Page 1
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
ESC/VP21 Command User’s Guide for
Home Projectors
Page 2
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
Table of Contents
1. Introduction to ESC/VP21..................................................................................................................................3
2. ESC/VP21 Command Formats...........................................................................................................................4
3. Applicable models ...............................................................................................................................................4
4. Command Table...................................................................................................................................................5
5. Appendix..............................................................................................................................................................8
6. Revision History..................................................................................................................................................9
Copyright Notice:
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.
No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages
resulting from the use of the information contained herein.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchase of this product or third parties for damages,
losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON
CORPORATION(s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable against any damages or problems arising from the use of any options or any
consumable products other than those designated as Original EPSON Products or EPSON Approved Products by SEKO EPSON
CORPORATION.
EPSON is a registered trademark of SEIKO EPSON CORPORATION. EasyMP is a trademark of SEIKO EPSON CORPORATION.
Macintosh, Mac, and iMac are registered trademarks of Apple Computer, Inc. IBM is a registered trademark of International Business
Machines Corporation. Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States of America.
General Notice:
Other product names used herein are also for identification purposes only and may be trademarks of their respective owner. EPSON
disclaims any and all rights in those marks.
©SEIKO EPSON CORPORTION 2003-2009. All rights reserved.
Page 3
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
1. Introduction to ESC/VP21
ESC/VP21 is a control command and protocol for Epson projectors, which is used for A/V controller to control and
monitor Epson projectors. The command codes are comprised of ASCII codes. Therefore the command codes can be
understood very easily and you can easily control projectors using a PC with a terminal emulator such as Microsoft Hyper
terminal.
Since ESC/VP21 is independent of communication protocols. Serial, USB or TCP/IP network can be used to transmit the
commands to projectors.
* Serial connection
A/V controller normally use as serial connection to control projectors. Refer to Appendix for details.
* USB connection
A USB interface can be used to control a projector. Refer to Appendix for details.
* Network connection
After establishing a TCP session, ESC/VP21 commands can be sent to projectors. Refer to ESC/VP.net protocol manual
Page 4
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
2. ESC/VP21 Command Formats
2.1. Set command format
A set command consists of a command and a parameter. Projector returns a colon after executing the command.
There are two types of parameters. One is fixed such as ON, OFF, or 21. Other is a step parameter such as INC, DEC or
INIT.
INC: increments the parameter by one.
DEC: decrements the parameter by one.
INIT: initializes the parameter.
2.2. Get command format
A get command consists of a command and ?. Projector returns a response parameter after executing the command.
2.3. Null command
The null command is as command code of the return key code (Hex 0D). Projector returns a colon。The null command
can be used to confirm that the projector is in operation.
2.4. Illegal commands
Projector returns “ERR” and a return key code (Hex 0D) and a colon when it receives invalid commands.
ERR
：
3. Applicable models
ELP-TW100/TW100H/TS10, EMP-TW10/TW200/TW500/TW10H/TW200H/TW20/TW600/TW520/TW550/
TW800/TW700/TW1000/TW2000, EH-TW2800/TW3000/TW3800/TW4000/TW5000/TW5800/TW2900/
TW3500/TW4400/TW4500/TW5500, EH-TW420/TW450, PL-HomeCinema400/700/720/1080/1080UB/705HD
6100/6500UB/8100/8500UB, PL-ProCinema800/810/1080/1080UB/7100/7500UB/9100/9500UB
Page 5
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
4. Command Table
Command Command Models All Models
ON PWR ON Available (*1) PWR ON
OFF PWR OFF Available
ON MUTE ON Available PWR OFF (note4)
OFF MUTE OFF Available
Black MSEL 00 Available
Blue MSEL 01 Available
SOURCE (note3)
User Logo MSEL 02 Available (*2)
(*1)The "PWR ON" command for TW200 and TW200H needs to prepare for use. First step is to turn on the projector.
And then send the
"SPWRLVL 01" command to the projector after the status of projector goes into the condition that the projector can
receive ESC/VP21 command.
Second steps is to turn off the projector once. The "PWR ON" can work on TW200 and TW200H after the status of
projector becomes the standby state.
•TW500 needs to change the setting item to use "PWR ON" command. To validate the "PWR ON" command of
TW500, "Network Monitoring" of "Operation" in "Setting" menu must be set to ON. The "PWR ON" command can
work on TW500 after the projector is turned off once and the status of projector becomes the standby state.
(*2)TW10/TW10H does not support the User Logo function.
