Fujitsu fi-5900C Installation Guide

Fujitsu SCSI Scanner Installation Procedures

Windows NT 4.0

If you are installing the following models by means of the SCSI interface then use this
document.

SP10C M3093GX\DG Fi-4530C Fi-5120C
SP15C M3096GX Fi-4640S Fi-5220C
SP600C M3097G\G+\DG M4097D Fi-5530C
SP620C M3099G\GX\GH Fi-4750C\L Fi-5650C
SP3091DC FI-4120C\C2 M4099D Fi-5750C
SP3092DC Fi-4220C\C2 Fi-4860C Fi-5900C
SP93GX Fi-4340C Fi-4990C

If you are going to use the USB interface of a dual SCSI/USB model then use the USB scanner
installation guide. For Scansnap models please use the Scansnap installation guide.

Hardware requirements.

You will need a PC system that meets our recommended specifications, an appropriate SCSI
controller, and a SCSI cable (six foot recommended maximum). For recommended PC system
specifications and SCSI controllers please reference the
You may also need your Operating System Disk.

Step A: Installing the SCSI Host Adapter (Adaptec).

1. Shut down your PC and remove the case cover.

2. Locate a free PCI slot and remove the back plate if necessary.

3. Install the SCSI controller in an open PCI slot.
Make sure that the card is seated completely in the slot and secured in the frame

Warning! Failure to secure the SCSI controller in the PC can result in damage to the
SCSI card, scanner, and/or your system.

4. Boot your PC without the scanner attached

Step B: Installing the SCSI drivers (Adaptec).

Although Windows NT has driver support for your host adapter it does not support plug and
play. Therefore the SCSI drivers will need to be loaded manually. Follow the instruction below
to install the driver for your host adapter.

Rev051906A Page 1 of 9

Scanner Hardware Reference page.

.

Fujitsu SCSI Scanner Installation Procedures

Windows NT 4.0

1. Login with administrator rights.

2. Go to Start, Control Panel, SCSI Adapters.

3. Then click on the Drivers tab and click ‘Add.’

4. Next select ‘Adaptec’ under Manufacturers

5. On the next menu scroll down again and double click on the line that reads –
‘AHA294x\AHA394x or AIC78xx PCI SCSI controller.’

Rev051906A Page 2 of 9

Fujitsu SCSI Scanner Installation Procedures

Windows NT 4.0

6. Insert your WinNT CD system disk and click OK.

7. When prompted to reboot, select no.

8. Then go to
“Enter key word or quoted phrase” box and type in “aspi32.exe.”

9. Next scroll down to the drivers section, click on “aspi32.exe” and follow the prompts
to download it to your desktop or a new folder.

10. Afterwards go to that location and double click on the "aspi32.exe" icon.

11. Follow the prompts and then reboot.

If there are no errors then shut down your system and go to the next step.
Special note: If you are using a different SCSI controller than what is shown in these examples

then select the “Have Disk” button, insert your driver CD into the CD Rom, and follow the
prompts.

Check the SCSI drivers

• Once the driver has been added, return to Control Panel

• Double-click on ‘Devices’

• Search for ‘aic78xx’ under Device

www.adaptec.com, and click on the “search” tab. Scroll down to the

Ensure the aic78xx entry under Device displays ‘Started’ under Status and ‘Boot’ under Startup
as seen here. Ensure ‘Aspi32’ entry under Device displays ‘Started’ under Status and
‘Automatic’ under Startup as seen above.

Rev051906A Page 3 of 9