Haier AS09GS1ERA, AS07GS1ERA, AS12GS1ERA, HUM09HC03-R2, HUM12HC03-R2 Manual

SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL

AS07GS1ERA

AS09GS1ERA

AS12GS1ERA

Contents

PARTS AND FUNCTIONS											2
OPERATION											3
INDOOR UNIT INSTALLAION											5
MAINTENANCE											9
CAUTIONS											10
TROUBLE SHOOTING												11

●Please read this operation manual before using the air conditioner.

Keep this operation manual for future reference.

0010535380

Parts and Functions

		Indoor Unit				Remote controller

18

	2
	3
		4	6
			7
		5
1	Inlet	6	Display board
2	Inlet grille	7	Emergency Switch
3	Outlet	8	Air Purifying Filter
4	Vertical blade		(inside)

(adjust left and right air flow)

5 Horizontal flap

(adjust up and down air flow.

Don't adjust it manually)

Please be subject to the actual produce purchased the above picture is just from your reference

Outdoor Unit

	4
OUTLET	CONNECTING PIPING AND ELECTRICAL WIRING
INLET	DRAIN HOSE

Please be subject to the actual produce purchased the above picture is just from your reference

Clock set

Press CLOCK button, "AM" or "PM" flashes.

Pressorto set correct time. Each press will increase or decrease 1min. If the button is kept pressed,time will change quickly. After time setting is confirmed,press SET,

"AM "and "PM" stop flashing,while clock starts working.

POWER/SOFT

TIMER

CLOCK

LIGHT

SET SLEEP

LOCK RESET

	1	10
		6
	2
		7
	5	8
	3	9
		4
	ON/OFF
	13	11
	FAN
	18
	MODE

	SWING		15
		POWER/SOFT	23
	TIMER
12
			20
21	CLOCK		14
	LIGHT
19			16
	SET	SLEEP
17	LOCK	RESET	22

1. Mode display

Operation mode AUTO COOL DRY HEAT FAN

Remote controller

2.SWING display

3.FAN SPEED display

AUTO LO MED HI

4.SLEEP display

5.LOCK display

6.SIGNAL SENDING

7.TIMER OFF display

8.TIMER ON display

9. CLOCK display 10.TEMP display

11.POWER ON/OFF button

12.MODE button

13.FAN button

14.HOUR button

15.SWING button

16.SLEEP button

17.LOCK button

Used to lock buttons and LCD display.

18.TEMP.SETTIN button

19.SET / LIGHT button

20.TIMER button

21.CLOCK button

Used to set correct time. 22. RESET button

When the remote controller appears abnormal, use a sharp pointed article to press this button to reset the remote controller normal.

23. HOUR / POWER/SOFT button Used to set clock and timer setting. Every time the button is pressed, display changes as follows:

BLANK

POWER SOFT

Loading of the battery

			1Remove the battery cover;
			2 Load the batteries as illustrated.
			2 R-03 batteries, resetting key
			(cylinder);
			3 Be sure that the loading
	4		is in line with the" + "/"-";
		Load the battery,then put on the cover again.

Note:

The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or changeover type fluorescent lamp or wireless telephone is installed in the room, the recei ver is apt to be disturbed in receiving the signals, so the distance to the indoor unit should be shorter.

Full display or unclear display during operation indicates the batteries have been used up.Please change batteries.

If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later.

Hint:

Remove the batteries in case won't be in use for a long period. If there is any display after taking-out, just press reset key.

2

Operation

Base Operation

	Remote controller	ON/OFF
			FAN
			MODE
			SWING
			POWER/SOFT
		TIMER
		CLOCK
		LIGHT
		SET	SLEEP

LOCK RESET

1. Unit start

Press ON/OFF on the remote controller, unit starts.

2.Select operation mode

Press MODE button. For each press, operation mode changes as follows:

Remote controller:

	AUTO	COOL DRY	HEAT	FAN
3.Select temp.setting
Press		button
	Every time the button is pressed, temp.setting
	increase 1oC,if kept depressed, it will increase
	rapidly
	Every time the button is pressed, temp.setting
	decrease 1oC,if kept depressed, it will
	decrease	rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed
changes as follows:
Remote controller:
		AUTO	LO	MED	HI

Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

	Operation	Remote					Note
	Mode	Controller
							Under the mode of auto operation, air conditioner
	AUTO						will automatically select Cool or Heat operation
							according to room temperature When FAN is set
							to AUTO the air conditioner automatically adjusts
							the fan speed according to room temperature.
	COOL
							In DRY mode, when room temperature becomes
	DRY						lower than temp.setting+2o C, unit will run
							intermittently at LOW speed regardless of FAN
							setting.
							In HEAT mode, warm air will blow out after a short
	HEAT						period of the time due to cold-draft prevention function.
							When FAN is set to AUTO, the air conditioner automatically
							adjusts the fan speed according to room temperature.
							In FAN operation mode , the unit will not operate in
	FAN						COOL or HEAT mode but only in FAN mode ,
							AUTO is not available in FAN mode. And temp.
							setting is disabled. In FAN mode, sleep operation
							is not available.

