How it Works
Fujitsu
Loading...
fi-590PRB
Operator's Manual
18 pgs785.21 Kb0
Table of contents
Loading...

Fujitsu fi-590PRB Operator's Manual

Download
Page 1
Page 2
Contents
Introduction ................................................................................................................................................. 1
1. Preparations ............................................................................................................................................ 5
1.1 Names of Component Parts .......................................................................................................................... 5
2. Basic Operations .................................................................................................................................... 6
2.1 Installing the Print Cartridge ........................................................................................................................ 6
2.2 Operating Test ............................................................................................................................................... 7
2.3 Positioning the Print Cartridge ..................................................................................................................... 8
2.4 How to Use the Paper Guides ....................................................................................................................... 8
2.5 Print Setup ..................................................................................................................................................... 9
2.6 Replacing the Print Cartridge ..................................................................................................................... 10
3. Daily Care .............................................................................................................................................. 12
3.1 Cleaning the Print Cartridge ....................................................................................................................... 12
3.2 Cleaning the Imprinter ................................................................................................................................ 12
4. Error Messages ..................................................................................................................................... 14
5. Specifications ....................................................................................................................................... 15
Page 3

Introduction

Thank you for purchasing the fi-590PRB Imprinter option for fi-5900C/fi-5950 Color Image Scanner. This guide explains how to install and use the imprinter. (For further details about the functions and operations of fi-5900C/fi-5950 Image Scanner, refer to the “fi-5900C Image Scanner Operator’s Guide” or “fi-5950 Image Scanner Operator’s Guide” included in fi-5900C/fi-5950 SETUP DVD-ROM.) This guide also contains other important information, such as procedures for replacement of consumables. Keep this guide in a convenient and safe place so that you can refer to it whenever necessary. We hope this manual will be helpful in your future use of the fi-590PRF Imprinter.
Manufacturer
PFU LIMITED
Imaging Products Division, Image Products Sales Dept., Products Group Solid Square East Tower 580 Horikawa-cho Saiwai-ku, Kawasaki-shi Kanagawa 212 - 8563 Japan Phone: +81 (44) 540 - 4538
Windows Vista® Home Basic (32/64-bit) Windows Vista (32/64-bit) Windows Vista (32/64-bit) Windows Vista (32/64-bit) Windows Vista (32/64-bit)
Windows Server® 2008 Standard (32/64-bit) Windows Server
Windows® 7 Home Premium (32/64-bit) Windows (32/64-bit) Windows (32/64-bit) Windows (32/64-bit)
®
Home Premium
®
Business
®
Enterprise
®
Ultimate
®
2008 R2 Standard
®
7 Professional
®
7 Enterprise
®
7 Ultimate
*1: Where there is no distinction between the
different versions of the above operating system, the general term "Windows" is used.
Regulatory Information
Windows Vis ta
Windows Server 2008
Windows 7
Windows (*1)
Trademarks
Microsoft, Windows, Windows Vista, and Windows Server are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other product names are the trademarks or registered trademarks of the respective companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) are indicated as follows:
Operating System Indication
Windows® 2000 Professional (Service Pack 4 or later)
Windows® XP Professional (Service Pack 2 or later) Windows Edition Windows (Service Pack 2 or later)
Windows Server® 2003, Standard Edition Windows Server Standard x64 Edition Windows Server Standard Edition Windows Server Standard x64 Edition
®
XP Professional x64
®
XP Home Edition
®
2003,
®
2003 R2,
®
2003 R2,
Windows 2000
Windows XP
Windows Server 2003
Windows (*1)
FCC declaration
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna..
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is located.
- Consult your dealer or an experienced radio/TV technician.
FCC warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
fi-590PRB Imprinter Operator’s Guide | 1
Page 4
Canadian DOC Regulations
This digital apparatus does not exceed the Class A limit for radio noise emissions from digital apparatus set out in the Radio interference Regulations of the Canadian Department of Communications. This Class A digital apparatus complies with Canadian ICES-003.