Item Terminal Signal name Command
TW100/
100H
TS10
TW10/
10H
TW200/
200H
TW500
Cyclic within “SOURCE 1x” SOURCE 10
OK OK OK(*3)
OK OK
Analog RGB SOURCE 11
OK OK - - OK
Digital RGB SOURCE 12
- OK - - -
RGB Video SOURCE 13
- OK OK OK OK
YCbCr (*4 Component) SOURCE 14
- - OK OK OK
YPbPr (*4 Component) SOURCE 15
- - OK OK OK
INPUT 1/A
Auto SOURCE 1F
- - - - OK
Cyclic within “SOURCE 2x” SOURCE 20
OK OK OK(*3)
OK OK
Analog RGB SOURCE 21
OK OK OK OK OK
RGB Video SOURCE 22
- OK - - -
YCbCr (*5 Component) SOURCE 23
OK OK - - OK
YPbPr (*5 Component) SOURCE 24
OK OK - - OK
YPbPr SOURCE 25
- - - - OK
INPUT 2/B
Auto SOURCE 2F
- - - - OK
Cyclic within “SOURCE 3x” SOURCE 30
- - - - OK
INPUT 3
Digital RGB SOURCE 31
OK - - - -
Cyclic within “SOURCE Cx” SOURCE C0
- - - OK OK
YCbCr SOURCE C4
- - - OK OK
YPbPr SOURCE C5
- - - OK OK
INPUT 5
Auto SOURCE CF
- - - - OK
VIDEO Cyclic within “SOURCE 4x” SOURCE 40
OK OK OK OK OK
VIDEO (RCA) <= SOURCE 41
OK OK OK OK OK
VIDEO (S) <= SOURCE 42
OK OK OK OK OK
VIDEO (YCbCr)
<= SOURCE 43
OK - - - -
Source change
VIDEO (YPbPr) <= SOURCE 44
OK - - - -
Page 6
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
Item Terminal Signal name Command TW20 TW600
TW700 TW1000 TW2000
Cyclic within “SOURCE 1x” SOURCE 10
OK OK OK OK OK
Analog RGB SOURCE 11
- - - - -
Digital RGB SOURCE 12
- - - - -
RGB Video SOURCE 13
OK - - - -
YCbCr (*4 Component) SOURCE 14
OK OK OK OK OK
YPbPr (*4 Component) SOURCE 15
OK OK OK OK OK
INPUT 1/A
Auto SOURCE 1F
- OK OK OK OK
Cyclic within “SOURCE 2x” SOURCE 20
OK OK OK OK OK
Analog RGB SOURCE 21
OK OK OK OK OK
RGB Video SOURCE 22
- - - - -
YCbCr (*5 Component) SOURCE 23
- - - - -
YPbPr (*5 Component) SOURCE 24
- - - - -
YPbPr SOURCE 25
- - - - -
INPUT 2/B
Auto SOURCE 2F
- - - - -
Cyclic within “SOURCE 3x” SOURCE 30
- OK OK OK OK
INPUT 3
Digital RGB SOURCE 31
- - - - -
Cyclic within “SOURCE Cx” SOURCE C0
- OK OK OK -
SCART (*6) SOURCE C3
- OK OK OK -
YCbCr SOURCE C4
- OK OK OK -
YPbPr SOURCE C5
- OK OK OK -
INPUT 5
Auto SOURCE CF
- OK OK OK -
HDMI2 HDMI SOURCE A0
- - - - OK
VIDEO Cyclic within “SOURCE 4x” SOURCE 40
OK OK OK OK OK
VIDEO (RCA) <= SOURCE 41
OK OK OK OK OK
VIDEO (S) <= SOURCE 42
OK OK OK OK OK
VIDEO (YCbCr)
<= SOURCE 43
- - - - -
Source
change
VIDEO (YPbPr) <= SOURCE 44
- - - - -
Item Terminal Signal name Command
TW2800
TW3000
TW3800
HC6100
PC7100
TW4000/
HC6500U
B
TW5000/
PC7500U
B
TW2900
TW3500
HC8100
PC9100
TW4400
TW4500
HC8500UB
Cyclic within “SOURCE 1x” SOURCE 10
OK OK OK OK OK
Analog RGB SOURCE 11
- - - - -
Digital RGB SOURCE 12
- - - - -
RGB Video SOURCE 13
- - - - -
YCbCr (*4 Component) SOURCE 14
OK OK OK OK OK
YPbPr (*4 Component) SOURCE 15
OK OK OK OK OK
INPUT 1/A
Auto SOURCE 1F
OK OK OK OK OK
Cyclic within “SOURCE 2x” SOURCE 20
OK OK OK OK OK
Analog RGB SOURCE 21
OK OK OK OK OK
RGB Video SOURCE 22
- - - - -
YCbCr (*5 Component) SOURCE 23
- - - - -
YPbPr (*5 Component) SOURCE 24
- - - - -
YPbPr SOURCE 25
- - - - -
INPUT 2/B
Auto SOURCE 2F
- - - - -
Cyclic within “SOURCE 3x” SOURCE 30
OK OK OK OK OK
INPUT 3
Digital RGB SOURCE 31
- - - - -
Cyclic within “SOURCE Cx” SOURCE C0
