Epson Stylus Pro 7880/9880
l
t
Printer Parts
These illustrations show the Epson Stylus Pro 9880 but the
parts are the same for the Pro 7880 unless otherwise noted.
Front
Roll paper
on spindle
Roll paper
mounting bracket
Front
cover
Left ink
cartridge
compartment
Paper
basket
Roll paper
cover
Control pane
Paper lever
Right ink
cartridge
compartmen
Printer
stand
Casters
Printer Specifications
Electrical
Input voltage range 90 to 264 V
Rated frequency range 50 to 60 Hz
Input frequency range 49 to 61 Hz
Rated current 1.0 A at 120 V
0.5 A at 220 V
Power consumption
(approx.)
Check the label on the back of your printer for voltage
information.
Dimensions and Weight
Epson Stylus Pro 7880:
Approx. 50 W
6 W or less in sleep mode
1 W or less in power off mode
Epson Stylus Pro 9880:
Approx. 58 W
6 W or less in standby mode
1 W or less in power off mode
Back
Network
interface
Maintenance
tank
Paper straps
(Pro 9880 only)
USB
interface
Maintenance
tank (Pro
9880 only)
AC
inlet
Dimensions Epson Stylus Pro 7880:
Width: 47.12 inches (1178 mm)
Depth: 20.04 inches (501 mm)
Height: 22.4 inches (560 mm)
(without stand)
Epson Stylus Pro 9880:
Width: 68.08 inches (1702 mm)
Depth: 27.12 inches (678 mm)
Height: 47.84 inches (1196 mm)
Weight
(without consumables)
Epson Stylus Pro 7880:
108 lb (49 kg)
Epson Stylus Pro 9880:
198 lb (90 kg)
Stand: 23.1 lb (10.5 kg)
1 - Epson Stylus Pro 7880/9880 10/07
Epson Stylus Pro 7880/9880
Environmental
Temperature Operation: 50 to 95 °F (10 to 35 °C)
Print
quality
guarantee: 59 to 77 °F (15 to 25 °C)
Storage:
–4 to 104 °F (–20 to 40 °C)
1 month at 104 °F (40 °C)
Humidity
(without
condensation)
Operation: 20 to 80% RH
Print
quality
guarantee: 40 to 60% RH
Storage: 20 to 85% RH
(stored in container)
Media
Roll paper
Maximum roll width Epson Stylus Pro 7880:
24 inches (610 mm)
Epson Stylus Pro 9880:
44 inches (1118 mm)
Maximum roll length Up to 150 feet for 2-inch cored
media
Up to 673 feet for 3-inch cored
media
Weight range 17 to 24 lb (64 to 90 g/sm)
Paper thickness 0.003 to 0.004 inches
(0.08 to 0.11 mm)
Roll paper compatibility Handles both 2- and 3-inch cored
media
Maximum roll paper
diameter
Cut Sheets
Weight range 17 lb (64 g/m
2-inch core: 4 inches (101.6 mm)
3-inch core: 6 inches (152.4 mm)
2
) bond up to
posterboard
Epson Cut Sheet Paper Sizes
Size group Size name Measurements
A Series A4 8.3 × 11.7 inches
A3 11.7 × 16.5 inches
Super A3/B 13 × 19 inches
A2 16.5 × 23.4 inches
A1 23.4 × 33.1 inches
Super A1 24 × 36 inches
A0* 33.1 × 44 inches
Super A0* 36 × 50.9 inches
US-ANSI Letter 8.5 × 11 inches
US B 11 × 17 inches
US C 17 × 22 inches
US D 22 × 34 inches
US E* 34 × 44 inches
US-ARCH ARCH A 9 × 12 inches
ARCH B 12 × 18 inches
ARCH C 18 × 24 inches
ARCH D 24 × 36 inches
ARCH E* 36 × 48 inches
B Series B5 7.2
B4 10.1 × 14.2 inches
B3 14.2 × 20.3 inches
B2 20.3 × 28.7 inches (
B1* 28.7 × 40.5 inches
(210×297mm)
(297×420mm)
(329×483mm)
(420×594mm)
(594×841mm)
(610×910mm)
(841×1189mm)
(914×1292mm)
(216×279mm)
(279×430mm)
(430×559mm)
(559×864mm)
(864×1120mm)
(229×305mm)
(305×457mm)
(457×610mm)
(610×910mm)
(910×1219mm)
× 10.1 inches
(182×257mm)
(257×364mm)
(364×515mm)
515 × 728 mm)
(728×1030mm)
10/07 Epson Stylus Pro 7880/9880 - 2
Epson Stylus Pro 7880/9880
