug is connected, all speakers will be silenced and across the the headphone output is in the Bypass mode, and to confirm that no processing is being used. When the headphone plug is removed, the audio feed to the speakers will be restored.

• When the headphones are in use, you may take advantage of the Dolby Headphone modes to bring added spaciousness to headphone listening. Press the Surround Mode Group Selector 7 to cycle through the three Dolby Headphone modes and select the one that you prefer.

AUDIO SETUP submenu as

Headphone Jack4. When the

DOLBY H:BP will scroll once

Lower Display Line ı , indicating that

Dolby Mode Select Button w or the

Lower Display

Surround Mode Selection

One of the important features of the AVR 240 is its ability to reproduce a full multichannel surround sound field from digital sources, analog matrix surroundencoded programs and standard stereo programs.

Selection of a surround mode is based on personal taste, as well as the type of program source material being used. For example, motion pictures or TV programs bearing the logo of one of the major surroundencoding processes, such as Dolby Surround or DTS Stereo, may be played in either the Dolby Digital, Dolby Pro Logic II or IIx Movie, DTS Neo:6 Cinema, or Logic 7 5.1 or 7.1 Cinema surround modes.

NOTE: Once a program has been encoded with matrix surround information, it retains the surround information as long as the program is broadcast in stereo.Thus, movies with surround sound may be decoded via any of the analog surround modes such as Dolby Pro Logic IIx Cinema, Logic 7 Cinema or DTS Neo:6 Cinema, when they are broadcast via conventional TV stations, cable, pay-TV and satellite transmission. In addition, a growing number of made-for-television programs, sports broadcasts, radio dramas and music CDs are also recorded in surround sound.

Even when a program is not listed as carrying intentional surround information, you may find that the Dolby Pro Logic IIx, Logic 7 Enhanced or DTS Neo:6, VMAx and the Hall or Theater modes often deliver enveloping surround presentations through the use of the natural information present in all stereo recordings.

Surround modes may be changed at any time by using either the front panel or remote control. Any changes made to the surround mode for that source will be retained in the AVR’s menu, even after another source is selected, or if the AVR is placed in Standby mode.To select a new surround mode from the front panel, first press the

Selector Button

mode group, such as Dolby, DTS or Logic 7, is selected. Next, press the 8 to choose the specific individual surround mode.

To select a surround mode using the remote, press the button for the major surround mode group that includes the mode you wish to choose from:

w, DTS Surround x, DTS Neo:6 S, Logic 7 y, Stereo R or DSP Surround k.

The first press of the button will show the current mode from that group.To cycle through the available modes in that group, press the button again until the desired mode appears in the

ı, the on-screen display and in the Surround Mode Indicators

changes, the appropriate ˆ will light to indicate the current mode. At times, it is possible that more than one indicator will light. This can occur when the DSP Surround Off mode has been selected, or when post-processing is being used with an input signal, such as when the Dolby Digital

2.0 plus Dolby Pro Logic IIx mode is used to create a 7-channel presentation of a two-channel signal.

The Dolby Digital, Dolby Digital EX and DTS 5.1, DTS-ES Matrix and DTS-ES Discrete modes may only be selected when a digital input is in use and a digital signal in that format is present. In addition, when a digital source is present, the AVR 240 will automatically select and switch to the correct mode, regardless of the mode that has been previously selected. For more information on selecting digital sources, see the Digital Audio Playback section.

The Dolby Pro Logic IIx modes are available only when the AVR 240 has been configured for 6.1/7.1 operation by setting the Surround Back speakers as either

LARGE or SMALL as described on page

26. These modes provide a matrixed 6.1-channel presentation of analog sources. See page 26 for more information.

When the 6-channel/8-channel direct inputs are in use there is no surround processing, as these inputs take the analog output signals from an optional, exter-

Surround Mode Group

7 until the desired major surround

Surround Mode Selector Button

Dolby

Lower Display Line

ˆ. As the surround mode

Surround Mode Indicator

nal DVD-Audio or SACD player, or another source device and carry them straight through to the volume control without any further digital processing.

To listen to a program in traditional two-channel stereo, using the front left and front right speakers only (plus the subwoofer, if installed and configured), press the

Stereo ButtonRuntil SURROUND OFF appears in the Lower Display Line ı, or press the Surround Mode Group Selector 7 until the Stereo modes appear in the on-screen display and Lower Display Line Select Button appears in the on-screen display and Lower Display Line

When an analog audio source is in use, you may activate an analog bypass Surround Off mode, if you have removed the tone controls from the processing circuitry by pressing the and using the ‹/› Buttons )o until the

TONE OUT message appears in the Lower Display Line

Normally, the DSP icon will appear in the Surround Mode Indicators ˆ, and the message SURROUND OFF will appear in the lower line of the semi-OSD display.When the DSP icon appears, the incoming signal is digitized and any bass management settings are applied. This mode is recommended when your front speakers are not capable of reproducing the lower frequencies and are thus used with a subwoofer.

When the DSP icon is not lit in Surround Off mode with an analog audio input in use, the AVR is in analog bypass mode.The signal is being routed directly to the volume control, without entering the digital domain and without any bass management settings being applied. This mode is desirable when your left and right speakers are capable of reproducing low frequencies, and when you wish to hear the analog source material in its pure form.

and then press the Surround Mode

8 until SURROUND OFF

Tone Mode Button 5

ı.

Digital Audio Playback

Digital audio is a major advancement over older analog surround processing systems such as Dolby Pro Logic. It delivers five, six or seven discrete channels: left front, center, right front, left surround, right surround and optionally one or two surround back channels. Each channel reproduces full frequency range (20Hz to 20kHz) and offers dramatically improved dynamic range and significant improvements to signal-to-noise ratios. In addition, digital systems have the capability to deliver an additional channel that is specifically devoted to low-frequency information. This is the “.1” channel referred to when you see these systems described as “5.1,” “6.1” or “7.1”.The bass channel is separate from the other channels, but since it is intentionally bandwidth-limited, sound designers have given it that unique designation.

32 OPERATION

Page 20

AVR240 harman/kardon

OPERATION

Dolby Digital

Dolby Digital is a standard part of DVD, and is available on specially encoded LD discs and satellite broadcasts and it is a part of the high-definition television (HDTV) system.

An optional, external RF demodulator is required to use the AVR 240 to listen to the Dolby Digital soundtracks available on laser discs. Connect the RF output of the LD player to the demodulator and then connect the digital output of the demodulator to the Coaxial Inputs *(bg of the AVR 240. No demodulator is required for use with DVD players or DTS-encoded laser discs.

DTS

DTS is another digital audio system that is capable of delivering 5.1 or 6.1 discrete or matrix sound field reproduction. Although both DTS and Dolby Digital are digital, they use different methods of encoding the signals, and thus they require different decoding circuits to convert the digital signals back to analog.

DTS-encoded soundtracks are available on select DVD and LD discs, as well as on special audio-only DTS discs.You may use any LD or CD player equipped with a digital output to play DTS-encoded discs with the AVR 240. All that is required is to connect the player’s output to either an on the rear panel bg or front panel *(.

In order to listen to DVDs encoded with DTS soundtracks, the DVD player must be compatible with the DTS signal as indicated by a DTS logo on the player’s front panel. Early DVD players may not be able to play DTS-encoded DVDs.This does not indicate a problem with the AVR 240, as some players cannot pass the DTS signal through to the digital outputs. If you are in doubt as to the capability of your DVD player to handle DTS discs, consult the player’s owner’s manual.

IMPORTANT NOTE: Many DVD players have a default setting that does not pass through the DTS data, even though the machine is capable of doing so. If your DVD player has the “DTS Digital Out” logo but does not trigger DTS playback in the AVR 240, change the player's settings in the “Audio” or “Bitstream” configuration menu so that DTS playback is enabled. The method for doing this will vary with each player. In some cases, the proper menu choice will be “Original,” while in others it will be “DTS.” Consult the owner's manual for your player to find the specific information to find the proper setting.

Selecting a Digital Source

To utilize either digital mode, you must have properly connected a digital source to the AVR 240. Connect the digital outputs from DVD players, HDTV receivers, satellite systems or CD players to the Coaxial Inputs *(bg. In order to provide a backup signal and a source for analog stereo recording, the analog outputs provided on digital source equipment

Optical or Coaxial Input

Optical or

should also be connected to their appropriate inputs on the AVR 240 rear panel (e.g., connect the analog stereo audio output from a DVD to the on the rear panel when you connect the source’s digital outputs).

If you have not already configured an input for a digital source using the on-screen menus as shown on page 20, first select the input using the remote or frontpanel controls as outlined in this manual. Next, select the digital source by pressing the

Button

q# and then using the ⁄/¤Buttons n on the remote or the‹/›Selector Buttons ) on the front panel to

OPTICAL or COAXIAL appear in the display.When the digital source is playing, the AVR 240 will automatically detect which type of digital data stream is being decoded and display that information in the

Digital Bitstream Indications

When a digital source is playing, the AVR 240 senses the type of bitstream data that is present. Using this information, the correct surround mode will automatically be selected. For example, DTS bitstreams will cause the unit to switch to DTS decoding, and Dolby Digital bitstreams will enable Dolby Digital decoding. When the unit senses PCM data from CDs or LDs, it will default to Logic 7 Music mode, although you may select any of the standard surround modes, such as Dolby Pro Logic II or Logic 7. Since the range of available surround modes is dependent on the type of digital data that is present, the AVR 240 uses a variety of indicators and messages to let you know what type of signal is present. These messages will appear shortly after an input or surround mode is changed, and they will remain in the five seconds before that portion of the display returns to the normal surround mode indication.

Surround Mode Channel Indications

For Dolby Digital and DTS sources, a three-digit indication will appear, showing the number of channels present in the data. An example of this type of display is

3/2/.1.

The first number indicates how many discrete front channel signals are present.

• A “3” tells you that separate front left, center and

front right signals are available.This will be displayed for Dolby Digital 5.1 and DTS 5.1 programs.

• A “2” tells you that separate front left and right

signals are available, but there is no discrete center channel signal. This will be displayed for Dolby Digital bitstreams that have stereo program material.

• A “1” tells you that there is only a mono channel

available in the Dolby Digital bitstream.

Upper Display Line P or on-screen

Upper Display Line P.

Lower Display Line ı for about

DVD Audio Inputs W

Digital Select

choose any of the

inputs, as they

The middle number indicates how many discrete surround channel signals are present.

• A “2” tells you that separate surround left and right signals are available.This will be displayed for Dolby Digital 5.1 and DTS 5.1 programs.

• A “1” tells you that there is only a single, surroundencoded surround channel. This will appear for Dolby Digital bitstreams that have matrix encoding.

• A “0” indicates that there is no surround channel information. This will be displayed for two-channel stereo programs.

The last number indicates whether there is a discrete low-frequency effects (LFE) channel. This is the “.1” in the common abbreviation of “5.1” sound and is a special channel that contains only bass frequencies.

• A “1” tells you that an LFE channel is present. This will be displayed for Dolby Digital 5.1 and DTS 5.1 programs, as available.

• A “0” indicates that there is no LFE channel information available. However, even when there is no dedicated LFE channel, low-frequency sound will be present at the subwoofer output when the speaker configuration is set to show the presence of a subwoofer.

The information in the right side of the display will tell you if the digital audio data contains a special flag signal that will automatically activate the appropriate

6.1 or 7.1 mode.This will be shown as

or EX-OFF for Dolby Digital bitstreams and ES-ON or ES-OFF for DTS bitstreams.

If the EX flag is off, and your receiver has been configured for 6.1/7.1 operation, you may manually turn on EX processing as appropriate by simply selecting the Dolby Digital EX surround mode as described on pages 21 and 32. When the ES flag is not present in a DTS bitstream, you may benefit from a 6.1-channel presentation by selecting the DTS+Neo:6 post-processing surround mode using the procedure described on pages 21 and 32. In that mode, the DTS Neo:6 algorithms will be used to derive the surround back channel from the DTS bitstream information.

When Dolby Digital 3/2/.1 or DTS 3/2/.1 signals are being played, the AVR will automatically switch to the proper surround mode, and no other processing may be selected, with these exceptions:

• When a Dolby Digital 2.0 signal is detected, you may choose to listen to it in its native form. To do so, scroll through the Dolby surround modes until the Stereo icon lights in the

Indicators

Alternatively, you may engage surround post-processing by scrolling through the Dolby Pro Logic II and IIx modes, and the Dolby Pro Logic icon will light in addition to the Dolby Digital icon.

ˆ in addition to the Dolby Digital icon.

EX-ON

Surround Mode

OPERATION 35

Page 21

AVR240 harman/kardon

OPERATION

• As indicated above, when the EX flag is not present in a Dolby Digital bitstream, you may scroll through the Dolby surround modes to manually select Dolby Digital EX processing.

• When a DTS 5.1 signal is detected, you may listen to it as a two-channel presentation, a 5.1-channel presentation or a 6.1-channel presentation (if your AVR is configured for 6.1/7.1 operation). To hear a two-channel presentation, scroll through the DTS surround modes until the Stereo icon lights in the Surround Mode Indicators ˆ in addition to the DTS icon. Continue scrolling to engage DTS 5.1 processing or DTS+Neo:6 (6-channel) processing.

• If a DTS-ES 6.1 Discrete signal is present, you may choose a two-channel presentation, a 5.1-channel presentation or a 6.1-channel presentation (if your AVR has been configured for 6.1/7.1 operation). Scroll through the DTS surround modes until the Stereo icon lights in the

Indicators

Continue scrolling to engage DTS 5.1 processing or DTS-ES Discrete processing.

When a Dolby Digital signal with a 3/1/0 or 2/0/0 signal is detected you may select any of the Dolby surround modes.

See page 40 for information on setting a default surround mode.

It is always a good idea to check the readout for the channel data to make certain that it matches the audio logo information shown on the back of a DVD package. In some cases you will see indication for “2/0/0” even when the disc contains a full 5.1, or 3/2/.1 signal. When this happens, check the audio output settings for your DVD player or the audio menu selections for the specific disc being played to make certain that the player is sending the correct signal to the AVR.

PCM Audio Playback

PCM is the abbreviation for Pulse Code Modulation, which is the type of digital signal used for standard CD playback and other non-Dolby Digital and non-DTS digital sources such as Mini-Disc.The digital circuits in the AVR 240 are capable of high-quality digital-toanalog decoding, and they may be connected directly to the digital audio output of your CD or LD player.

Connections may be made to either the rear-panel

Optical or Coaxial Inputs bg or the front-panel Digital Inputs *(.

To listen to a PCM digital source, first select the input for the desired source (e.g., CD). Next press the

Select Button Buttons n on the remote, or the‹/›Selector Buttons

appears in the

ˆ, in addition to the DTS icon.

#q and then use the ⁄/

) on the front panel, until the desired choice

Upper Display Line P.

Surround Mode

Digital

During PCM playback, you may select any Surround mode except Dolby Digital or DTS.

When a PCM signal is detected, the

Line

ı will briefly show a message with the letters PCM, in addition to a readout of the sampling frequency of the digital signal. In most cases this will be 48kHz, though in the case of specially mastered, high-resolution audio discs you will see a indication.

Speaker/Channel Indicators

In addition to the bitstream indicators, the AVR 240 features a set of unique channel-input indicators that tell you how many channels of digital information are being received and/or whether the digital signal is interrupted. (See Figure 16.)

Figure 16

These indicators are the L/C/R/LFE/SL/SR/SBL/SBR letters that are inside the center boxes of the

Channel Input Indicators

When a standard analog signal is in use, only the “L” and “R” indicators will light, as only left and right channels.

Digital signals, however, may have two, five, six or seven channels, depending on the program material, the method of transmission and the way in which it was encoded. When a digital signal is playing, the letters in these indicators will light in response to the specific signal being received. It is important to note that although Dolby Digital, for example, is referred to as a “5.1” system, not all Dolby Digital DVDs or programs are encoded for 5.1. Thus, it is sometimes normal for a DVD with a Dolby Digital soundtrack to trigger only the “L” and “R” indicators.

NOTE: Many DVD discs are recorded with both “5.1” and “2.0” versions of the same soundtrack.When playing a DVD, always be certain to check the type of material on the disc. Most discs show this information in the form of a listing or icon on the back of the disc jacket. When a disc does offer multiple soundtrack choices, you may have to make some adjustments to your DVD player (usually with the “Audio Select” button or in a menu screen on the disc) to send a full 5.1 feed to the AVR 240. It is also possible for the type of signal feed to change during the course of a DVD playback. In some cases, the menu screens and previews of special material will only be recorded in 2.0 audio, while the main feature is available in 5.1 audio. The AVR 240 will automatically sense changes to the

Lower Display

96kHz

Speaker/

O on the front panel.

analog signals have

bitstream and channel count and reflect them in these indicators.

The letters used by the

Indicators

has been interrupted. This will happen when a digital input source is selected before the playback starts, or when a digital source such as a DVD is paused. The flashing indicators remind you that the playback has stopped due to the absence of a digital signal and not through any fault of the AVR 240. This is normal, and the digital playback will resume once the playback is started again.

Night Mode

A special feature of Dolby Digital is the Night mode, which enables specially encoded Dolby Digital input sources to be played back with full digital intelligibility while reducing the minimum peak level by 1/4 to 1/3. This prevents abruptly loud transitions from disturbing others, without reducing the impact of the digital source.The Night mode is available only when Dolby Digital signals with special data are being played.

The Night mode may be engaged when a Dolby Digital DVD is playing by pressing the

Button Buttons n to select either the middle-range or

full-compression versions of the Night mode.To turn the Night mode off, press the until the message in the lower third of the video display and in the D-RANGE OFF.

The Night mode may also be selected to always be on at either level of compression using the options in the DOLBY menu. See page 22 for information on using the menus to set this option.

IMPORTANT NOTES ON DIGITAL PLAYBACK:

• When the digital playback source is stopped, or in

• Although the AVR 240 will decode virtually all current

• Not all digitally encoded programs contain full 5.1-

O also flash to indicate when a bitstream

l on the remote. Next, press the ⁄/

a pause, fast-forward or chapter-search mode, the digital audio data will momentarily stop, the channel position letters inside the

Indicators

not indicate a problem with either the AVR 240 or the source machine.The AVR 240 will return to digital playback as soon as the data is available and when the machine is in a standard play mode.

DVD movies, CDs and HDTV sources, it is possible that some future digital sources may not be compatible with the AVR 240.

or 6.1-channel audio. Consult the program guide that accompanies the DVD or laser disc to determine which type of audio has been recorded on the disc.The AVR 240 will automatically sense the type

Speaker/Channel Input

Night Mode

⁄/¤

Buttons n

Lower Display Line Q reads

Speaker/Channel Input

O will flash. This is normal and does

36 OPERATION

Page 22

The

Bridge

The

Bridge

The

Bridge

The

Bridge

The

Bridge

The

Bridge

The

Bridge

AVR240 harman/kardon

OPERATION

of digital surround encoding used and adjust to accommodate it.

• When some digital sources are playing, you may not be able to select some of the analog surround modes such as Dolby Pro Logic II or IIx, Dolby 3 Stereo, Hall, Theater or Logic 7.

• When a Dolby Digital or DTS source is playing, it is not possible to make an analog recording using the Tape Outputs £ and Video 1 Audio Outputs Y. However, the digital signals will be passed through to the

Digital Audio Outputs ·a.

Tuner Operation

The AVR 240’s tuner is capable of tuning AM, FM and FM Stereo broadcast stations. Stations may be tuned manually, or they may be stored as favorite station presets and recalled from a 30-position memory.

Station Selection

1. Press the AM/FM Tuner Select Button g on

the remote to select the tuner as an input. The tuner may be selected from the front panel either by pressing the the tuner is active or by pressing the

Selector

2. Press the

Tuner Band Selector ! again to switch between AM and FM so that the desired frequency band is selected.

3. Press the

manual or automatic tuning.

When the button is pressed so that appears in the Lower Display Line ı each press of the the tuner in a scan mode that seeks the next higher- or lower-frequency station with acceptable signal strength. An tion will momentarily appear when the station stops at a stereo FM station, and an indication will momentarily appear when an AM or monaural FM station is tuned. Press the Tuning buttons again to scan to the next receivable station.

When the button is pressed so that appears in the Lower Display Line ı each tap of the Selector will increased or decrease the frequency by one increment. When the tuner receives a strong-enough signal for adequate reception,

MANUAL TUNED will appear in the Lower Display Line

4. Stations may also be tuned directly in either the

automatic or manual mode.To enter a station’s frequency directly, first select the AM or FM band as desired be pressing the

Input Source Selector ^ until

Tuner Band

AM/FM Tuner Select Button g or

Tuner Mode Button&I to select

AUTO

Tuning Selectors 9u will put

AUTO ST TUNED indica-

AUTO TUNED

MANUAL

ı.

AM/FM Tuner Select

g. Next, press the Direct Button J.

Button

Within five seconds of seeing the

DIRECT IN

scroll in the Upper Display Line P, enter the station frequency by pressing the

Numeric Keys

r. If you press an incorrect button while entering a direct frequency, press the

Clear Button W to

start over.

NOTE: When FM reception of a station is weak, audio quality will be increased by switching to Mono mode by pressing the

Tuner Mode Button&I so that

MANUAL appears momentarily in the Lower Display Line

ı and goes out. This will also

activate manual tuning mode.

Preset Tuning

Using the remote, up to 30 stations may be stored in the AVR 240’s memory for easy recall using the front panel controls or the remote.

To enter a station into the memory, first tune the station using the steps outlined above.Then:

1. Press the

Memory Button X on the remote.

Two underscore lines will appear at the far right side of the

2. Within five seconds, press the

Upper Display Line P.

Numeric Keys r

corresponding to the location where you wish to store this station’s frequency. Once entered, the preset number will appear in the

Line

Upper Display

3. Repeat the process after tuning any additional stations to be preset.

Recalling Preset Stations

• To manually select a station previously entered in

the preset memory, press the

Numeric Keys r

that correspond to the desired station’s memory location.

• To manually tune through the list of stored preset

stations one by one, press the

Selector Buttons

$T on the front panel or

Preset Stations

remote.