Le pésent appareil numérique n’ément pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescridtes dans le Réglesment sur le brouillage radioélectrique dicté par le ministere des Communications du Canada. Cet appareil numérique de la classe A est conformme à la norme NMB-003 du Canada.
Bescheinigung des Herstellers / Importeurs
Für den fi-590PRB wid folgendes bescheinigt:
• In Übereinsstimmung mit den Bestimmungen der
EN45014(CE) funkentstört
• Maschinenlärminformationsverordnung
3.GPSGV: Der höchste Schalldruckpegel beträgt 70 dB (A) oder weniger, gemäß EN ISO 7779.
Use in High-safety Applications
This product has been designed and manufactured on the assumption that it will be used in office, personal, domestic, regular industrial, and general-purpose applications. It has not been designed and manufactured for use in applications (simply called "high-safety applications" from here on) that directly involve danger to life and health when a high degree of safety is required, for example, in the control of nuclear reactions at nuclear power facilities, automatic flight control of aircraft, air traffic control, operation control in mass-transport systems, medical equipment for sustaining life, and missile firing control in weapons systems, and when provisionally the safety in question is not ensured. The user should use this product with adopting measures for ensuring safety in such high-safety applications. PFU LIMITED assumes no liability whatsoever for damages arising from use of this product by the user in high-safety applications, and for any claims or compensation for damages by the user or a third party.
Conventions
Warning Indications Used In This Manual
This indication alerts operators to an
WARNING
CAUTION
Symbols Used In This Manual
This manual uses the following symbols in addition to warning indications
ATTENTION
HINT
R
Screen Examples In This Manual
The screen examples in this manual are subject to change without notice in the interest of product improvement. If your displayed screen differs from the screen examples in this manual, operate by following your actual displayed screen while referring to the User's Manual of the scanner application you are using. The screenshots used in this manual are for Windows, TWAIN Driver.
The Operator Panel Language Display
Apart from English, the operator panel can also display French, German, Italian, Spanish, and Chinese (Simplified). In this manual, the language display of the operator panel is shown in English.
operation that, if not strictly observed, may result in severe injury or death.
This indication alerts operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to equipment.
This symbol alerts operators to particularly important information. Be sure to read this information first before proceeding.
This symbol alerts the operator to useful advice on operating the device.
The triangle indicates that special care and attention is required.
A drawing inside the triangle shows what specific caution.
A circle with a slanted line through it indicates an action or step that should not be performed.
Outline characters on a colored background show instructions that users should follow.
It may also include the drawing of the specific instruction.
2 |
Page 5
About Maintenance
The user must not perform repairs on this product. Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service provider to have repairs made on this product.
Safety Precautions
The following describes important warnings for using this product. For the safe use of this product, make sure to follow the following descriptions.
WARNING
Do not insert or drop any foreign objects (water, liquids, small metal objects, etc.) into the opening sections on the scanner. If foreign objects get inside the scanner, immediately disconnect the power cable from the AC outlet. Then, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider. Pay particular attention to this warning in households where there are small children.
If the scanner is damaged for any reason, immediately disconnect the power cable from the AC outlet. Then, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.
In the following situation, immediately disconnect the power cable from the AC outlet. Not doing so may cause a fire or electric shock.
● Smoke or heat coming from the scanner is
detected.
● Strange noise or smell is detected.
● Foreign objects (water, liquids, small metal
objects, etc.) get inside the scanner.
● Other problems which indicate a scanner failure
are detected.
Then, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider. Never try fixing such problems by yourself. Doing so is dangerous.
Do not take apart or modify the scanner as high-voltage components inside the scanner are dangerous. PFU assumes no liability to any damage caused by taking apart the scanner, as doing so is not covered under the warranty.
The area around the part to which this warning label is affixed can become very hot. To avoid burns, never touch around the area indicated by this label.
Firmly insert the power cable into the AC outlet. Not doing so may cause a fire or electric shock.
Use the scanner only at the indicated power voltage and current. Do not connect to multiple-power strips. Improper power voltage or current might cause a fire or electric shock.