Epson Cut Sheet Paper Sizes
Size group Size name Measurements
B1 Landscape* 40.5 × 28.7 inches
(1030 × 728 mm)
B0 40.5 × 57.3 inches
(1030 × 1456 mm)
Super B0* 44 × 62.2 inches
(1118 × 1580 mm)
Photo Series — 8 × 10 inches
(203 × 254 mm)
— 10 × 12 inches
(254 × 305 mm)
— 11 × 14 inches
(279 × 356 mm)
— 12 × 12 inches
(305 × 305 mm)
— 16 × 20 inches
(406 × 508 mm)
Others — 24 × 30 inches
(610 × 762 mm)
— 30 × 40 inches*
(762 × 1016 mm)
— 36 × 44 inches*
(914 × 1118 mm)
— 11.8 × 15.7 inches
(30 × 40 cm)
— 15.7 × 23.6 inches
(40 × 60 cm)
— 23.6 × 35.4 inches
(60 × 90 cm)
*Epson Stylus Pro 9880 only
Note:
Since the quality of any particular brand or type of paper may be
changed by the manufacturer at any time, Epson cannot attest to the
quality of any non-Epson brand or type of paper. Always test samples
of paper stock before purchasing large quantities or printing large
jobs.
Safety Approvals
Safety standards UL 60950
CSA 22.2 No. 60950
EMC FCC part 15 subpart B, class B
CAN/CSA-CEI/IEC CISPR 22 class B
Printer Interfaces
USB (1.1 and 2.0 compatible)
Ethernet 10/100 BaseT
Ink Cartridges
Cartridge life 2 years from production date if unopened;
within 6 months after opening package.
Temperature
(storage)
Capacity 110 or 220 ml
Weight 110 ml: approx. 8.82 oz (250 g)
Note:
We recommend that you use genuine Epson cartridges and do not
refill them. The use of other products may affect your print quality
and could result in printer damage.
Yields vary considerably based on images printed, print settings,
paper type, frequency of use, and temperature. For print quality, a
small amount of ink remains in the cartridge after the “replace
cartridge” indicator comes on. The printer ships with full cartridges
and part of the ink from this first set of cartridges is used for priming
the printer.
For best printing results, use up a cartridge within six months of
opening the package.
–4 to 104 °F (–20 to 40 °C); 1 month at
104 °F (40 °C); installed or uninstalled
220 ml: approx. 13.05 oz (370 g)
Printable Area
Default roll paper margins are 0.59 inch (15 mm) top and
bottom, and 0.12 inch (3 mm) right and left. Using the menu
system, you can set all the margins to 15 mm or 3 mm, or set
the top margin to 35 mm.
The borderless printing feature allows edge-to-edge printing
on some media.
3 - Epson Stylus Pro 7880/9880 10/07
Epson Stylus Pro 7880/9880
Consumables and Accessories
Ink Cartridges
Use the following UltraChrome K3™ Epson ink cartridges:
Slot no. Cartridge 110 ml 220 ml
1 Light Light Black T602900 T603900
2 Vivid Light Magenta T602600 T603600
3 Light Cyan T602500 T603500
4 Light Black T602700 T603700
5 P hoto Black T602100 T603100
Matte Black T611800 T612800
6 Cyan T602200 T603200
7 Vivid Magenta T602300 T603300
8 Yellow T602400 T603400
User-Replaceable Parts
You can order these user-replaceable parts:
Part Part number
Replacement Ink Maintenance Tank C12C890191
Replacement Printer Cutter Blade C12C815291
You can purchase optional equipment and genuine Epson ink
and paper from an Epson Professional Imaging Authorized
Reseller. To find the nearest reseller, visit
www.proimaging.epson.com (U.S. sales), www.epson.ca
(Canadian sales), or call 800-GO-EPSON (800-463-7766).