Recording

In normal operation, the audio or video source selected for listening through the AVR 240 is sent to the record outputs.This means that any program you are watching or listening to may be recorded simply by placing machines connected to the

£ or Video 1 Audio/Video and S-Video Outputs hY in the Record mode.

When a digital audio recorder is connected to the Digital Audio Outputs ·a, you are able to record the digital signal using a CD-R, MiniDisc or other digital recording system.

Tape Outputs

NOTES:

• The digital outputs are active only when a digital signal is present, and they do not convert an analog input to a digital signal, or change the format of the digital signal. In addition, the digital recorder must be compatible with the output signal. For example, the PCM digital input from a CD player may be recorded on a CD-R or MiniDisc, but Dolby Digital or DTS signals may not.

• Please make certain that you are aware of any copyright restrictions on any material you copy. Unauthorized duplication of copyrighted materials is prohibited by federal law.

Using

When Harman Kardon’s (optional) is connected and a compatible iPod®is docked in The Bridge, press the

DMP Selector Button d to choose

the iPod as the input source. Pressing the

Selector Button

d will also activate the AVR remote’s control codes for the iPod, and you may also use the front-panel controls to operate the iPod. You may also select DMP as the source from the front panel by repeatedly pressing the

Source Selector

^ until DMP appears in the

Upper Display Line P, although no Input Indicator

Ú will light.

When The Bridge is properly connected and a compatible iPod is properly docked,

DMP/THE

BRIDGE IS CONNECTED

across the

Upper Display Line P. Once that mes-

sage appears, use the remote or front-panel buttons to control the iPod. See the Function List Table on pages 44–45 for a listing of the remote control buttons that have been programmed to control the iPod. In brief, the

Search Buttons

Reverse Search, Play and Forward

` and the ⁄/¤/‹/›Buttons

no and Set Button p may be used in a sim-

ilar manner to the corresponding controls on the iPod. Additional buttons on the remote may also be used to navigate your iPod’s albums and playlists. Complete details on operating an iPod using and an AVR remote are furnished with .

The front-panel controls may be used to access a limited number of iPod functions. Press the

Button

& to play or pause the current track. The

Tuning Selector 9 may be used to search reverse (left side of button) or forward (right side of button) through the tracks. Press the

Tuner Band Selector ! to call up the iPod’s menu. Press the Preset Station Selectors

$ to scroll, and the Set Button

@ to select. For complete information on using the

AVR’s remote or front-panel controls to operate an iPod, see the instructions packed with The Bridge.

DMP

Input

will scroll

Tuner Mode

OPERATION 37OPERATION 37

Page 23

AVR240 harman/kardon

OPERATION

Output Level Trim Adjustment

Normal output level adjustment for the AVR 240 is established using EzSet+, or the internal test tone, as outlined on pages 29–30. In some cases, however, it may be desirable to adjust the output levels using program material such as a test disc, or a selection you are familiar with.

To adjust the output levels using program material, first set the reference volume for the front left and front right channels using the Volume Control Òb

If you are using a disc with test signals or an external signal generator as the source from which to trim the output levels, you may use a handheld SPL meter to guide you to the correct SPL levels. Set the meter to the C-Weighting Slow scale, and adjust the volume until the meter reads 75dB.

Once the reference level has been set, press the

Channel Select Buttonmand FRONT L LEVEL

will appear in the Lower Display Line

Q and semi-OSD. To change the level, first press the

Set Button p, and then use the ⁄/

Buttonsnto raise or lower the level. DO NOT

use the volume control, as this will alter the reference setting.

Once the change has been made, press the

Button

p and then press the ⁄/¤Buttons to select the next output channel location you wish to adjust. To adjust the subwoofer level, press the

Buttonsnuntil WOOFER LEVEL appears in

the

Lower Display Line Q and on screen.

Set

⁄/¤

to use your external test disc or other source material as the reference.Then, use the

⁄/¤

Buttons n

until the › cursor is next to the TEST TONE SEQ

line so that you may select between automatic and manual movement of the test tone from one channel to the next. When

AUTO appears, the test tone will automatically circulate from one channel to the next, pausing momentarily at each channel. If you adjust the level of any channel, the test tone will remain paused at that channel until several seconds after your last adjustment before continuing to the next channel. When

MANUAL appears, the test tone will

remain paused at the last channel until you use the

⁄/¤ Buttons n to select another channel.

At each channel position, use the

‹/›

Buttons o

to change the output level. Remember, the goal is to have the output level at each channel be equal when heard at the listening position.

If you wish to reset all the levels to their original factory default of 0dB offset, press the

⁄/¤

Buttons

n so that the on-screen cursor is next to the

CHANNEL RESET line and press the ‹/

Buttons o so that the word ON appears.

›

After the levels are reset, resume the procedure outlined above to reset the levels to the desired settings.When all adjustments are done, press the

⁄/¤

Buttons

to move the on-screen ›cursor so that it is next to BACK TO MANUAL SETUP and then press the

Set Button p if you wish to go back to the

manual setup menu to make other adjustments. If you have no other adjustments to make, press the

Button

v to exit the menu system.

OSD

Repeat the procedure as needed until all channels requiring adjustment have been set. When all adjustments have been made and no further adjustments are made for five seconds, the AVR 240 will return to normal operation.

The channel output for any input may also be adjusted using the full-OSD on-screen menu system. First, set the volume to a comfortable listening level using the

Volume Control Òb. Then, press the OSD Button

v to bring up the MASTER MENU

(Figure 1). Press the ¤Button n until the on-

›

screen

cursor is next to the MANUAL

SETUP

the

⁄/¤ Buttons n to scroll to the CHANNEL

ADJUST

display the

line. Press the Set Button p to display

MANUAL SETUP submenu, and use the

line. Press the Set Button p again to

CHANNEL ADJUST submenu.

Once the menu appears on your video screen, first

⁄/¤

use the

›

cursor so that it is next to the TEST TONE

Buttons n to move the on-screen

line. Press the ‹/›Buttons o so that OFF appears.This will turn off the test tone and allow you

NOTE: The output levels may be separately trimmed for each digital and analog surround mode by selecting that mode and following the instructions shown above.

Memory Backup

This product is equipped with a memory backup system that preserves the system configuration information and tuner presets if the unit is accidentally unplugged or subjected to a power outage.This memory will last for approximately four weeks, after which time all information must be reentered.

38 OPERATION

Page 24

AVR240 harman/kardon

TROUBLESHOOTING GUIDE

SYMPTOM CAUSE SOLUTION

Unit does not function when Main • No AC Power • Make certain AC power cord is plugged into Power Switch is pushed a live outlet

• Check to see whether outlet is switch-controlled

Display lights, but no sound • Intermittent input connections • Make certain that all input and speaker connections or picture are secure

•

Mute is on • Press Mute Button f

• Volume control is down • Turn up volume control

No sound from any speaker; • Amplifier is in protection mode • Check speaker wire connections for shorts at receiver and light around power switch is red due to possible short speaker ends

• Amplifier is in protection mode • Contact your local Harman Kardon service center due to internal problems

No sound from surround or • Incorrect surround mode • Select a mode other than Stereo center speakers • Input is monaural • There is no surround information from mono sources

• Incorrect configuration • Check speaker mode configuration

• Stereo or Mono program material • The surround decoder may not create center- or rear-channel

information from nonencoded programs

Unit does not respond to • Weak batteries in remote • Change remote batteries remote commands • Wrong device selected • Press the AVR selector

• Remote sensor is obscured • Make certain front panel sensor is visible to remote

or connect remote sensor

Intermittent buzzing in tuner • Local interference • Move unit or antenna away from computers, fluorescent

lights, motors or other electrical appliances

Letters flash in the channel indicator • Digital audio feed paused • Resume play for DVD display and digital audio stops • Check that Digital Input is selected

In addition to the items shown above, additional information on troubleshooting possible problems with your AVR 240, or installation-related issues, may be found in the list of “Frequently Asked Questions” which is located in the Product Support section of our Web site at www.harmankardon.com.

Processor Reset

In the rare case in which the unit’s operation or the displays seem abnormal, the cause may involve the erratic operation of the system’s memory or microprocessor.

To correct this problem, first unplug the unit from the AC wall outlet and wait at least three minutes. After the pause, reconnect the AC power cord and check the unit’s operation. If the system still malfunctions, a system reset may clear the problem.

NOTE: Resetting the processor will erase any configuration settings you have made for speakers, output levels, surround modes, digital input assignments as well as the tuner presets.The unit will be returned to the factory presets, and all settings for these items must be reentered.

If the system is still operating incorrectly, there may have been an electronic discharge or severe AC line interference that has corrupted the memory or microprocessor.

To clear the AVR 240’s entire system memory including tuner presets, output level settings, delay times and speaker configuration data, first place the AVR in Standby Mode, and then press and hold the

Mode Button

will turn on automatically.

5 button for three seconds. The unit

Tone

56 TROUBLESHOOTING

If these steps do not solve the problem, consult an authorized Harman Kardon service center.

Page 25

AVR240 harman/kardon

Page 26

REFER TO PARTS LIST NEXT PAGE

Page 27

AVR240 harman/kardon

Page 28

AVR240 harman/kardon

AMPLIFIER SECTION BIAS ADJUSTMENT

Measurement condition

. No input signal or volume position is minimum.

Standard value.

. Ideal current = 48mA ( ± 5%) . Ideal DC Voltage = 25.92mV ( ± 5%)

CUP11816Z (VIDEO PCB)

...... ......

VR87

CN81

VR86

CN82

VR82

CN86

VR81

DC VOLTMETER..............Connect to CN81,CN82,CN83,CN84,CN85,CN86,CN87

NO. Channel Adjust for

1 Front Left 25.92mV (±5%)

2 Front Right 25.92mV (±5%)

3 Center

4 Surround Left

5 Surround Right

Surround Back Left

Surround Back Right

25.92mV (±5%)

Adjustment

VR81(ONLY AVR240/340)

CN87

VR83

VR84

VR85

VR86

VR87

VR82

Page 29

AVR240 harman/kardon

harman/kardon Service Bulletin

Service bulletin # HK2006-01 January 2006 To: All harman/kardon Service Centers Models: AVR135, AVR140, AVR240, AVR340,

AVR135/230v, AVR235/230v, AVR335/230v, AVR140/230v, AVR240/230v, AVR340/230v

Subject: Defective Wafer

In the event you receive an AVR135, AVR140, AVR240, AVR340, AVR135/230v, AVR235/230v, AVR335/230v, AVR140/230v, AVR240/230v, or AVR340/230v receiver with the complaint “there is no On Screen Display (OSD) output through the Composite, S-video, or Component Video* connec tions, or no video pass-through from S-Video or Composite connections”, perform the following procedure:

Synopsis: Flat flex cable assembly possibly not making a good contact with defective wafer connector CN72, located on the Input PCB.

Check to see if the affected unit falls into the serial number range(s) below, which may need modification.

1) Remove the top cover

2) Remove the Tuner PCB and Video PCB’s.

3) Remove the Input PCB; replace 16 pin wafer connector CN72 with h/k part# KJP32GA117ZG.

4) Replace all PCB’s in reverse order, and the top cover.

5) Test the unit.

MODEL

AVR135

AVR140

AVR240

AVR340

AVR135 in

CP15 system

AVR235 in

CP25 system

AVR335 in

CP35 system

AVR135/230

AVR235/230

AVR335/230

AVR140/230

AVR240/230

AVR340/230

* Note: For the models above, excluding the AVR340, the full On Screen Display (OSD) norm al l y will not be visible with Com ponent video connections alone. For model AVR340, when the component video jacks are used, the onscreen m enus are not visible with high-definition video (720p or 1080i), and you must switch t o t he standard composite or S-video input on your TV, or t o a 480p video source, to view them.

harman/kardon, Incorporated 250 Crossways Park Dr. Woodbury, New York 11797

SERIAL NUMBER (120V) SERIAL NUMBER (230V) STATUS ACTION

AN0020-28676 to

AN0020-33475

AN0031-04201 to

AN0031-16800

AN0032-01001 to

AN0032-13000

AN0033-01001 to

AN0033-09000

AN0023-08026 to

AN0023-09825

AN0024-03001 to

AN0024-04000

AN0025-04101 to

AN0025-05100

Warranty labor rate: MINOR repair

AN0027-14356 to

AN0027-17965

AN0028-11601 to

AN0028-20300

AN0029-07401 to

AN0029-09830

AN0034-01001 to

AN0034-04600

AN0035-01001 to

AN0035-03400

AN0036-01001 to

AN0036-02200

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

May Need

Modification

Replace Wafer

Page 30

AVR240 harman/kardon

harman/kardon TECH TIPS

Troubleshooting tips and solutions to common service problems

For models: AVR7000/7200/7300/8000 AVR100/200/300/500 AVR110/210/310/510 AVR120/220/320/520 AVR125/225/325/525 AVR130/230/330/430/630 AVR135/235/335/435/635 AVR140/240

Subject: Backup Memory on AVR/DPR/HK series receivers In the event of the complaint: “the receiver is losing its memory (any programmed system settings)

when the unit is turned off, or after the unit is unplugged (briefly*)”:

Check and replace:

Model Designator Location Description Part number

AVR10

AVR7000 C730 Front PCB 0.047 Farad 5.5v capacitor AVR7200 C106 Front PCB 0.047 Farad 5.5v capacitor # P10790-ND

AVR7300 C657 DSP PCB 0.047 Farad 5.5v capacitor # H01-CEZXA0479MN-5 AVR8000 C726 Front PCB 0.047 Farad 5.5v capacitor AVR100/200 C412 Front PCB 0.047 Farad 5.5v capacitor # CEGT-B473J-0J0 AVR300 C906 Front PCB 0.1Farad 5.5v capacitor

AVR500 C906 Front PCB 0.1Farad 5.5v capacitor AVR110/210/310/510

AVR120/220/320/520 AVR125/225 C734,C885 Front PCB two 0.1F capacitors in parallel # BCESOHD104 AVR325/525 C106 Front PCB 0.047 Farad 5.5v capacitor # P10790-ND AVR130/230/330 BAT1 Front PCB 3.6v Battery # HABGP40BVH3A3H AVR135/235/335 BAT1 Front PCB 3.6v Battery # HGP15BNH3A3H AVR140/240 BAT1 Front PCB 3.6v Battery # HABGP40BVH3A3H AVR430/630 C657 DSP PCB 0.047 Farad 5.5v capacitor # CEZXA0479MN-5 AVR435/635 C557 DSP PCB 0.047 Farad 5.5v capacitor # H03-CEZXA0479MN-0 DPR1001 BC601 Main PCB 0.1Farad 5.5v capacitor # CEGT-B104J-0J0

DPR1005/2005 C437 HK3370/3470 C301 Front PCB 0.1Farad 5.5v capacitor # CEGT-B104J-0J0

HK3375/3475 C301 Front PCB 0.1Farad 5.5v capacitor # CEGT-B104J-0J0 HK3250

* After approximately two weeks of being disconnected from AC supply, even a normally functioning receiver may lose any programmed settings and switch to default settings. (Four weeks for the DPR1005 & 2005)

C712 D709

C216 Front PCB 0.047 Farad 5.5v capacitor # P10790-ND

C712 D709

AVR10 DPR1001 DPR1005 DPR2005 HK3370/3470/3375/3475 HK3250

Front PCB

Processor PCB

Front PCB

0.047 Farad 5.5v capacitor and 1N4148 diode

0.047 Farad 5.5v capacitor # CEZXA0479MN-5

0.047 Farad 5.5v capacitor and 1N4148 diode

TIP# HKTT2003-01 Rev6

#3439247315 #2058322101 # P10790-ND or # J3432147324X

# 55230310NR or # P10790-ND

# J4433210421X or # P10791-ND # J4433210421X or # P10791-ND

#3439247315 #2058322101

Page 31

AVR240 harman/kardon

Page 32

AVR240 harman/kardon

AVR240 Electrical Parts List

Ref. Designator Part Number Description Qty

FRONT PCB ASSY (CUP11818Y)

Capacitors

C703 HCBS1H821KBT CAP , CERAMIC 820PF 50V K 1 EA C704 CCEA1VH100T CAP , ELECT 10UF 35V 1 EA C712 CCEA1HH1R0T CAP , ELECT 1UF 50V 1 EA C713 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C714 HCBS1H151KBT CAP , CERAMIC 150PF 50V K 1 EA C715 CCEA1HH4R7T CAP , ELECT 4.7UF 50V 1 EA C716 CCEA1CH331T CAP , ELECT 330UF 16V 1 EA C723 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1 EA C725 HCBS1H473ZFT CAP , CERAMIC 0.047UF 50V Z 1 EA C726 CCEA1CH101T CAP , ELECT 100UF 16V 1 EA C728 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1 EA C729 CCKT1H473ZF CAP , CERAMIC 0.047UF 50V ZF 1 EA C731 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C735 CCEA1CH101T CAP , ELECT 100UF 16V 1 EA C736 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C737 HCBS1H180JCT CAP , CERAMIC 18PF 50V J 1 EA C738 HCBS1H180JCT CAP , CERAMIC 18PF 50V J 1 EA C739 CCEA1AH221T CAP , ELECT 220UF/10V 1 EA C740 CCEA1VH100T CAP , ELECT 10UF 35V 1 EA C793 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1 EA C794 HCBS1H102KBT CAP , CERAMIC 1000PF 50V B 1 EA C795 HCBS1H221KBT CAP , CERAMIC 220PF 50V K 1 EA C796 HCBS1H101KBT CAP , CERAMIC 100PF 50V K 1 EA C859 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C860 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C861 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C875 HCBS1H101KBT CAP , CERAMIC 100PF 50V K 1 EA C876 HCBS1H101KBT CAP , CERAMIC 100PF 50V K 1 EA C877 HCBS1H473ZFT CAP , CERAMIC 0.047UF 50V Z 1 EA C878 HCBS1H473ZFT CAP , CERAMIC 0.047UF 50V Z 1 EA C882 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1 EA C886 CCEA0JH102T CAP , ELECT 1000UF 6.3V 1 EA C891 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C892 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C893 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C896 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C897 CCEA1AH471T CAP , ELECT 470UF 10V 1 EA C901 HCBS1H390JT CAP , CERAMIC 39PF 50V J 1 EA C903 CCEA1HKS2R2T CAP , ELECT 2.2UF 50V KS 1 EA C905 CCEA1HKS2R2T CAP , ELECT 2.2UF 50V KS 1 EA C894 CCEA1CH101T CAP , ELECT 100UF 16V 1 EA

Semiconductors

D724 HVD1SS133MT DIODE 1SS133 1 EA D728 HVD1SS133MT DIODE 1SS133 1 EA D729 HVD1SS133MT DIODE 1SS133 1 EA D730 HVD1SS133MT DIODE 1SS133 1 EA D778 KVD1N4003ST DIODE 1N4003 1 EA D779 HVD1SS133MT DIODE 1SS133 1 EA D780 HVD1SS133MT DIODE 1SS133 1 EA D781 HVD1SS133MT DIODE 1SS133 1 EA D782 KVD1N4003ST DIODE 1N4003 1 EA D783 HVIRE5VL28CATZ DIODE 1SS133 1 EA IC87 HVIRE5VL28CATZ IC , RESET (RE5VL28CATZ) RICOH 1 EA Q701 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q705 HVTKRC107MT TRANSISTOR KRC107M 1 EA

Page 33

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

FRONT PCB ASSY (CUP11818Y)

Q722 HVTKRA107MT TRANSISTOR KRA107M 1 EA Q724 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q725 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q726 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q727 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q728 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q729 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q731 HVTKSA1175YT TRANSISTOR SA1175YT 2 EA Q733 HVTKSC2785YT TRANSISTOR SC2785YT 3 EA Q738 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q739 HVTKTA1271YT TRANSISTOR KTA1271Y 1 EA Q740 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q743 HVTKRA107MT TRANSISTOR KRA107M 1 EA IC72 BVIMB90F482APFG240 IC , FLASH U-COM (MB90F482APFG) FUJITSU 1 EA IC73 HRVNJL34H380A SENSOR , REMOTE (NJL34H380A) SENSOR 1 EA IC75 HVI74ACT04MTR I.C , HEX (74ACT04) FAIRCHILD 1 EA IC83 HVI74ACT04MTR I.C , HEX (74ACT04) FAIRCHILD 1 EA IC84 HVI74ACT04MTR I.C , HEX (74ACT04) FAIRCHILD 1 EA IC85 HVIRH5VT18C I.C , RESET (RH5VT18C) RICOH 1 EA

Resistors

R700 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R701 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R704 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R709 CRD20TJ470T RES , CARBON 47 OHM 1/5W J 1 EA R710 CRD20TJ470T RES , CARBON 47 OHM 1/5W J 1 EA R711 CRD20TJ470T RES , CARBON 47 OHM 1/5W J 1 EA R712 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R713 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R714 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R716 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R718 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R730 CRD20TJ112T RES , CARBON 1.1K OHM 1/5W J 1 EA R731 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R732 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R733 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1 EA R734 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R735 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R736 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1 EA R737 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R738 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R739 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R740 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R742 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R743 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R747 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R750 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R752 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R771 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R772 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R773 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R780 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R781 CRD20TJ123T RES , CARBON 12K OHM 1/5W J 1 EA R782 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R786 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R787 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R789 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R790 CRD20TJ105T RES , CARBON 1M OHM 1/5W J 1 EA R791 CRD20TJ822T RES , CARBON 8.2K OHM 1/5W J 1 EA R792 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA

Page 34

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

FRONT PCB ASSY (CUP11818Y)

R820 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R824 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R825 CRD20TJ681T RES , CARBON 680 OHM 1/5W J 1 EA R881 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R882 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R883 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R884 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R885 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R886 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R887 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R888 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R889 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R890 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R891 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R892 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R893 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R913 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R915 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA

