Epson EcoTank ET-4760 Start Guide

ET-3760/ET-4760

Start Here

IMPORTANT: Before using this product, make sure you read these instructions and the safety instructions in the online User’s Guide.

Important Safety Instructions: When using telephone equipment, you

should always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury, including the following:

• Do not use the Epson® product near water.

• Always keep this guide handy.

• Avoid using a telephone during an electrical storm. There may be a remote risk of electric shock from lightning.

•

Do not use a telephone to report a gas leak in the vicinity of the leak.

Caution: To reduce the risk of fire, use only a No. 26 AWG or larger

telecommunication line cord.

2 Lift up the scanner unit. Remove all protective materials

from inside the product.

Caution: Do not touch the ﬂat white cable or the ink tubes and

their translucent cover.

Fill ink tanks

The illustrations show the ET-4760, but the steps are the same for all models, unless otherwise speciﬁed.

Unpack

Note: Do not open the ink bottles until you are ready to ﬁll the ink

tanks. The ink bottles are vacuum packed to maintain reliability.

1 Remove all protective materials from the product.

Warning: Keep the ink bottles out of the reach of children and do not

drink the ink.

Caution: This product requires careful handling of ink. If ink spills,

wipe it off immediately with a damp towel to avoid permanent stains. If ink gets on your clothes or belongings, it may not come off.

Note:

• Epson cannot guarantee the quality or reliability of third-party ink.

• Use the ink bottles included with the printer to set up the product. Part of the ink will be used to charge the print head. These bottles may print fewer pages compared with replacement ink bottles.

1 Open the ink tank cover, then open the cap for the

black ink.

2 Unpack the black (BK) ink bottle. Hold the ink bottle

upright and slowly turn the bottle cap to remove it.

Caution: Do not shake or squeeze the ink bottles. Do not touch

the top of the ink bottle after its cap is removed.

3 Insert the ink bottle into the ﬁlling port, as shown below.

Note: Refer to the color-coded sticker to identify the color of

each tank. Do not force the bottles into position; they are keyed for each color.

4 Wait for the ink to ﬁll the tank.

Do not squeeze the bottle. Ink ﬂows into the tank and stops automatically when the ink is ﬁlled to the upper line.

Note: If ink does not ﬂow from

the bottle, lift and reinsert the bottle.

Caution: After setup, periodically

inspect the ink level to ensure it is not below the lowest line on the tank. Prolonged use when ink is below the lowest line could damage the product. See the online User’s Guide for reﬁlling instructions.

5 When the ink tank is full, remove the ink

bottle and replace the bottle cap. Place the remaining ink aside; you will need it later.

Note: Do not leave the ink bottle inserted;

otherwise the bottle may be damaged or ink may leak.

10 Raise the control panel, then press the power button to

turn on the product.

Note: If an error message appears, turn off the product and

check that no protective material has been left inside the product.

11 ET-3760: Press or to select your language on the

LCD screen, then press the OK button.

ET-4760: Select your language, country, and time.

Note: You can change these settings later using the product’s

control panel. For more information, see the online User’s Guide.

Follow steps 12 and 13 to continue ink charging.

12 When the message to see the Start Here sheet appears

on the LCD screen:

ET-3760: Press the OK button, then press and hold the

help button for 3 seconds.

6 Close the ink tank cap.

7 Repeat the previous steps for the other colors.

8 Close the ink tank cover and then the scanner unit.

9 Connect the power cord to the back of the product and to

an electrical outlet.

ET-4760: Press and hold the

help button for 3 seconds.

13 When the ink conﬁrmation message appears on the LCD

screen, select Done to start charging the ink. Ink charging takes approximately 10 minutes. A message appears when ink charging is complete. Press the OK button to continue.

Caution: Do not turn off the product, raise the scanner unit, or

load paper while the product is charging or you’ll waste ink.

Note: The included ink bottles are designed for reliable printer

setup and cannot be resold. After setup, the remaining ink is available for printing.

14 To complete ﬁlling the ink tanks, repeat steps 1 through 7

using the remaining ink in the bottles.

Note: Replace the bottle cap before disposing of the bottles.

15 Close the ink tank cover and scanner unit.

16 Select Next and follow the on-screen instructions to reset

the ink levels.

Caution: Do not connect to your computer yet.

17 Follow the on-screen instructions to adjust the print

quality. Press the OK button to continue.

Note:

• You need to load paper before you can adjust the print quality. See “Load paper” on the back of this sheet for details.

• You can change these settings later using the product’s control panel. For more information, see the online User’s Guide.

+ 2 hidden pages