Or you can purchase online at www.proimaging.epson.com
(U.S. sales) or www.epson.ca (Canadian sales).
Control Panel
Control Panel Button and Lights
Enter or
cut button
Left arrow or
paper source
button
Paper
feed up
button
Paper feed
down button
Menu or
cleaning
button
Power
light
Power
button
Paper
light
Pause or
reset button
and light
Ink
light
LCD
display
Options
Your Epson Stylus Pro 7880/9880 offers these options:
Option Part number
Automatic Take-Up Reel System (Pro 9880 only) C12C815251
Replacement 44-inch Take-U p Reel Core
(Pro 9880 only)
Paper Roller Spindle (Normal Tension ) — 2- or 3- in ch
EpsonStylus Pro7880
Epson Stylus Pro9880
Paper Roller Spindle (High Tension) — 2- or 3-inch
EpsonStylus Pro7880
Epson Stylus Pro9880
Manual Media Cutting System
EpsonStylus Pro7880
EpsonStylus Pro9880
Replacement Manual Cutting Blade (for Manual Media
Cutting System)
One-year extended warranty* EPP7898B1
Two-year extended warranty* EPP7898B2
*Must be purchased within 12 months of printer purchase.
C815121
C12C811161
C12C811151
C12C811155
C12C811152
C12C815231
C815182
C815192
Menu Setting Summary
Press the Menu button to enter menu mode. See the
User’s Guide for details on these settings.
Menu setting Description
PRINTER SETUP menu
ROLL PAPER
COUNTER
PLATEN GAP Adjusts the distance from the print hea d to the
PAGE LINE Selects whether to print a cut off line between
Alerts you when roll paper is running low. Set
the paper length and at what remaining length
you want to be alerted. (To use, first select
ROLL as the REMAINING PPR SETUP setting in
Maintenance mode
paper
STANDARD for most printing
WIDE or WIDER if images are smeared
NARROW for thin paper
WIDEST for thick paper
pages on roll paper
10/07 Epson Stylus Pro 7880/9880 - 4
Epson Stylus Pro 7880/9880
Menu setting Description
INTERFACE Selects an interface for receiving print jobs.
AUTO to automatically select the i nterface
when it receives a print job
USB to receive only print jobs sent to the USB
interface
NETWORK to receive only print jobs sent t o th e
network interface
CODE PAGE Selects the code page for your data
PC437 for extended graphics data codes
PC850 for multilingual data codes
ROLL PAPER
MARGIN
Selects the margins for roll papers.
DEFAULT (15 mm all around)
TOP/BOTTOM 15 mm (3 mm left/right)
TOP 35/BOTTOM 15 mm (3 mm left/right)
3 mm (all around)
15 mm (all around)
PAPER SIZE CHECK Selects whether the printer checks to see if the
width of the loaded paper matches the width
selected in your print job (ON is recommended).
PAPER SKEW
CHECK
Selects whether the printer alerts you if paper is
not feeding straight by displaying PAPER SKEW
on the LCD display and stopping printing. If you
select OFF, you do not receive an error even if
the print job is out of range of the loaded paper.
TIME OUT Selects the time interval before cancelling a
print job if the printer cable is unplugged or the
printer hangs (range is 30 to 300 seconds).
CUTTER
ADJUSTMENT
Prints cutter adjustment patterns and allows
you to adjust the cutting position if you print
with no top or bottom margins.
REFRESH MARGIN Selects whether to automatically leave an extra
margin area after borderless print jobs.
AUTO NOZZLE
CHECK
Selects whether to automatically chec k the
print head nozzles before printing each print job.
Do not select ON if using non-Epson media or
paper narrower than 8.26 inches (210 mm).
(Available only when AUTO CLEANING setting
ON.)
is set to
AUTO CLEANING Selects whether to automatically check and
clean the print head, if necessary, when you run
a nozzle check from the control panel or printer
driver. Do not select ON if using non-Epson
media or paper narrower than 8.26inch e s
(210 mm).