Miscellaneous

L702 HLQ02C100KT COIL , AXAIL 10UH 1 EA BN62 CWB2B904370EN WIRE ASS'Y WIRE 1 EA BN72 HJP32GA179ZJ CONN,FFC 1M/M 32P STR,SMD_JST CONNECTOR 1 EA BN80 CWB2B911420EW WIRE ASS'Y WIRE 1 EA BN81 CWB2B908250BM WIRE , ASS'Y WIRE 1 EA BN84 CWB2B905080EN WIRE ASS'Y WIRE 1 EA BN85 CWB2B903090EN WIRE ASS'Y WIRE 1 EA BN88 CWB2B904070EN WIRE ASS'Y WIRE 1 EA BAT1 HABGP40BVH3A3H BATTERY , RECHARGEABLE BATTERY 1 EA BK71 CMD1A209 BRACKET , FLT BRACKET 1 EA BK72 CMD1A209 BRACKET , FLT BRACKET 1 EA BK73 CMD1A387 BRACKET , PCB BRACKET 1 EA BK74 CMD1A209 BRACKET , FLT BRACKET 1 EA BN15 CWB2B910150EN WIRE ASS'Y WIRE 1 EA CN89 CJP05GA19ZY WAFER, STRAIGHT, 5PIN WIRE 1 EA FIP1 HFLHCA18ML03 F.I.P FIP 1 EA JW85 CWE8202070AA WIRE ASS'Y WIRE 1 EA X701 HOX05000E160C CRYSTAL 5Mhz 1 EA CB72 CWC1B2A32A260B CABLE , CARD CARD CABLE 1 EA

CTB3+10G SCREW SCREW 34 EA CTB3+16GFZ SCREW SCREW 2 EA CTWS3+10G SCREW SCREW 1 EA KHR301 CLAMPER CLAMPER 3 EA CGX1A338MBG27 CAP , VOLUME VOLUME CAP 1 EA CGX1A375ZA ORNAMENT , BADGE ORNAMENT 1 EA KGB1A159Z BADGE , HARMAN/KARDON(TOP) BADGE 1 EA CKC5B145S46Z CABINET , TOP CABINET 1 EA CLZ9Z028Z FERRITE CORE(21.2X6.4X12.7) CORE(K5C T) 3 EA CMH1A214 HOLDER , VOLUME HOLDER 1 EA CMZ2A090 SHEET,VOLUME SHEET 1 EA CTB3+8JFC SCREW SCREW 13 EA CTB4+6FFC SCREW SCREW 6 EA

PCB , MOMS (CUP11818-5)

SW1 CSH1A008ZV SW , PUSH (MOMS) MOMS SWITCH 1 EA CN86 KJP02GA89ZM WAFER WIRE 1 EA

Page 35

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

PCB , POWER KEY (CUP11818-6)

CN88 CJP04GA19ZY WAFER, STRAIGHT, 4PIN WIRE 1 EA D723 CVD50BOBBWGA L.E.D , 2 COLOR (ORG , BLUE) L.E.D 1 EA S701 HST1A020ZT SW , TACT 1A020 1 EA

PCB , DIGITAL INPUT (FRONT) (CUP11818-8)

BN18 CWZAVR125BN18 WIRE ASS'Y (SHIELD) WIRE 1 EA IC76 HVI74HCU04AFNG I.C , INVERTER (74HCU04) TOSHIBA 1 EA JK81 CJJ4M041Y JACK , BOARD (COAX) BOARD 1 EA JK82 HJSTORX177L MODULE , OPTICAL(RX) OPTICAL JACK 1 EA JW83 CWE8202150RV WIRE ASS'Y WIRE 1 EA C807 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V ZF 1 EA C808 CCKT1H181KB CAP , CERAMIC 180PF 50V KB 1 EA C809 CCEA1AH471T CAP , ELECT 470UF 10V 1 EA C812 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1 EA C817 HCBS1H100JCT CAP , CERAMIC 10PF 50V J 1 EA R805 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R806 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R869 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R875 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA

PCB , HEADPHONE JACK (CUP11818-10)

BN92 CWB2B905080EN WIRE ASS'Y WIRE JK83 CJJ2E026Z JACK , HEADPHONE(SILVER PLATE) HEADPHONE JACK 1 EA C783 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1 EA D786 HVD1SS133MT DIODE 1SS133 1 EA D787 HVD1SS133MT DIODE 1SS133 1 EA

PCB , FRONT PANEL KEY (CUP11818-2)

Capacitors

C719 HCBS1H181KBT CAP , CERAMIC 180PF 50V K 1 EA C720 HCBS1H181KBT CAP , CERAMIC 180PF 50V K 1 EA C721 HCBS1H181KBT CAP , CERAMIC 180PF 50V K 1 EA C730 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V ZF 1 EA

Resistors

R744 CRD20TF1002T RES , CARBON 10K F 1/5W 1 EA R745 CRD20TF1002T RES , CARBON 10K F 1/5W 1 EA R746 CRD20TF1002T RES , CARBON 10K F 1/5W 1 EA R753 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R754 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R755 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R756 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1 EA R757 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R758 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R759 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R760 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R761 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R762 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1 EA R763 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R764 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R765 CRD20TJ752T RES , CARBON 7.5K OHM 1/5W J 1 EA R766 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R767 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R768 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA

Page 36

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

PCB , FRONT PANEL KEY (CUP11818-2)

R769 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1 EA

Miscellaneous

BN89 CWB2B905080EN WIRE ASS'Y WIRE 1 EA S702 HST1A020ZT SW , TACT 1A020 1 EA S703 HST1A020ZT SW , TACT 1A020 1 EA S704 HST1A020ZT SW , TACT 1A020 1 EA S705 HST1A020ZT SW , TACT 1A020 1 EA S706 HST1A020ZT SW , TACT 1A020 1 EA S707 HST1A020ZT SW , TACT 1A020 1 EA S708 HST1A020ZT SW , TACT 1A020 1 EA S709 HST1A020ZT SW , TACT 1A020 1 EA S710 HST1A020ZT SW , TACT 1A020 1 EA S711 HST1A020ZT SW , TACT 1A020 1 EA S712 HST1A020ZT SW , TACT 1A020 1 EA S713 HST1A020ZT SW , TACT 1A020 1 EA S714 HST1A020ZT SW , TACT 1A020 1 EA S715 HST1A020ZT SW , TACT 1A020 1 EA S716 HST1A020ZT SW , TACT 1A020 1 EA S717 HST1A020ZT SW , TACT 1A020 1 EA S718 HST1A020ZT SW , TACT 1A020 1 EA S719 HST1A020ZT SW , TACT 1A020 1 EA S720 HST1A020ZT SW , TACT 1A020 1 EA

PCB , VOLUME ENCODER (CUP11818-3)

Capacitors

C805 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C806 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z 1 EA C841 CCEA1VH100T CAP , ELECT 10UF 35V 1 EA C842 CCEA1VH100T CAP , ELECT 10UF 35V 1 EA C843 CCEA1VH100T CAP , ELECT 10UF 35V 1 EA C855 HCBS1H101KBT CAP , CERAMIC 100PF 50V K 1 EA C856 HCBS1H101KBT CAP , CERAMIC 100PF 50V K 1 EA C857 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1 EA C862 HCBS1H101KBT CAP , CERAMIC 100PF 50V K 1 EA C863 HCBS1H101KBT CAP , CERAMIC 100PF 50V K 1 EA C874 HCBS1H101KBT CAP , CERAMIC 100PF 50V K 1 EA

Semiconductors

D701 CVD52CSBBCEAB2 BLUE L.E.D L.E.D 1 EA D703 CVD52CSBBCEAB2 BLUE L.E.D L.E.D 1 EA D705 CVD52CSBBCEAB2 BLUE L.E.D L.E.D 1 EA D774 HVD1SS133MT DIODE 1SS133 1 EA

Resistors

R705 CRD20TJ820T RES , CARBON 82 OHM 1/5W J 1 EA R706 CRD20TJ820T RES , CARBON 82 OHM 1/5W J 1 EA R708 CRD20TJ820T RES , CARBON 82 OHM 1/5W J 1 EA R864 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1 EA R865 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R866 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1 EA R871 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R872 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R873 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R874 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R876 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA

Page 37

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

PCB , VOLUME ENCODER (CUP11818-3)

R877 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R878 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA VR74 CSR2A037Z ENCODER ENCODER 1 EA

Miscellaneous

BN10 CWZAVR230BN10 WIRE ASS'Y (SHIELD) WIRE 1 EA BN41 CWZAVR130BN41 WIRE ASS'Y (SHIELD) WIRE 1 EA CN84 KJP05GB46ZM WAFER WIRE 1 EA JK85 CJJ9M003Z JACK , S-VIDEO S-VIDEO JACK 1 EA JK86 CJJ4S023Y JACK , BOARD BOARD 1 EA JW84 CWE8202110RV WIRE, ASS'Y WIRE 1 EA

PCB , INTERFACE (CUP11818-7)

BN94 KJP13GB99ZM CONNECTOR CONNECTOR 1 EA BN95 KJP08GB99ZM CONNECTOR , HOUSING CONNECTOR 1 EA CN11 KJP08GA98ZM WAFER WIRE 1 EA CN12 KJP15GA98ZM WAFER WIRE 1 EA CN16 CJP06GA19ZY WAFER, STRAIGHT, 6PIN WIRE 1 EA CN79 CJP05GA19ZY WAFER, STRAIGHT, 6PIN WIRE 1 EA IC88 HVINJM2068MDTE1 I.C , OP AMP (NJM2068M) JRC 1 EA C810 CCEA1CH101T CAP , ELECT 100UF 16V 1 EA C811 CCEA1CH101T CAP , ELECT 100UF 16V 1 EA C813 CCEA1VH100T CAP , ELECT 10UF 35V 1 EA C814 CCEA1VH100T CAP , ELECT 10UF 35V 1 EA R778 CRD25TJ1R0T RES , CARBON 1 OHM 1/4W J 1 EA R779 CRD25TJ1R0T RES , CARBON 1 OHM 1/4W J 1 EA R810 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R811 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R813 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R814 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA

INPUT PCB ASS'Y (CUP11814Y)

Capacitors

C105 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C106 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C201 HCUS1H221JA CAP , CHIP 220pF 1 EA C202 HCUS1H221JA CAP , CHIP 220pF 1 EA C203 HCUS1H221JA CAP , CHIP 220pF 1 EA C204 HCUS1H221JA CAP , CHIP 220pF 1 EA C205 HCUS1H221JA CAP , CHIP 220pF 1 EA C206 HCUS1H221JA CAP , CHIP 220pF 1 EA C207 HCUS1H221JA CAP , CHIP 220pF 1 EA C208 HCUS1H221JA CAP , CHIP 220pF 1 EA C209 HCUS1H221JA CAP , CHIP 220pF 1 EA C210 HCUS1H221JA CAP , CHIP 220pF 1 EA C211 HCUS1H221JA CAP , CHIP 220pF 1 EA C212 HCUS1H221JA CAP , CHIP 220pF 1 EA C213 HCUS1H221JA CAP , CHIP 220pF 1 EA C214 HCUS1H221JA CAP , CHIP 220pF 1 EA C215 HCUS1H221JA CAP , CHIP 220pF 1 EA C216 HCUS1H221JA CAP , CHIP 220pF 1 EA C217 HCUS1H221JA CAP , CHIP 220pF 1 EA C218 HCUS1H221JA CAP , CHIP 220pF 1 EA C219 HCUS1H221JA CAP , CHIP 220pF 1 EA C220 HCUS1H221JA CAP , CHIP 220pF 1 EA C221 HCUS1H221JA CAP , CHIP 220pF 1 EA C222 HCUS1H221JA CAP , CHIP 220pF 1 EA

Page 38

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

C223 HCUS1H221JA CAP , CHIP 220pF 1 EA C224 HCUS1H221JA CAP , CHIP 220pF 1 EA C225 HCUS1H221JA CAP , CHIP 220pF 1 EA C226 HCUS1H221JA CAP , CHIP 220pF 1 EA C241 HCUS1H181JA CAP , CHIP 180pF 1 EA C242 HCUS1H471JA CAP , CHIP 470pF 1 EA C253 HCUS1H181JA CAP , CHIP 180pF 1 EA C254 HCUS1H471JA CAP , CHIP 470pF 1 EA C255 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C256 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C270 HCUS1H181JA CAP , CHIP 180pF 1 EA C271 HCUS1H471JA CAP , CHIP 470pF 1 EA C291 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C292 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C293 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C294 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C295 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C296 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C297 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C298 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C309 HCUS1H332KC CAP , CHIP 3300pF 1 EA C310 HCUS1H332KC CAP , CHIP 3300pF 1 EA C311 HCUS1H332KC CAP , CHIP 3300pF 1 EA C312 HCUS1H332KC CAP , CHIP 3300pF 1 EA C313 HCUS1H332KC CAP , CHIP 3300pF 1 EA C314 HCUS1H332KC CAP , CHIP 3300pF 1 EA C315 HCUS1H332KC CAP , CHIP 3300pF 1 EA C316 HCUS1H332KC CAP , CHIP 3300pF 1 EA C317 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C318 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C319 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C320 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C321 HCUS1H561JA CAP , CHIP 560pF 1 EA C322 HCUS1H561JA CAP , CHIP 560pF 1 EA C323 HCUS1H561JA CAP , CHIP 560pF 1 EA C324 HCUS1H561JA CAP , CHIP 560pF 1 EA C325 HCUS1H561JA CAP , CHIP 560pF 1 EA C326 HCUS1H561JA CAP , CHIP 560pF 1 EA C327 HCUS1H561JA CAP , CHIP 560pF 1 EA C328 HCUS1H561JA CAP , CHIP 560pF 1 EA C329 HCUS1H561JA CAP , CHIP 560pF 1 EA C330 HCUS1H561JA CAP , CHIP 560pF 1 EA C331 HCUS1H561JA CAP , CHIP 560pF 1 EA C332 HCUS1H561JA CAP , CHIP 560pF 1 EA C333 HCUS1H561JA CAP , CHIP 560pF 1 EA C334 HCUS1H561JA CAP , CHIP 560pF 1 EA C335 HCUS1H561JA CAP , CHIP 560pF 1 EA C336 HCUS1H561JA CAP , CHIP 560pF 1 EA C337 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C338 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C339 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C340 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C350 HCUS1H332KC CAP , CHIP 3300pF 1 EA C351 HCUS1H332KC CAP , CHIP 3300pF 1 EA C352 HCUS1H332KC CAP , CHIP 3300pF 1 EA C353 HCUS1H332KC CAP , CHIP 3300pF 1 EA C354 HCUS1H332KC CAP , CHIP 3300pF 1 EA C355 HCUS1H332KC CAP , CHIP 3300pF 1 EA C356 HCUS1H332KC CAP , CHIP 3300pF 1 EA C357 HCUS1H332KC CAP , CHIP 3300pF 1 EA C371 HCUS1H221JA CAP , CHIP 220pF 1 EA

Page 39

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

C372 HCUS1H221JA CAP , CHIP 220pF 1 EA C373 HCUS1H221JA CAP , CHIP 220pF 1 EA C374 HCUS1H221JA CAP , CHIP 220pF 1 EA C375 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C376 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C378 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C379 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C381 HCUS1H561JA CAP , CHIP 560pF 1 EA C382 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C383 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C390 HCUS1H471JA CAP , CHIP 470pF 1 EA C391 HCUS1H471JA CAP , CHIP 470pF 1 EA C392 HCUS1H471JA CAP , CHIP 470pF 1 EA C393 HCUS1H471JA CAP , CHIP 470pF 1 EA C394 HCUS1H471JA CAP , CHIP 470pF 1 EA C395 HCUS1H471JA CAP , CHIP 470pF 1 EA C396 HCUS1H471JA CAP , CHIP 470pF 1 EA C397 HCUS1H471JA CAP , CHIP 470pF 1 EA C413 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C414 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C415 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C416 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C417 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C418 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C419 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C420 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C421 HCUS1H151JA CAP , CHIP , 150PFJA 150pF 1 EA C422 HCUS1H151JA CAP , CHIP , 150PFJA 150pF 1 EA C425 HCUS1H151JA CAP , CHIP , 150PFJA 150pF 1 EA C426 HCUS1H102KC CAP , CHIP 1000pF 1 EA C427 HCUS1H151JA CAP , CHIP , 150PFJA 150pF 1 EA C428 HCUS1H151JA CAP , CHIP , 150PFJA 150pF 1 EA C429 HCUS1H151JA CAP , CHIP , 150PFJA 150pF 1 EA C430 HCUS1H151JA CAP , CHIP , 150PFJA 150pF 1 EA C471 HCUS1H181JA CAP , CHIP 180pF 1 EA C472 HCUS1H181JA CAP , CHIP 180pF 1 EA C473 HCUS1H181JA CAP , CHIP 180pF 1 EA C474 HCUS1H181JA CAP , CHIP 180pF 1 EA C701 HCUS1H330JA CAP , CHIP 33pF 1 EA C702 HCUS1H330JA CAP , CHIP 33pF 1 EA C704 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C705 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C707 HCUS1H102KC CAP , CHIP 1000pF 1 EA C708 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C718 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C719 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C722 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C723 HCUS1H473ZF CAP , CHIP 0.047uF 1 EA C725 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C727 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C729 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C731 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C733 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C734 HCUS1H122KC CAP , CHIP 1200pF 1 EA C735 HCUS1H680JA CAP , CHIP 68pF 1 EA C738 HCUS1C105ZF CAP , CHIP 1UF 16V 1 EA C739 HCUS1H103KC CAP , CHIP 0.1uF 1 EA C740 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C742 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C743 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C744 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA

Page 40

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

C745 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C747 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C748 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C750 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C751 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C752 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C754 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C756 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C757 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C758 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C759 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C760 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C761 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C762 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C763 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C765 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C767 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C768 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C769 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C770 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C771 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C772 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C773 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C103 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C104 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C251 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C252 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C261 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C262 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C263 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C264 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C265 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C267 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C268 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C269 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C341 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C342 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C343 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C344 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C345 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C346 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C347 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C348 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C403 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C404 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C405 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C406 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C407 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C408 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C409 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C410 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C433 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C434 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C435 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C436 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C437 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C438 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C439 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C440 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C453 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C454 CCEA1VH100T CAP , ELECT 10UF35V 1 EA

Page 41

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

C455 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C456 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C457 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C458 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C459 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C460 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C703 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C706 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C717 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C720 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C721 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C724 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C726 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C728 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C730 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C732 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C736 CCEA1HH2R2T CAP , ELECT 2.2UF50V 1 EA C737 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C741 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C746 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C749 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C753 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C755 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C764 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C766 CCEA0JH102T CAP , ELECT 1000UF6.3V 1 EA C237 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C238 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C239 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C240 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C349 CCEA1HH1R0T CAP , ELECT 1UF 50V 1 EA

Semiconductors

IC13 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC23 HVITC9164CFG I.C , FUNCTION SW (TC9164CFG) TOSHIBA 1 EA IC24 HVITC9163CFG I.C , FUNCTION SW (TC9163CFG) TOSHIBA 1 EA IC25 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC26 HVITC9162CFG I.C , FUNCTION SW (TC9162CFG) TOSHIBA 1 EA IC31 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC32 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC33 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC34 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC35 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC36 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC37 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC42 HVITC9459BFG I.C , 2CH VOLUME (TC9459BFG) TOSHIBA 1 EA IC43 HVITC9482BFG I.C , 6CH VOLUME (TC9482BFG) TOSHIBA 1 EA IC46 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC47 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC48 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC49 HVINJM2068MDTE1 I.C , OP AMP (NJM2068) JRC 1 EA IC72 HVI74HCU04AFNG I.C , INVERTER (74HCU04) TOSHIBA 1 EA IC73 HVIAK4589VQ-T I.C , CODEC + DIR (AK4589) ASAHI KASEI 1 EA IC74 HVI74LCX32TTR I.C , OR-GATE (74LCX32) FAIRCHILD 1 EA IC75 HVICS49400-CQ I.C , DECODER (CS49400) CIRRUS LOGIC 1 EA IC76 HVIM29W800DT70N240 I.C, 4M FLASH MEMORY (M29W800DT) ST 1 EA IC78 HVINJM2391DL133 I.C , CHIP REG (+3.3V) (NJM2391DL133) JRC 1 EA IC79 HVINJM2391DL125 I.C , CHIP REG (+2.5V) (NJM2391DL125) JRC 1 EA IC77 HVI57V161610ET7 SDRAM 16M 7NS (57V161610ET7) HYNIX 1 EA D201 HVD1SS133MT DIODE 1SS133 1 EA D202 HVD1SS133MT DIODE 1SS133 1 EA

Page 42

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

D203 HVD1SS133MT DIODE 1SS133 1 EA D204 HVD1SS133MT DIODE 1SS133 1 EA D205 HVD1SS133MT DIODE 1SS133 1 EA D206 HVD1SS133MT DIODE 1SS133 1 EA D207 HVD1SS133MT DIODE 1SS133 1 EA D208 HVD1SS133MT DIODE 1SS133 1 EA D209 HVD1SS133MT DIODE 1SS133 1 EA D210 HVD1SS133MT DIODE 1SS133 1 EA D211 HVD1SS133MT DIODE 1SS133 1 EA D212 HVD1SS133MT DIODE 1SS133 1 EA D213 HVD1SS133MT DIODE 1SS133 1 EA D214 HVD1SS133MT DIODE 1SS133 1 EA D215 HVD1SS133MT DIODE 1SS133 1 EA D216 HVD1SS133MT DIODE 1SS133 1 EA D701 KVD1N4003ST DIODE 1N4003 1 EA Q201 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q202 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q203 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q204 HVTKRA107MT TRANSISTOR KRA107M 1 EA

