Fujitsu SP93GX, SP620C, SP3091DC, SP3092DC, FI-4220C-C2 User Manual

...
0 (0)

Fujitsu SCSI Scanner Installation Procedures

Windows 95\98\98SE\ME\2000\XP

If you are installing the following models by means of the SCSI interface then use this document.

SP10C

M3093GX\DG

Fi-4530C

Fi-5120C

SP15C

M3096GX

Fi-4640S

Fi-5220C

SP600C

M3097G\G+\DG

M4097D

Fi-5530C

SP620C

M3099G\GX\GH

Fi-4750C\L

Fi-5650C

SP3091DC

FI-4120C\C2

M4099D

Fi-5750C

SP3092DC

Fi-4220C\C2

Fi-4860C

Fi-5900C

SP93GX

Fi-4340C

Fi-4990C

 

If you are going to use the USB interface of a dual SCSI/USB model then use the USB scanner installation guide. For Scansnap models please use the Scansnap installation guide.

Hardware requirements.

You will need a PC system that meets our recommended specifications, an appropriate SCSI controller, and a SCSI cable (six foot recommended maximum). For recommended PC system specifications and SCSI controllers please reference the Scanner Hardware Reference page. You may also need your Operating System Disk.

Step A: Installing the SCSI Host Adapter (Adaptec).

1.Shut down your PC and remove the case cover.

2.Locate a free PCI slot and remove the back plate if necessary.

3.Install the SCSI controller in an open PCI slot.

Make sure that the card is seated completely in the slot and secured in the frame

Warning! Failure to secure the SCSI controller in the PC can result in damage to the SCSI card, scanner, and/or your system.

4. Boot your PC without the scanner attached.

Step B: Installing the SCSI drivers (Adaptec).

5.When the New Hardware wizard comes up, allow Windows to finish installing the hardware files for the SCSI controller.

6.Then either install/update the ASPI drivers from the CD or go to www.adaptec.com, and click on the “search” tab.

7.For Windows 95\98 or ME scroll down to the “Enter key word or quoted phrase” box and type in “aspi32”.

8.Next scroll down to the drivers section, click on ASPI32 and follow the prompts to download it your desktop or a new folder.

9.Afterwards go to that location and double click on the "aspi32.exe" icon and follow the prompts.

10.When the message “ASPI is up to date” appears, reboot and go to the next step.

Rev051906A

Page 1 of 7

Fujitsu SCSI Scanner Installation Procedures

Windows 95\98\98SE\ME\2000\XP

11.For Windows 2000 or XP scroll down to the “Enter key word or quoted phrase” box and type in “aspi”.

12.Next scroll down to the drivers section, click on ASPI_v470 or higher and follow the prompts to download it.

13.Afterwards go to that folder and unzip the file to the default Adaptec\ASPI folder.

14.Then go to start, run, browse to the Adaptec\ASPI folder, select ASPIINST.EXE and run it.

15.When the message “ASPI is up to date” appears, reboot and go to the next step.

Step C: Installing the drivers from the Setup CD.

To begin it is recommended that you install the drivers first before connecting the scanner.

Installing the STI-Twain driver.

1.Insert the Scanner Setup CD into your CD Rom.

2.Next please complete the pre-registration box when it appears and click the submit button.

3.Afterwards close your browser and click the Install Products button on the Scanner Setup Menu.

4.On the next screen click on Twain Driver and you may be presented with the option to install the Error Recovery Guide.

5.After you have installed the Error Recovery Guide (or not) follow the prompts to complete the twain driver installation.

6.Do not reboot at this time!

Installing the ASPI-Twain driver.

Some of our scanners are not supported by the STI-Twain drivers. For those units you must install the ASPI-Twain driver. Please refer to the driver download page to see if your model is one of them.

7.Insert the Scanner Setup CD into your CD Rom.

8.Next please complete the pre-registration box when it appears and click the submit button.

9.Afterwards close your browser and click the Install Products button on the Scanner Setup Menu.

10.On the next screen click on Twain Driver and you may be presented with the option to install the Error Recovery Guide.

11.After you have installed the Error Recovery Guide (or not) follow the prompts to complete the twain driver installation.

12.Do not reboot at this time!

Installing the ISIS driver.

13.Next go back to the Scanner Setup Menu and click on ISIS Driver.

14.If you didn’t install the Error Recovery Guide during the Twain driver installation you will be asked again. Proceed and follow the prompts to complete the ISIS driver installation.

15.Do not reboot at this time!

Rev051906A

Page 2 of 7

Fujitsu SCSI Scanner Installation Procedures

Windows 95\98\98SE\ME\2000\XP

Installing ScandAll 21.

16.Back to the Scanner Setup Menu and click on Software Utility - ScandAll 21.

17.The ScandAll 21 installation wizard will appear. Click next and follow the prompts to complete the installation.

18.Once all of the above is completed then remove the Scanner Setup CD, Reboot your system, and go to Step E.

Step D: Installing the drivers from our Web Page.

Installing the STI-Twain driver.

1.Create a new folder and name it Fujitsu Downloads.

2.Next go to the following link Drivers and Downloads.

3.Fill in the pre-registration box when it pops up and continue to the drivers download page.

4.Afterwards click on STI Twain Software Drivers.

5.Scroll down the list of scanner models in the left column and select the appropriate STI Twain driver to the right of your scanner model.

6.Double click on the driver file name and the File Download box will popup.

7.Click on Save and then use the browse (or other folder navigation) button until you have the Twain Download folder you created in the Save As box.

8.Click Save.

9.When completed close the Download Complete window and go to the Twain Download folder.

10.Open the folder and you will see the saved driver file. Double click on the file to unzip it and the WinZip* self-extractor box will popup. Click on browse and select the Fujitsu Downloads folder, then click on Extract. The file will begin to unzip and when finished a message box will report the number of files unzipped. Click on OK and close WinZip.

11.In the STI Twain Download folder locate the setup.exe file and double click. Afterwards follow the prompts and reboot when finished

Installing the ASPI-Twain driver.

Some of our scanners are not supported by the STI-Twain drivers. For those units you must install the ASPI-Twain driver. Please refer to the driver download page to see if your model is one of them.

1.Create a new folder and name it Fujitsu Downloads.

2.Next go to the following link and click on Drivers and Downloads.

3.Fill in the pre-registration box when it pops up and continue to the drivers download page.

4.Afterwards click on ASPI Twain Software Drivers.

5.Scroll down the list of scanner models in the left column and select the appropriate ASPI Twain driver to the right of your scanner model.

6.Double click on the driver file name and the File Download box will popup.

7.Click on Save and then use the browse (or other folder navigation) button until you have the Twain Download folder you created in the Save As box.

8.Click Save.

9.When completed close the Download Complete window and go to the Twain Download folder.

Rev051906A

Page 3 of 7

Loading...
+ 4 hidden pages