QUIET CUT Selects whether to cut printouts slowly to
decrease cutting noise and paper particles.
INITIALIZE
SETTINGS
Resets the PRINTER SETUP menu settings to
their default settings.
TEST PRINT menu
NOZZLE CHECK Prints a nozzle check pattern
STATUS SHEET Pri nts a sheet showing the status of various
printer parts and settings
NETWORK STATUS
SHEET
Prints a sheet showing the network settings;
see the on-screen Network Guide for details.
Menu setting Description
JOB
INFORMATION
Prints a sheet showing information about the
last 10 print jobs.
CUSTOM PAPER Prints information about paper configurations
you have created
PRINTER STATUS menu
VERSION Displays the printer’s firmware version number.
PRINTABLE PAGES Displays an estimate of the number of pages
that can be printed based on the ink cartridge
status.
INK LEVEL Displays the status of the ink in the cartridges.
MAINTENANCE
Displays the status of the mainte nance tank.
TANK
USAGE COUNT Displays the approximate amount of ink and
paper used.
CLEAR USAGE
Clears the values displayed in USAGE COUNT.
COUNT
JOB HISTORY Displays the approximate amount of ink and
paper used in the last 10 print jobs.
TOTAL PRINTS Displays the total number of pages printed.
SERVICE LIFE Displays the service life of each printer part.
EDM STATUS For future enhancements to the printer; no
settings necessary.
CUSTOM PAPER menu
PAPER NUMBER Selects the number for each special paper
configuration you create using th e se tt ings
below.
PLATEN GAP Adjusts the distance from the print head to the
paper.
STANDARD for most printing
WIDE or WIDER if images are smeared
NARROW for thin paper
WIDEST for thick paper
THICKNESS
PATTERN
THICKNESS
NUMBER
Prints a thickness patterns so you can select a
THICKNESS NUMBER setting below.
Selects the thickness number for the best
pattern printed using the THICKNE SS PATTERN
setting above.
CUT METHOD Selects the cutting blade pressure you want to
use for the paper.
STANDARD
THIN PAPER
THICK PAPER, FAST
THICK PAPER, SLOW
PAPER FEED
ADJUST
Adjusts the amount of paper fed during printing
to help eliminate banding (–0.70 to 0.70%).
Choose a lower value if you see white lines on
your prints, or a higher value i f you see dark
lines.
DRYING TIME Selects a drying time for ink to avoid smearing
(from 0 to 10 seconds).
5 - Epson Stylus Pro 7880/9880 10/07
Epson Stylus Pro 7880/9880
Menu setting Description
PAPER SUCTION Adjusts the suction pressure when printing on
M/W
ADJUSTMENT
MAINTENANCE menu
CUTTER
REPLACEMENT
BK INK CHANGE Starts the procedure to replace the black ink
POWER CLEANING Starts a print head power cleaning cycle
CLOCK SETTING Sets the printer date and time setti ngs
CONTRAST
ADJUSTMENT
HEAD ALIGNMENT menu
PAPER THICKNESS Select the paper thickness for aligning the print
ALIGNMENT Select and start running print head alignment of
NETWORK SETUP menu
(see the on-screen Network Guide for details)
NETWORK SETUP Select to enable or disable network printing and
IP ADDRESS
SETTING
IP, SM, DG
SETTING
BONJOUR Select the Bonjour network settings, if
INIT NETWORK
SETTING
thin paper or backlight film.
STANDARD
to –4
–1
Adjust the intensity of the Micr oWeave pattern
to improve print quality, but lower print speed.
STANDARD
or 2
1
Starts procedure to replace the paper cutter
blade
cartridge type
Adjusts the contrast of the LCD display.
head.
various types.
select the settings below.
Select to set the IP address automatic ally or
manually.
Enter the IP address settings, if selecting the
address manually.
necessary.
Returns the network settings to t heir default
settings.
Printing Status Information
The status check sheet shows some of the current default
settings, the amount of ink remaining in each cartridge, the
page count, and the status of various printer parts.