Resistors

RN71 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN72 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN73 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN74 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN75 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN76 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN77 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN78 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN79 CRJ104DJ101T RES, ARRAY, 100R (1608) 100 OHM/1608*4 1 EA RN80 CRJ104DJ330T RES , 4ARRAY (1608*4) 33 OHM/1608*4 1 EA RN81 CRJ104DJ330T RES , 4ARRAY (1608*4) 33 OHM/1608*4 1 EA RN82 CRJ104DJ330T RES , 4ARRAY (1608*4) 33 OHM/1608*4 1 EA RN83 CRJ104DJ330T RES , 4ARRAY (1608*4) 33 OHM/1608*4 1 EA RN84 CRJ104DJ332T RES, ARRAY, 3.3K*4 (1608) 3.3K OHM/1608*4 1 EA RN86 CRJ104DJ103T RES, ARRAY, 10K (1608) 10K OHM/1608*4 1 EA RN87 CRJ104DJ103T RES, ARRAY, 10K (1608) 10K OHM/1608*4 1 EA RN88 CRJ104DJ103T RES, ARRAY, 10K (1608) 10K OHM/1608*4 1 EA RN89 CRJ104DJ103T RES, ARRAY, 10K (1608) 10K OHM/1608*4 1 EA RN90 CRJ104DJ103T RES, ARRAY, 10K (1608) 10K OHM/1608*4 1 EA R101 CRJ10DJ562T RES , CHIP 5.6K OHM 1 EA R102 CRJ10DJ562T RES , CHIP 5.6K OHM 1 EA R103 CRJ10DJ682T RES , CHIP 6.8K OHM 1 EA R104 CRJ10DJ682T RES , CHIP 6.8K OHM 1 EA R105 CRJ10DJ151T RES, CHIP 150 OHM 1 EA R106 CRJ10DJ151T RES, CHIP 150 OHM 1 EA R107 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R108 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R201 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R202 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R203 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R204 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R205 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R206 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R207 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R208 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R209 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R210 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R211 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R212 CRJ10DJ471T RES , CHIP 470 OHM 1 EA

Page 43

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

R213 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R214 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R215 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R216 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R217 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R218 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R219 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R220 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R221 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R222 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R223 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R224 CRJ10DJ272T RES , CHIP 2.7K OHM 1 EA R225 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R226 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R227 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R228 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R229 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R230 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R231 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R232 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R233 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R234 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R235 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R236 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R237 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R238 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R239 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R240 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R241 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R242 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R243 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R244 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R245 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R246 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R247 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R248 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R249 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R250 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R251 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R252 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R265 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R267 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R268 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R269 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R270 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R271 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R272 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R273 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R274 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R275 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R276 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R277 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R278 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R279 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R283 CRJ10DJ331T RES , CHIP 330 OHM 1 EA R284 CRJ10DJ331T RES , CHIP 330 OHM 1 EA R285 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R286 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R287 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R288 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R289 CRJ10DJ184T RES , CHIP 180K OHM 1 EA

Page 44

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

R290 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R291 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R292 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R293 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R301 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R302 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R303 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R304 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R305 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R306 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R307 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R308 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R309 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R310 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R311 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R312 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R313 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R314 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R315 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R316 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R317 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R318 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R319 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R320 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R321 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R322 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R323 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R324 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R325 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R326 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R327 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R328 CRJ10DJ123T RES , CHIP 12K OHM 1 EA R329 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R330 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R331 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R332 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R333 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R334 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R335 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R336 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R337 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R338 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R339 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R340 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R341 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R344 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R345 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R348 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R349 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R352 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R353 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R356 CRJ10DJ122T RES , CHIP 1.2K OHM 1 EA R361 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R362 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R363 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R364 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R365 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R366 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R367 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R368 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R371 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA

Page 45

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

R372 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R373 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R374 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R375 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R376 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R377 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R378 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R379 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R380 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R381 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R382 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R383 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R384 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R385 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R386 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R389 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R390 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R391 CRJ10DJ105T RES , CHIP 1M OHM 1 EA R392 CRJ10DJ105T RES , CHIP 1M OHM 1 EA R393 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R394 CRJ10DJ153T RES , CHIP 15K OHM 1 EA R395 CRJ10DJ153T RES , CHIP 15K OHM 1 EA R396 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R397 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R398 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R403 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R404 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R405 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R406 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R407 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R408 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R409 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R410 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R413 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R414 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R415 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R416 CRJ10DJ912T RES,CHIP(1/10W) 9.1K OHM J 9.1K OHM 1 EA R417 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R418 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R419 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R420 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R423 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R424 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R425 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R426 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R427 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R428 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R429 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R430 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R433 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R434 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R435 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R436 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R437 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R438 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R439 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R440 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R453 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R454 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R455 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R456 CRJ10DJ184T RES , CHIP 180K OHM 1 EA

Page 46

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

R457 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R458 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R459 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R460 CRJ10DJ184T RES , CHIP 180K OHM 1 EA R471 CRJ10DJ272T RES , CHIP 2.7K OHM 1 EA R472 CRJ10DJ272T RES , CHIP 2.7K OHM 1 EA R473 CRJ10DJ272T RES , CHIP 2.7K OHM 1 EA R474 CRJ10DJ272T RES , CHIP 2.7K OHM 1 EA R481 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R482 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R483 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R484 CRJ10DJ123T RES , CHIP 12K OHM 1 EA R485 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R486 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R487 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R488 CRJ10DJ512T RES , CHIP 5.1K OHM 1 EA R491 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R492 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R493 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R494 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R495 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R496 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R497 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R498 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R701 CRJ10DJ0R0T RES , CHIP 0 OHM 1 EA R702 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R703 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R704 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R705 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R707 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R714 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R715 CRJ10DJ104T RES , CHIP 100K OHM 1 EA R716 CRJ10DJ472T RES , CHIP 4.7K OHM 1 EA R717 CRJ10DJ3R3T CHIP RES 3.3 OHM 1 EA R718 CRJ10DJ123T RES , CHIP 12K OHM 1 EA R719 CRJ10DJ473T RES , CHIP 47K OHM 1 EA R720 CRJ10DJ473T RES , CHIP 47K OHM 1 EA R721 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R723 CRJ10DJ2R7T RES , CHIP 2.7 OHM 1 EA R724 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R725 CRJ10DJ473T RES , CHIP 47K OHM 1 EA R726 CRJ10DJ473T RES , CHIP 47K OHM 1 EA R727 CRJ10DJ473T RES , CHIP 47K OHM 1 EA R728 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R759 CRJ10DJ181T RES , CHIP 180 OHM 1 EA R760 CRJ10DJ105T RES , CHIP 1M OHM 1 EA R765 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R766 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R767 CRJ10DJ152T RES , CHIP 1.5K OHM 1 EA R768 CRJ10DJ152T RES , CHIP 1.5K OHM 1 EA R769 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R770 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R771 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R772 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R773 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R774 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R775 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R776 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R777 CRJ10DJ102T RES , CHIP 1K OHM 1 EA R778 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R779 CRJ10DJ103T RES , CHIP 10K OHM 1 EA

Page 47

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

INPUT PCB ASS'Y (CUP11814Y)

R786 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R787 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R788 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R801 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R802 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R803 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R804 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R809 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R810 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R814 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R815 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R817 CRJ10DJ103T RES , CHIP 10K OHM 1 EA R822 CRJ10DJ220T RES, CHIP 22 OHM 1 EA R823 CRJ10DJ101T RES , CHIP 100 OHM 1 EA R824 CRJ10DJ330T RES , CHIP 33 OHM 1 EA R780 CRG2ANJ470H RES , METAL OXIDE FILM 47 OHM 2W J 1 EA R781 CRG2ANJ470H RES , METAL OXIDE FILM 47 OHM 2W J 1 EA R782 CRG2ANJ330H RES , METAL OXIDE FILM 33 OHM 2WJ 1 EA

Miscellaneous

BN11 KJP08GB99ZM CONNECTOR , HOUSING CONNECTOR 1 EA BN12 KJP15GB99ZM WAFER WAFER 1 EA BN42 CWZAVR140BN42 WIRE ASS'Y WIRE 1 EA CN10 CJP04GB46ZY WAFER WAFER 1 EA CN13 CJP13GA115ZY WAFER , CARD CABLE WAFER 1 EA CN15 CJP13GA115ZY WAFER , CARD CABLE WAFER 1 EA CN17 KJP12GB142ZP PIN HEADER PIN HEADER 1 EA CN18 CJP05GA19ZY WAFER, STRAIGHT, 5PIN WIRE 1 EA CN19 CJP03GA19ZY WAFER, STRAIGHT, 3PIN WAFER 1 EA CN72 KJP32GA117ZG WAFER , CARD CABLE WAFER 1 EA CN97 CJP02GA19ZY WAFER, 2PIN WIRE 1 EA L701 HLZ9Z014Z CHIP , BEAD HU-1H4516-600JT 1 EA L702 HLZ9Z014Z CHIP , BEAD HU-1H4516-600JT 1 EA L703 HLZ9Z014Z CHIP , BEAD HU-1H4516-600JT 1 EA L704 HLZ9Z014Z CHIP , BEAD HU-1H4516-600JT 1 EA JK11 CJJ4R019W TERMINAL , IN/OUT TERMINAL JACK 1 EA JK12 CJJ4P014W JACK , IN/OUT JACK 1 EA JK13 CJJ4P014W JACK , IN/OUT JACK 1 EA JK14 CJJ4R019W TERMINAL , IN/OUT TERMINAL JACK 1 EA JK15 CJJ4R037W JACK , BOARD JACK 1 EA JW21 CWE7202090AA WIRE ASS'Y WIRE 1 EA X701 HOX12288E220CS CRYSTAL 12.288MHZ 22PF 1 EA

VIDEO PCB (CUP11849Y)

Capacitors

C401 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C402 CCKT1H101KB CAP , CERAMIC 100PF50V KB 1 EA C403 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C404 CCKT1H101KB CAP , CERAMIC 100PF50V KB 1 EA C405 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C406 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C407 CCKT1H101KB CAP , CERAMIC 100PF50V KB 1 EA C408 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C409 CCKT1H101KB CAP , CERAMIC 100PF50V KB 1 EA C410 CCKT1H101KB CAP , CERAMIC 100PF50V KB 1 EA C411 HCBS1H101KBT CAP , CERAMIC 100PF50V K 1 EA C412 HCBS1H101KBT CAP , CERAMIC 100PF50V K 1 EA C413 HCBS1H101KBT CAP , CERAMIC 100PF50V K 1 EA

Page 48

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

VIDEO PCB (CUP11849Y)

C414 HCBS1H101KBT CAP , CERAMIC 100PF50V K 1 EA C415 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C416 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C417 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C418 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C419 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C420 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C421 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C422 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C423 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C424 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C425 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C426 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C427 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C428 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C429 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C430 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C431 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C432 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C436 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C437 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C438 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C439 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C442 HCBS1H103ZFT CAP , CERAMIC 0.01UF50V Z 1 EA C443 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C444 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C445 HCBS1H103ZFT CAP , CERAMIC 0.01UF50V Z 1 EA C446 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C447 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C448 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C449 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C450 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C451 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C452 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C453 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C454 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C455 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C456 HCBS1H104ZFT CAP , CERAMIC 0.1UF50V Z 1 EA C457 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C458 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C459 HCBS1H104ZFT CAP , CERAMIC 0.1UF50V Z 1 EA C460 HCBS1C272MXT CAP , CERAMIC 2700PF16V 1 EA C461 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C462 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C463 HCBS1H473ZFT CAP , CERAMIC 0.047UF50V Z 1 EA C501 HCBS1H330JT CAP , CERAMIC 33PF 50V 1 EA C502 HCBS1H330JT CAP , CERAMIC 33PF 50V 1 EA C503 HCBS1H181KBT CAP , CERAMIC 180PF50V K 1 EA C504 CCEA1HHR47T CAP , ELECT 0.47UF 50V 1 EA C505 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C506 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C507 CCCT1H220JC CAP , CERAMIC 22PF50V 1 EA C508 CCCT1H270JC CAP , CERAMIC 27PF 50V 1 EA C509 CCEA1HH1R0T CAP , ELECT 1UF 50V 1 EA C510 CCEA1HH1R0T CAP , ELECT 1UF 50V 1 EA C511 HCQI1H682JZT CAP , MYLAR 6800PF50V J 1 EA C512 CCEA1HH0R1T CAP , ELECT 0.1UF 50V 1 EA C513 HCBS1H560JT CAP , CERAMIC 56PF50V J 1 EA C514 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C515 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C517 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA

Page 49

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

VIDEO PCB (CUP11849Y)

C518 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C519 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V ZF 1 EA C523 C3A206 WIRE , COPPER SN95/PB5 , 0.6 C555 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C556 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C557 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C561 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C568 HCBS1H104ZFT CAP , CERAMIC 0.1UF50V Z 1 EA C520 CCEA0JKR3222E CAP , ELECT 2200UF 6.3V 1 EA C590 CCCT1H220JC CAP , CERAMIC 22PF50V 1 EA

Semiconductors

D401 HVD1SS133MT DIODE 1SS133 1 EA D402 HVD1SS133MT DIODE 1SS133 1 EA D403 HVD1SS133MT DIODE 1SS133 1 EA D404 HVD1SS133MT DIODE 1SS133 1 EA D405 HVD1SS133MT DIODE 1SS133 1 EA Q402 HVTKSA733CYT TRANSISTOR KSA733CY 1 EA Q403 HVTKRA107MT TRANSISTOR KRA107M 1 EA Q404 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q405 HVTKSA733CYT TRANSISTOR KSA733CY 1 EA Q406 HVTKRA107MT TRANSISTOR KRA107M 1 EA Q407 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q408 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q409 HVTKRA104MT TRANSISTOR KRA104M 1 EA Q410 HVTKTD1302T TRANSISTOR KTD1302 1 EA Q411 HVTKTD1302T TRANSISTOR KTD1302 1 EA Q412 HVTKRA104MT TRANSISTOR KRA104M 1 EA Q501 HVTKSC2785YT TRANSISTOR KSC2785Y(DEAD) 1 EA Q502 HVTKSA1175YT TRANSISTOR KSA1175Y(DEAD) 1 EA Q556 HVTKSA1175YT TRANSISTOR KSA1175Y(DEAD) 1 EA Q568 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q569 HVTKRC107MT TRANSISTOR KRC107M 1 EA IC41 HVINJM2296M I.C , VIDEO SW (NJM2296M) JRC 1 EA IC42 HVINJM2296M I.C , VIDEO SW (NJM2296M) JRC 1 EA IC43 HVINJM2296M I.C , VIDEO SW (NJM2296M) JRC 1 EA IC44 HVIHCF4053M013T I.C (HCF4053) TRIPLE 2 CHAN MULTPLX ST 1 EA IC45 HVIHCF4053M013T I.C (HCF4053) TRIPLE 2 CHAN MULTPLX ST 1 EA IC46 HVINJM2581MTE1 I.C (NJM2581M) 3ch VIDEO AMPLIFIER JRC 1 EA IC47 HVIMM1511XNRE IC, Y/C-MIX (MM1511) VIDEO SWITCH MITSUMI 1 EA IC48 CVIL7805CPNA I.C, REGULATOR (L7805CP) ASS'Y 1 EA IC49 CVIL7905CPNA I.C, REGULATOR (L7905CP) ASS'Y 1 EA IC51 HVILC74763M I.C , OSD (LC74763M) SANYO 1 EA IC52 HVI74ACT04MTR I.C , HEX (74ACT04) FAIRCHILD 1 EA

HVIL7905CP I.C, REGULATOR (L7905CP) ST 1 EA

Resistors

R401 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R402 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R403 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R404 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R405 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R406 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R407 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R408 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R409 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R410 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R411 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R412 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA

Page 50

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

VIDEO PCB (CUP11849Y)

R413 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R414 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R415 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R416 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R417 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R418 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R419 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R420 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R421 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R422 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R423 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R424 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R425 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R426 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R427 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R428 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R430 CRD20TJ1R8T RES , CARBON 1.8 OHM 1/5W J 1 EA R431 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R432 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J 1 EA R433 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R434 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R435 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R436 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R437 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R438 CRD25TJ1R0T RES , CARBON 1 OHM 1/4W J 1 EA R439 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R440 CRD20TJ1R8T RES , CARBON 1.8 OHM 1/5W J 1 EA R441 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R442 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R443 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R444 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R445 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J 1 EA R446 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R447 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R448 CRD20TJ1R8T RES , CARBON 1.8 OHM 1/5W J 1 EA R449 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R450 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R451 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R452 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R453 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J 1 EA R454 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R455 CRD20TJ105T RES , CARBON 1M OHM 1/5W J 1 EA R456 CRD20TJ680T RES , CARBON 68 OHM 1/5W J 1 EA R457 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R458 CRD20TJ123T RES , CARBON 12K OHM 1/5W J 1 EA R459 CRD20TJ680T RES , CARBON 68 OHM 1/5W J 1 EA R460 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R461 CRD20TJ123T RES , CARBON 12K OHM 1/5W J 1 EA R462 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R463 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R464 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R465 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R466 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R467 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R468 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R469 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R470 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R471 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R472 CRD20TJ151T RES , CARBON 150 OHM 1/5W J 1 EA R473 CRD20TJ181T RES , CARBON 180 OHM 1/5W J 1 EA R474 CRD20TJ1R8T RES , CARBON 1.8 OHM 1/5W J 1 EA

Page 51

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

VIDEO PCB (CUP11849Y)

R475 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J 1 EA R476 CRD25TJ101T RES , CARBON 100 OHM 1/4W J 1 EA R477 CRD20TJ2R2T RES , CARBON 2.2 OHM 1/5W J 1 EA R478 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R479 CRD20TJ181T RES , CARBON 180 OHM 1/5W J 1 EA R480 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R481 CRD20TJ183T RES , CARBON 18K OHM 1/5W J 1 EA R484 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R485 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R501 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R502 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R503 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R504 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R505 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R506 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R507 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R508 CRD20TJ682T RES , CARBON 6.8K OHM 1/5W J 1 EA R509 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R510 CRD20TJ393T RES , CARBON 39K OHM 1/5W J 1 EA R511 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R512 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA R513 CRD20TJ822T RES , CARBON 8.2K OHM 1/5W J 1 EA R514 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R516 CRD20TJ202T RES , CARBON 2K OHM 1/5W J 1 EA R517 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R555 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R556 CRD20TJ183T RES , CARBON 18K OHM 1/5W J 1 EA R558 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R568 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R569 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA

Miscellaneous

L501 HLQ02C101JT COIL , AXAIL 100UH,J 1 EA L502 KLQ5R6J405T COIL, PEAKING(RADIAL) 5.6UH J 4X5 1 EA BN14 CWB4F232450PU WIRE ASS'Y WIRE 1 EA BN91 CWB4FE53130PU WIRE ASS'Y WIRE 1 EA CN41 CJP06GA19ZY WAFER, STRAIGHT, 6PIN WIRE 1 EA CN43 CJP13GA115ZY WAFER , CARD CABLE WAFER 1 EA CN61 CJP03GA19ZY WAFER, STRAIGHT, 3PIN WAFER 1 EA ET04 CMD1A569 BRACKET , PCB BRACKET 1 EA ET05 CMD1A569 BRACKET , PCB BRACKET 1 EA

CMY1A218 HEAT SINK(TR) HEAT SINK 1 EA CTB3+8J SCREW SCREW 1 EA HVIL7805CP I.C, REGULATOR (L7805CP) ST 1 EA CMY1A218 HEAT SINK(TR) HEAT SINK 1 EA

CTB3+8J SCREW SCREW 1 EA JK41 CJJ9N001Z JACK , S-VIDEO (2P/H) S-VIDEO JACK 1 EA JK42 CJJ9N001Z JACK , S-VIDEO (2P/H) S-VIDEO JACK 1 EA JK43 CJJ9S001Z JACK , S-VIDEO (3P/H) S-VIDEO JACK 1 EA JK48 CJJ4N043Z JACK , BOARD JACK 1 EA JK49 CJJ4N043Z JACK , BOARD JACK 1 EA JK50 CJJ4S010Z JACK , BOARD JACK 1 EA JW11 CWEP202110VV WIRE WIRE 1 EA X501 HOX14318E220C CRYSTAL 14.318Mhz 1 EA

CHG1A218 CUSHION CUSHION 1 EA

OUTLET PCB (CUP11849-7)

C124 HCQE2E104KDE CAP , LINE ACROSS 0.1UF 1 EA

Page 52

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

OUTLET PCB (CUP11849-7)

CN21 KJP02GA89ZM WAFER WAFER 1 EA CN84 KJP02KA060ZY WAFER WAFER 1 EA F901 KBA2D2500TLET FUSE 2.5A 1 EA F902 KBA2D2500TLET FUSE 2.5A 1 EA F907 KJCFC5S HOLDER , FUSE HOLDER 2 EA OL91 KJJ7A015Z OUTLET , AC(UL/2P/SEP) OUTLET 1 EA

REMOTE PCB (CUP11849-12)

C953 HCBS1H104ZFT CAP , CERAMIC 0.1UF50V Z 1 EA CN88 CJP04GA19ZY WAFER, STRAIGHT, 4PIN WIRE 1 EA D952 HVD1SS133MT DIODE 1SS133 1 EA D953 HVD1SS133MT DIODE 1SS133 1 EA IC95 BVIKP1010B IC, PHOTO COUPLER COSMO 1 EA JK94 CJJ2D008Z JACK , STEREO JACK 1 EA JK95 CJJ2D008Z JACK , STEREO JACK 1 EA Q995 HVTKRA107MT TRANSISTOR KRA107M 1 EA R952 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R953 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R954 CRD20TJ470T RES , CARBON 47 OHM 1/5W J 1 EA R955 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA

COMPONENT PCB (CUP11849-2)

Capacitors

C601 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C602 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C603 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C604 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C605 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C606 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C607 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C608 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C609 HCBS1H220JCT CAP , CERAMIC 22PF50V J 1 EA C610 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C611 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C612 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C613 CCEA1CH101T CAP , ELECT 100UF16V 1 EA

Semiconductors

IC61 HVINJM2586AMTE1 I.C , VIDEO SW (NJM2586A) JRC 1 EA

Resistors

R601 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R602 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R603 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R604 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R605 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R606 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R607 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R608 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R609 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R610 CRD20TJ4R7T RES , CARBON 4.7 OHM 1/5W 1 EA R611 CRD20TJ4R7T RES , CARBON 4.7 OHM 1/5W 1 EA R612 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA

Page 53

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

COMPONENT PCB (CUP11849-2)

Miscellaneous

BN61 CWB2B903150EN WIRE ASS'Y WIRE 1 EA CN62 CJP04GA19ZY WAFER, STRAIGHT, 4PIN WIRE 1 EA JK61 CJJ4L009Z JACK 9P (RRR/BBB/GGG) JACK 1 EA

DIGITAL IN/OUT PCB (CUP11849-3)

