Page 1
WS200 direct connection to NavNet 3D
(NMEA2000 powered through NN3D)
To activate the internal resistor in the
WS200 antenna, insert the supplied
contact pin into socket #5 in the
connector before connecting it to the
antenna.
18 Pin pigtail cable
supplied for use with
Data 2 and 3
000-164-608
NMEA2000 Micro
Double-ended cable
Male – Female
1 meter = 000-167-962
2 meter = 000-167-963
6 meter = 000-167-964
Fem/Fem/Male
“T” Connector
AIR-052-531
This is to supply voltage for
the NMEA2000 Bus. The
minimum voltage is 9 VDC
and the maximum is 16 VDC.
(1 amp MAX load)
1 amp Fuse
(local supply)
NMEA2000
Terminator
Female
AIR-335-792
Pink
Data
Port 2
Pin 17
Light
Green
Data
Port 2
Pin 18
Page 2
WS200 connection to DRS Dome and NavNet 3D
To activate the internal resistor in the
WS200 antenna, insert the supplied
contact pin into socket #5 in the
connector before connecting it to the
antenna.
Cut the NMEA2000 connector off of
WS200 cable and connect the wires to
the green NMEA2000 connector inside
the DRS2D or DRS4D.
Match the wire colors to the colors shown
in the DRS Connector close-up.
Inside DRS2D and DRS4D
DRS Connector
close-up
123456
Ethernet and power
Use the included 3 hole
gasket for this
installation application.
(See below)
Terminator Resistor
120 Ω
000-167-746
(supplied)
Page 3
WS200 connection to DRS Gearbox and NavNet 3D
To activate the internal resistor in the
WS200 antenna, insert the supplied
contact pin into socket #5 in the
connector before connecting it to the
antenna.
Cut the NMEA2000 connector off of cable
and connect the wires to the gray
NMEA2000 terminal inside the DRS
Gearbox.
Match the wire colors to the colors shown
in the DRS Connector close-up.
Use the included 3 hole
gasket for this
installation application.
(See below)
Inside DRS Gearbox
DRS Connector
close-up
Terminator Resistor
120 Ω
000-167-746
(supplied)
Ethernet
Page 4
WS200 connection to FI5002 with FI504 and NavNet 3D
NMEA2000 6 meter
Drop cable
000-166-945
(supplied w/ FI-504)
Cut NMEA2000 connector off of
cable and connect the wires to one
of the 6 drop ports inside the
FI-5002.
Match the wire colors to the colors
shown on the drop connector.
Set both Terminal Resistor jumpe r s to
ON to use the FI5002 as the
NMEA2000 Micro cable
1 meter = 000-167-965
2 meter = 000-167-966
6 meter = 000-167-966
NMEA2000 backbone
Appropriate fuse
or circuit breaker
This is to supply voltage for
the NMEA2000 Bus. The
minimum voltage is 9 VDC
and the maximum is 16 VDC.
FI-5002 Junction Box
connector
1
2345
Drop
Page 5
WS200 connection to NavNet 3D
(external NMEA2000 power source)
To activate the internal resistor in the
WS200 antenna, insert the supplied
contact pin into socket #5 in the
connector before connecting it to the
antenna.
“T” Connector
AIR-052-531
Fem/Fem/Male
NMEA2000 Micro Double-
ended cable
Male – Female
1 meter = 000-167-962
2 meter = 000-167-963
6 meter = 000-167-964
This is to supply voltage for
the NMEA2000 Bus. The
minimum voltage is 9 VDC
and the maximum is 16 VDC.
Appropriate fuse
or circuit breaker
NMEA2000 Micro Double-
ended cable
Male – Female
1 meter = 000-167-962
2 meter = 000-167-963
6 meter = 000-167-964
NMEA2000
Terminator
Female
AIR-335-792
“T” Connector
AIR-052-531
Fem/Fem/Male
Loading...