1. Make sure paper is loaded in the printer.
2. Press the
3. Press the d button to highlight
Menu.
4. Press d to highlight
You see
Menu button.
TEST PRINT, then press
STATUS SHEET, then press Menu.
PRINT.
5. Press to start printing.
The amount of ink left or the maintenance tank capacity is
indicated as follows:
E[*****]F = 100–81% of ink or maintenance tank capacity
remaining
E[**** ]F = 80–61%
E[*** ]F = 60–41%
E[** ]F = 40–21%
E[* ]F = 20–11%
% = less than 10% of ink or maintenance tank capacity
remaining
Replacing Ink Cartridges
The easiest way of checking ink levels is from the control
panel LCD display. The numbers below the ink icons on the
LCD display correspond to the 8 ink cartridge slots on the
printer. The icons show the approximate amount of ink
remaining as follows:
100–81% 20% or less
80–61% Ink low
60–41% Ink expended
40–21% Cartridge error or no cartridge
When the red
the LCD display, the indicated cartridge is almost expended.
Make sure you have a replacemen t cartridge. When the lights
stay on and
cartridge is expended. You must replace the cartridge before
you can continue printing.
See page 4 for information on selecting the correct
replacement cartridges. You can install any combination of
110 ml and 220 ml cartridges. Before you start, make sure the
printer is powered on. Then follow these steps to replace an
ink cartridge:
1. Note the color of the cartridge that is low or expended. This
is the cartridge you need to replace.
2. Press the ink compartment covers to open them.
Caution:
Leave the expended cartridge in the printer until you are ready to
replace it.
To prevent ink reporting errors, never replace the ink cartridges
with the printer turned off.
B Ink light is flashing and INK LOW appears on
REPLACE INK CARTRIDGE is displayed, the
10/07 Epson Stylus Pro 7880/9880 - 6
Epson Stylus Pro 7880/9880
6. Gently shake the cartridge well before installing it.
7. Hold the cartridge with the arrow pointing toward the
printer. Then insert the cartridge into the slot. Don’t force
it in.
3. Raise the ink levers to the unlocked position.
4. Remove the expended ink cartridge from the printer. It’s a
good idea to save your first set of expended cartridges so you
can use them for transporting the printer, if necessary.
Warning:
Do not shake the expended cartridge, or ink may leak out. If ink
gets on your hands, wash them thoroughly with soap and water.
If ink gets in your eyes, flush them immediately with water.
Note:
If you can’t insert the cartridge smoothly, you may have the
wrong cartridge. Check the package and product code. If the
B Ink light remains on after installing the cartridge, it may not be
inserted fully.
Caution:
Do not remove and re-insert cartridges more often than
necessary. Doing so can compromise the needle valve seal and
allow air to enter the ink tubes, causing nozzle damage.
8. Lower the ink levers to their locked position.
5. Make sure the replacement cartridge is the correct color and
remove it from its package.
7 - Epson Stylus Pro 7880/9880 10/07
9. Close the ink compartment covers.
Epson Stylus Pro 7880/9880
Once the cartridge is installed, the printer returns to its
state.
READY
Paper Type and Banding
Banding can be caused by several problems, such as clogged
print head nozzles or a misaligned print head. It can also be
caused by using a paper that is not defined in the Epson
printer driver or in a third-party RIP. To correct this problem,
make sure you select the correct paper type in the driver. See
“Selecting the Correct Media Type Setting” in the User’s
Guide or Printer Guide.
If your paper type is not defined, use the printer’s menu
system to create a custom paper type. See “Optimizing the
Settings for Your Paper” in the User’s Guide or Printer Guide.
Running a Power Cleaning Cycle
You can run a power cleaning cycle from the control panel if
the normal cleaning process is not sufficient to clear the
nozzles. However, the power cycle uses a large quantity of ink,
so it is recommended only as a last resort.
The cartridges need to be at least 50% full to use power
cleaning. You may need to replace a low cartridge to run the
cleaning cycle. After cleaning, you can reinsert the old
cartridge.