Capacitors

C701 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C702 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C703 CCKT1H181KB CAP , CERAMIC 180PF50V KB 1 EA C704 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V ZF 1 EA C705 CCKT1H181KB CAP , CERAMIC 180PF50V KB 1 EA C706 HCBS1H104ZFT CAP , CERAMIC 0.1UF50V Z 1 EA C707 CCKT1H101KB CAP , CERAMIC 100PF50V KB 1 EA C708 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C709 HCBS1H104ZFT CAP , CERAMIC 0.1UF50V Z 1 EA C711 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C712 HCBS1H473ZFT CAP , CERAMIC 0.047UF50V Z 1 EA

Semiconductors

IC71 HVI74HCU04AFNG I.C , INVERTER (74HCU04) TOSHIBA 1 EA

Resistors

R701 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R702 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J 1 EA R703 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R704 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J 1 EA R705 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R706 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R707 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R708 CRD20TJ241T RES, CARBON 240OHM 1/5W J 1 EA R709 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R710 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J 1 EA R711 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J 1 EA R713 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R714 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R715 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R716 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R717 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R718 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R719 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R720 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA

Miscellaneous

BN17 KJP12GB143ZP DIP SOCKET SOCKET 1 EA JK71 HJSTORX177L MODULE , OPTICAL(RX) OPTICAL JACK 1 EA JK72 HJSTORX177L MODULE , OPTICAL(RX) OPTICAL JACK 1 EA JK73 CJJ4S022Z JACK , BOARD JACK 1 EA JK74 HJSTOTX177L MODULE , OPTICAL(TX) OPTICAL JACK 1 EA

POWER TRANS PCB (CUP11849-4,5)

Capacitors

C107

CCKT1H103ZF CAP , CERAMIC 0.01UF50V ZF 1 EA

Page 54

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

POWER TRANS PCB (CUP11849-4,5)

C108 C109 C110 C111 C112 C117 C118 C119 C120 C121 C122 C921 C922 C923 C924 C925 C926 C927 C928 C931 C932 C933 C934

Semiconductors

D101 D102 D104 D105 D108 D109 D111 D991 D992

Q104

CCKT1H103ZF CAP , CERAMIC 0.01UF50V ZF 1 EA

CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V ZF 1 EA

CCKT1H103ZF CAP , CERAMIC 0.01UF50V ZF 1 EA

CCEA1HH4R7T CAP , ELECT 4.7UF50V 1 EA

CCKT1H103ZF CAP , CERAMIC 0.01UF50V ZF 1 EA

CCEA1JH470TS CAP , ELECT 63V/47UF/105'C 1 EA

CCKT1H103ZF CAP , CERAMIC 0.01UF50V ZF 1 EA

CCEA2AH101E CAP , ELECT 100UF 1 EA

HCQI1H104JZT CAP , MYLAR 0.1UF50V J 1 EA

HCQI1H103JZT CAP , MYLAR 0.01UF50V J 1 EA

HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA

HVDMTZJ15BT DIODE , ZENER 15V 1/2W 1 EA

HVDMTZJ27BT DIODE , ZENER 27V 1/2W 1 EA

HVD1N5819T DIODE , SCHOTTKY 1N5819 1 EA

KVD1N4003ST DIODE 1N4003 1 EA

HVDMTZJ12BT DIODE , ZENER 12V 1/2W 1 EA

CVDKBU804FMA BRIDGE DIODE ASS'Y ASS'Y 1 EA

HVDKBU804F DIODE , BRIDGE BRIDGE DIODE 1 EA

HVTKSC2316YT TRANSISTOR KSC2316Y 1 EA

Resistors

R101 R104 R105 R106 R107 R108 R109 R110 R112 R113

Miscellaneous

BN96 CN13 CN19 CN20 CN81

KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA

KRQ1AJR47H RES , FUSE 0.47 OHM 1W J 1 EA

CRQ1AJR33H RES , FUSE 0.33 OHM 1W J 1 EA

CRD20TJ4R7T RES , CARBON 4.7 OHM 1/5W 1 EA

CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA

CRD20TJ4R7T RES , CARBON 4.7 OHM 1/5W 1 EA

CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J 1 EA

CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA

CWB1C908150BM WIRE ASS'Y WIRE 1 EA

CJP05GA01ZY CON WAFER YMW025-05R CONNECTOR 1 EA

KJP03GA90ZM WAFER WAFER 1 EA

KJP04GA90ZM WAFER WAFER 1 EA

CJP08GA01ZY WAFER, STRAIGHT, 8PIN WAFER 1 EA

CMY1A219 HEAT SINK (BRIDGE DIODE) HEAT SINK 1 EA

CTB3+12J SCREW SCREW 1 EA

Page 55

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

POWER TRANS PCB (CUP11849-4,5)

CMY1A219 HEAT SINK (BRIDGE DIODE) HEAT SINK 1 EA

CTB3+12J SCREW SCREW 1 EA F903 F904 F905 F906 F907 KBA2C6300TLUZ FUSE 6.3A 250V 1 EA

SW91

BIAS & REGULATOR PCB (CUP11849-6,8)

Capacitors

C851 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C852 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C853 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C854 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C855 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C856 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C857 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C929 CCEA1VH332F CAP , ELECT (ANGLE) 3300UF 35V 1 EA C930 CCEA1VH222F CAP,ELEC (ANGLE) 2200UF 35V 1 EA C935 CCKT1H223ZF CAP , CERAMIC 0.022UF 50V ZF 1 EA C936 CCKT1H223ZF CAP , CERAMIC 0.022UF 50V ZF 1 EA C937 CCKT1H223ZF CAP , CERAMIC 0.022UF 50V ZF 1 EA C938 CCEA1EH101T CAP , ELECT 100UF25V 1 EA C939 CCEA1EH101T CAP , ELECT 100UF25V 1 EA C940 CCEA1EH101T CAP , ELECT 100UF25V 1 EA C941 CCEA1CKR3103E CAP , ELECT 10000UF , 16V 1 EA C942 CCEA1HH2R2T CAP , ELECT 2.2UF50V 1 EA

KBA2C8000TLU FUSE 8.0A 250V 1 EA

KBA2C6300TLUZ FUSE 6.3A 250V 1 EA

KJCFC5S HOLDER , FUSE HOLDER for F903-906 2 EA

KST1A010Z SW , TACT CN SWITCH 1 EA

Semiconductors

D904 KVD1N4003ST DIODE 1N4003 1 EA D905 KVD1N4003ST DIODE 1N4003 1 EA D906 KVD1N4003ST DIODE 1N4003 1 EA D907 KVD1N4003ST DIODE 1N4003 1 EA D915 HVD1SS133MT DIODE 1SS133 1 EA D916 HVD1SS133MT DIODE 1SS133 1 EA D917 HVDSB2100 DIODE , SCHOTTKY SB2100 1 EA D918 HVDSB2100 DIODE , SCHOTTKY SB2100 1 EA IC91 HVIL7815CP I.C, REGULATOR (L7815CP) ST 1 EA IC92 HVIL7915CP I.C, REGULATOR (L7915CP) ST 1 EA IC93 HVIL7805CP I.C, REGULATOR (L7805CP) ST 1 EA Q851 HVTKTD600KGR TRANSISTOR , BIAS KTD600KGR 1 EA Q852 HVTKTD600KGR TRANSISTOR , BIAS KTD600KGR 1 EA Q853 HVTKTD600KGR TRANSISTOR , BIAS KTD600KGR 1 EA Q854 HVTKTD600KGR TRANSISTOR , BIAS KTD600KGR 1 EA Q855 HVTKTD600KGR TRANSISTOR , BIAS KTD600KGR 1 EA Q856 HVTKTD600KGR TRANSISTOR , BIAS KTD600KGR 1 EA Q857 HVTKTD600KGR TRANSISTOR , BIAS KTD600KGR 1 EA

Resistors

R874 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R875 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R876 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA

Page 56

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

BIAS & REGULATOR PCB (CUP11849-6,8)

R877 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R878 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R879 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R880 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R882 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J 1 EA R883 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J 1 EA R884 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J 1 EA R885 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J 1 EA R886 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J 1 EA R887 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J 1 EA R888 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J 1 EA R912 CRD20TJ153T RES , CARBON 15K OHM 1/5W J 1 EA R913 CRD20TJ153T RES , CARBON 15K OHM 1/5W J 1 EA R914 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA VR81 HVN1RA221B01T RES , SEMI FIXED(220 OHM) 220 OHM 1 EA VR82 HVN1RA221B01T RES , SEMI FIXED(220 OHM) 220 OHM 1 EA VR83 HVN1RA221B01T RES , SEMI FIXED(220 OHM) 220 OHM 1 EA VR84 HVN1RA221B01T RES , SEMI FIXED(220 OHM) 220 OHM 1 EA VR85 HVN1RA221B01T RES , SEMI FIXED(220 OHM) 220 OHM 1 EA VR86 HVN1RA221B01T RES , SEMI FIXED(220 OHM) 220 OHM 1 EA VR87 HVN1RA221B01T RES , SEMI FIXED(220 OHM) 220 OHM 1 EA

Miscellaneous

BN97 CWB2B902200EN WIRE ASS'Y WIRE 1 EA CN31 CJP02GB46ZY WAFER, ANGLE, 2PIN WAFER 1 EA CN32 CJP02GB46ZY WAFER, ANGLE, 2PIN WAFER 1 EA CN33 CJP02GB46ZY WAFER, ANGLE, 2PIN WAFER 1 EA CN34 CJP02GB46ZY WAFER, ANGLE, 2PIN WAFER 1 EA CN35 CJP02GB46ZY WAFER, ANGLE, 2PIN WAFER 1 EA CN36 CJP02GB46ZY WAFER, ANGLE, 2PIN WAFER 1 EA CN37 CJP02GB46ZY WAFER, ANGLE, 2PIN WAFER 1 EA CN96 CJP08GA01ZY WAFER, STRAIGHT, 8PIN WAFER 1 EA CN98 HJP08GB131ZK WAFER WAFER 1 EA

MIC & H/P PCB (CUP11849-9)

Capacitors

C820 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C821 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C822 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C823 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C824 HCBS1H471KBT CAP , CERAMIC 470PF 50V 1 EA C825 HCBS1H151KBT CAP , CERAMIC 150PF50V K 1 EA C826 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C827 HCBS1H223ZFT CAP , CERAMIC 0.022UF50V Z 1 EA C828 HCBS1H470JT CAP , CERAMIC 47PF50V J 1 EA C829 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C830 HCBS1H473ZFT CAP , CERAMIC 0.047UF50V Z 1 EA C849 HCBS1H471KBT CAP , CERAMIC 470PF 50V 1 EA C850 HCBS1H471KBT CAP , CERAMIC 470PF 50V 1 EA C866 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C867 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C868 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C869 CCEA1EH470T CAP , ELECT 47UF25V 1 EA C870 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C871 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C872 CCEA1CH331T CAP , ELECT 330UF16V 1 EA C873 CCEA1CH331T CAP , ELECT 330UF16V 1 EA

Page 57

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MIC & H/P PCB (CUP11849-9)

Semiconductors

D801 HVDMTZJ5.6BT DIODE , ZENER 5.6V 1/2W 1 EA D802 HVDMTZJ5.6BT DIODE , ZENER 5.6V 1/2W 1 EA D803 HVD1SS133MT DIODE 1SS133 1 EA

IC86 HVINJM4556AL I.C , HEADPHONE (NJM4556A) JRC 1 EA IC87 HVINJM2068MDTE1 I.C , OP AMP (NJM2068M) JRC 1 EA IC88 HVIHCF4053M013T I.C (HCF4053) TRIPLE 2 CHAN MULTPLX ST 1 EA Q734 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q735 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q736 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q737 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q738 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q739 HVTKRA107MT TRANSISTOR KRA107M 1 EA Q740 HVTKRC107MT TRANSISTOR KRC107M 1 EA

Resistors

R895 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R896 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R897 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R898 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R899 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R900 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R901 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R902 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R903 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R904 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R905 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R906 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R907 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R908 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R909 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R910 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R911 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R915 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R918 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R919 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R920 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R921 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R922 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R923 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R924 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R925 CRD20TJ680T RES , CARBON 68 OHM 1/5W J 1 EA R926 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R927 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R928 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R929 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R930 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R931 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R932 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R933 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R934 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R935 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R936 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R937 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R957 CRD20TJ101T RES , CARBON 100 OHM 1/5W J 1 EA R958 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA

Page 58

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MIC & H/P PCB (CUP11849-9)

Miscellaneous

CN15 CJP08GA19ZY WAFER, STRAIGHT, 8PIN WIRE 1 EA CN82 KJP06HA37ZM WAFER WIRE 1 EA CN85 CJP03GA19ZY WAFER, STRAIGHT, 3PIN WAFER 1 EA CN92 CJP05GA19ZY WAFER, STRAIGHT, 5PIN WIRE 1 EA BN16 CWZAVR140BN16 WIRE ASS'Y (SHIELD) WIRE 1 EA BN19 CWZAVR335BN19 WIRE ASS'Y WIRE 1 EA BN44 CWB2B904350EN WIRE ASS'Y WIRE 1 EA RL81 HSL4A011ZE RELAY OMI-SS-212L 1 EA

REMOTE IN/OUT PCB (CUP11849-12)

C953 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1 EA CN88 CJP04GA19ZY WAFER, STRAIGHT, 4PIN WAFER 1 EA D952 HVD1SS133MT DIODE 1SS133T 1 EA D953 HVD1SS133MT DIODE 1SS133T 1 EA IC95 BVIKP1010B IC, PHOTO COUPLER (KP1010B) COSMO 1 EA JK94 CJJ2D008Z JACK , STEREO JACK 1 EA JK95 CJJ2D008Z JACK , STEREO JACK 1 EA Q995 HVTKRA107MT TRANSISTOR KRA107M 1 EA R952 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R953 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R954 CRD20TJ470T RES , CARBON 47 OHM 1/5W J 1 EA R955 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA

IPOD PCB (CUP11834Y)

Capacitors

C400 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C401 HCUS1H104ZF CAP , CHIP 0.1uF 1 EA C402 HCUS1H471JA CAP , CHIP 470pF 1 EA C403 HCUS1H471JA CAP , CHIP 470pF 1 EA C408 HCEC1CRV2100T CAP , ELEC (SMD) 10UF / 16V 1 EA C409 HCEC1CRV2100T CAP , ELEC (SMD) 10UF / 16V 1 EA C410 HCEC1HRV21R0T CAP , ELEC (SMD) 1UF / 50V 1 EA C411 HCEC1HRV21R0T CAP , ELEC (SMD) 1UF / 50V 1 EA C416 HCUS1H473ZF CAP , CHIP 0.047uF 1 EA C421 HCUS1H471JA CAP , CHIP 470pF 1 EA C422 HCUS1H471JA CAP , CHIP 470pF 1 EA C423 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C424 HCUS1H223KC CAP , CHIP 0.022uF 1 EA C417 CCEA1CH471T CAP , ELECT 470UF16V 1 EA

Semiconductors

D400 HVD1SS355T DIODE , CHIP 1SS355 1 EA D401 HVD1SS355T DIODE , CHIP 1SS355 1 EA IC41 HVITC9215AF I.C (TC9215AF) HI V ANALOG SWITCH TOSHIBA 1 EA Q400 HVTKRC102S TRANSISTOR, CHIP KRC102S 1 EA Q402 HVTKRC102S TRANSISTOR, CHIP KRC102S 1 EA D402 KVD1N4003ST DIODE 1N4003 1 EA

Resistors

R400 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R401 CRJ10DJ4R7T RES , CHIP 4.7 OHM 1 EA R402 CRJ10DF5493T RES , CHIP 549KOHM/1608/1% 49K OHM/1608/1% 1 EA R403 CRJ10DJ0R0T RES , CHIP 0 OHM 1 EA R404 CRJ10DJ470T RES , CHIP 47 OHM 1 EA

Page 59

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

IPOD PCB (CUP11834Y)

R405 CRJ10DJ470T RES , CHIP 47 OHM 1 EA R406 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R407 CRJ10DJ474T RES, CHIP 470K OHM 1 EA R412 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R413 CRJ10DJ471T RES , CHIP 470 OHM 1 EA R419 CRJ10DJ332T RES , CHIP 3.3K OHM 1 EA R421 CRJ10DJ223T RES , CHIP 22K OHM 1/5W J 1 EA R422 CRJ10DJ224T RES , CHIP 220K OHM 1 EA

Miscellaneous

JK40 HJJ9L003Z JACK , IPOD IPOD JACK 1 EA CN42 CJP05GB46ZY WAFER WAFER 1 EA CN44 CJP04GB46ZY WAFER WAFER 1 EA ET01 CMD1A570 BRACKET , PCB BRACKET 1 EA R416 CLZ9Z068Z COIL,CHOKE CHOKE COIL 1 EA

CHG1A306 CUSHION CUSHION 1 EA

MAIN PCB (CUP11579W)

Capacitors

C501 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C502 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C503 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C504 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C505 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C506 CCKT1H331KB CAP , CERAMIC 330PF50V KB 1 EA C507 CCKT1H331KB CAP , CERAMIC 330PF50V KB 1 EA C508 CCKT1H331KB CAP , CERAMIC 330PF50V KB 1 EA C509 CCKT1H331KB CAP , CERAMIC 330PF50V KB 1 EA C510 CCKT1H331KB CAP , CERAMIC 330PF50V KB 1 EA C561 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C562 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C564 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C566 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C567 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C568 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C569 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C570 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C571 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C572 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C573 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C574 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C575 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C601 CCCT1H120JC CAP , CERAMIC 12PF50V JC 1 EA C602 CCCT1H120JC CAP , CERAMIC 12PF50V JC 1 EA C603 CCCT1H120JC CAP , CERAMIC 12PF50V JC 1 EA C604 CCCT1H120JC CAP , CERAMIC 12PF50V JC 1 EA C605 CCCT1H120JC CAP , CERAMIC 12PF50V JC 1 EA C606 CCCT1H330JC CAP , CERAMIC 33PF50V JC 1 EA C607 CCCT1H330JC CAP , CERAMIC 33PF50V JC 1 EA C608 CCCT1H330JC CAP , CERAMIC 33PF50V JC 1 EA C609 CCCT1H330JC CAP , CERAMIC 33PF50V JC 1 EA C610 CCCT1H330JC CAP , CERAMIC 33PF50V JC 1 EA C681 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C682 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C683 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C684 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C685 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C721 CCKT1H221KB CAP , CERAMIC 220PF50V KB 1 EA

Page 60

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

C722 CCKT1H221KB CAP , CERAMIC 220PF50V KB 1 EA C723 CCKT1H221KB CAP , CERAMIC 220PF50V KB 1 EA C724 CCKT1H221KB CAP , CERAMIC 220PF50V KB 1 EA C725 CCKT1H221KB CAP , CERAMIC 220PF50V KB 1 EA C726 CCKT1H221KB CAP , CERAMIC 220PF50V KB 1 EA C727 CCKT1H221KB CAP , CERAMIC 220PF50V KB 1 EA C728 CCKT1H221KB CAP , CERAMIC 220PF50V KB 1 EA C801 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C802 CCEA1HH100T CAP , ELECT 10UF 50V 1 EA C803 CCCT1H330JC CAP , CERAMIC 33PF50V JC 1 EA C804 CCCT1H330JC CAP , CERAMIC 33PF50V JC 1 EA C805 CCCT1H120JC CAP , CERAMIC 12PF50V JC 1 EA C806 CCCT1H120JC CAP , CERAMIC 12PF50V JC 1 EA C811 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C812 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C813 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C814 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C815 CCKT1H331KB CAP , CERAMIC 330PF50V KB 1 EA C816 CCKT1H331KB CAP , CERAMIC 330PF50V KB 1 EA C817 CCEA1VH100T CAP , ELECT 10UF35V 1 EA C818 CCEA1VKS100T CAP , ELECT 10UF 35V 1 EA C819 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C820 HCBS1H681KBT CAP , CERAMIC 680PF 50V 1 EA C900 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C901 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C905 CCKT1H223ZF CAP , CERAMIC 0.022UF 50V ZF 1 EA C907 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C908 CCKT1H223ZF CAP , CERAMIC 0.022UF 50V ZF 1 EA C910 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C911 CCEA1CH471T CAP , ELECT 470UF16V 1 EA C912 CCEA1EH221T CAP , ELECT 220UF25V 1 EA C913 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V ZF 1 EA C914 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C917 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C918 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C919 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C924 HCBS1H104ZFT CAP , CERAMIC 0.1UF50V Z 1 EA C925 HCBS1H104ZFT CAP , CERAMIC 0.1UF50V Z 1 EA C932 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C933 CCEA1EH221T CAP , ELECT 220UF25V 1 EA C934 CCKT1H223ZF CAP , CERAMIC 0.022UF 50V ZF 1 EA C939 CCEA1HH4R7T CAP , ELECT 4.7UF50V 1 EA C940 CCEA1AH471T CAP , ELECT 470UF10V 1 EA C950 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C971 HCQI1H562JZT CAP , MYLAR 5600PF50V J 1 EA C972 HCQI1H562JZT CAP , MYLAR 5600PF50V J 1 EA C973 HCQI1H562JZT CAP , MYLAR 5600PF50V J 1 EA C974 HCQI1H562JZT CAP , MYLAR 5600PF50V J 1 EA C975 HCQI1H562JZT CAP , MYLAR 5600PF50V J 1 EA C980 HCQI1H562JZT CAP , MYLAR 5600PF50V J 1 EA C981 HCQI1H562JZT CAP , MYLAR 5600PF50V J 1 EA C990 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C991 CCEA1HH1R0T CAP , ELECT 1UF 50V 1 EA C992 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C993 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C994 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C995 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C996 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C997 HCQI1H473JZT CAP , MYLAR 0.047UF50V J 1 EA C999 CCKT1H223ZF CAP , CERAMIC 0.022UF 50V ZF 1 EA C563 CCEA1CH101T CAP , ELECT 100UF16V 1 EA