Emergency operation and test operation

Emergency Operation:

Use this operation only when the remote controller is defective or lost, and with function of emergency running, air conditoner can run automatically for a while.

When the emergency operation switch is pressed, the " Pi " sound is heard once, which means the start of this operation. When power switch is turning on for the first time and emergency operation starts, the unit will run automatically in the following modes:

Room	Designated	Timer	Fan	Operation	emergency
temperature	temperature	mode	speed	mode	operation switch

Above 23oC	26oC		AUTO	Pi
		No		COOL
Below 23oC	23oC	No	AUTO	HEAT

It is impossible to change the settings of temp. and fan speed,It is also not possible to operate in timer or dry mode.

Test operation:

Test operation switch is the same as emergency switch.

Use this switch in the test operation when the room temperature is below 16oC, do not use it in the

normal operation.

Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi".

Under this operation mode,the fan motor of indoor unit will run in high speed.

test operation switch

Pi

Pi

Air Flow Direction Adjustment

1.Status display of air flow

Vertical flap

Pos.1 blank Pos.2 Pos.3

Pos.4 (Auto swing)

2.Left and right air flow adjustment(manual)

Move the vertical blade by a knob on air conditioner to adjust left and right direction referring to Fig.

'

Cautions:

When adjusting the flap by hand,turn off the unit. When humidity is high,condensate water might occur at air outlet if all vertical louvers are adjusted to left or right.

It is advisable not to keep horizontal flap at downward position for a long time in COOLor DRY mode , otherwise, condensate water might occur.

Note:

When restart after remote turning off, the remote controller will automatically memorize the previous set swing position.

3

Operation

Sleep Operation

Before going to bed,you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep.

Use of SLEEP function

After the unit starts,set the operation status, then press SLEEP button before which the clock must be adjusted and time being set.

Operation Mode

1. In COOL,DRY mode

1 hours after SLEEP mode starts,temp.will become

1OC higher than temp.setting.After another 1 hours, temp.rises by 1OC futher.The unit will run for further 6 hours then stops Temp. is higher than temp. setting so that room temperature won’t be too low for your sleep.

SLEEP operation starts

SLEEP operation stops

		Approx.6hrs
	1 hr	Rises 1OC
1 hr	Rises 1OC
Temp.setting		Unit stop

In COOL, DRY mode

2. In HEAT mode

1 hours after SLEEP mode starts,temp will become 2OC lower than temp.setting.After another 1 hours,temp decrease by 2OC futher.After more another 3hours,temp.rises by 1OC futher.The unit will run for further 3 hours then stops.Temp.is lower than temp. setting so that room temperature won’t be too high for your sleep.

Temp.setting		Unit stop
1 hr	Decreases 2OC
	1 hr
	Decreases 2OC
		3 hrs
	3 hrs	Rises 1OC
SLEEP		SLEEP
operation starts		operation stops

In HEAT mode

3.In AUTO mode

The unit operaters in corresponding sleep mode adapted to the automatically selected operation mode.

4. In FAN mode

It has no SLEEP function.

5. When quiet sleeping function is set to 8 hours, the quiet sleeping time can not be adjusted. When TIMER function is set , the quiet sleeping function can't be set up. After the sleeping function

is set up, if user resets TIMER function, the sleeping function will be cancelled; the machine will be in the state of timing-on, if the two modes are set up at the same time, either of their operation time is ended first, the unit will stop automatically, and the other mode will be cancelled.

Power Failure Resume Function

1. If the unit is started for the first time, the compressor will not start running unless 3 minutes have elapsed. When the power resumes after power failure, the unit will run automatically, and 3 minutes later the compressor starts running.

2. Note to the power failure resume:

press the sleep button ten times in five seconds and enter this function after hearing four sounds. And press the sleep button ten times within five seconds and leave this function after hearing two sounds.

POWER/SOFT Operation

(1) POWER Operation

When you need rapid heating or cooling, you can use this function. In COOL mode, fan speed automatically takes high speed of AUTO fan mode. In HEAT mode, fan speed automatically takes medium speed of AUTO fan mode.

(2) SOFT Operation

You can use this function when silence is needed for rest or reading. In SOFT operation mode, fan speed automatically takes low speed of AUTO fan mode.

Note

During POWER operation, in rapid HEAT or COOL mode the room will show uniform temperature distribution. Long period

SOFT operation will cause effect of not too cool or not too warm.

To cancel POWER or SOFT operation

Press POWER/SOFT button again, POWER or SOFT disappears.

4