1. Print a nozzle check to make sure the print head needs
cleaning. See User’s Guide for instructions.
2. Make sure the printer is ready and the red B Ink light on the
printer’s LCD display is not on or flashing.
3. Press the Menu button.
4. Press the d button until
then press Menu.
5. Press d until
press
Menu. Press Menu again, then press to start the
POWER CLEANING is highlighted, then
power cleaning.
6. Follow the instructions on the LCD display to raise or lower
the ink levers.
7. When cleaning is finished and the
flashing, print the nozzle check again to confirm that the
head is clean.
For effective cleaning, always run a nozzle check between
cycles.
MAINTENANCE is highlighted,
Pause light stops
Checking and Cleaning the Print Head
If your printed image shows a color shift or horizontal lines,
you should check the print head to see if any nozzles are
clogged or deflected. If necessary, the printer will
automatically run a cleaning cycle to clear the nozzles.
1. Press the
2. Press the d button until
press
3. Press
pattern.
The nozzle check pattern is printed and automatically read. If
the printer finds clogged nozzles, it runs a cleaning cycle.
Caution:
Don’t run a cleaning cycle while thick media is loaded in the printer.
Note: You can run a cleaning cycle by holding down the Menu button
for three seconds. You also can check and clean the print head using
your printer utility software. See the User’s Guide for instructions.
Menu button.
TEST PRINT is highlighted, then
Menu. NOZZLE CHECK is selected.
Menu, then press to start printing the nozzle check
If the pattern is still missing segments or has deflections
after a power cleaning cycle, turn the printer off and leave it
overnight. Then clean the print head again the following
morning with regular cleaning cycles. If you still see no
improvement, contact Epson for assistance.
Aligning the Print Head
Aligning the print head is the most important thing you can
do to ensure the best print quality. If banding appears on your
prints, if they look grainy or blurry, or if you see
misregistration or “ghosting,” you may need to align the print
head.
Although you can align the print head using the printer utility
software, it’s also easy to align from the printer’s control panel.
This will do the most thorough job in the shortest time, and
it’s all automatic.
If you haven’t already done so, it’s a good idea to run a nozzle
check before aligning the print head (see User’s Guide). This
ensures that the print head alignment patterns print correctly.
10/07 Epson Stylus Pro 7880/9880 - 8
Epson Stylus Pro 7880/9880
Follow these steps to align the print head using the control
panel:
1. Make sure the printer is turned on. Then load Epson
Enhanced Matte Paper.
Tip:
To properly align the print head, you can also use Epson
Doubleweight Matte Paper or Ultra Premium Photo Paper Luster.
2. Press the Menu button.
3. Press d until
press
Menu. PAPER THICKNESS is highlighted.
4. Press
Menu. The STANDARD setting is selected by default.
HEAD ALIGNMENT is highlighted, then
This is the correct thickness setting for most Epson papers.
5. Press to save the setting.
6. Press l, then press d to highlight
7. Press the
Menu again. UNI-D (uni-directional) is highlighted. This is
Menu button to highlight AUTO, then press
ALIGNMENT.
the type of alignment to start with.
8. Press to start the alignment process.
Each head alignment takes about 7 minutes. The printer’s
white beam sensor reads the alignment pattern and adjusts
the printer automatically. Make sure you don’t open the
front cover or turn off the printer during this process.
9. When the uni-directional alignment is finished, press the d
button until
BI-D 2-COLOR is highlighted. Then press
to start the bi-directional black alignment process.
Removing the Old Blade
Make sure the printer is turned on , then follow th es e ste ps to
remove the blade:
1. Press the
2. Press d until
Menu.
3.
CUTTER REPLACEMENT is highlighted. Press Menu
again.
4. Press . The print head moves to the replacement
position.
REPLACEMENT LABEL
5. Open the front cover.
6. When
the LCD display, hold down the side pin (as shown to the
left) and turn the latch to the right (as shown on the right).
Menu button.
MAINTENANCE is highlighted, then press
OPEN FRONT COVER TO SEE CUTTER
is displayed.