Page 61

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

C565 CCEA1CH101T CAP , ELECT 100UF16V 1 EA C631 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C632 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C633 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C634 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C635 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C636 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C637 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C638 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C639 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C640 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C807 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C808 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C809 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C810 CCEA1JH101E CAP , ELECT 100UF63V 1 EA C902 CCET50VKL4822NK CAP , ELECT 8200UF/50V 1 EA C904 KCKDKS472ME CAP , CERAMIC(X1/Y2/SC) 0.0047UF/2.5KV 1 EA C906 CCEA1EH102E CAP , ELECT 1000UF25V 1 EA C909 CCET50VKL4822NK CAP , ELECT 8200UF/50V 1 EA C915 CCET50VKL4103NK CAP , ELECT 10000UF/50V 1 EA C916 CCET50VKL4103NK CAP , ELECT 1000UF/50V 1 EA

Semiconductors

D501 HVD1SS133MT DIODE 1SS133 1 EA D502 HVD1SS133MT DIODE 1SS133 1 EA D503 HVD1SS133MT DIODE 1SS133 1 EA D504 HVD1SS133MT DIODE 1SS133 1 EA D505 HVD1SS133MT DIODE 1SS133 1 EA D581 HVD1SS133MT DIODE 1SS133 1 EA D582 HVD1SS133MT DIODE 1SS133 1 EA D583 HVD1SS133MT DIODE 1SS133 1 EA D584 HVD1SS133MT DIODE 1SS133 1 EA D585 HVD1SS133MT DIODE 1SS133 1 EA D601 HVD1SS133MT DIODE 1SS133 1 EA D801 HVD1SS133MT DIODE 1SS133 1 EA D802 HVD1SS133MT DIODE 1SS133 1 EA D803 HVD1SS133MT DIODE 1SS133 1 EA D804 HVD1SS133MT DIODE 1SS133 1 EA D901 KVD1N4003ST DIODE 1N4003 1 EA D902 HVD1SS133MT DIODE 1SS133 1 EA D911 HVD1SS133MT DIODE 1SS133 1 EA D912 HVD1SS133MT DIODE 1SS133 1 EA D914 HVD1SS133MT DIODE 1SS133 1 EA D917 HVD1SS133MT DIODE 1SS133 1 EA D953 HVD1SS133MT DIODE 1SS133 1 EA D954 KVD1N4003SRT DIODE TW 1N4003 1 EA D955 KVD1N4003SRT DIODE TW 1N4003 1 EA D961 KVD1N4003ST DIODE 1N4003 1 EA D962 KVD1N4003ST DIODE 1N4003 1 EA D963 KVD1N4003ST DIODE 1N4003 1 EA D964 HVD1SS133MT DIODE 1SS133 1 EA D967 HVD1SS133MT DIODE 1SS133 1 EA D968 HVD1SS133MT DIODE 1SS133 1 EA D969 HVD1SS133MT DIODE 1SS133 1 EA D971 HVD1SS133MT DIODE 1SS133 1 EA D972 HVD1SS133MT DIODE 1SS133 1 EA D973 HVD1SS133MT DIODE 1SS133 1 EA D974 HVD1SS133MT DIODE 1SS133 1 EA Q501 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q502 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA

Page 62

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

Q503 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q504 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q505 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q511 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q512 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q513 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q514 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q515 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q516 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q517 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q518 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q519 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q520 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q541 HVTKTC3198YT TRANSISTOR KTC3198Y 1 EA Q542 HVTKTC3198YT TRANSISTOR KTC3198Y 1 EA Q543 HVTKTC3198YT TRANSISTOR KTC3198Y 1 EA Q544 HVTKTC3198YT TRANSISTOR KTC3198Y 1 EA Q545 HVTKTC3198YT TRANSISTOR KTC3198Y 1 EA Q556 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q557 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q558 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q559 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q560 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q561 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q562 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q563 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q564 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q565 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q601 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q602 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q603 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q604 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q605 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q681 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q682 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q683 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q684 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q685 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q701 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q702 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q703 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q704 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q705 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q706 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q707 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q708 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q801 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q802 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q812 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q813 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q814 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q815 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q816 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q817 HVTKTA1268GRT TRANSISTOR KTA1268GR 1 EA Q818 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q819 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q820 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q821 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q822 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q823 HVTKTC3200GRT TRANSISTOR KTC3200GR 1 EA Q824 HVTKTC3198YT TRANSISTOR KTC3198Y 1 EA

Page 63

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

Q825 HVTKTC3198YT TRANSISTOR KTC3198Y 1 EA Q826 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q827 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q901 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q911 HVTKTA1271YT TRANSISTOR KTA1271Y 1 EA Q912 HVTKTA1271YT TRANSISTOR KTA1271Y 1 EA Q913 HVTKTA1271YT TRANSISTOR KTA1271Y 1 EA Q914 HVTKTA1271YT TRANSISTOR KTA1271Y 1 EA Q915 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q916 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q917 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q918 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q938 HVTKRA107MT TRANSISTOR KRA107M 1 EA Q939 HVTKRA107MT TRANSISTOR KRA107M 1 EA Q942 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q943 KVTKSC2785YT TRANSISTOR KSC2785Y 1 EA Q951 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q952 HVTKRA107MT TRANSISTOR KRA107M 1 EA Q960 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q961 HVTKTA1024YT TRANSISTOR KTA1024Y 1 EA Q969 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q970 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q971 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q972 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q973 HVTKTC2874BT TRANSISTOR , MUTE KTC2874B 1 EA Q991 HVTKRC107MT TRANSISTOR KRC107M 1 EA Q992 HVTKRA107MT TRANSISTOR KRA107M 1 EA Q652 HVT2SB1560-OKM TRANSISTOR , POWER 2SB1560 1 EA Q653 HVT2SB1560-OKM TRANSISTOR , POWER 2SB1560 1 EA Q654 HVT2SB1560-OKM TRANSISTOR , POWER 2SB1560 1 EA Q655 HVT2SB1560-OKM TRANSISTOR , POWER 2SB1560 1 EA Q657 HVT2SD2390-OKM TRANSISTOR , POWER 2SD2390 1 EA Q658 HVT2SD2390-OKM TRANSISTOR , POWER 2SD2390 1 EA Q659 HVT2SD2390-OKM TRANSISTOR , POWER 2SD2390 1 EA Q660 HVT2SD2390-OKM TRANSISTOR , POWER 2SD2390 1 EA Q661 HVT2SB1560-OKM TRANSISTOR , POWER 2SB1560 1 EA Q670 HVT2SD2390-OKM TRANSISTOR , POWER 2SD2390 1 EA Q803 HVT2SD2390-OKM TRANSISTOR , POWER 2SD2390 1 EA Q804 HVT2SB1560-OKM TRANSISTOR , POWER 2SB1560 1 EA Q805 HVT2SD2390-OKM TRANSISTOR , POWER 2SD2390 1 EA Q807 HVT2SB1560-OKM TRANSISTOR , POWER 2SB1560 1 EA IC94 HVIMC7805C I.C, REGULATOR (MC7805) FAIRCHILD 1 EA Q858 HVT2SA1360O TRANSISTOR 2SA1360O 1 EA Q871 HVT2SA1360O TRANSISTOR 2SA1360O 1 EA Q872 HVT2SA1360O TRANSISTOR 2SA1360O 1 EA Q874 HVT2SA1360O TRANSISTOR 2SA1360O 1 EA Q875 HVT2SA1360O TRANSISTOR 2SA1360O 1 EA Q876 HVT2SA1360O TRANSISTOR 2SA1360O 1 EA Q877 HVT2SA1360O TRANSISTOR 2SA1360O 1 EA Q881 HVT2SC3423O TRANSISTOR 2SC3423O 1 EA Q882 HVT2SC3423O TRANSISTOR 2SC3423O 1 EA Q883 HVT2SC3423O TRANSISTOR 2SC3423O 1 EA Q884 HVT2SC3423O TRANSISTOR 2SC3423O 1 EA Q885 HVT2SC3423O TRANSISTOR 2SC3423O 1 EA Q886 HVT2SC3423O TRANSISTOR 2SC3423O 1 EA Q887 HVT2SC3423O TRANSISTOR 2SC3423O 1 EA

Resistor

R501 CRD20TJ433T RES , CARBON 43K OHM 1/5W J 1 EA R502 CRD20TJ433T RES , CARBON 43K OHM 1/5W J 1 EA

Page 64

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

R503 CRD20TJ433T RES , CARBON 43K OHM 1/5W J 1 EA R504 CRD20TJ433T RES , CARBON 43K OHM 1/5W J 1 EA R505 CRD20TJ433T RES , CARBON 43K OHM 1/5W J 1 EA R506 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R507 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R508 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R509 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R510 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R511 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R512 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R513 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R514 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R515 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R516 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R517 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R518 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R519 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R520 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R521 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R522 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R523 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R524 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R525 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R531 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R532 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R533 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R534 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R535 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R536 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R537 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R538 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R539 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R540 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R541 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA R542 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA R543 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA R544 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA R545 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA R556 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R557 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R558 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R559 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R560 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R561 CRD20TJ162T RES , CARBON 1.6K OHM 1/5W J 1 EA R562 CRD20TJ162T RES , CARBON 1.6K OHM 1/5W J 1 EA R564 CRD20TJ162T RES , CARBON 1.6K OHM 1/5W J 1 EA R566 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R567 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R568 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R569 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R570 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R571 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R572 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R573 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R574 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R575 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R576 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R577 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R578 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R579 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R580 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA

Page 65

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

R581 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R582 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R583 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R584 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R585 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R586 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R587 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R588 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R589 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R590 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R591 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R592 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R593 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R594 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R595 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R596 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R597 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R598 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R599 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R600 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R601 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R602 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R603 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R604 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R605 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R606 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R607 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R608 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R609 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R610 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R611 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R612 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1 EA R631 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R632 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R633 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R634 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R635 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R636 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R637 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R638 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R639 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R640 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R646 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R647 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R648 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R649 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R650 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R651 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R652 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R653 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R654 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R655 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R666 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R667 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R668 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R669 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R670 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R671 CRD20TJ911T RES , CARBON 910 OHM 1/5W J 1 EA R672 CRD20TJ911T RES , CARBON 910 OHM 1/5W J 1 EA R673 CRD20TJ911T RES , CARBON 910 OHM 1/5W J 1 EA R674 CRD20TJ911T RES , CARBON 910 OHM 1/5W J 1 EA

Page 66

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

R675 CRD20TJ911T RES , CARBON 910 OHM 1/5W J 1 EA R676 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R677 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R678 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R679 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R680 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R681 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R682 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R683 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R684 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R685 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R686 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R687 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R688 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R689 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R690 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R696 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R697 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R698 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R699 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R700 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R701 CRD20TJ821T RES , CARBON 820 OHM 1/5W J 1 EA R702 CRD20TJ821T RES , CARBON 820 OHM 1/5W J 1 EA R703 CRD20TJ821T RES , CARBON 820 OHM 1/5W J 1 EA R704 CRD20TJ821T RES , CARBON 820 OHM 1/5W J 1 EA R705 CRD20TJ821T RES , CARBON 820 OHM 1/5W J 1 EA R706 CRD20TJ821T RES , CARBON 820 OHM 1/5W J 1 EA R707 CRD20TJ821T RES , CARBON 820 OHM 1/5W J 1 EA R708 CRD20TJ821T RES , CARBON 820 OHM 1/5W J 1 EA R711 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R712 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R713 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R714 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R715 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R716 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R717 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R718 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R721 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R722 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R723 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R724 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R725 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R726 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R727 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R728 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R771 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R772 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R773 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R774 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R775 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R776 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R777 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R781 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R782 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R783 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R784 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R785 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R786 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R787 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1 EA R801 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R802 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA

Page 67

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

R803 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R804 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R805 CRD20TJ911T RES , CARBON 910 OHM 1/5W J 1 EA R807 CRD20TJ911T RES , CARBON 910 OHM 1/5W J 1 EA R808 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R809 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J 1 EA R812 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R813 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R814 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R815 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R817 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R818 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R819 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R820 KRD25FJ3R3T RES , CARBON 3.3 OHM 1/4W J 1 EA R821 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R822 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R823 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R824 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R830 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R831 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R832 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R833 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R834 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R835 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R836 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R837 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R838 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R839 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R840 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R841 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R842 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R843 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R844 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R845 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R848 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R849 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R850 CRD20TJ162T RES , CARBON 1.6K OHM 1/5W J 1 EA R851 CRD20TJ162T RES , CARBON 1.6K OHM 1/5W J 1 EA R852 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R853 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R854 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R855 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R856 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R857 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R858 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R859 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1 EA R860 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA R861 CRD20TJ271T RES , CARBON 270 OHM 1/5W J 1 EA R862 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R863 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1 EA R864 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R865 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R866 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R867 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R868 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R869 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R870 CRD20TJ433T RES , CARBON 43K OHM 1/5W J 1 EA R871 CRD20TJ433T RES , CARBON 43K OHM 1/5W J 1 EA R872 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R873 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1 EA R900 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA

Page 68

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

R901 CRD25TJ393T RES , CARBON 39K OHM 1/4W J 1 EA R902 CRD25TJ393T RES , CARBON 39K OHM 1/4W J 1 EA R903 CRD25TJ393T RES , CARBON 39K OHM 1/4W J 1 EA R906 CRD25TJ393T RES , CARBON 39K OHM 1/4W J 1 EA R910 CRD20TJ105T RES , CARBON 1M OHM 1/5W J 1 EA R911 CRD25TJ680T RES , CARBON 68 OHM 1/4W J 1 EA R917 CRD25TJ393T RES , CARBON 39K OHM 1/4W J 1 EA R918 CRD25TJ393T RES , CARBON 39K OHM 1/4W J 1 EA R919 CRD25TJ393T RES , CARBON 39K OHM 1/4W J 1 EA R920 CRD25TJ393T RES , CARBON 39K OHM 1/4W J 1 EA R921 KRD25FJ180T RES , CARBON 18 OHM 1/4W F 1 EA R922 CRD25TJ470T RES , CARBON 47 OHM 1/4W J 1 EA R924 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R925 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R926 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R927 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R928 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R929 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R930 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R931 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R932 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R933 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R934 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1 EA R935 CRD20TJ154T RES , CARBON 150K OHM 1/5W J 1 EA R936 CRD20TJ184T RES , CARBON 180K OHM 1/5W J 1 EA R939 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R940 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1 EA R941 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R942 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R943 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R944 CRD25TJ223T RES , CARBON 22K OHM 1/4W J 1 EA R945 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R946 CRD25TJ223T RES , CARBON 22K OHM 1/4W J 1 EA R947 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R952 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R953 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R954 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R955 CRD20TJ203T RES , CARBON 20K OHM 1/5W J 1 EA R956 CRD20TJ394T RES , CARBON 390K OHM 1/4W J 1 EA R957 CRD20TJ153T RES , CARBON 15K OHM 1/5W J 1 EA R958 CRD20TJ563T RES , CARBON 56K OHM 1/5W J 1 EA R959 CRD20TJ223T RES , CARBON 22K OHM 1/5W J 1 EA R960 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1 EA R961 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R962 CRD20TJ273T RES , CARBON 27K OHM 1/5W J 1 EA R963 CRD20TJ105T RES , CARBON 1M OHM 1/5W J 1 EA R966 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R969 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R970 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R971 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R972 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R973 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1 EA R974 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R975 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R976 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R977 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R978 CRD20TJ331T RES , CARBON 330 OHM 1/5W J 1 EA R979 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R980 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R981 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R982 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA

Page 69

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

R983 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1 EA R986 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1 EA R987 CRD20TJ561T RES , CARBON 560 OHM 1/5W J 1 EA R988 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R991 CRD20TJ822T RES , CARBON 8.2K OHM 1/5W J 1 EA R992 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J 1 EA R998 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1 EA R563 CRD20TJ162T RES , CARBON 1.6K OHM 1/5W J 1 EA R565 CRD20TJ162T RES , CARBON 1.6K OHM 1/5W J 1 EA R656 CRF5EKR27HX2K RES , CEMENT 0.27ohm X 2 1 EA R657 CRF5EKR27HX2K RES , CEMENT 0.27ohm X 2 1 EA R658 CRF5EKR27HX2K RES , CEMENT 0.27ohm X 2 1 EA R659 CRF5EKR27HX2K RES , CEMENT 0.27ohm X 2 1 EA R660 CRF5EKR27HX2K RES , CEMENT 0.27ohm X 2 1 EA R810 CRF5EKR27HX2K RES , CEMENT 0.27ohm X 2 1 EA R811 CRF5EKR27HX2K RES , CEMENT 0.27ohm X 2 1 EA R904 HRDERC12UGK335T RES , CARBONJP 3.3M OHM 1 EA R905 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1 EA R923 CRD25TJ220T RES , CARBON 22 OHM 1 EA R990 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1 EA R993 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1 EA R994 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1 EA R995 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1 EA R996 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1 EA R997 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1 EA R999 CRG1ANJ100H RES , METAL OXIDE FILM 10 OHM 1 EA

Miscellaneous

CMYAVR235 HEAT SINK ASS'Y ASS'Y 1 EA

CHD1A012 SCREW , TR SCREW 21 EA

CHD1A036FZ SCREW , SPECIAL SCREW 4 EA

CHD3A012 SCREW , TR SCREW 3 EA

CMD1A398 BRACKET , PCB BRACKET 2 EA

CMD1A417 BRACKET , PCB BRACKET 2 EA

CMD1A488 BRACKET , FAN BRACKET 1 EA

CMY1A249 HEAT SINK HEAT SINK 2 EA

CMY2A205 HEAT SINK,SUB HEAT SINK 1 EA

CTB3+10J SCREW SCREW 6 EA

CTB3+8J SCREW SCREW 9 EA

HDMKD1206PTS3 MOTOR , FAN(60X60X25MM) FAN 1 EA BN19 CWB3FE03250UP WIRE ASS'Y WIRE 1 EA BN20 CWB3FB43280UP WIRE ASS'Y WIRE 1 EA BN79 CWZAVR230BN79 WIRE ASS'Y (SHIELD) WIRE 1 EA BN81 CWB1C902050EN WIRE ASS'Y WIRE 1 EA BN82 CWB1C902050EN WIRE ASS'Y WIRE 1 EA BN83 CWB1C902050EN WIRE ASS'Y WIRE 1 EA BN84 CWB1C902050EN WIRE ASS'Y WIRE 1 EA BN85 CWB1C902050EN WIRE ASS'Y WIRE 1 EA BN86 CWB1C902050EN WIRE ASS'Y WIRE 1 EA BN87 CWB1C902050EN WIRE ASS'Y WIRE 1 EA BN88 CWB2B904070EN WIRE ASS'Y WIRE 1 EA BN98 HJP08GA130ZK WAFER WAFER 1 EA CN61 KJP02GA01ZM WAFER WAFER 1 EA CN62 KJP02GA01ZM WAFER WAFER 1 EA CN63 KJP02GA01ZM WAFER WAFER 1 EA CN64 KJP02GA01ZM WAFER WAFER 1 EA CN65 KJP02GA01ZM WAFER WAFER 1 EA CN66 KJP02GA01ZM WAFER WAFER 1 EA CN67 KJP02GA01ZM WAFER WAFER 1 EA CN80 KJP11GA19ZM WAFER WAFER 1 EA

Page 70

AVR240 harman/kardon

Ref. Designator Part Number Description Qty

MAIN PCB (CUP11579W)

CN89 KJP02GA01ZM WAFER WAFER 1 EA CN91 KJP03GA89ZM WAFER WAFER 1 EA CN94 KJP13GA98ZM WAFER WAFER 1 EA CN95 KJP08GA98ZM WAFER WIRE 1 EA ET01 CMD1A387 BRACKET , PCB BRACKET 3 EA ET01 CNE75 PLATE , EARTH PLATE 1 EA ET02 CMD1A387 BRACKET , PCB BRACKET 3 EA ET03 CNE75 PLATE , EARTH PLATE 1 EA JK91 CJJ5R006Z TERMINAL , SPEAKER SPEAKER TERMINAL 1 EA JK92 CJJ5Q012Z TERMINAL , SPEAKER SPEAKER TERMINAL 1 EA JK97 CJJ4P041W JACK IN/OUT JACK 1 EA JK98 CJJ4P042W JACK IN/OUT JACK 1 EA JW90 CWEE212120VV WIRE ASS'Y WIRE 1 EA JW91 CWE8212180VV WIRE ASS'Y WIRE 1 EA JW99 CWE8202150AA WIRE ASS'Y WIRE 1 EA L501 CLEY0R5KAK COIL , SPEAKER 0.5UH K 1 EA L502 CLEY0R5KAK COIL , SPEAKER 0.5UH K 1 EA L503 CLEY0R5KAK COIL , SPEAKER 0.5UH K 1 EA L504 CLEY0R5KAK COIL , SPEAKER 0.5UH K 1 EA L505 CLEY0R5KAK COIL , SPEAKER 0.5UH K 1 EA L506 CLEY0R5KAK COIL , SPEAKER 0.5UH K 1 EA L507 CLEY0R5KAK COIL , SPEAKER 0.5UH K 1 EA RY94 HSL1A008ZE RELAY SDT-S-112DMR 1 EA TH91 KRTP42T7D330B THERMAL SENSOR , POSISTOR POSISTOR 1 EA T902 CLT5J033ZU TRANS , SUB SUB TRANS 1 EA

CTW3+8J SCREW SCREW 2 EA

CNVM9011MS071L AVR 240 TUNER MODULE

Page 71

CAM350󰼿PRO󰼿V󰼿7.6󰼿:󰼿Mon󰼿Sep󰼿01󰼿10:29:56󰼿2003󰼿-󰼿(Untitled)

MAIN BOARD 1 (AMP)

AVR240 harman/kardon

Page 72

AVR240 harman/kardon

Page 73

AVR240 harman/kardon

Page 74

AVR240 harman/kardon

Page 75

AVR240 harman/kardon

Page 76

AVR240 harman/kardon

Page 77

AVR240 harman/kardon

74ACT04SC : IC52,75,83,84

74AC04 • 74ACT04 Hex Inverter

November 1988 Revised November 1999

74AC04 • 74ACT04 Hex Inverter

General Description

The AC/ACT04 contains six inverters.