Use only power cables provided with the scanner. Do not use any extension cords. Not following these instructions may cause abnormal heat or a fire. Do not also use the power cable provided with the scanner for other devices, since this might cause problems such as an equipment failure, or an electric shock.
Do not install in places that are damp or subject to smoke, steam, or dust, as this may cause a fire or electric shock.
Do not install the scanner in the following locations which are subject to high temperature, humidity, less ventilation, or dust. If placed in an area subject to high temperature, the cover may become overheated and deformed, causing the scanner to become hot, resulting in a fire.
● A place near heat-radiating devices such as
stoves or electric heaters, or flammable items such as volatile inflammable materials or curtain.
● A place such as a bathroom, shower room, or
swimming pool where it may easily get wet.
● A place under direct sunlight, in a car under the
scorching sun, or near heating apparatus where it may get hot.
To avoid injuries, do not place the scanner in an area where small children may be able to reach.
Before moving the scanner, be sure to disconnect the power cable from the AC outlet, and all other interface cables. Make sure that the floor is free of any obstructions. Do not move the scanner with the power and interface cables connected as this can damage the cables, which can later cause a fire, electric shock as well as injuries.
Do not touch the power cable with wet hands. Doing so might cause an electric shock.
When removing the power cable from the AC outlet, make sure to hold the power plug and not the cable. Pulling the power cable may damage it, which may cause a fire or electric shock.
Do not use a damaged power cable. Also, do not insert any cables or power plugs into loose sockets. Doing so may cause a fire or electric shock. Be careful of the following when handling the power cable:
● Do not modify the power cable.
● Do not place heavy objects on the power cable.
● Do not pull or bend the power cable.
If the power cable is damaged, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.
Do not place heavy objects on the scanner or perform other work on top of the scanner. Doing so might cause injuries or an equipment failure.
Do not use the scanner while covered with a blanket, etc. Doing so may raise the temperature inside and cause a fire.
Avoid getting a sleeve, necktie, or hair caught up in any scanner mechanism during scanning since this may cause injuries.
Do not touch the heated section such as the bottom of the scanner for a long time. Doing so may cause a low-temperature burn on your skin.
When the scanner is not going to be used for a long period of time, be sure to disconnect the power cable from the AC outlet. Not doing so may cause a fire or electric shock.
fi-590PRB Imprinter Operator’s Guide | 3
Page 6
CAUTION
Do not use any aerosol sprays or alcohol based sprays to clean the scanner. Dust blown up by strong air from the spray may enter the inside of the scanner. This may cause the scanner to fail or malfunction. Sparks, caused by static electricity, generated when blowing off dust and dirt from the outside of the scanner may cause a fire.
Check the following items once a month:
● The power cable is firmly inserted into the AC
outlet.
● The power cable is not emitting abnormal heat, or
the power cable is not rusted or bent.
● Dust is not accumulated on the power cable. If so,
wipe off any dust with a soft, dry cloth.
● The power cable does not have any cracks or
scratches.
If any abnormality is detected, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider.
Make sure to ground to avoid electric shock. Be sure to ground before plugging into the AC outlet. Unplug from the outlet before removing the ground connection.
When installing the scanner on a table, make sure that the table is flat and level. Place the scanner so that none of its parts extend beyond the edge of the table, otherwise it may fall or collapse and cause injuries.
Install the scanner away from strong magnetic fields and other sources of electronic noise. Protect the scanner against any static electricity and choose a static-free place to install the scanner. Static electricity can cause the scanner to malfunction.
If there is an electrical storm, disconnect the power cable from the AC outlet. Lightening can travel through wires and water pipes and damage the scanner, which may damage your property.
Do not supply the power from the AC outlet where the devices requiring much power such as copying machines or paper shredders are connected.
Do not block the ventilation ports. Blocking the ventilation ports generates heat inside of the scanner, which may result in a fire or scanner failure.
Do not use the scanner immediately after moving it from a cold place into a warm room. Condensation may occur, which might lead to scanning errors. Let the scanner dry for one or two hours before you use it.
When handling documents, be careful not to cut your fingers with them.
When carrying the scanner outside while it is raining or snowing, pay special attention so the scanner does not get wet. If the scanner gets wet, wipe it or wait until it dries.
When transporting the scanner, never carry it alone. The scanner is heavy.
4 |
Page 7