- - - - -
YCbCr SOURCE C4
- - - - -
YPbPr SOURCE C5
- - - - -
INPUT 5
Auto SOURCE CF
- - - - -
HDMI2 HDMI SOURCE A0
OK OK OK OK OK
VIDEO Cyclic within “SOURCE 4x” SOURCE 40
OK OK OK OK OK
VIDEO (RCA) <= SOURCE 41
OK OK OK OK OK
VIDEO (S) <= SOURCE 42
OK OK OK OK OK
VIDEO (YCbCr)
<= SOURCE 43
- - - - -
Source
change
VIDEO (YPbPr) <= SOURCE 44
- - - - -
Page 7
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
Item Terminal Signal name Command
TW5500
PC9500UB
TW420
HC700
TW450
HC705HD
Cyclic within “SOURCE 1x” SOURCE 10
OK OK OK
Analog RGB SOURCE 11
- OK OK
Digital RGB SOURCE 12
- -
RGB Video SOURCE 13
- -
YCbCr (*4 Component) SOURCE 14
OK OK
(*7)
OK
(*7)
YPbPr (*4 Component) SOURCE 15
OK -
INPUT 1/A
Auto SOURCE 1F
OK OK OK
Cyclic within “SOURCE 2x” SOURCE 20
OK -
Analog RGB SOURCE 21
OK -
RGB Video SOURCE 22
- -
YCbCr (*5 Component) SOURCE 23
- -
YPbPr (*5 Component) SOURCE 24
- -
YPbPr SOURCE 25
- -
INPUT 2/B
Auto SOURCE 2F
- -
Cyclic within “SOURCE 3x” SOURCE 30
OK OK OK
INPUT 3
Digital RGB SOURCE 31
- -
Cyclic within “SOURCE Cx” SOURCE C0
- -
YCbCr SOURCE C4
- -
YPbPr SOURCE C5
- -
INPUT 5
Auto SOURCE CF
- -
HDMI2 HDMI SOURCE A0
OK -
VIDEO Cyclic within “SOURCE 4x” SOURCE 40
OK - OK
VIDEO (RCA) <= SOURCE 41
OK OK OK
VIDEO (S) <= SOURCE 42
OK OK OK
VIDEO (YCbCr)
<= SOURCE 43
- -
Source
change
VIDEO (YPbPr) <= SOURCE 44
- -
(*3)Only when TW10 is connected, the source is not cycled within a signal that can select on a terminal by these commands.
(*4)This signal is selected when TW10 and TW20 is connected.
(*5)This signal is selected when TW500 is connected.
(*6)This signal is selected when TW600/520/550/800/700/1000 is connected.
(*7)This command is can be used only for get.
Page 8
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
5. Appendix
5.1. Communication specification
A projector and a computer can be connected using a serial or USB port. The projector can be remotely controlled by
sending commands to the projector.
Serial Connection
(TW100,TS10,TW10,TW200,TW500,TW10H,TW200H,TW20,TW600/520/550/800,TW700,TW1000,TW2000,
TW3000/TW4000/TW5000, TW2900/TW3500/HomeCinema8100/ProCinema9100, TW4400/TW4500/
HomeCinema8500UB/ProCinema9500UB, TW450/HomeCinema705HD)
・ Select RS-232C at Advanced Setting of the Menu.
・ Communication condition
Baud rate : 9600bps
Data length : 8 bits
Parity : No
Stop bit : 1 bit
Flow control : No
・ Connector : D-Sub 9pin
・ Projector input : Control(RS-232C)
Page 9
ビジネスプロジェクター用 ESC/VP21 コマンド使用ガイド
ESC/VP21 Command User
’
s Guide for Home Projectors
6. Revision History
Revision Issued date Page Description
A Oct 19,2005 All pages First Release
B Sep 29,2006 All pages Addition of TW700
C Mar 19,2007 All pages
Addition of TW1000
D Jun 4,2007 All pages
Correction of “Applicable Model”.
E Dec 14,2007 All pages
Addition of TW2000
F Nov 14,2008 All pages
Addition of TW3000 and TW4000
G Dec 2, 2008 All pages
Addition of TW5000 and TW420
H Mar 11, 2010 All pages
Addition of TW2900/3500/HomeCinema8100/ProCinema9100,
TW4400/TW4500/HomeCinema8500UB/ProCinema9500UB
TW450/HomeCinema705HD
Loading...