Features

■ ICC reduced by 50% on 74AC only

■ Outputs source/sink 24 mA

■ ACT04 has TTL-compatible inputs

Ordering Code:

Order Number Package Number Package Description

74AC04SC M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body 74AC04SJ M14D 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 74AC04MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 74AC04PC N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide 74ACT04SC M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body 74ACT04MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 74ACT04PC N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide

Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code. (PC not available in Tape and Reel.)

Logic Symbol

IEEE/IEC

Connection Diagram

Pin Descriptions

Pin Names Description

FACT is a trademark of Fairchild Semiconductor Corporation.

Inputs Outputs

Page 78

AVR240 harman/kardon

M54HCU04 M74HCU04

HEX INVERTER (SINGLE STAGE)

.HIGH SPEED

tPD= 5 ns (TYP.) AT VCC=5V

.LOWPOWER DISSIPATION

ICC=1 µA(MAX.) AT TA=25°C

.HIGH NOISEIMMUNITY

NIH=VNIL

.OUTPUT DRIVECAPABILITY

10 LSTTL LOADS

=10%VCC(MIN.)

B1R

(PlasticPackage)

F1R

(CeramicPackage)

.SYMMETRICAL OUTPUT IMPEDANCE

IOH=IOL=4 mA(MIN.)

.BALANCEDPROPAGATIONDELAYS

PLH=tPHL

.WIDE OPERATING VOLTAGERANGE

VCC(OPR)= 2 V TO 6 V

.PIN AND FUNCTION COMPATIBLE WITH

54/74LS04

M1R

(MicroPackage)

ORDER CODES :

M54HC U04F1R M74H CU04M1R M74HC U04B1R M74HCU04C1R

C1R

(Chip Carrier)

DESCRIPTION

The M54/74HCU04 is ahighspeed CMOS HEXINVERTER (SINGLE STAGE) fabricated in silicon gate C2MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low power consumption.

As the intrnal circuit is composed of a single stage inverter, it can be used in crystaloscillator.

All inputs are equipped with circuits against static discharge and transient excess voltage.

INPUT AND OUTPUT EQUIVALENT CIRCUIT

PIN CONNECTIONS(top view)

NC = No Internal Connection

January 1993

1/9

Page 79

AVR240 harman/kardon

PIN ASSIGNMENT (74HCU04AFN : IC71,72,76 )

1A 1Y 2A 2Y 3A 3Y

2 3 4 5 6

14 13 12 11 10 9

Vcc

6A 6Y 5A 5Y 4A

LOGIC SYMBOL

GND

1A 2A 3A

4A 5A 6A

(1) (3) (5) (9)

(11)

(13)

(2) (4) (6) (8)

(10) (12)

1Y 2Y 3Y

4Y 5Y 6Y

TRUTH TABLE

A L

Y H

Page 80

AVR240 harman/kardon

MITSUMI

Video Switch · 75Ω driver · Y/C mix MM1501

Video Switch · 75Ω driver · Y/C mix

Monolithic IC MM1501 Series

Outline

This IC extends the series of ICs for video/audio signal switching, with a 2-input 1-output single video switch,

video signal/chroma signal 75Ω driver, and Y/C mixing circuit in one small package (SOT-26).

Features

(1) Low power consumption achieved. (2) Low power supply voltage realized.

(3) Frequency bandwidth without 75Ω driver: 10MHz with 75Ω driver: 7MHz

(4) Cross talk 70dB When 4.43MHz

(5) With SAG measures pin (75Ω driver and Y/C mix driver)

Package

SOT-26A (with 75Ω driver) SOT-26B (without 75Ω driver)

Applications

(1) TV (2) VTR (3) Video camera (4) Digital still camera (5) Other visual equipment

Line-up

Functions

Switch

Driver

Y/C mix

Model Name

MM1501 4.5~13.0V MM1502 4.5~13.0V MM1503 4.5~13.0V MM1504 MM1505 4.5~13.0V MM1506 4.5~13.0V MM1507 4.5~13.0V MM1508 4.5~13.0V MM1509 MM1510 4.5~13.0V MM1511 MM1512 / 4.5~13.0V

Input

Output

Clamp 6dB amp 75Ω driver

/ 4.5~13.0V

SAG measures pin

Power supply

voltage

4.5~13.0V

Page 81

AVR240 harman/kardon

MITSUMI

MM1507 MM1508

Video Switch · 75Ω driver · Y/C mix MM1501

MM1509 MM1510

MM1511 MM1512

Page 82

AVR240 harman/kardon

MITSUMI

Video Switch · 75Ω driver · Y/C mix MM1501

MM1509

Item Symbol Measurement conditions Min. Typ. Max. Unit

Consumption current I

Current consumption for PS I

PS input voltage L V

PS input voltage H V

Input pin voltage V

Output pin voltage V

Voltage gain G

Frequency characteristic fc Refer to measurement procedures

Differential gain V

Differential phase V

CC=9V DG Refer to measurement procedures CC=9V DP Refer to measurement procedures

Output dynamic range V

CC1 Refer to measurement procedures 6.3 8.2 mA CC2 Refer to measurement procedures 20 30 µA

PSL Refer to measurement procedures 0.3 V PSH Refer to measurement procedures 1.8 V

IN No-signal, no-load 1.75 1.95 2.15 V

OUT No-signal, no-load 2.35 V

V Refer to measurement procedures 5.5 6.0 6.5 dB

10+1dB

30+3%

3 0 +3 deg

D Refer to measurement procedures 2.9 3.2 V

Input impedance Zi 15 kΩ

MM1510

Item Symbol Measurement conditions Min. Typ. Max. Unit

Consumption current I

Current consumption for PS I

PS input voltage L V

PS input voltage H V

Input pin voltage V

Output pin voltage V

Voltage gain G

Frequency characteristic fc Refer to measurement procedures

Differential gain DG Refer to measurement procedures

Differential phase DP Refer to measurement procedures

Output dynamic range V

CC1 Refer to measurement procedures 6.4 8.3 mA CC2 Refer to measurement procedures 20 30 µA

PSL Refer to measurement procedures 0.3 V PSH Refer to measurement procedures 1.8 V

IN No-signal, no-load 1.15 1.35 1.55 V

OUT

V Refer to measurement procedures 5.5 6.0 6.5 dB

D Refer to measurement procedures 2.6 3.0 V

No-signal, no-load 1.15 V

10+1dB

30+3%

3 0 +3 deg

MM1511

Item Symbol Measurement conditions Min. Typ. Max. Unit

Consumption current I

Y input pin voltage V

C input pin voltage V

Output pin voltage V

Voltage gain G

Frequency characteristic fc Refer to measurement procedures

Differential gain DG Refer to measurement procedures

Differential phase DP Refer to measurement procedures

Y output dynamic range V

C output dynamic range V

C input impedance Zi 15 kΩ

Output impedance Zo 25 Ω

CC Refer to measurement procedures 4.4 5.7 mA YIN No-signal, no-load 2.00 2.20 2.40 V CIN No-signal, no-load 1.85 2.05 2.25 V

OUT No-signal, no-load 1.15 V

V Refer to measurement procedures

DY Refer to measurement procedures 2.6 2.9 V DC Refer to measurement procedures 2.0 V

0.5 0 6.5 dB

1 0 +0.5 dB

30+3%

3 0 +3 deg

Page 83

AVR240 harman/kardon

HY57V161610ETP-I

2 Banks x 512K x 16 Bit Synchronous DRAM

DESCRIPTION

THE Hynix HY57V161610E is a 16,777,216-bits CMOS Synchronous DRAM, ideally suited for the main memory and graphic applications which require large memory density and high bandwidth. HY57V161610E is organized as 2banks of 524,288x16.

HY57V161610E is offering fully synchronous operation referenced to a positive edge clock. All inputs and outputs are synchronized with the rising edge of the clock input. The data paths are internally pipelined to achieve very high bandwidth. All input and output voltage levels are compatible with LVTTL.

Programmable options include the length of pipeline (Read latency of 1,2 or 3), the number of consecutive read or write cycles initiated by a single control command (Burst length of 1,2,4,8 or full page), and the burst count sequence(sequential or interleave). A burst of read or write cycles in progress can be terminated by a burst terminate command or can be interrupted and replaced by a new burst read or write command on any cycle. (This pipeline design is not restricted by a `2N` rule.)

FEATURES

• Single 3.0V to 3.6V power supply

• All device pins are compatible with LVTTL interface

• JEDEC standard 400mil 50pin TSOP-II with 0.8mm of pin pitch

• All inputs and outputs referenced to positive edge of system clock

• Data mask function by UDQM/LDQM

• Internal two banks operation

ORDERING INFORMATION

Part No. Clock Frequency Organization Interface Package

HY57V161610ETP-5I 200MHz

HY57V161610ETP-55I 183MHz

HY57V161610ETP-6I 166MHz

HY57V161610ETP-7I 143MHz

HY57V161610ETP-8I 125MHz

• Auto refresh and self refresh

• 4096 refresh cycles / 64ms

• Programmable Burst Length and Burst Type

- 1, 2, 4, 8 and Full Page for Sequence Burst

- 1, 2, 4 and 8 for Interleave Burst

• Programmable CAS Latency ; 1, 2, 3 Clocks

• Pb-free Package

2Banks x 512Kbits x 16 LVTTL

400mil

50pin TSOP II

(Pb free)

HY57V161610ETP-10I 100MHz

HY57V161610ETP-15I 66MHz

Note :

1. VDD(min) of HY57V161610ETP-5I/55I is 3.15V

2. Hynix supports lead free part for each speed grade with same specification.

This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any responsibility for use of circuits described. No patent licenses are implied

Rev. 0.1 / Nov. 2003 1

Page 84

AVR240 harman/kardon

HY57V161610ETP-I

PIN CONFIGURATION

DQ0

DQ1

SSQ

DQ2

DQ3

DDQ

DQ4

DQ5

SSQ

DQ6

DQ7

VDDQ

LDQM

/WE

/CAS

/RAS

/CS

A11

A10

50pin TSOP II

400mil x 825mil

0.8mm pin pitch

DQ15

DQ14

VSSQ

DQ13

DQ12

VDDQ

DQ11

DQ10

VSSQ

DQ9

DQ8

VDDQ

UDQM

CLK

CKE

VSS

PIN DESCRIPTION

PIN PIN NAME DESCRIPTION

CLK Clock

CKE Clock Enable

CS BA Bank Address Select either one of banks during both RAS

A0 ~ A10 Address

, CAS, WE

RAS

LDQM, UDQM Data Input/Output Mask DQM control output buffer in read mode and mask input data in write mode DQ0 ~ DQ15 Data Input/Output Multiplexed data input / output pin

DD/VSS Power Supply/Ground Power supply for internal circuit and input buffer

DDQ/VSSQ Data Output Power/Ground Power supply for DQ

V NC No Connection No connection

Chip Select Command input enable or mask except CLK, CKE and DQM

Row Address Strobe, Column Address Strobe, Write Enable

The system clock input. All other inputs are referenced to the SDRAM on the rising edge of CLK.

Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh.

and CAS activity.

Row Address : RA0 ~ RA10, Column Address : CA0 ~ CA7 Auto-precharge flag : A10

, CAS and WE define the operation.

RAS Refer function truth table for details

Rev. 0.1 / Nov. 2003 2

Page 85

AVR240 harman/kardon

HY57V161610ETP-I

FUNCTIONAL BLOCK DIAGRAM

1Mx16 Synchronous DRAM

Self Refresh Counter

Refresh

Interval Timer

Address[0:10]

CLK

CKE

BA(A11)

RAS

CAS

UDQM

LDQM

Column Active

State Machine

Auto/Self Refresh

Precharge Row Active

Refresh

Counter

Ref. Addr.[0:11]

Address Register

Burst Length

Counter

Row Decoder

Row Addr. Latch/Predecoder

Overflow

512Kx16

Bank 0

Sense AMP & I/O gates

Column Decoder

Column Addr.

Latch & Counter

Column Decoder

Sense AMP & I/O gates

Data Input/Output Buffers

DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15

512Kx16

Bank 1

Row Addr. Latch/Predecoder

I/O ControlTest ModeMode Register

Rev. 0.1 / Nov. 2003 3

Page 86

AVR240 harman/kardon

HY57V161610ETP-I

COMMAND TRUTH TABLE

Command CKEn-1 CKEn CS RAS CAS WE DQM A0~A9

Mode Register Set H X LLLLX OP code

No Operation H X

Bank Active H X L L H H X Row Address V

Read

Read with Auto precharge H

Write

Write with Auto precharge H

Precharge All Bank

Precharge selected Bank LV

Burst Stop H X L H H L X X

U/LDQM H X V X

Auto Refresh H H L L L H X X

Burst-READ-Single-WRITE H XLLLLX

Entry H L LLLHX

Self Refresh

Precharge power down

Exit L H

Entry H L

Exit L H

H X LHLHX

HXLHLLX

HXLLHLXX

HXXX

LHHH

HXXX

LHHH

HXXX

LHHH

HXXX

LHHH

Column

Address

Column

Address

A10/

A9 Pin High

(Other Pins OP code)

BA Note

Clock Suspend

Entry H L

Exit L H X X

HXXX

XLVVV

Note :

1. Exiting Self Refresh occurs by asynchronously bringing CKE from low to high.

2. X=Do not care, L=Low, H=High, BA=Bank Address, RA= Row Address, CA=Column Address, Opcode=Operand Code,

NOP=No Operation.

Rev. 0.1 / Nov. 2003 12

Page 87

AVR240 harman/kardon

74LCX32 Low Voltage Quad 2-Input OR Gate with 5V Tolerant Inputs

March 1995 Revised February 2005

74LCX32 Low Voltage Quad 2-Input OR Gate

with 5V Tolerant Inputs

General Description

The LCX32 contains four 2 -input O R ga tes. The i nputs tolerate voltages up to 7V allo wing the interface of 5V systems to 3V systems.

The 74LCX32 is fabrica ted with advance d CMOS technology to achieve high speed operation while maintaining CMOS low power dissipation.

Features

■ 5V tolerant inputs

■ 2.3V–3.6V V

■ 5.5 ns t

■ Power down high impedance inputs and outputs

■

24 mA output drive (VCC 3.0V)

■ Implements patented noise/EMI reduction circuitry

■ Latch-up performance exceeds JEDEC 78 conditions

■ ESD performance:

Human body model Machine model ! 150V

■ Leadless Pb-Free DQFN package

specifications provided

max (VCC 3.3V), 10 PA ICC max

2000V

Ordering Code:

Order Number

74LCX32M M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow 74LCX32MX_NL

(Note 2) 74LCX32SJ M14D Pb-Free 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 74LCX32BQX

(Note 1) 74LCX32MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 74LCX32MTCX_NL

(Note 2)

Devices also availab le in Tape and Reel. Specify by appending the suffix let t er “X” to the ordering code . Pb-Free package per JEDEC J-STD-020B.

Note 1: DQFN package available in Tape and Reel only. Note 2: “_NL” indicates Pb-Free pac k age (per JEDEC J-ST D -020B). Device availa ble in Tape and Reel only.

Package Number

M14A Pb-Free 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow

MLP014A Pb-Free 14-Terminal Depopulated Quad Very-Thin Flat Pack No Leads (DQFN), JEDEC

MO-241, 2.5 x 3.0mm

MTC14 Pb-Free 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm

Wide

Package Description

Page 88

AVR240 harman/kardon

Logic Symbol

74LCX32

Pin Descriptions

Pin Names Description

, B

IEEC/IEC

Inputs

Outputs

Connection Diagrams

Pin Assignments for SOIC, SOP, and TSSOP

Pad Assignment for DQFN

(Top View)

Page 89

AVR240 harman/kardon

ASAHI KASEI [AK4589]

2/8-Channel Audio CODEC wi t h DIR

AK4589

GENERAL DE SCRIPTION

The AK4589 is a single chip CODEC that includes two channels of ADC and eight channels of DAC. The ADC outputs 24bit data and the DAC accepts up to 24bit input data. The ADC has the Enhanced Dual Bit architecture with wide dynamic range. The DAC introduces the new developed Advanced Multi-Bit architecture, and achieves wider dynamic range and lower outband noise. The AK4589 has a dynamic range of 102dB for ADC, 114dB for DAC and is well suited for digital surround for home theater audio. The AK4589 also has the balance volume control corresponding to the Dolby Digital (AC-3) system.

The also has digital audio receiver (DIR) and transmitter (DIT) compatible with 192kHz, 24bits. The DIR has 8-channel input selector and can automatically detect a Non-PCM bit stream. The AK4589 provides a compatibility of hardware and software with the AK4588.

*Dolby Digital (AC-3) is a trademark of Dolby Laboratories.

FEATURES



ADC/DAC part

• 2ch 24bit ADC

- 64x Oversampling

- Sampling Rate up to 96kHz

- Linear Phase Digital Anti-Alias Filter

- Sing le-End e d Input

- S/(N+D): 92dB

- Dynamic Range, S/N: 102dB

- Digital HPF for offset cancellation

- Overflow flag

•

8ch 24bit DAC

- 128x Oversampling

- Sampling Rate up to 192kHz

- 24bit 8 times Digi ta l Fi l ter

- Differential Outputs

- On-chip Switched-Capacitor Filter

- S/(N+D): 94dB

- Dynamic Range, S/N: 114dB

- Individual channel digita l volume with 128 levels and 0.5d B step

- Soft mute

- De-emphasis for 32kHz, 44.1kHz, 48kHz

- Zero Detect Function

• High Jitter Tolerance

• Extenal Master Clock Input:

- 256fs, 384fs, 512fs (fs=32kHz ∼ 48kHz)

- 128fs, 192fs, 256fs (fs=64kHz ∼ 96kHz)

- 128fs (fs=120kHz ∼ 192kHz)

MS0339-E-00 2004/09

Page 90

AVR240 harman/kardon

ASAHI KASEI [AK4589]

 DIR/DIT Part

•

AES3, IEC60958, S/PDI F, EIAJ CP1201 Compatible

•

Low jitter Analog PLL

• PLL Lock Range : 32kHz to 192kHz

•

Clock So urce: PLL or X'tal

•

8-channel Receiver input

•

2-channel Transmission output (Through output or DIT)

•

Auxiliary digital input

• De-emphasis for 32kHz, 44 .1 kHz, 48kHz and 96kHz

•

Detection Functions

- Non-PCM Bi t S tream Detection

- DTS-CD Bit Stream Detection

- Sampling Frequency Detection (32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz)

- Unlock & Parity Error Detection

- Validity Flag Detection

•

Up to 24bit Audio Data Format

•

Audio I/F: Master or Slave Mode

• 40-b it C h a nnel Status Buff er

•

Burst Prea mble bit Pc and Pd Buffer for Non -PCM bit stre am

•

Q-subcode Buffer for CD bit stream

•

Serial µP I/F

• T w o M aster Clock Outputs: 64fs/128fs/256fs/512fs

 TTL Level Digital I/F  4-wire Serial and I  Operating Voltage: 4.75 to 5.25V with 5V tolerance  Power Supply for output buffer: 2.7 to 5.25V  80pin LQFP Package (0. 5 mm pitch)  AK4588 compatible w/o analog outputs

C Bus µP I/F for mode setting

MS0339-E-00 2004/09

Page 91

AVR240 harman/kardon

ASAHI KASEI [AK4589]

 Block Diagram

RPVDDPVSS

XTOXTI

RX0 RX1 RX2 RX3

RX4 RX5 RX6 RX7

TX0

TX1

AVDD AVSS

DVDD DVSS TVDD

VIN

B,C,U,

VOUT

LIN

RIN

8 to 3

Input

Selecto

DIT

ADC

Cloc

Recovery

DAIF

Decode

HPF

AC-3/MPEG

Detect

Audio

I/F

DEM

X'tal Oscillato

Error &

STATUS

Detect

Q-subcode

buffe

Clock

Generator

Audio

I/F

µP I/F

MCKO1

MCKO2

LRCK2 BICK2 SDTO2

DAUX2 PDN

I2C

CSN CCLK CDTO CDTI

INT0

INT1

LOUT1+

LOUT1-

ROUT1+

ROUT1-

LOUT2+

LOUT2-

ROUT2+

ROUT2-

LOUT3+

LOUT3-

ROUT3+

ROUT3-

LOUT4+

LOUT4-

ROUT4+

ROUT4-

SCF

DAC

DATT

DEM

DATT

DEM

DATT

DEM

DATT

DEM

DATT

DEM

DATT

DEM

DATT

DEM

DATT

DEM

MCLK LRCK

BICK

SDOUT

SDIN1 SDIN2 SDIN3

SDIN4

MCLK

LRCK1 BICK1

DAUX1

Format

Converter

SDTO1

SDTI1 SDTI2 SDTI3

SDTI4

MS0339-E-00 2004/09

Page 92

AVR240 harman/kardon

ASAHI KASEI [AK4589]

 Ordering Guide

AK4589VQ -10 ∼ +70°C 80pin LQFP(0.5mm pitch) AKD4589 Evaluation Board for AK4589

 Pin Layout

INT0

TX1

TX0

MCLK

VIN

DAUX2

I2C

RX7

CAD1

RX6

CAD0

RX5

TEST2

RX4

INT1 BOUT TVDD

DVDD

DVSS

XT O

XT I

TEST3 MCKO2 MCKO1

COUT UO UT

VOUT

SDTO2

BICK2

LRCK2

SDTO1

BICK1

LRCK1

CDTO

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

PVDD R PVSS

(Top View)

RX3

RX2

60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

TEST1 RX1 NC RX0 AVSS AVDD VREFH VCOM RIN LIN ROUT1+ ROUT1LOUT1+ LOUT1ROUT2+ ROUT2LOUT2+ LOUT2ROUT3+ ROUT3-

CSN

SDTI4

SDTI3

DAUX1

CDTI/SD

CCLK/SCL

SDTI2

SDTI1

XTL1

PDN

XTL0

DZF2

MASTE

DZF1

LOUT4

LOUT3

ROUT4

LOUT3

ROUT4

MS0339-E-00 2004/09

Page 93

AVR240 harman/kardon

ASAHI KASEI [AK4589]

PIN/FUNCTION

No. Pin Name I/O Function

1 INT1 O Interrupt 1 Pin

BOUT O

2 3 TVDD 4 DVDD 5 DVSS - Digital Ground Pin 6 XTO O X'tal Output Pin 7 XTI I X'tal Input Pin

8 TEST3 I

9 MCKO2 O Master Clock Output 2 Pin 10 MCKO1 O Master Clock Output 1 Pin 11 COUT O C-bit Output Pi n for Receiver Input 12 UOU T O U-bit Output Pin for Receiver Input 13 VOUT O V-bit Output Pin for Receiver Input 14 SD TO2 O Audio Serial Data Output Pin (DIR/DIT part) 15 BICK2 I/O Audio Serial Data Clock Pin (DIR/DIT part) 16 LRCK2 I/O Channel Cl ock Pin ( DIR/ D IT part ) 17 SDTO1 O Audio Serial Data Output Pin (ADC/DAC part) 18 BICK1 I/O Audio Serial Data Clock Pi n (ADC/DAC part) 19 LRCK1 I/O Input Channel Clock Pin 20 CDTO O Control Data Output Pin in Serial Mode, I2C= “ L”.