SEE LABEL TO REPLACE CUTTER is displayed on
10. When the bi-directional black alignment is finished, press d
until
BI-D ALL is highlighted. Then press to start the
alignment process.
11. When done, pr ess the
Pause button to exit head
alignment mode.
If you want to fine-tune the automatic alignment process, you
can perform a manual head alignment. See your electronic
User’s Guide for instructions.
Replacing the Paper Cutter Blade
If you notice that your paper isn’t cut cleanly, the cutter blade
may need to be replaced. If you use the blade to cut heavy
stock, you will damage the blade and need to replace it. For a
list of media that are not recommended for use with the
cutter, see the User’s Guide or Printer Guide.
You can check the status of your cutter by printing a status
sheet. See page 6 for instructions. You can obtain a new cutter
blade from Epson (part number C12C815291).
7. Release the side pin. The cutter pops out.
Warning:
The blade is sharp. Be careful when removing it.
9 - Epson Stylus Pro 7880/9880 10/07
Epson Stylus Pro 7880/9880
8. Carefully remove the cutter blade.
Installing the New Cutter Blade
Remove the new blade from its package, then follow these
steps to install it:
1. Insert the new cutter as shown.
the LCD display. When the tank is completely full, the printer
stops working and
MAINTENANCE TANK FULL appears on
the LCD.
You can check how much space remains in the maintenance
tank by viewing its icon on the control panel, shown below.
You can also check its status using the menus, using your
printer software, or by printing a nozzle check sheet.
Maintenance
tank icon*
*The Epson Stylus Pro 9880 has two maintenance tank icons.
The icons show the percentage of space remaining in the
tank(s) as follows:
100–81% 20% to nearly full
80–61% Tank nearly full
60–41% Tank full
40–21% Tank error or no maintenance tank
2. Push down on the side pin while turning the latch to the
left.
3. Close the front cover when you see a message prompting
you to do so. The cutter moves to the home position and
READY appears on the LCD display.
Replacing the Maintenance Tank
The maintenance tank stores ink that gets flushed from the
system during the initial ink charge and manual and
automatic print head cleaning. When the tank is almost full,
the message
MAINTENANCE TANK NEAR FULL appears on
The Epson Stylus Pro 7880 has one maintenance tank (on the
right side), and the 9880 has two (one on either side).
Replacement tanks are available from Epson (part number
C12C890191).
The printer will not print if one of the maintenance tanks is
full. On the Epson Stylus Pro 9880, the right tank is used
more than the left. To maximize tank life, you can switch the
tanks when the right tank reaches approximately 40% to 60%
of capacity.
Follow these steps to replace the tank:
1. Make sure the printer is not printing or performing any
other operations (
READY or PAPER OUT should appear on
the LCD display).
2. If you have the Epson Stylus Pro 9880, check the LCD
display to determine which tank needs to be replaced (left or
right).
10/07 Epson Stylus Pro 7880/9880 - 10
3. Grasp the handle at the bottom of the tank (on the side of
the printer) and gently pull out the maintenance tank.
Caution:
Be careful not to spill ink from the maintenance tank when
removing it. Hold it upright at all times and dispose of it carefully.
4. Place the used tank in the plastic bag included with the new
tank.
5. Insert the new tank.
Epson Stylus Pro 7880/9880
Updating the Driver and Firmware
To ensure that you have the most up-to-date firmware and
driver for your new printer, please visit
Choose your printer and click
Drivers & Downloads to see if
epson.com/support.
there are any updates posted. You may also need to download
the latest version of the EPSON LFP Remote Panel utility.
Check back regularly to maintain compatibility with existing
and future applications.
When your printer is set up and your software is installed, run
the EPSON LFP Remote Panel utility to check your printer’s
firmware ROM version and update it if necessary.
Related Documentation
CPD-24356 Epson Stylus Pro 7880/9880
Printer Guide
CPD-24358 Epson Stylus Pro 7880/9880
Quick Reference Guide
CPD-24357 Epson Stylus Pro 7880/9880
CD-ROM with on-screen User’s Guide
and Network Guide
11 - Epson Stylus Pro 7880/9880 10/07
Loading...