Fisher Paykel WB60S Installation Manual
INSTALLATION INSTRUCTIONS
Warming Drawer
WB60S models
NZ AU GB IE
590513C 04.13
1
SAFETY AND WARNINGS
Electrical shock hazard
WARNING!
Cut hazard
WARNING!
2
Before carrying out any work on the
electrical section of the appliance, it
must be disconnected from the mains
electricity supply.
Connection to a good earth wiring
system is absolutely essential and
mandatory.
Alterations to the domestic wiring
system must only be made by a qualified
electrician.
Failure to follow this advice may result
in electrical shock or death.
WARNING!
Fire hazard
Do not use adapters, reducers, or
branching devices to connect this
appliance to the mains power supply.
Take care - some panel edges are sharp.
Failure to use caution could result in
injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS!
To reduce the risk of fire, electrical shock, injury
to person, or damage when using the warming
drawer, please read these instructions carefully
before installing this product.
Please make this information available to the
person installing the product – doing so may
reduce your installation costs.
Installation work, maintenance and repairs may
only be carried out by suitably qualified and
competent persons in accordance with national
and local safety regulations.
Always disconnect the power supply prior to
carrying out any installation, maintenance or
repair work.
Before installation make sure that the voltage
Failure to follow this advice may result
in overheating, burning, or fire.
and frequency listed on the data plate
corresponds with the household electrical supply.
1
SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTIONS!
When installing companion products the weight
of the companion product should be distributed
3
The electrical outlet should be easily accessible
after installation.
When a companion product is installed in
combination with the warming drawer to the
same circuit, operating both products may
cause an overload. If in doubt consult a qualified
electrician.
When installed in combination with a companion
product the companion product may be placed
directly onto the warming drawer. It is not
necessary to place a shelf between the products. A
built- in shelf at the base of the cabinetry able to
support the weight of both products is required.
If installing the warming drawer directly
underneath an oven, ensure you do not damage
the oven’s lower trim. The lower trim ensures
correct air circulation to the oven and allows
the door to open and close without obstruction.
Fisher & Paykel does not accept any responsibility
for any damage resulting from incorrect
installation.
The maximum weight the warming drawer is able
to support is 60 kg.
The warming drawer is not designed for use in
mobile installations such as recreational vehicles,
boats or aircraft.
across the edges of the warming drawer. Products
above which rest on “feet” may only be installed
if the feet of the product lie within 70mm of
the sides of the warming drawer, as this area
is reinforced. Failure to do this may result in
damage to the warming drawer and companion
product.
Before installing the warming drawer you must
inspect it for any signs of damage. Under no
circumstances should you install or use the
warming drawer if it has been damaged.
If the power supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or a similarly qualified tradesperson in order to
avoid a hazard. .
Connect the warming drawer to a properly rated,
protected and sized power supply circuit to avoid
electrical overload.
Do not use an extension cord or a portable
electrical outlet device (e.g. multi-socket outlet
box) to connect the Warming Drawer to the
power supply. Make sure the power supply cord is
located so that it will not be stepped on, tripped
over or otherwise subject to damage or stress.
Ensure the connection to power supply is
accessible after installation.
2
PARTS SUPPLIED
Screws (4) Anti-tip bracket (1) Oven support brackets (2)
3
PRIOR TO INSTALLATION
the cavity is square and level, and of the required dimensions.
the installation will comply with all clearance requirements and applicable standards and regulations.
the power switch will be easily accessible to the customer when the warming drawer is installed.
the warming drawer (and any product on top of it) will rest on a surface that can support its weight.
the height from the floor suits the customer.
you consult local building authorities and by-laws if in doubt regarding installation.
4
If installing with a companion product
Important!
If installing with a companion product please refer to the installation instructions of that product to ensure the installation requirements of BOTH products are met.
When installing products on top of the warming drawer, the weight of the product should be distributed across the edges of the warming drawer.
Products above which rest on “feet” may only be installed if the feet of the product lie within 70mm of the sides of the warming drawer, as this area is reinforced.
Failure to do this may result in damage to the warming drawer and companion product.
70 mm 70 mm
Feet
Warming Drawer can withstand a
maximum weight of 60 kg
Loading...