1. Preparations

1.1 Names of Component Parts

Open the Top cover of the scanner (fi-5900C/fi-5950) and you can see the Imprinter (fi-590PRB) installed in the front side.
Top cover
Function
Hopper Height
Power Thickne
Thin
ss
Thick
Send to
Scan
Print cartridge holder
fi-590PRB Imprinter Operator’s Guide | 5
Page 8

2. Basic Operations

2.1 Installing the Print Cartridge

Mount the print cartridge as follows:
5. Open the print cartridge holder, rotating the lever to the left.
ATTENTION
When installing or replacing the print cartridge, be careful not to insert it out of place.
1. Confirm that the scanner is turned off.
2. Press the tabs on the left and right sides of the Top cover and lift to open the Top cover.
Tab
Top cover
3. Remove the new print cartridge from its pouch.
6. Insert the print cartridge in the holder.
Tab
HINT
● Insert the cartridge with its Tab positioned toward
left side and install it.
● Be careful not to let the print cartridge touch or
catch on to the print circuit film.
● Note that the cartridge cannot be inserted properly if
it is inclined.
4. Remove protection tape from the print cartridge.
ATTENTION
Do not touch the metal part of the cartridge nor put the tape back on again.
6 |
7. Turn the lever on the print cartridge toward right to fix it.
Page 9
8. Close the Top cover and press lightly until it is
m
fixed with the tabs.

2.2 Operating Test

After installing the imprinter, test to see if printing can be performed on the Offline Print Test mode.
1. While pressing the [Hopper Height] button (U or V) on the operator panel, switch on the scanner.
Continue pressing on the [Hopper Height] button.
Function
4. Press [Scan] button to test.
Ö Paper will be fed into ADF, and the Imprinter will
print out the Print Test Characters starting at 5mm (±4mm) from the paper’s edge.
HINT
Print test patterns
Test pattern 1 (Horizontal):
ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000
Test pattern 2 (Horizontal）:
abcdefghijklmnopqrstuvwxyz{|}~ 00000000
Test pattern 3 (Horizontal):
!”#$%&'()*+,-./0123456789:;<=>?@00000000
Test pattern 4(Vertical):
ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000
Test pattern 5 (Vertical):
abcdefghijklmnopqrstuvwxyz{|}~ 00000000
Test pattern 6 (Vertical):
!”#$%&'()*+,-./0123456789:;<=>?@00000000
When multiple sheets of documents are placed in the Hopper, the Test Print repeats patterns from 1 through 6. The numbering data portion “00000000” changes from 0 (Zero) with increment of 1(one). (One test pattern is printed at a time. Press the [Scan] button to continue printing the next test pattern.)
Hopper Height
Paper Thicknes s
Thin
Send t o Sca n
Thick
2. Release the [Hopper Height] button when the Function Number Display changes from [P] to [b].
3. Place a blank document on the Hopper.
ATTENTION
● Use A4 or Letter size paper. If the size is
smaller than A4 or Letter, printing may not successfully complete.
● Confirm that the Print Cartridge is
positioned within the document width. For the details, please refer to “2.3 Po the Print Cartridge”.
sitioning
6
5m
5 4 3 2
c
Test pattern print sample
5. To stop Offline Print test mode, turn off the Scanner.
F e e d
i
n g
d
i
r e c t
i
o n
fi-590PRB Imprinter Operator’s Guide | 7
Page 10

2.3 Positioning the Print Cartridge

To Position the print cartridge for printing:
1. Press the tabs on the left and right sides of the top cover, and lift to open the top cover.
Tab
Top cover
3. Close the top cover and press lightly until it is fixed with the tabs.
2. Place the print alignment mark to the position where you want to print.
Print start position
HINT
● The small “T” protruding from the side of the
print cartridge holder indicates the print start position on the page.
● Above the print cartridge tray are document
paper size markings; please use them to adjust for printing positions.
● Do not set the print cartridge within the printing
prohibited area (Fluorescent yellow shaded sections); otherwise, the document may stain with ink.
● Put the actual document in the Hopper and
confirm that the print cartridge is positioned within the document’s width.

2.4 How to Use the Paper Guides

Use the Paper Guides to prevent paper jams due to curling of the edges, as shown below.
Feed direction
As shown below, place the Paper Guides at the ends where the paper edges will pass through.
1. Load the document on the scanner.
2. Open the Top cover.
3. Slide the Paper Guides to the left and right page edges.
Paper Guides
8 |
Page 11
HINT
When you wish to print on the near the edges of a wide width paper, remove the Paper Guide in order to open space for the Print Cartridge, and attach it at the center.
For Right Side Edge Printing
For Left Side Edge Printing
ATTENTION
Be careful not to let the Paper Guide touch or catch onto the print circuit film.
To Attach the Paper Guide
As shown in the illustration below, place the Paper Guide on the rail (c), and push the guide's hook to engage it on to the rail (d).
Paper Guide