CCLK I Control Data Clock Pin in Serial Mode, I2C= “L”

SCL I Control Data Clock Pin in Serial Mode, I2C= “H” CDTI I Control Data Input Pin in Serial Mode, I2C= “L”.

SDA I/O Control Data Pin in Serial Mode, I2C= “H”. 23 CSN 24 DAUX 1 I AU X Audi o Serial Dat a Input Pin (ADC/ DAC part)

25 SDTI4 I DAC4 Audio Serial Data Input Pin 26 SDTI3 I DAC3 Audio Serial Data Input Pin 27 SDTI2 I DAC2 Audio Serial Data Input Pin 28 SDTI1 I DAC1 Audio Serial Data Input Pin 29 XTL1 I X’tal Frequency Select 0 Pin 30 XTL0 I X’tal Frequency Select 1 Pin

Block-Start Output Pin for Receiver Input

“H” during first 40 flames. Output Buffer Power Supply Pin, 2.7V∼5.25V Digital Power Supply Pin, 4.75V∼5.25V

Test 3 Pin

This pin should be connected to DVSS.

I Ch ip Select Pin in Serial Mode, I2C= “L”. I This pin should be connected to DVSS, I2C= “H”.

MS0339-E-00 2004/09

Page 94

AVR240 harman/kardon

ASAHI KASEI [AK4589]

No. Pin Name I/O Function

Power-Down Mode Pin

31 PDN I

32 MASTER I

DZF2 O

OVF O

34 DZF1 O

35 LOUT4- O DAC4 Lch Negative Analog Output Pin 36 LOUT4+ O DAC4 Lch Positive Analog Output Pin 37 ROUT4- O DAC4 Rch Negative Analog Ou tput Pin 38 ROUT4+ O DA C4 Rch Positive Analog Output Pin 39 LOUT3- O DAC3 Lch Negative Analog Output Pin 40 LOUT3+ O DAC3 Lch Positive Analog Output Pin 41 ROUT3- O DAC3 Rch Negative Analog Ou tput Pin 42 ROUT3+ O DA C3 Rch Positive Analog Output Pin 43 LOUT2- O DAC2 Lch Negative Analog Output Pin 44 LOUT2+ O DAC2 Lch Positive Analog Output Pin 45 ROUT2- O DAC2 Rch Negative Analog Ou tput Pin 46 ROUT2+ O DA C2 Rch Positive Analog Output Pin 47 LOUT1- O DAC1 Lch Negative Analog Output Pin 48 LOUT1+ O DAC1 Lch Positive Analog Output Pin 49 ROUT1- O DAC1 Rch Negative Analog Ou tput Pin 50 ROUT1+ O DA C1 Rch Positive Analog Output Pin 51 LIN I Lc h An alo g In put Pi n

52 RIN I Rch Anal og Inpu t Pin 53 VCOM 54 VREFH -

When “L”, the AK4589 is powered-down, all digital output pins go “L”, all registers are reset. When CAD1/0 pins are changed, the AK4589 should be reset by PDN pin.

Master Mode Sel ect Pin

“H”: Master mode, “L”: Slave mode

Zero Input Detect 2 Pin (Table 13)

When the input data of the group 1 follow total 8192 LRCK cycles with “0” input data, this pin goes to “H”. And when RSTN bit is “0”, PWDAN bit is “0”, this pin goes to “ H”. It always is in “L” when P/S pin is “H”.

Analog Input Overflow Detect Pin

This pin goes to “H” if the analog input o f Lch or Rch overflows.

Zero Input Detect 1 Pin (Table 13)

When the input data of the group 1 follow total 8192 LRCK cycles with “0” input data, this pin goes to “H”. And when RSTN bit is “0”, PWDAN bit is “0”, this pin goes to “H”. Output is selected by setting DZFE pin when P/S pin is “H”.

470pF capacitor should be connected between LOUT4 - and LOU T4+. 470pF capacitor should be connected between ROUT4- and ROUT4+.

470pF capacitor should be connected between LOUT3 - and LOU T3+.

470pF capacitor should be connected between ROUT3- and ROUT3+.

470pF capacitor should be connected between LOUT2 - and LOU T2+.

470pF capacitor should be connected between ROUT2- and ROUT2+.

470pF capacitor should be connected between LOUT1 - and LOU T1+.

470pF capacitor should be connected between ROUT1- and ROUT1+.

Common Voltage Output Pin

2.2µF capaci tor should be connected to AVSS externally.

Positive Volt ag e Referenc e Input Pin, AVDD

MS0339-E-00 2004/09

Page 95

AVR240 harman/kardon

ASAHI KASEI [AK4589]

No. Pin Name I/O Function

55 AVDD - Analog Power Supply Pin, 4.75V∼5.25V 56 AVSS 57 RX0 I Receiver Channel 0 Pin (Internal biased pin. Internall y bias ed at PVDD/2)

58 NC 59 RX1 I Receiver Channel 1 Pin (Internal biased pin. Internall y bias ed at PVDD/2) 60 TEST1 I 61 RX2 I Receiver Channel 2 Pin (Internal biased pin. Internall y bias ed at PVDD/2) 62 NC 63 RX3 I Receiver Channel 3 Pin (Internal biased pin. Internall y bias ed at PVDD/2)

64 PVSS - PLL Ground pin 65 R 66 PVDD -

67 RX4 I Receiver Channel 4 Pin (Internal biased pin. Internall y bias ed at PVDD/2) 68 TEST2 I 69 RX5 I Receiver Channel 5 Pin (Internal biased pin. Internall y bias ed at PVDD/2)

70 CAD0 I 71 RX6 I Receiver Channel 6 Pin (Internal biased pin. Internall y bias ed at PVDD/2) 72 CAD1 I 73 RX7 I Receiver Channel 7 Pin (Internal biased pin. Internall y bias ed at PVDD/2)

74 I2C I 75 DAUX2 I Auxiliary Audio Data Input Pin (DIR/DIT part)

76 VIN I V-bit Input Pin for Transmitter Output 77 MCLK I 78 TX0 O Transmit Channel (Through Data) Output 0 Pin

79 TX1 O

80 INT0 O Interrupt 0 Pin

Note: All input pins except internal biased pins and Analog input pins (RX0-7, LIN, RIN) should not be l eft floating.

Analog Gr ou nd Pi n , 0V

No Connect pin

No inte rn al bondi ng. Thi s pin sh oul d be conn e ct ed to PVSS.

Test 1 Pin

This pin should be c onnected to PVSS.

No Connect pin

No inte rn al bondi ng. Thi s pin sh oul d be conn e ct ed to PVSS.

External Resistor Pin

12kΩ +/-1% resistor should be connected to PVSS externally.

PLL Power supply Pin, 4.75V∼5.25V

Test 2 Pin

This pin shou ld be conn e cte d to PVS S.

Chip Address 0 Pin (ADC/DAC part)

Chip Address 1 Pin (ADC/DAC part)

Control Mode Select Pin.

“L”: 4-wire Serial , “H”: I

Master Clock Input Pin

Transmit Channel Output1 pin

When DIT bit = “0”, Through Data. When DIT bit = “1”, DAUX2 Data.

PVDD

C Bus

RX pin

20k(typ)

PVSS

Internal biased pin Circuit

VCOM

 Handling of U nused P in

The unused I/O pins should be processed appropriately as below.

Classification Pin Name Setting Analog RX0-7, LOUT1-4, ROUT1-4, LIN, RIN These pins should be open.

INT0-1, BO UT, XTO, MCKO1-2, COUT, UOUT,

Digital

VOUT, SDTO1-2, C D TO, D ZF 1 -2, TX1 -0 CSN, DAUX1-2, SD TI1-4, XTL0-1 TEST1-3 These pins should be connected to PVSS.

These pin s shou l d be open.

These pins should be c onnected to D VSS.

Page 96

AVR240 harman/kardon

CS49400 Family DSP

Multi-Standard Audio Decoder

Features



CS49300 Legacy Audio Decoder Support



Dolby Digital EXTM, Dolby Pro Logic II



DTS-ES 96/24TM, DTS 96/24TM,DTS-ES Discrete 6.1TM, DTS-ES Matrix 6.1TM,DTS Digital Surround



MPEG-2: AAC Multichannel 5.1



MPEG Multichannel and Musicam



MPEG-1/2, Layer III (MP3)



DTS Neo:6TM, LOGIC7®, SRS Circle Surround II



Cirrus Extra SurroundTM, Cirrus Original Surround 6.1 (C.O.S. 6.1)



THX Surround EXTM, THX Ultra2 Cinema



12-Channel Serial Audio Inputs



Integrated 8K Byte Input Buffer



Powerful 32-bit Audio DSP



Customer Software Security Keys



Large On-chip X,Y, and Program RAM



Supports SDRAM, SRAM, FLASH memories



16-channel PCM output



Dual S/PDIF Transmitters



SPI Serial, and Motorola®and Intel®Parallel

Host Control Interfaces



GPIO support for all common sub-circuits

and DTS Virtual 5.1

Description

The CS49400 Audio Decoder DSP is targeted as a marketspecific consumer entertainment processor for AV Receivers and DVD Audio/Video Players. The device is constructed using an enhanced version of the CS49300 Family DSP audio decoder followed by a 32-bit programmable post-processor DSP, which gives the designer the ability to add product differentiation through the Cirrus Framework structure and Framework module library. Dolby Digital Pro Logic II, DTS Digital Surround, MPEG Multichannel, and Cirrus Original Surround 6.1 PCM Effects Processor (capable of generating such DSP audio modes as: Hall, Theater, Church) are included in the cost of the CS49400 Family DSP. Additional algorithms available through the Crystal Ware Licensing Program, give the designer the ability to further

deliver end-product differentiation.

The CS49400 contains sufficient on-chip SRAM to support decoding all major audio decoding algorithms available today including: AAC Multichannel, DTS 96/24, DTS-ES 96/24. The CS49400 also supports a glueless SDRAM/SRAM for increased all-channel delays. The SRAM interface also supports connection to an external byte-wide EPROM for code storage or Flash memory thus allowing products to be fieldupgradable as new audio algorithms are developed.

This chip, teamed with Crystal Ware library, Cirrus digital interface products and mixed signal data converters, enables the conception and design of next generation digital entertainment products.

certified decoder

programming

Software

Compressed

Digital

Interface

Digital

Audio

Input

DSP AB

PLL Clock

Manager

Frame Shifter

Input

Buffer

RAM

Multi-Standard

Audio Decoder

Parallel or Serial

Host Interface

This document contains information for a new product. Cirrus Logic reserves the right to modify this product without notice.

Shared Memory

SAI 0 SAI 1 SAI 2 SAI 3

DSP C

Programmable

32-Bit DSP

DSP

RAM

Serial Audio

Interface

DSP

ROM

External Memory

Digital

Audio

Output

Internal Bus

GPIO and I/O

Parallel or Serial

Host Interface

Interface

DAO 0

DAO 1

Controller

Page 97

AVR240 harman/kardon

2. OVERVIEW

The CS49400 is a 24-bit fixed-point decoder DSP followed by a 32-bit fixed point programmable post-processor DSP. The decoder portion of the CS49400 is referred to as “DSPAB”. The postprocessor DSP is referred to as “DSPC”. Both DSPAB and DSPC include their own dedicated peripherals such as serial and parallel control ports, and serial audio interfaces. DSPC also has a external memory interface which supports SRAM/SDRAM/EPROM.

All the decoding/processing algorithms listed below require delivery of PCM or IEC61937packed compressed data via I2S or LJ formatted digital audio to the CS49400. Today the CS49400 will support all of the following decoding/processing standards:

• PCM Pass-Through/PCM Upsampler

• Dolby Digital™(with Dolby Pro Logic)

• Dolby Digital Pro Logic II

• Dolby Digital EX

™

• Dolby Digital EX Pro Logic II

™

• MPEG-2, Advanced Audio Coding Algorithm

(AAC)

• MPEG Multichannel

• MPEG Multichannel with Dolby Pro Logic II

• MPEG-1/2, Layer III (MP3)

™

• HDCD

All of the above audio decoding/processing algorithms and the associated application notes (AN208 and their corresponding appendices) are available through the Crystal Ware

Software Licensing Program. Please refer to AN208 for the latest listing of application codes for DSPAB.

DSPC is unique to DSPAB in the sense that the designer may choose to just load a standard or enhanced application code (.ULD file) from the Crystal Ware Software Library or if they have access to the Cirrus Framework DSPC Development Kit, they may choose to build their own application code from a variety of modules. A DSPC application code contains all of the necessary post-processing modules, such as Crossbar Mixer, Pro Logic Module, Bass Manager Module, and Audio Manager (Kernel). A module is just a single processing module, such as Tone Control, Parametric/Graphic EQ, or Dolby Pro Logic matrix decoder. DSPC on the CS49400 will support the following post-processing application codes and/or modules:

• Standard Post-Processor (includes the follow-

ing modules all compiled into one .ULD file): Downmixer module, Dualzone module, Crossbar Mixer module, 7.1 Channel Bass Manager module, Audio Manager module (Volume Control, Trim Control and Channel Remap), and Delay module

• DTS Digital Surround™

• DTS 96/24™ (Front-end Decoder)

• DTS Digital Surround™ with Dolby Pro Logic II™

• DTS-ES Extended Surround

™

(DTS-ES Discrete 6.1 and DTS-ES Matrix 6.1)

• DTS-ES 96/24

• DTS Neo:6

• LOGIC7

™

(Front-end Decoder)

™

• SRS Circle Surround™II

• Advanced Post-Processor (includes the all of

the standard post-processing modules plus the Tone Control module, Parametric EQ module, Re-EQ module in all compiled into one .ULD )

• Dolby Pro Logic

• Dolby Pro Logic II

• SRS Circle Surround II

• DTS Neo:6

• LOGIC7

™

• THX®Surround EX™ 7.1 Channel

Post-Processor

Page 98

AVR240 harman/kardon

• THX®Ultra2 Cinema™7.1 Channel Post-Processor

• Cirrus Extra Surround

• Cirrus Original Multichannel Surround

™

• Virtual Dolby Digital™/Virtual Dolby Digital

Pro Logic II

• VMAx VirtualTheater

• HDCD

™

Virtualizer Module

™

Virtualizer Module

Multichannel Decoder

• DVD-Audio/Video and Multichannel SACD Bass Management

™

• DTS/DTS-ES 96/24

THX

Ultra2 Cinema

Back-End Decoder

™

Back-End Decoder with

™

All of the above audio post-processing applications codes and/or Cirrus FrameworkTM modules and the associated application notes (AN209 and the associated appendices) are available through the Crystal WareTM Software Licensing Program. All standard or enhanced post-processing code modules are only available to customers who

qualify for the Cirrus Framework

CS49400 Family DSPC Programming Kit. Please refer to AN209 for the latest listing of application codes and Cirrus FrameworkTM modules available for DSPC.

2.1 DSPAB

2.2 DSPC

DSPC is a 32-bit, general-purpose, fixed-point RAM-based processor which includes on-chip ROM tables. It has been designed with a generous amount of on-chip program and data RAM, and has all necessary peripherals required to support the latest standards in consumer entertainment products such as AV receivers and DVDAudio/Video players.

DSPC has on-chip data and program RAM, and both external SDRAM and SRAM memory interfaces. These interfaces can be used to expand the data memory. DSPC also has its own 8-channel digital audio input for post-processing PCM from a Multichannel Super Audio CD (SACD) input or DVD-Audio/Video input, via high-performance A/Ds or from some other type of multichannel digital input, capable of delivering 4 stereo digital audio channels such as IEEE1394 (a.k.a. I-Link or Firewire®). Data can be delivered to this port using the standard audio formats (I can be controlled serially using the SPI standard or via Parallel host control port using the Motorola or Intel®standard. DSPC has a Digital Audio output port that has eight stereo serial data outputs for a total of 16 channels. Data can be delivered from these outputs in serial I of these outputs (AUDAT3, AUDAT7) can be configured as a IEC60958-format S/PDIF transmitter.

S or LJ). DSPC

S or LJ format. Two

DSPAB is an enhanced version of the CS49300. It was designed to have legacy code support for all decoder applications developed for the CS49300. It includes performance enhancements such as the ability to decode AAC without the need for external SRAM memory. DSPAB has a Digital Audio Input (DAI) and a Compressed Data Input

(CDI) port for data delivery in either I

SorLJ format. DSPAB can be controlled serially using the SPI standard and can also be controlled via a

Parallel host control port using the Motorola

Intel

communication standards.

This document focuses on the electrical features of the CS49400. The features are described from a hardware design perspective. It should be understood that not all of the features portrayed in this document are supported by all of the versions of application code available. The application code user’s guides should be consulted to determine which hardware features are supported by the software.

Please note that a download of application software is required each time the part is powered up. This term should be interpreted as meaning the transfer of application code into the internal memory of the part

Page 99

AVR240 harman/kardon

from either an external microcontroller or through one of the boot procedures listed in Section 8.

3. TYPICAL CONNECTION DIAGRAMS

Four typical connection diagrams have been presented to illustrate using the part with the different communication modes available. They are as follows:

Figure 27, "SPI Control with External Memory 144 Pin Package" on page 38.

Figure 28, "Intel

Parallel Control Mode - 144 Pin

Package" on page 39.

Figure 29, "Motorola

Parallel Control Mode - 144

Pin Package" on page 40.

The following should be noted when viewing the typical connection diagrams:

Note: The pins are grouped functionally in each

of the typical connection diagrams. Please be aware that the CS49400 symbol may appear differently in each diagram.

The external memory interface is supported when a serial or parallel communication mode has been chosen.

3.1 Multiplexed Pins

The CS49400 incorporates a large amount of flexibility into a 144 pin package. The pins are internally multiplexed to serve multiple purposes. Some pins are designed to operate in one mode at power up, and serve a different purpose when the DSP is running. Other pins have functionality which can be controlled by the application running on the DSP. In order to better explain the behavior of the part, the pins which are multiplexed have been given multiple names. Each name is specific to the pin’s operation in a particular mode.

In this document, pins will be referred to by their functionality. Section 12 “Pin Description” on

page 86 describes each pin of the CS49400 and lists

all of its names. Please refer to this section when exact pin numbers are in question.

3.2 Termination Requirements

The CS49400 incorporates open drain pins which must be pulled high for proper operation. FINTREQ

and INTREQ are always open drains

which requires a pull-up for proper operation.

Due to the internal, multiplexed design of the pins, certain signals may or may not require termination depending on the mode being used. If a parallel host communication mode is not being used, all parallel control pins must be terminated or driven as these pins will come up as high impedance inputs and will be prone to oscillation if they are left floating. The specific termination requirements may vary since the state of some of the GPIO pins will determine the communication mode at the rising edge of reset (please see Section 6 “Control”

on page 41 for more information). For the explicit

termination requirements of each communication mode please see the typical connection diagrams.

Generally a 3.3k Ohm resistor is recommended for open drain and mode select pins. A 10k Ohm resistor is sufficient for all other unused inputs.

3.3 Phase Locked Loop Filter

The internal phase locked loop (PLL) of the CS49400 requires an external filter. The topology of this filter is shown in the typical connection diagrams. The component values are shown below. Care should be taken when laying out the filter circuitry to minimize trace lengths and to avoid any high frequency signals. Any noise coupled onto the filter circuit will be directly coupled into the PLL, which could affect performance.

Reference Designator Value

C1 2.2uF

C2 1200pF

C3 68pF

R1 3k Ohm

Table 1. PLL Filter Component Values

Page 100

AVR240 harman/kardon

100

4. POWER

The CS49400 requires a 2.5V digital power supply for the core logic and 2.5V I/O and a 2.5V analog power supply for the internal PLL. For systems with external memory that runs on 3.3V, a 3.3V digital power supply is required on the VDDSD pins along with four digital grounds on VSSSD. There are seven digital power pins, VDD1 through VDD7, along with seven digital grounds, VSS1 through VSS7. There is one analog power pin, PLLVDD, and one analog ground, PLLVSS. The recommendations given below for decoupling and power conditioning of the CS49400 will help to ensure reliable performance.

4.1 Decoupling

It is necessary to decouple the power supply by placing capacitors directly between the power and ground of the CS49400. Each pair of power/ground pins (VDD1/VSS1, etc.) should have its own decoupling capacitors. The recommended procedure is to place both a 0.1uF and a 1uF capacitor as close as physically possible to each power pin. The 0.1uF capacitor should be closest to the part (typically 5mm or closer).

4.2 Analog Power Conditioning

In order to obtain the best performance from the CS49400’s internal PLL, the analog power supply PLLVDD must be as noise-free as possible. A ferrite bead and two capacitors should be used to filter the VDD to generate PLLVDD. This power scheme is shown in the typical connection diagrams.

4.3 Ground

For two layer circuit boards, care should be taken to have sufficient ground between the DSP and parts in which it will be interfacing (DACs, ADCs, S/PDIF Receivers, microcontrollers, and especially external memory). Insufficient ground can degrade noise margins between devices resulting in data integrity problems.

4.4 Pads

The CS49400 has two different I/O voltage levels. All signal pins not associated with the External SRAM/SDRAM memory interface operate from the 2.5V supply and are 3.3V tolerant. The external SRAM/SDRAM memory interface operates at

3.3V only. However, if the external memory interface is not used VDDSD1-4 may be connected to 2.5V.