2.5 Print Setup

You can configure settings for the imprinter by using the scanner driver dialog box.
TWAIN driver (Example)
Click [Option] button. In [Option] dialog box, choose [Imprinter (Endorser)] tab and specify the Imprinter settings.
Rail
To Remove the Paper Guide
As shown below, hold the Paper Guide and pull towards you to unhook it.
HINT
● Available items are:
● Y offset (Printing)
● Font orientation(vertical, horizontal)/ width
(normal/bold/narrow)
● Strings definition （Max. 43 characters）
● Counter Setup （column, add/subtract,
step）
For the details, please refer to “TWAIN Driver User’s Guide” or “TWAIN Driver Help”
● The following options can be selected on the
[Imprinter (Endorser)] tab.
When either the Pre-Imprinter or the Post-Imprinter is installed:
● [Enable]
● [Disable]
When both the Pre-Imprinter and the Post-Imprinter are installed:
● [Disable]
● [Pre-Imprinter]
● [Post-Imprinter]
fi-590PRB Imprinter Operator’s Guide | 9
Page 12

2.6 Replacing the Print Cartridge

Make sure that you turn off the scanner power and unplug the power cable from the
CAUTION
Replace the Print Cartridge as follows:
outlet.
If the cartridge replacement is done with power turned on, it may cause electric shock or imprinter failure.
4. Take out the Print cartridge from the holder.
5. Take the new Print Cartridge out of its pouch and
detach the protection tape from the Print Cartridge.
ATTENTION
● When the following message appears, replace
the Print Cartridge as soon as possible.
If you continue to print without replacing the cartridge, your print output will continue to appear lighter and lighter.
● When installing or replacing the print cartridge,
be careful not to insert it out of place.
1. Confirm that the scanner is turned off.
2. Press the tabs on the left and right sides of the top cover and lift to open the top cover.
Tab
Top cover
ATTENTION
Do not touch the metal part of the cartridge nor put the tape back again.
6. Insert the Print Cartridge.
Tab
HINT
● Insert the cartridge with its Tab positioned
toward left side and install it.
● Be careful not to let the print cartridge
touch or catch on to the print circuit film.
7. Turn the lever on the print cartridge toward right to fix it.
3. Turn the blue lever toward left and open the cartridge holder.
10 |
Page 13
8. Close the top cover and press lightly until it is fixed with the tabs.
9. Reset the Ink Remain Counter.
You must reset the Ink Remain Counter whenever you replace the print cartridge.
c On the [Start] menu, select [Programs]-[Scanner Utility
for Microsoft Windows]-[Software Operation Panel].
d Select the [Device Setting] tab.
If the [Software Operation Panel] is password protected, enter the password to cancel the View Only mode. (fi-5950 only)
e Click the [Clear] button at the [Remaining Ink (Post)]
button. Ö The Ink remain counter will reset to 100%.
fi-590PRB Imprinter Operator’s Guide | 11
Page 14

3. Daily Care

3.1 Cleaning the Print Cartridge

Poor quality prints can occur due to blocked ink emission holes in the nozzle. Leaving the imprinter unused for long periods can also cause emission holes to become blocked. When the emission holes are blocked, clean the nozzle surface of the print cartridge.
ATTENTION
1. Turn off the Scanner.
2. Remove the Print Cartridge.
(Refer to "2.6 Replacing the Print Cartridge")
For cleaning, use a dry lint-free cloth (DO NOT use tissue), and gently wipe any dirt and stains off the nozzle’s surface.
Nozzle plate
ATTENTION
When cleaning, be careful not to touch the nozzle plate or the contact parts of the cartridge directly by hand.

3.2 Cleaning the Imprinter

Ink may spatter the vicinity of the print cartridge holder.
We recommend you to clean the scanner after 5000 sheets scanning to avoid smudge on the scanned image. Note that the required cleaning cycle may vary depending upon document type to be scanned.
More frequent cleaning may be required when printing a document on which ink does not easily get dry.
When you do the cleaning, turn off the scanner power, and unplug the power cable
CAUTION
ATTENTION
1. Turn off the Scanner.
2. Remove the Print cartridge.
(Refer to “2.6 Replacing the Print Cartridge”)
3.
Press the ADF cover open button.
from the outlet.
If cleaning is done with power turned on, it may cause electric shock or imprinter failure.
For cleaning, use a dry lint-free cloth (DO NOT use tissue).
3. Gently wipe any dirt and stains off the nozzle surface.
4. Make sure that all dirt and stains are removed, before installing the Print Cartridge.
(Refer to “2.6 Replacing the Print Cartridge”)
ATTENTION
When installing or replacing the print cartridge, be careful not to insert it out of place.
Ö The cover is slowly opened.
12 |
Page 15
4. Wipe the following parts using a cloth moistened with Cleaner F1.
ATTENTION
It may take long before the cleaner vaporizes if a large quantity is used. When cleaning the scanner parts, dampen a cloth with modest quantities of the cleaner. In addition, wipe off the cleaner completely with a soft lint-free cloth to leave no residue on the surface of the cleaned parts.
Back of the unit
● When closing the ADF, be sure nothing is
CAUTION
left inside of the ADF.
● Be careful not to pinch your fingers.
6. Insert the Print cartridge.
(Refer to “2.6 Replacing the Print Cartridge”)
Imprinter head
5. Hold the ADF cover with both hands and press it down slowly.
Press the ADF cover until it is fixed.
fi-590PRB Imprinter Operator’s Guide | 13
Page 16

4. Error Messages

The following numbers or letters on the Function Number Display indicates a malfunction in the imprinter.
Description: The print cartridge is not installed.
How to solve: Open the top cover and confirm that the print
cartridge is installed correctly.
Description: A problem occurred to the Imprinter.
How to solve: cOpen the top cover and confirm that the print
cartridge has been installed correctly.
dTurn off the scanner and then turn it on again.
(If the problem occurs again, contact the store where you purchased the imprinter or contact an authorized FUJISTU scanner service provider.)
Description: The imprinter fuse has blown out.
How to solve: Contact the store where you purchased the
scanner, or contact an authorized FUJITSU scanner service provider.
ATTENTION
For other errors, refer to “fi-5900C Image Scanner Operator’s Guide” or “fi-5950 Image Scanner Operator’s Guide” included in fi-5900C/fi-5950 SETUP DVD-ROM.
14 |
Page 17

5. Specifications

g
p
Item Specification
Printing Method Thermal inkjet printin Print Timing Post Printing Characters
Maximum number of characters per line
Print orientation
Character size
Character pitch 3.79mm / 0.1492in (Normal), 2.46mm /0.0968in (Narrow) Font style Regular, Bold Character width Normal, Narrow
Document that can be scanned
rinting (Backside) Alphabet : A to Z, a to z Numeric Characters : 0, 1 to 9 Symbols : ! ” $ # % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _` { | } ¯ 43 characters
Normal: 0º, 180º (horizontal orientation), 90º, 270º (vertical orientation) Narrow: 0º, 180º (horizontal orientation)
Normal: Height 2.91mm × width 3.03mm / 0.1146 × 0. 1193 in (horizontal orientation)
Height 3.03mm × width 2.91mm / 0. 1193 × 0.1146 in (vertical orientation)
Narrow: Height 2.91mm × width 1.71mm / 0.1146 × 0.0673 in (horizontal orientation)
Character width Print orientation Font style Printing
Horizontal
Normal
Vertical
Horizontal
Narrow
Vertical
Regular Available
Bold Available
Regular Available
Bold Available
Regular Available
Bold NOT Available
Regular NOT Available
Bold NOT Available
Documents supported by fi-5900C/fi-5950 For the details, please refer to “fi-5900C Image Scanner Operator’s Guide” or “fi-5950 Image Scanner Operator’s Guide”-“Chapter 7 Document Specification.”
ATTENTION
Documents with glossy surface such as thermal paper, thermal transfer paper, coated paper, and art paper take longer time for the ink to dry and may cause poor print quality. The imprinter must be cleaned more frequently if you use these types of papers.
fi-590PRB Imprinter Operator’s Guide | 15
Page 18
m
p
Item Specification
Printing area
Head movable range
Post-printing area (back side)
Reference Point
Feeding direction
* The document stains with ink when
the shaded areas (shown in the illustration). Therefore, correct printing operations in such areas are not guaranteed.
Character position accuracy
Ambient condition Temperature: 15 to 35ºC (59 to 95ºF), Humidity: 20 to 80% Consumable Print Cartridge (P/N: CA00050-0262)
16 |
Vertical: ±4mm (at reference position) Horizontal: ±4mm (at reference position)
Replacement Cycle : 4,000,000 characters
The number of characters may decrease depending on the font selection.)
(
Unit: m
rinting in
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use